ANIServer,EPMServer is down

Hi,
In our CISCO LMS portal,Campus service is not running,
Error is showing ANIServer,EPMServer is down
Thanks
Avijit

No. It is working for me.
Allan

Similar Messages

Processes MACUHIC, UTLITE, WlseUHIC, ANIServer, UTManager are down

Hi all, not sure if anyone has run into this problem before, but I'm having an issue with my CiscoWorks 4.0.1 software app. When I look at Critical Message Window I see the following mesages. "Processes MACUHIC, UTLITE, WlseUHIC, ANIServer, UTManager are down" Any help would be appreciated.
James

Hmmm. A shot in the (almost) dark comes to mind - Is your server setup to allow Java updates automatically? CiscoWorks is very dependent on Java behaving as expected (both on the server and client side). An unmanaged Java update could potentially "break" some Java-dependent bits - of which there are many.
When I was asking about manual process starts I was thinking from the LMS admin panel. (Admin > System > Server Monitoring > Processes.)
Finally, I note from the Admin Guide Table 3-2 that the processes you mention have the ANIdbengine process in common as a dependency. Is it running OK?

Cannot connect to ANIServer 7.0 - Unknown Error

Hello!
The topology stopped working. Shows that it can not connect to ANIServer for unknown reason.
In the shell is visible that the services and ANIServer ANIDbEngine are down.
But I can not start because automatically return down.
Process State Pid ******* ***** *** ESS Program started - No mgt msgs received 4649 EssMonitor Running normally 4661 EventFramework Program started - No mgt msgs received 4701 SyslogCollector Running normally 4702 RMEDbEngine Program started - No mgt msgs received 4703 DfmBroker Running normally 4803 DfmServer Running normally 4883 DfmServer1 Running normally 4884 FHDbEngine Program started - No mgt msgs received 4885 EPMDbEngine Program started - No mgt msgs received 5091 EPMServer Running normally 5172 AdapterServer Program started - No mgt msgs received 5310 AdapterServer1 Program started - No mgt msgs received 5311 FHServer Running normally 5313 INVDbEngine Program started - No mgt msgs received 5315 PMServer Running normally 5396 IpmDbEngine Program started - No mgt msgs received 5553 UPMDbEngine Program started - No mgt msgs received 5626 UPMDbMonitor Running normally 5683 ANIDbEngine Administrator has shut down this server 0 MACUHIC Running normally 8371 UTLITE Administrator has shut down this server 0 CmfDbEngine Program started - No mgt msgs received 5785 CmfDbMonitor Running normally 5818 DFMLogServer Program started - No mgt msgs received 5820 DFMCTMStartup Administrator has shut down this server 0 FHPurgeTask Transient terminated 0 DFMMultiProcLogger Program started - No mgt msgs received 5822 CSDiscovery Transient terminated 0 DCRDevicePoll Transient terminated 0 CSRegistryServer Running normally 5823 Tomcat Program started - No mgt msgs received 5828 TomcatMonitor Running normally 5902 Apache Running normally 6475 DCRServer Running normally 6487 CMFOGSServer Program started - No mgt msgs received 6564 TISServer Program started - No mgt msgs received 6565 DFMOGSServer Program started - No mgt msgs received 6634 NOSServer Running normally 6704 PTMServer Running normally 6706 InventoryCollector Running normally 6707 Interactor Program started - No mgt msgs received 6826 InventoryCollector1 Program started - No mgt msgs received 6827 Interactor1 Program started - No mgt msgs received 6933 UPMProcess Running normally 6934 WlseUHIC Running normally 8374 UTManager Running normally 8376 VNMServer Program started - No mgt msgs received 8377 EssentialsDM Running normally 6935 ICServer Running normally 7188 EnergyWise Running normally 7400 ConfigMgmtServer Running normally 7401 PMCOGSServer Program started - No mgt msgs received 7402 ConfigUtilityService Running normally 7403 CAAMServer Running normally 7417 IPMOGSServer Program started - No mgt msgs received 7431 TopoServer Program started - No mgt msgs received 7433 LicenseServer Program started - No mgt msgs received 7435 FDRewinder Never started 0 NameServer Program started - No mgt msgs received 7436 NameServiceMonitor Program started - No mgt msgs received 7573 EDS Running normally 7623 ANIServer Administrator has shut down this server 0 UTMajorAcquisition Never started 0 EDS-GCF Running normally 8068 jrm Running normally 8069 DataPurge Administrator has shut down this server 0 IPMProcess Program started - No mgt msgs received 8199 CTMJrmServer Running normally 8200 SyslogAnalyzer Running normally 8303 ChangeAudit Program started - No mgt msgs received 8304 1060 Never started 0 1348 Never started 0 diskWatcher Running normally 8305
Does anyone know the solution to this problem?
Thanks in advance!

Most of the it has been noticed that the ANIServer may fail if aniserver.properties is corrupted. The simplest way to check is to compare size of aniserver.properties against aniserver.properties.orig, if aniserver.properties has a smaller size you should repair it. It should contains more information thatn in ANIServer.properties.orig. To confirm you can share both the files # NMSROOT/campus/etc/cwsi/.
Instructions how to restore the properties file:
1) Stop the daemon manager : win: net stop crmdmgtd | sol: /etc/init.d/dmgtd stop
2) Copy ANIServer.properties.orig ANIServer.properties
3) Edit the ANIServer.properties
DEVICESROOT=.
into
DEVICESROOT=NMSROOT\\campus\\lib\\classpath
(replace NMSROOT with the correct directory where NMS is insralled. Default location is C:\PROGRA~1\CSCOPX for windows and /opt/CSCOpx/ for solaris. Note the use of two backslashes in the DEVICEROOT properties. )
4) Start the daemon manager : win: net start crmdmgtd | sol: /etc/init.d/dmgtd start
Now the ANIServer process should be in "Running with busy flag" State.
-Thanks

LMS 4.2 ANIserver problem

Hello, we are running LMS 4.2.2 and our Topology maps have stopped working and I noticed that the ANIserver process is down.
By tailing the /var/adm/CSCOpx/log/dmgtd.log i got the messages below, any idea whats going on?
A shutdown of LMS + reboot did not help.
BR /Crille
Jan 9 12:39:12 xxx dmgt[3318]: #3007:TYPE=INFO:Started application(ANIServer) "/opt/CSCOpx/lib/jre/bin/java -Xbootclasspath:/opt/CSCOpx/lib/jre/lib/jsse.jar:/opt/CSCOpx/MDC/tomcat/webapps/campus/WEB-INF/classes:/opt/CSCOpx/MDC/tomcat/webapps/campus/WEB-INF/lib/log4j.jar:/opt/CSCOpx/www/classpath/jacorb.jar:/opt/CSCOpx/lib/jre/lib/rt.jar:/opt/CSCOpx/lib/jre/lib/jce.jar -Xminf0.1 -Xmaxf0.1 -Djava.class.path=/opt/CSCOpx/campus/lib/classpath/castor-1.2.jar:/opt/CSCOpx/campus/lib/classpath/commons-logging-1.1.1.jar:/opt/CSCOpx/campus/www/classpath/jndi.jar:/opt/CSCOpx/campus/www/classpath/providerutil.jar:/opt/CSCOpx/lib/jre/lib/ext/dnsns.jar:/opt/CSCOpx/campus/lib/classpath:/opt/CSCOpx/campus/www/classpath:/opt/CSCOpx/lib/classpath:/opt/CSCOpx/www/classpath:/opt/CSCOpx/MDC/tomcat/webapps/campus/WEB-INF/lib/ctm.jar:/opt/CSCOpx/lib/classpath/cmfjms.jar:/opt/CSCOpx/MDC/tomcat/webapps/campus/WEB-INF/lib/xalan.jar:/opt/CSCOpx/MDC/tomcat/webapps/campus/WEB-INF/lib/xerces.jar:/opt/CSCOpx/lib/jre/lib/jsse.jar:/opt/CSCOpx/lib/jre/lib/jce.jar:/opt/CSCO
Jan 9 12:39:16 xxx dmgt[3318]: #3021:TYPE=INFO:Died method called for process (ANIServer, pid=10851).#015
Jan 9 12:39:16 xxx dmgt[3318]: #2135:TYPE=WARNING:Stale socket -1 while establishing connection with ANIServer: Bad file descriptor. #015

Topology is dependent on ANIServer and it may not work if it goes down. Better is you share aniserver.properties and aniserver.log and ani.log from your server for more insight.
-Thanks
Vinod
**Rating Encourages contributors, and its really free. **

Tomcat error in DFM 3.0.5

Hi,
On a LMS 3.0.1, DFM 3.0.5, I've got a Tomcat error, when I want to see the "Alerts and Activity" (see attachement)
Trying to solve the problem, i've made several try:
1. I purged the dfm database (CSCOpx/bin/dbRestoreOrig.pl dsn=dfmInv dmprefix=INV, CSCOpx/bin/dbRestoreOrig.pl dsn=dfmFh dmprefix=FH,
CSCOpx/bin/dbRestoreOrig.pl dsn=dfmEpm dmprefix=EPM)
2. Import devices from DCR (almost 400 devices). I can see all the devices in "Device Management/Device summary"
3. re-install DFM 3.0.5
and this doesn't solve the problem
I attach the "pdshow", if it can help.
Which log file can help you ?
thanks

I add:
As the post (https://supportforums.cisco.com/message/1328737#1328737), I do this:
"NMSROOT/objects/db/win32/dbsrv9 -f NMSROOT/databases/dfmEpm/dfmEpm.db"
and restore the database by
"NMSROOT/bin/perl NMSROOT/bin/dbRestoreOrig.pl dsn=epm dmprefix=EPM"
in attachement, the new pdshow (the EPMDbEngine is started, but the EPMServer is down)
And still "tomcat error"...
If you have an idea...

Processes ANIServer are down-how to get it to stay on?

User Tracking has not updated since October. Have looked at the other posts and have followed the instructions but still no joy. Attached the pdshow file, ani.log and aniserver.log. I had thought it was a java update that might have caused it. Any help would be much appreciated. Thanks.
Am I in the wrong place for this discussion?
Message was edited by: Lucy Thompson

Close All Apps and reboot.
Go to the home screen first by tapping the home button. Double tap the home button and the recents tray will appear with all of your recent apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

LMS 4.0 - DCRServer is down

I go to Device Allocation Settings from the getting started page. and on the left side i get the following message
DCRServer is down or may not be completely up. Check if the DCRServer process is running.
I dont see any service by that name, I tried rebooting, running
C:\Program Files (x86)\CSCOpx\bin>DCR.bat
This is a new installation on a new server windows 2008 R2 STD 64bit
Xeon [email protected]
4GB Ram, virtual set to 8192 min.
HD has 48.7 GB free
No AV on it yet,
I am logged in as administrator local,
Server is in a VM Environment
J.P.

My tests on different operationg systems (2003 R2 x86, 2008 R1 x86) led to the same results
Installation log file (2008 R1 x86) attaced. The size of my "lms-4-0-Win-eval.exe" file is 1 964 554 Кbytes.
> pdshow DCRServer
        Process= DCRServer
        State = Failed to run
        Pid    = 0
        RC     = -14
        Signo = 1073741810
        Start = N/A
        Stop   = 10/5/2010 2:29:28 PM
        Core   = Not applicable
        Info   = Application failed or was registered incorrectly.
> pdshow -brief
Process               State                                     Pid
UPMDbEngine           Program started - No mgt msgs received    484
UPMDbMonitor          Running normally                          2328
Tomcat                Program started - No mgt msgs received    2348
TomcatMonitor         Running normally                          2412
Apache                Program started - No mgt msgs received    3228
RMEDbEngine           Program started - No mgt msgs received    4508
Proxy                 Program started - No mgt msgs received    4548
NameServer            Program started - No mgt msgs received    4556
NameServiceMonitor    Running normally                          4616
EDS                   Running normally                          4656
LicenseServer         Program started - No mgt msgs received    5012
IpmDbEngine           Program started - No mgt msgs received    5024
INVDbEngine           Program started - No mgt msgs received    5136
FHPurgeTask           Never started                             0
FHDbEngine            Program started - No mgt msgs received    5324
ESS                   Program started - No mgt msgs received    5380
EssMonitor            Running normally                          5484
EventFramework        Program started - No mgt msgs received    5768
PMServer              Running normally                          5776
SyslogCollector       Running normally                          6104
EPMDbEngine           Program started - No mgt msgs received    6112
EPMServer             Program started - No mgt msgs received    4964
FHServer              Running normally                          5696
diskWatcher           Running normally                          5724
DFMMultiProcLogger    Program started - No mgt msgs received    5748
DFMLogServer          Program started - No mgt msgs received    5744
DFMCTMStartup         Administrator has shut down this server   0
DfmBroker             Program started - No mgt msgs received    5952
DfmServer             Running normally                          6200
DfmServer1            Running normally                          6208
DCRDevicePoll         Never started                             0
CSSCPServer           Program started - No mgt msgs received    6216
CSRegistryServer      Running normally                          6224
CSDiscovery           Never started                             0
CmfDbEngine           Program started - No mgt msgs received    6232
CmfDbMonitor          Running normally                          7164
DCRServer             Failed to run                             0
CMFOGSServer          Never started                             0
EssentialsDM          Never started                             0
ConfigMgmtServer      Never started                             0
ConfigUtilityService Never started                             0
ICServer              Never started                             0
EnergyWise            Never started                             0
PMCOGSServer          Never started                             0
IPMOGSServer          Never started                             0
TISServer             Never started                             0
DFMOGSServer          Never started                             0
InventoryCollector    Never started                             0
Interactor            Never started                             0
InventoryCollector1   Never started                             0
Interactor1           Never started                             0
NOSServer             Never started                             0
PTMServer             Never started                             0
UPMProcess            Never started                             0
EDS-GCF               Running normally                          7676
jrm                   Running normally                          6572
CTMJrmServer          Never started                             0
ChangeAudit           Never started                             0
SyslogAnalyzer        Never started                             0
DataPurge             Administrator has shut down this server   0
IPMProcess            Never started                             0
ANIDbEngine           Program started - No mgt msgs received    7940
ANIServer             Never started                             0
UTMajorAcquisition    Never started                             0
MACUHIC               Running normally                          8148
UTLITE                Running normally                          8152
UTManager             Never started                             0
VNMServer             Never started                             0
WlseUHIC              Never started                             0
AdapterServer1        Program started - No mgt msgs received    8164
AdapterServer         Program started - No mgt msgs received    8172

EPMServer processes don't die after dmgtd stop - LMS 4.2 Solaris

I am unable to kill EPMServer processes after shutting down LMS 4.2 on Solaris 10. There are still 60 or so EPMServer processes running. Killing them manually does not work as they appear to restart again after killing. Only way to knock them off is to reboot the system. Why does dmgtd stop not kill all LMS processes and is there a patch required for LMS 4.2 or Solaris 10 that would help?
EPMServer processes attached:
Thanks.

Any luck on resolving this problem? This is happening on multiple servers. Cannot kill EPMServer processes manually or by running .../etc/init.d/dmgtd stop to kill server. Killing processing directly will respawn same processes again. Only recourse is to reboot with these processes active.
: ps -ef|grep CSC
casuser 29811 29803   0 18:36:49 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
    root 18722 16794   0 10:32:21 pts/2       0:00 grep CSC
casuser   546     1   0   Aug 15 ?           0:00 /bin/bash /opt/CSCOpx/MDC/tomcat/webapps/rme/WEB-INF/compliancemgr/compliance/b
casuser 29803     1   0 18:36:34 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29808 29800   0 18:36:48 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29800     1   0 18:36:33 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29821 29811   0 18:37:05 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29817 29808   0 18:37:04 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29819 29810   0 18:37:05 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29790     1   0 18:35:37 ?           0:00 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29799     1   0 18:36:33 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29814 29805   0 18:36:51 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29839 29827   0 18:37:36 ?           0:00 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29810 29799   0 18:36:49 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29805     1   0 18:36:35 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29824 29814   0 18:37:09 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29827 29817   0 18:37:20 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29829 29819   0 18:37:21 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29831 29821   0 18:37:21 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29838 29829   0 18:37:36 ?           0:00 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29833 29824   0 18:37:24 ?           0:01 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29840 29831   0 18:37:37 ?           0:00 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5
casuser 29841 29833   0 18:37:40 ?           0:00 CSCO.EPMServer -Xms64M -Xmx1024m -cp:p conf/epm/patch:lib/classpath//cesar-v0-5

LMS 4.0.1 - ANI Server may be down

Hi all,
I'm facing a problem with my LMS 4.0.1...when I tried to access anything under "Admin> Collection Settings> Data Collection>" I received the following message:
"Error while loading. ANI Server may be down. Please check for ANI Server Status in Admin -> System -> Server Monitoring -> Processes"
And then, all fields are blank in:
SNMP Timeouts and Retries
Data Collection Schedule
Data Collection Critical Devices Poller
But everything is OK, the process is running (with busy flag set) on pdshow...I tried to restart ANIServer with "pdterm ANIServer/pdexec ANIServer" and other actions mentioned in other posts but no luck at all...
Maybe It's related to another problem, where my shadow directory is not being updated, after change any configuration...in any device...
Could you please help me?
Regards,
Vicente Pires

Hi ,
Found some errors and exception in the log..
We need to follow the below steps to fix the issue::
-we need to re-initialize the ANIdatabase ::
1.stop the daemon manager :
/etc/init.d/dmgtd stop
net stop crmdmgtd
2.Go to : /opt/CSCOpx/bin/ and issue the command :
Run the below command:    /opt/CSCOpx/bin/perl dbRestoreOrig.pl dsn=ani dmprefix=ANI
windows::
NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
3.Start the Daemon manager ::
/etc/init.d/dmgtd start
net start crmdmgtd
***IMP***   Re-initialize the ANI database will not lose any of the history information of the device. Also ANI database does not contain any historical information as soon as the above steps are complete you need to run and new DATA COLLECTION followed by User tracking Acquisition and then check the issue.
Data collection:: Go to Admin > Collection Settings > Data Collection > Data Collection Schedule   under "start Data Collection" > For "All Device" >> click "START"
User tracking :: Inventory > User Tracking Settings > Acquisition Actions
hope it will help
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cannot Connect to ANIserver

Hi.
I'm after a reboot on LMS 2.6 server, the CM home page started showing the following message: "Cannot connect to ANI Server since it is down". I followed the procedures as in the thread "Ciscoworks ANI server cannot connect, Joe Clark please help", but, in the end, after I restarted yhe Damon Manager, all seervices came up, except for the ANI database engine. After I started this serrvice manually, it came up, but the ANI.log file reappeared and the message on the CM home became "Please wait... ANIServer is still initializing."
The result for the pdreg command is below:
C:\>pdreg -l ANIDbEngine
        Process      = ANIDbEngine
        Path         = C:\PROGRA~1\CSCOpx\objects\db\win32\dbsrv9.exe
        Flags        =
        Startup      = Started automatically at boot.
        Dependencies = Not applicable
The result for the pdshow command is attached.
Hope Joe Clark or anyone can help me to.
Thanks in advance.

Before your last message, I've disabled all DFM polling and SNMP trap receiving. After that, the RME home started working normally and I was able to manage jobs once again. You were right, the server coudn't handle all the traps and the polling, but even after disabling those, the CM home still shows the JRM down message. I tried stopping and restarting the JRM, like you suggested, but the problem persisted.
The system is a Windows 2003 on a VMWare ESXi. The hardware is a dual Xeon with 4GB of dedicated RAM to the LMS server. I don't have the clock informations now, but I can provide it tomorrow.
P.S.: Is there any clean way to prevent DFM from processing SNMP traps? For test purpooses, I changed the SNMP port, but it makes Windows to generate lots of ICMP port unreachable packets and I don't intend to leave it this way.

Adobe Photoshop CS2 shuts itself down after printing..

Not sure whether I'm in the right place to post this..
In my workplace, we just bought some new iMacs for design class. They are a 2GHz with Intel Core Duo, and has 1GB 667 Mhz DDR2 SDRAM, and running Mac OSX 10.4.8.
The Photoshop CS2 is version 9.0
I've config-ed the five new iMacs so they can print to a printer, using IP printing. Problem is, most of the time after the students sends the document they want to print to the printer, Photoshop CS2 just shuts itself down. Then the dialog box saying 'the software just unexpectedly quit' appears.
It is confusing me, because our older iMacs (that's not an Intel-based) doesn't have this problem, at all.
is it something to do with CS2 compatibility with Intel-based Macs? or something else.. what needs to be done to stop this annoying problem?
Regards,
Meru
iMacs Mac OS X (10.4.8)
eMacs, iBook G4s Mac OS X (10.3.9)

Windows 7 error “key not valid for use in specified state” | The Oracle Instructor

On Screen Keyboard Glitch in Tablet Mode - On Screen Keyboard minimizes / disappears / slides down

Hi there -
New Yoga owner here ( just bought it yesterday) and within minutes of setting the computer up I noticed that the on screen keyboard was malfunctioning when the yoga is in tablet mode. Specifically, it pops up for about a second and then, without me touching or clicking or doing anything, it quickly slides back down. repeated attempts to bring up the keyboard end up, frustratingly, with the same result. what is perplexing to me is the on screen keyboard works fine in laptop mode (when I need it least).
Someone else already started a post on this BUT it was marked as 'solved' (which it wasn't) so I figured I'd start new thread. The solution on the previous thread was to simply 'refresh' windows to get rid of any new drivers that were downloaded since purchasing the yoga, but I did not download or update anything prior to this problem arising (as I said, the problem seemed to occur within a few minutes of turning the machine on for the first time). In any case, I tried the refresh and it did not work so clearly my problem is not that I downloaded an incompatible or faulty driver. Please Help! I love this machine and I'm trying to see past the other flaws I've noticed so far (subtle screen flickering, inconsistent touch sensitivity etc), but this issue is starting to really undermine my confidence in the product quality and, from a productivity standpoint, it is a real deal breaker to not have full tablet functionality.
Solved!
Go to Solution.

I had the same problem with the disappearing virtual keyboard within hours of starting to use my new Yoga 13. I read somewhere that it was a problem with an incompatible Synaptics driver, and when I looked in the control panel, it showed that the Synaptics driver had been updated on my Yoga as of the day I bought it. I think somehow by agreeing to automatic updates of the software, the Synaptics driver is updated to an incompatible version. So what I did was I removed the Synaptics driver, using the Windows program uninstaller tool, rebooted, and then found the Synaptics driver at the Lenovo site which is specifically labelled as the Yoga 13 driver. I installed that, and the keyboard is now working fine.

Drop down text options

I'm looking for feedback on other options for displaying drop
down text. I'm getting feedback from my users that they don't
understand that green italic text (or what ever format is used)
assumes drop down text. Most people are now used to seeing collapse
and expand icons to represent drop down information. I have used
the twisties in some of my projects but in this specific case, i am
using the Show/Hide All script and there appears to be a conflict
with the 2 scripts.
I'm just curious if there are other methods used to represent
or display that an item on the page is a drop down link, other than
expand or collapse icons.

Are you talking about the twisty / show hide methods on my
site? If so please see the introductory topic that refers to a
script that does allow both to work together.

How to get ALL values as default for a drop down box in JSF

Hi,
I have a drop down box in JSF page which retrieves values from LOVCache.java. I have values like Company, Client, User, ALL in the drop down box.
By default blank value is selected for the drop down box. I want to make ALL(which retrieves data for all the values) as default value for the drop down box.
Could any body help me? Any help must be appreciated.
Thanks,
Aseet

Thanks Nikhil. But I am fetching the values from the LOVCache.java.
I am using <af:selectManyChoice>. Is there any way I can use LOVCache.java value for selecting default values instead of hard coding?
I mean to say can I write
unselectedLabel="#{LOVCache.entityTypeSelectionList.anyValue}"
where LOVCache.entityTypeSelectionList is used to populate the drop down box.
Regards,
Aseet

My macbook pro no longer connects to my TV with the mini dvi to hdmi adapter. A while ago the computer fell down and hit the cable. How can I tell if the computer is working ok. Doesn't show mirroring any more.

My macbook pro no longer connects to my TV with the mini dvi to hdmi adapter. A while ago the computer fell down and hit the cable. How can I tell if the computer is working ok. Doesn't show mirroring any more. Was working while watching a movie but when I pulled it out from the computer and put it back in the system would no longer mirrorr the screen on the TV.

The best option is an appointment at an Apple store genius bar. The evaluation will be for FREE!
Ciao.

ANIServer,EPMServer is down

Similar Messages

Maybe you are looking for