AP with different country code

Dears
Customer has following accesspoints & WLCs on their Network
AIR-LAP1522AG-A-K9 it is connected to 1st 4404 WLC and countrycode is US..(APs including MESH)
AIR-LAP1252AG-E-K9 it is connected to 2nd 4404 WLC and countrycode is SA
and
AIR-LAP1142N-E-K9
AIR-LAP1252AG-E-K9
AIR-CAP3502I-E-K9 these aps are connected to 3rd 4404 WLC and countrycode is GB
Now they bought AIR-CT8510-1K-K9 WLCs (1000AP License) and
Following APs
AIR-CAP3602I-E-K9
AIR-CAP1552E-M-K9
Am I able to integrate all to new 8510. In that case What country code I will use?
OR Do I need to keep different WLCs for each AP type
Thanks and Regards
Deva

In order for the WLC to be able to manage the LAP, the LAP should discover the controller and register with the WLC. There are different methods that an LAP uses in order to discover the WLC. For detailed information on the different methods the LAPs use to register to the WLCs, refer to Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
This document describes the configuration steps needed to register the LAP to the WLC and for basic operation of the LWAPP wireless network.
Please Check the below link for configuration.
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml

Similar Messages

Acquisition tax in Belgium/Germany-Posting with different tax codes

Dear Friends,
Does anyone have experience working with Acquisition tax in Belgium and German where the goods and services purchased within EU have 21% -input and output tax such that it is ZERO. But still Tax authorities need to see both input and output tax amount with different tax code such as under:
Expense a/c Dr 100
Payable a/c Cr 100
Input VAT a/c Dr 21 - Tax code A1
Output VAT a/c Cr 21 - Tax code B1
Any help as to how to post the above entry and how to customize tax code to get the above result and any changes if required in country code tax calculation procedure will be greatly appreciated.
Thanks,
Pinky

Hi Pinky,
When you define your tax codes, the system defaults certain tax types that have been defined in the system for specific countries. Input tax, output tax, and non-deductible input tax are examples of tax types used in Germany.
The system determines which tax types are to be displayed by means of the country key. A calculation procedure is specified for each country key, and this procedure contains the country-specific specifications for calculating and posting the different tax types.
When you define the calculation procedure, you must answer the following questions concerning each tax type:
What is the base amount for calculating the tax? This can be the expense or revenue amount or, as with sales equalization tax in Belgium, a tax amount.
Which calculation type is used to determine the base amount: percentage included or percentage separate? With very few exceptions (such as for travel expense accounting in Germany), the base amount is normally determined percentage included.
The tax amount is 15%.
Percentage included
Tax amount = invoice gross amount * (tax rate/100 + tax rate)
150 = 1150 * ( 15 / 100 + 15)
Percentage separate
Tax amount = invoice net gross * tax rate/100
150 = 1000 * 15 / 100
To which side of the account must the tax amount be posted? The input and output tax is always posted in accordance with the G/L account and asset line items. For the tax to be posted additionally, the side of the account is determined depending on the input or output tax. For the acquisition and investment tax, for example, you post to the opposite side of the account.
Should a possible tax expense be divided between the G/L account and asset line items or posted separately? If, for example, you have a non-deductible input tax amount, you can choose whether to post to a separate expense account or apportion the tax expense between the G/L account and asset line items.
The type of tax calculation and posting depends on the answers to these questions and the combination of those answers.
The following topics introduce individual tax types and explain the necessary specifications for calculating and posting tax. For more information on the calculation procedure, see The Calculation Procedure.
See also:
Tax on Sales/Purchases: Input and Output Tax
Non-Deductible Input Tax
Deferred Tax: Italy
Sales Tax
Use Tax
Tax Calculation With or Without Jurisdiction Code?
Entering Taxes with Jurisdiction Code
Acquisition Tax
Investment Tax
Sales Equalization Tax
I hope this link will help you
http://help.sap.com/erp2005_ehp_03/helpdata/EN/e5/077e394acd11d182b90000e829fbfe/frameset.htm
Regards
Odaiah

Iphone 5 - other users recieve texts massages from me with another country code

Hello, I recently travelled to Israel and used a differnet SIM card in my Iphone, but ever since I got back to the states... othe people got my txt from my hotmail account. I read through the discussions here and figured out how to change that, the other problem is that my phone numer under the text massage setting appear with Israel country code (+972) before my american number!?
so when I go to setings>massages>send and recieve>...
my options are either my hotmail account or +972and my us number ...
so when other people recieve txts from me it seems like somebody txted them from a different country ...
anybody has an idea how to change that ?
Thank you!

Hello there, GititK.
The following Knowledge Base article offers up some great information in regards to linking phone number to iMessage:
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

If I store name's phone number with a country code eg. 218-925555555 and I receive a call as 0925555555 then only number is appeared and no name appears

if I store a name with phone number with a country code eg. +218-925555555 and I receive a call from that pearson then only number ( 0925555555 ) is appeared but no name.
and visa versa when I store 925555555 and I receive a call from that pearson then only number ( +218-925555555 ) is appeared but no name.
moreover, the same happens with messaging

cmauze2 wrote:
Ann154 wrote:
What happened to your old SIM card? You should have been able to move that card to the new replacement device.
[quoted]:
"Sales clerk asked me if I had a Sims card for it. I told him that there`s one in my old phone. He explained to me that it was not going to be working..."
Or were you referring to the one in the old temporary replacement device? Would that even be compatible with the newer phones?
The one that wasn't working had a 4G LTE SIM card in it. It should have usable in the replacement Razr. It was only until I read the OP a third time this morning that there might be a third device involved. It would be nice if people would give more specifics on what devices are active at what time. Then the readers of this community can follow the progression of the events better.

Project stock exist in a plant and WBS but with different company code

Hello,
As I know I can not create a PO in company A, but was assigned to a WBS maintained in company code B. The system will check if the WBS getting the same company code with the PO, and pop up the error message if the company code was differect.
But seems the project stock could exists in a plant but assign to WBS was maintained with different company code. For example, A material stock was in plant A assigned to company code A, and it is also assigned to WBS belong to company code B.
Any one know it is correct?
Thanks!

I knew crossing company code to assign WBS element to PO is not allowed since i got the error message, and I think it's reasonable, cause the expense from the project PO should post to the same company code through the WBS element.
But why for the inventory crossing company code is allowed? The stock in plant A belong to company code A, was assigned to WBS element B belong to company code B. That means the inventory is in the GL balance of company A but under the profit center belong to company B. How to understand it? I think it's wrong

CUCM 8.6.2 Generating CSRs With Incorrect Country Code

Hi folks, I'm running CUCM 8.6.2.25900-8 on a single cluster (1x pub, 4x sub). My CA certs for the tomcat service are due to expire shortly so I've generated CSRs for all the servers and submitted them to our provider. All but one of the requests went through with no issues but one failed because the CSR specified a country code of 'US'. We are in the UK and the four other servers all generated CSRs specifying C=GB.
Examining the current tomcat cert or issuing "show web-security" on the command-line of the server who's CSR failed also show 'C=GB'
Looking at the 'set web-security' command it appears that I cannot change the country code.
Why is the server generating CSRs with 'C=US'?
How do I change this behaviour such that they are generated with 'C=GB' instead?

Surprisingly, it has made it all the way to 10.5(x) with the same info and the same error...
I did found a method to change it via root access, and you might not require root access, but I can't tell for sure as I would need to look at exactly what the contents of the file that TAC changes, but apparently it's just the platformConfig.xml that they need to change and reboot.
If that's the case, using the utils import config using pretty much all the same info, except the country, would end up with the same outcome.
Again, not 100% sure but theory says that should do the trick, you can run that thru TAC if you open the case and see what they think about it.

EXTERNAL OPERATION in a production order with different company code plant

Hi,
in my case i am having a production order with 4 operations.
0010 milling
0020 winding
0030 cutting
0040 milling
among this opearion 0030 i want to do it in a plant which is assigned to different company code than mine.
in this case whether i should proceed with PP01 Control key with opearion plant as that plant which is lieing in diffent company code or
i should specify PP02 control key saying that plant as an external vendor for me and do PR and PO for that service .
which should i follow for my case and how cost gets updated .

Hi,
For different company code, u have to specify PP02 in the routing for external vendor. In PP02 control key indicator must be set in external opn.
Before that create purchase info record.
Enter subcontract info record in routing.
after running MRP , convert the PR to PO.
Send the material by MB1B by 541 mvt
Receive the material by MIGO by 101 mvt.
Regards,
Raja sd

MAM Order - Two items having Booking Units with Different Company Code

MAM order created with 2 Line Items
Booking Unit in each Line Item belongs to different Company Code .( Internal Order within each Booking Unit has different Co. Code )
After billing individual Line Items ,Two separate Billing doc. will be created for this Order
Each Billing document should be posted to different Co. Code depending upon Co. Code in Internal Order of respective Booking Unit
TS - 9350801900

Dear Chandramohan ,
Thanks for the reply .
But the solution given by you will just change the message class .I wanted to post Two different Line Items within a single MAM Order to different Co Codes after billing .
Scenario is that SOrg1 assigned to CCode1 & SOrg2 assigned to CCode2 .
       Booking Unit BU1 has Internal Order belonging to CCode1 & BU2 has Internal Order belonging to CCode2
Now MAM Order1 created with SOrg1 having Two Line Items with BU1 & BU2
                After Billing ,Two Billing Docs will be created for each Line Item .
                 Both Billing Doc will be posted to CCode1
Now MAM Order2 created with SOrg2 having Two Line Items with BU1 & BU2
                After Billing ,Two Billing Docs will be created for each Line Item .
                 Both Billing Doc will be posted to CCode2
Means even if Two Line Items are created within a single MAM Order having BU of different Co Codes ,after billing both Billing Docs will be posted to Co Code of Sales Org at Header level .
As per the requirement ,irrespective of header Sales org , Line Items needs to be posted to respective Co Code of Booking Units .
Tds ,
TS

Numbers with US country code (+1) are not recognized

Hi Everyone,
some of my contacts have +1 (US country code) stored in front
of their number, as that is the only way to ensure texts reach
them, while one is abroad.
In the US, though, when they call their numbers are not always
mapped to the contact by the iPhone. The incoming number is without
the +1 prefix which I guess confuses the phone.
I was wondering if other people were experiencing this and if there
is a fix for it?
Hopefully this will also reach Apple, so they can take a look at it.
Thanks for looking,
jazzy79

jazzy79 wrote:
I was wondering if other people were experiencing this and if there
is a fix for it?
Store BOTH numbers in your contact list...one with the +1, and one without. If you hit the edit button for a contact, a new field will pop up for phone numbers, add new number. You can add a custom label as well by clicking on the chevron in the "new" number field.

How to prevent settlements from AE to wbs with different company code

Hi gurus,
i'm currently facing a problem regarding settlements from activity elements to wbs above.
we have one controllign areas with various company codes.
For some projects, we have wbs assigned to company code A and activity elements assigned to Company A and B.
We have an automatic settlement rule generation so that we settle all activity element costs to wbs. But, for activity elements assigned to company B, we don't want to settle the costs, we want to go through a sd/mm invoicing between the two companies.
How can we prevent the settlement to take place, apart from manually removing the settlement rule for each activity element?
can we put a validation rule that check that whenever the company code in the wbs is different from the one in the activity element, then the settlement doesn't take place? or remove the automatic settlement rule generation and use cjb1 to generate settlement rules only when an activity element as the same company code as the wbs above. would it be possible?
would the WBS_SETTLEMENT_RULE BADI or badi proj be of any help?
Any help is welcome.
regards
tim
Edited by: Tim Ursulet on Jan 22, 2009 5:29 PM

Hi Tim,
The transaction CJB1 or CJB2 creates the settlment rules for WBS only, therefore the transactions and Badi WBS_SETTLEMENT_RULE BADI are NOT relevant for the settlement rules of activity and elements at all.
For the settlement rules of activity (and elements) the default rule is inserted, as soon as the user navigate to the settlemenent rule overview screen, if the activity do not have the settlement rule at that time. I am not sure, if there is BaDi or substituation to prevent the system apply this default rule in certain case. Other alternative is to specify the objects during settlement, e.g. using selection variant with the company code.
Kind regards,
Zhenbo

HT3529 My iPhone wont let me send text message to numbers with different area code how do I fix this?

My iPhone wont let me send text messages to numbers with a different area code. How do I fix this so I can send texts to these numbers?

If it shows up in iTunes and you can sync the phone, could be that the docking port is damaged.
You should get it serviced or looked at by visiting an Apple Store or contacting Apple:
Apple - Support - Service Answer Center

P.O. with different Tax codes for each line item.

Hi
I would like to know how the IV has been done for the P.O. with differnt tax codes for each line item. Since in MIRO at header level we can select only one tax code.

Hi
Raju,
It means we can post only one invoice at time i.e.for line item same taxcode is there.
e.g. If line item 10 has tax code A1, 20 has A2 then on header i can only select either A1 or A2 tax code & post invoice of that line item.

Xfinity TV website constantly crashing with different error codes

I am extremely fed up with this website. I constantly get 900 codes, which were fixed for a short while and now I can't load any videos with a 422 code. What is the major malfunction with this website? I never have issues streaming video on any other site but this one, and this is on every web browser. When are these issues going to be fixed? Being that, I only watch tv on the website, this makes me want to cancel Comcast.

I am extremely fed up with this website. I constantly get 900 codes, which were fixed for a short while and now I can't load any videos with a 422 code. What is the major malfunction with this website? I never have issues streaming video on any other site but this one, and this is on every web browser. When are these issues going to be fixed? Being that, I only watch tv on the website, this makes me want to cancel Comcast.

XI: Call same RFC with different language codes?

Hello all!
I have a unique situation where I need to use XI call an RFC twice, but each call will use a different language code.
I've created 2 receiver determinations and interface determinations. I've also created 2 communication channels, one for each language code, but the problem is that I cannot create a second receiver agreement to point to the second communication channel.
Anybody know how I can accomplish this?

Hi,
I would like to sugget you to use only one channel and create an extra parameter for the language on your function module. Then, you can specify the language everytime you need to call it.
regards.
roberti

PO Rejection - ORDSP Idoc Errors in ECC with different process codes

Hi All,
We were testing the Scenario where the Supplier rejects a PO line item as part of the PO Collaboration. On rejecting the PO in SNC, it trigerred an ROC XML with AcceptanceStatusCode == RE. The same was passed on from XML to Idoc in the IDoc segment E1EDP01, field ACTION = "003".
However, such ORDSP Idocs was failing on the ECC side during Inbound processing with the following errors:
1. Acknowledgment for PO item 4400000XXX 00010 contains quantity variance: Message no. ME794
2. Price unit 0 from IDoc differs from unit of purchase order 1: Message no. ME729
3. Order price unit differs from unit EA from purchase order: Message no. ME728
4. Order units differ : Message no. ME791
5. Material number differs from that of ordered material : Message no. ME790
Note : We dont get these errors for a normal confirmation. It happens only with Rejection.
The deletion indciator could not be set in the ECC PO line item even after manually correcting the above errors in the Idoc and posting it.
Then based on this SDN Post: [PO rejection in SNC does not update the items in MM with ORDRSP;, we changed the WE20 settings. i.e., for ORDSP Idoc changed the Process code from ORDR to ORDR_SUS. After this change, the the above errors were eliminated and the the rejection data was also updated on the ECC PO by setting a deletion indicator. But we are having the following issues:
1. Though both the confirmation & rejection data are getting transferred successfully, the Idocs remain in status 52 (Application document not fully posted).
2. The message in the status record is "Rejection of PO item 4400000XXX 00010 with reason: Message no. ME749
3. Came across these 2 related SAP Notes:
a. #1087422 : But this is not applicable as the note states that this error will occur only if we delete the PO line item before hand in ECC.
b. # 66192 : This note suggets a custom solution. But actually all the info from the ORDSP Idoc are getting processed successfully (Rejection & Confirmation send in the same Idoc). Only the status of the Idoc (Status = 52) is concerning us.
Looking forward for inputs / suggetions from those who have used the Rejection functionality in SNC without custom development.
Regards,
Bharath

Hi Bharath
Rejections is handled like that only, can you please check whether note 1529579 is helpful
It is standard behavior, as it expects other segments to fill, but never the less the PO will be updated properly, its only problem
with the status of the idoc....nothing wrong in the data updation. The above note should be handy.
Regards
Vinod

AP with different country code

Similar Messages

Maybe you are looking for