Automatic Master Data Maintenance in SAP Solution manager

Hello!
I am doing the settings from the "Configuration of Service Desk for VAR".
I find it difficulty "4.1 Automatic Master Data Maintenance (Standard)".
My questions:
1. Tcode SM30 -> V_AIINSNRS
http://imglink.ru/show-image.php?id=c095122ec4b0119d32ffab4675b174e7
How to insert data into a table "V_AIINSNRS"?
table V_AISAPCUSTNOS:
http://imglink.ru/show-image.php?id=f45703bd65e714ba309ecc3010fc7271
I Used report AI_SC_GET_SAP_CUSTOMER_NUMBERS.
2. I tried to run the report AI_SC_REFRESH_READ_ONLY_DATA.
http://imglink.ru/show-image.php?id=598159ed85a780096de8e5afead42095
What does this message?
Transaction SMSY_SETUP -> Expert Settings: performed
Thanks!

Hi Dmitriy,
1.
These tables are maintained by the report AI_SC_GET_SAP_CUSTOMER_NUMBERS.
Also, the report uses the S user is stored in the RFC SAP-OSS to determine all the SAP customer numbers that you support.
So, an S user from the Service Provider, with a password that has authorization to
display all customer information for the VAR customer numbers, must be available in the
RFC SAP-OSS.
For further information you can check note 1151450.
2.
To run the report AI_SC_REFRESH_READ_ONLY_DATA, you should be able to perform the above activitie first and flag customer numbers or installations for generating the data.
Best Regards,
Fernando Rocha

Similar Messages

Master Data synchronisation between two Solution Manager systems

Hi all,
does anyone know if it is possible to synchronise master data (smsy, ibase and such) between two Solution Manager systems with standard jobs?
Thanks!
Regards

I asked a likewise question on the OSS earlier and I was told
"Use MDM" (which is a separate product and must be licensed separately).
Markus

Connecting an existing CEN to the SAP Solution Manager

Hi,
I have running a CEN (Central Monitoring).
To use this Monitoring Data into the SAP Solution Manager for CPH and E2E Monitoring , a connection is needed between CEN and Solution Manager.
It seems that this information is available on SDN but I can not find it.
Has anybody experience with it?
Thanks
Paul

the extensions should be connected to the terminals on the faceplate as that enables you to connect to test socket and eliminate all your internal wiring which is essential when checking your broadband conenction. in addition the bt incoming wires on the back of the master belong to openreach. connecting to terminals A&B is star wiring and will just cause problems with any broadband conenction and should you need an openreach engineer then he would disconnect the wires and may connect to faceplate or may not connect them as that is customers responsibilty
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Maintenance Optimizer in SAP Solution Manager

what is Maintenance Optimizer in SAP Solution Manager and what are its benefits

Hi
even this may be useful
Ensure your Solution manager system is at the most recent Support Package Level, specifically ST 400 Patch 11, to reduce note application time
Download from oss most recent step-by-step setup guide
Oss note 1024932
Oss Note 1008717 ( N/A )
Relevant up to SP11 for Basis 700
OSS Note 950975 support for IE7 ( N/A we are using GUI)
Oss note 975510 corrections for snote ( Via OSS not snote )
Oss note 1004691 corrections for snote *** Corrections for 975510 ( UP TO SAP_BASIS 11 ) N/A
Common problem notes, but not critical for Maint Opt
0998987: Maintenance Optimizer: Empty error messages
1022072: Maintenance Optimizer: "No Data Available" message o See note 1025381 before applying 1022072.
1020789: Maintenance Optimizer: Allow all systems to be selected
1020802: Maintenance Optimizer List displays incomplete data
1024105: Maintenance Optimizer: two "Cancel" buttons
1025381: Maintenance Optimizer: Link to additional download files
1029453: Maintenance Optimizer - Wrong status displayed
1030405: Maintenance Optimizer: Browser opens in background
1030498: Maintenance Optimizer - IBase is not active
1032463: Maintenance Optimizer: Internet Explorer Script Error
1042704: Maintenance Optimizer: Display only employee partners
Partner Scenario SOLMAN4.0 Only
Os note 1021275 ( RFC Destinations ) N/A ST 400 11
Oss Note: 997780 ( N/A we are at 11 use note 939897 for ST400 SP11 Application )
Relevant for ST400 SP09 ( N/A ST 400 11 )
User:
To setup you must have SAP_ALL
General Users: ( Oss note 1032322 )
Must be assigned to role SAP_MAINT_OPT_ADMIN
Auth Object: D_SOL_VSBL ( visibility of solutions)
Auth Object: CRM_ORD_PR ( for CRM stuff )
/spro
As of Support Package level ST 400 SP10:
Call Transaction SPRO -> SAP Reference IMG ->SAP Solution Manager -> Advanced Configuration -> Basic Settings -> SAP Solution Manager System -> Change Management -> Set Up Maintenance Optimizer
This IMG activity refers to the SAP Note 990534: Solution Manager Maintenance Optimizer: BC Set. Follow the instructions in this SAP Note
N/A as of ST400 SP11
Define a Solution:
Solution_Manager Select Solution Overview New.
Enter Descriptive Name ( Ex. GTS Landscape )
Hit Continue
Select Solution Landscape Maintenance
Select System Groups & Logical Components on the Left hand Side
Select Solution Landscapes and pick the one you created
Define the solutions for that landscape
Highlight each item and click Logical Component (You must have a valid license to set this up)
Assign S-User
Transaction: AISUSER
Enter you user id and your SUSER ID for downloading
Create another SAPOSS Connection called SAP-OSS with S-User assigned
Call SOLUTION_MANAGER
Select Solution Overview
Select the solution you want to work with
Select Change Management Support Package Stacks
Click Maintenance Optimizer around middle of screen
Select the solution you want to get Sps for
Go to OSS and add the files to download basket
When done return to screen and hit continue
Select - Confirm files in Download Basket
Error message comes if your sap user and your oss user are not setup in AISUSER screen
Now go to SAP Download Manager ( On your local pc ) and download the files you just confirmed of course using the same S-User id you just added them to the basket with
Apply support packages via spam per normal process
Return to the SOLUTION_MANAGER window select the landscape you are working on
Hit Maintenance Optimizer List
Choose the maintenance transaction you are working on
You will see a list of the confirmed and downloaded sps you selected
Once you apply these to the system using SPAM you will change the status of implementation to Completed and Hit Save
This completes this activity
If you wish to do more work you will have to create a new transaction.
[Edit section] Add A New Instance to Maintenance Optimizer
Sign into Solution Manager
Ensure new instance has valid license installed and logical clients assigned
Select Landscape Components
Right Click Systems
 Select Create new system with assistant
Enter
SID / Description / Product Type / Installation Number ( Get this from SLICENSE in system you are setting up )
Next enter Sys # & MEssgae Server and hit continue
Next select Generate RFC Destinations & Assign Logical Components & Enter Client #
I always get a problem saving since SLD is not setup ignore and continue
Highlight the system you just added under Systems SAP Global Trade Services
Select Assignment to Logical Components
Now add additional software such as Net weaver ABAP & JAVA if your primary setup was of another type ( ex. GTS )
Highlight the system you wish to update under Systems and hit change
 Select Header Data
 Click Installed Product Versions
 In the product box add whatever you require for this system
 Select the version from the 2nd box and hit copy
Ex.
If you cannot setup the trusted system here is a workaround:
Create User in Target for Trusted System RFC from SM1
 User: <Username>
 Pass: <Pass>
 Type: Communication
Use this when setting up the trusted connection, remove the trust and use this CPIC user info for the RFC.
Generate RFCs and ensure SMSY setup is done for SID in Solution manager
Now Create a New Solution For your instance:
Go to SOLUTION_MANAGER transaction
 Select NEW
 Give Descriptive name: ex. GTS Landscape
Under Solution Landscape
 Select Solution Landscape Maintenance
 Select System Groups and Logical Components Tab
 Open Solution Landscapes
 Select the one you just defined (GTS Landscape)
SOLTION_MANAGER
Select Change Management Support Package Stacks
Select Maintenance Optimizer
Select the Product Version
 GTS 7.1
Select the System Type SID
From here you will be prompted to go to service marketplace and add the items you wish to install. You can do this beforehand as well, be sure to use the same Suser you setup in AISUSER with your sap login
It will ask you to confirm the basket, once you do that you install them normally.
Download with sap download manager, ftp and apply

How to Transfer Customizing Data from SAP ECC6 to SAP Solution Manager

Hi all,
I want to Transfer Customizing Data (such as organization structure) from SAP ECC6 to SAP Solution Manager.Please tell me how. Thanks.

Hi,
The system cannot capture the customizing data from your ECC6. This is another myth with SAP Solution Manager. Solution Manager can only smoothen the process of your Project Management.
Hope this solves your problem.
Feel free to revert back.
--Ragu

Questions on "FAQ - SAP Solution Manager for VARs"

Hi,
I just got through the FAQ - SAP Solution Manager for VARs, but have some further questions:
For me it is not quite clear which connections are necessary for which VAR scenrio.. currently we have setup the service desk in our solman. Customer's aren't linked to the solman yet - we have saprouter-saprouter connections. Connecting them via SAP support backbone is an interesting option, especially for incident management. To get this working we should follow note 1124718 right?
But what about the other scenarios like maintenance optimizer and ewa monitoring? I guess for that we definitly need to build up RFC connections to each relevant customer system (~300+x)?! I think it will be hard to handle so many connections - just consider if a customer is cancalling the maintenance contract, everything needs to be removed again... best would be to have a central communication point...
For MOPZ we need up-to-date system information. So everyone is talking about SLD. Do you also recommend this option? There we need again a connection (direct to SolMan SLD or via external SLD on customer side).
According to the FAQ there is a workaround for ewa monitoring for customers with security doubts.. is this also working for non-ABAP components? We need SMD and WI for generating ewas for JAVA systems...
With regards to Enterprise Support contract: ewa only need to be monitored for productive systems? Can a customer be charged if they want to have ewas monitored for other sytems too? How long do we need to keep the ewas (1 month, 3 months, half year) before they are deleted? Are there any specific requirements?
All the work to get these scenarios working.. is this covered within the Enterprise Support contract? Can the customer be charged for work thats done by the VAR in their system (e.g. RFC connections, SDCCN, SLD,...)?
Sorry for this long text.. hope you have some helpful ideas!
Regards,
Richard

Hello Richard,
(1) regarding network connections see document [Draft:Technical Support Network Connections for VAR Scenario|http://service.sap.com/~form/sapnet?_SHORTKEY=00200797470000089947&_OBJECT=011000358700000880802009E] as overview and with a lot of detailed information.
(2) yes, you have to setup once all your customer connections at the beginning but then only add/remove with customer contract changes
(3) the workaround by sending by email can handled a anexception. EWA has to be done for productive systems like nowadays done by SAP. Additional EWA services could meas additional business case for a VAR - that's contract between VAR and customer.
(4) whatever you think may be a business to sell - do it ! (and get a monetary bonus from your boss
Kind regards
Heinrich

Error with Maintenance Optimizer in Solution Manager 4.0

Hi, I am configuring Solution Manager for download SP, I check marketplace and download the guide, when I try to download a SP following message show me:
"Change requests cannot be displayed or created, because the RFC connection has errors, or is not maintained.
Check whether the RFC connection to the Change Man agement system is under the key CHARM_DEST (APPLI field in the DESTINAT field), in the view BCOS_CUST. You need authorization for the cross-client view/table maintenance (S_TABU_DIS and S_TABU_CLI).
Check the RFC connection in the transaction SM59. If your SAP Solution Manager system is also your Change Manager system, the internal connection must be 'NONE'. You need authorization for the administration of RFC connections (S_RFC_ADM)."
I go to sm59, verify RFC SAP-OSS with correct data, I found at guide following Host :
/H/54.16.44.50/S/sapdp99/H/54.62.200.35/S/
When I try press Connection Test Buttom I can not connect to SAP.
Do you know which can be my error? .....
Regards.

Hi,
Following the note 1024932
Steps to do before configre the maintance optimizer you need to configure sattilite systems in solution manager.
go to SMSY and configre R\3 systems.For these systems you need to create RFC connections and Logical comp.
http://service.sap.com/rkt-solman
for tutors and PDFs how to set up MOPZ.
Points if it helpfull
Regards
Neni

Default User Parameters in SAP SOLUTION MANAGER 7.1

Hi,
I want some default parameters automatically be assigned to new users when they are created instead of manually adding every time in su01 transaction code. Do you know how to configure this?
SAP SOLUTION MANAGER 7.1
SAP_BASIS
702
0012
SAPKB70212
SAP Basis Component
I try settings in SSM_CUST for user-exit Z_USERS_TRANSFER and SAP_USERS_TRANSFER, but it's don't work.
Thank you.

Code function module runs in SAP EHP 1 for SAP Solution Manager 7.0 SAP_BASIS 701.
In SAP SOLUTION MANAGER 7.1 SAP_BASIS 702 function module is ignored. it can be seen if you set a breakpoint in the function module.
FUNCTION CREATE_USER_HR_INFO.
*"*"Локальный интерфейс:
DATA: su01_mode(5) type c.
field-symbols: <BNAME> like USR02-BNAME.
field-symbols: <ACCNT> like BAPILOGOND-ACCNT.
field-symbols: <CLASS> like USLOGOND-CLASS.
field-symbols: <FUNCTION> like ADDR3_DATA-FUNCTION.
field-symbols: <DEPARTMENT> like ADDR3_DATA-DEPARTMENT.
field-symbols: <su01_mode> like su01_mode.
DATA hr_rfc TYPE STANDARD TABLE OF ZSTR_HR_PERSON_INFO WITH HEADER LINE. " инф-ция о польз-лях, получаемая из HR по RFC
DATA : sys_msg(80) TYPE c,
 indx TYPE i.
DATA ADDRESS LIKE TABLE OF BAPIADDR3 WITH HEADER LINE.
DATA ADDRESSX LIKE TABLE OF BAPIADDR3X WITH HEADER LINE.
DATA DEFAULTS LIKE TABLE OF BAPIDEFAUL WITH HEADER LINE.
DATA DEFAULTSX LIKE TABLE OF BAPIDEFAX WITH HEADER LINE.
DATA LOGONDATA LIKE STANDARD TABLE OF BAPILOGOND WITH HEADER LINE.
DATA LOGONDATAX LIKE STANDARD TABLE OF BAPILOGONX WITH HEADER LINE.
DATA RETURN LIKE STANDARD TABLE OF BAPIRET2.
DATA res_lines TYPE i VALUE 0.
assign ('(SAPLSUU5)g_ok_start') to <su01_mode>.
if sy-subrc = 4.
 exit.
ENDIF.
*<su01_mode> will have the following values: create = "CREA", change = "CHAN", and delete = "DELE"
* DATA mes TYPE string.
* mes = sy-subrc.
* CONCATENATE 'sy-subrc' mes into mes separated by SPACE .
* MESSAGE mes TYPE 'I'.
if <su01_mode> = 'CREA'.
 assign ('(SAPLSUU5)USLOGOND-ACCNT') to <ACCNT>.
 assign ('(SAPLSUU5)USR02-BNAME') to <BNAME>.
 assign ('(SAPLSUU5)USLOGOND-CLASS') to <CLASS>.
 assign ('(SAPLSUU5)ADDR3_DATA-FUNCTION') to <FUNCTION>.
 assign ('(SAPLSUU5)ADDR3_DATA-DEPARTMENT') to <DEPARTMENT>.
 hr_rfc-PERNR = <ACCNT>.
 APPEND hr_rfc.
 CALL FUNCTION 'GET_HR_PERSON_INFO' DESTINATION 'PHRCLNT200_HR'
 TABLES
 PERSON_INFO = hr_rfc
 EXCEPTIONS
 SYSTEM_FAILURE = 1 MESSAGE sys_msg
 COMMUNICATION_FAILURE = 2 MESSAGE sys_msg
DESCRIBE TABLE hr_rfc LINES res_lines.
*если по табельному номеру нашлись данные - заполняю ими структуры
if res_lines > 0.
 LOOP at hr_rfc.
 DEFAULTS-KOSTL = hr_rfc-PLANS.
 DEFAULTSX-KOSTL = 'X'.
 if hr_rfc-GESCH = '1'.
 ADDRESS-TITLE_P = 'Господин'.
 else.
 ADDRESS-TITLE_P = 'Госпожа'.
 ENDIF.
 SPLIT hr_rfc-ENAME AT space
 INTO ADDRESS-LASTNAME
 ADDRESS-FIRSTNAME
 ADDRESS-MIDDLENAME.
 if <FUNCTION> = ''.
 ADDRESS-FUNCTION = hr_rfc-FUNCTION.
 ELSE.
 ADDRESS-FUNCTION = <FUNCTION>.
 ENDIF.
 if <DEPARTMENT> = ''.
 ADDRESS-DEPARTMENT = hr_rfc-STEXT.
 ELSE.
 ADDRESS-DEPARTMENT = <DEPARTMENT>.
 ENDIF.
 ADDRESSX-TITLE_P = 'X'.
 ADDRESSX-LASTNAME = 'X'.
 ADDRESSX-FIRSTNAME = 'X'.
 ADDRESSX-MIDDLENAME = 'X'.
 ADDRESSX-FUNCTION = 'X'.
 ADDRESSX-DEPARTMENT = 'X'.
 ENDLOOP.
endif.
 DEFAULTS-LANGU = 8.
 DEFAULTS-DCPFM = 'Y'.
 DEFAULTS-SPLD = 'LOCL'.
 DEFAULTS-SPDB = 'G'.
 DEFAULTS-SPDA = 'D'.
 APPEND DEFAULTS to DEFAULTS.
 DEFAULTSX-LANGU = 'X'.
 DEFAULTSX-DCPFM = 'X'.
 DEFAULTSX-SPLD = 'X'.
 DEFAULTSX-SPDB = 'X'.
 DEFAULTSX-SPDA = 'X'.
 APPEND DEFAULTSX.
 ADDRESS-NAMEFORMAT = '03'.
 ADDRESS-NAMCOUNTRY = 'UA'.
 APPEND ADDRESS to ADDRESS.
 ADDRESSX-NAMEFORMAT = 'X'.
 ADDRESSX-NAMCOUNTRY = 'X'.
 APPEND ADDRESSX.
 LOGONDATA-GLTGV = sy-datum.
 LOGONDATA-GLTGB = '99991231'.
 LOGONDATA-TZONE = 'EET'.
 if <CLASS> = ''.
 LOGONDATA-CLASS = 'END_USER'.
 ELSE.
 LOGONDATA-CLASS = <CLASS>.
 ENDIF.
 APPEND LOGONDATA.
 LOGONDATAX-GLTGV = 'X'.
 LOGONDATAX-GLTGB = 'X'.
 LOGONDATAX-CLASS = 'X'.
 LOGONDATAX-TZONE = 'X'.
 APPEND LOGONDATAX.
 CALL FUNCTION 'BAPI_USER_CHANGE'
 EXPORTING
 USERNAME = <BNAME>
 ADDRESS = ADDRESS
 ADDRESSX = ADDRESSX
 DEFAULTS = DEFAULTS
 DEFAULTSX = DEFAULTSX
 LOGONDATA = LOGONDATA
 LOGONDATAX = LOGONDATAX
 TABLES
 RETURN = RETURN
* DATA mes TYPE string.
* mes = sy-subrc.
* CONCATENATE 'sy-subrc' mes into mes separated by SPACE .
* MESSAGE mes TYPE 'I'.
ENDIF.
*ENDIF.
ENDFUNCTION.

SAP Solution Manager - Enterprise Support Report bw cubes

We are looking at the Infoproviders in Solution Manager BW and noticed the data for SAP Solution Manager - Enterprise Support Report.
When we look at these cubes, we are particularly interested in the Software Component Versions.
Unfortunately, all of these data cubes are empty. Based on some discussions among our colleagues we are wondering if this data is only activated for customers that have the full Enterprise Support agreement in place with SAP?
If that is the case, then so be it (we don't have that level of support). However, if that is not the case, can anyone suggest a way to populate these cubes.
thanks,
Jeff Henke

Hi,
Solution Manager is a separate component and needs to be installed separately (not possible to install on top of R/3 Enterprise).
You can order SAP Solution Manager Software from SAP or download from http://service.sap.com/swdc
Solution manager is free from SAP and no additional license involved for it's customer for normal use.
You can get more information on Solution manager from http://service.sap.com/solutionmanager
btw: as far as I know for R/3 Enterprise you can still download patches via http://service.sap.com/swdc without solution manager, For Netweaver 7.0 systems, use of Solution Manager (Maintenance Optimizer) became mandatory.
Cheers !!
Satya.
PS: Pls reward points if the answer was helpful...Thx.

Upload of Test Cases in SAP Solution Manager.

Hello,
I am trying to create a project and its component in SAP Solution Manager with 12 Test Plans. The Test Plans have different number of test cases. I do not have the Test cases now, but I shall have them in future. I currently have the following data.
Test Plan ID
Module
Business Process
Business Area
Sub Business Area
Test Case Description
Test Case Details
Transaction Codes
Priority of Test Cases
Can I create a structure of a project in the development system in which I have 12 Test Plans and n number of Test Cases under every Test Plan? The structure would have place holder for each test case in which I can upload the Test Cases later. Is that possible?
Regards,
Namrata.

Hi Namrata,
Yes, you can create project structure before using solar01 tcode. later once your test cases (either manual or automatic) are ready then you can upload them using solar02 on test cases tab,
refer Link Test Case to Transactions/Reports - Configuration - SAP Library
Assignments - SAP Solution Manager - SAP Library
Thanks
Jansi

Upgrade button missing in maintenance optimizer of Solution manager

Hi,
We are going to perform upgrade R/3 4.7*110 Non uniocde to ERP 6.0 EHP non unicode.
We used SAP EHP 1 for SAP Solution Manager 7.0 and support packake for SAP EHP 1 for SAP Solution Manager 7.0 is 24.
Applied following OSS notes pertaining to MOPZ :
0001450757
0001461849
0001485385
0001548530
0001590226
COnfigured using tx code SMSY - Product System is SAP ERP and product version is SAP ERP 2004.
Created logical components and assigned to <SID> of R/3 4.7 Development system.
Then created solution and configured solution landscape . Logical component was assigned to solution landscape.
Then clicked on "Create new Optimizer transaction"
Then select product version : ERP 2004
Then select Product system and selected <SID>.
But only "maintenance" button was displayed.
However "Upgrade with enhancement package" button is not showing.
Please help us the solution.
Thanks
ap

A Prasad Rao wrote:
Hi Sunny
> For R/3 4.7*110 product name is ERP and product version is ERP 2004
>
> I want upgrade button or upgrade with Enhancement package button should appear
>
> It seems we need to apply some OSS notes but coul not find anything becasue SP stack for solman installed was 24.
>
> Please help
> Thanks and Regards
> APR
As I said earlier, you need to register it as ERP 6.0 only to get Enhancement Package installation button. There is no other option for it. If you want to confirm then check How to install EHP4 guide on http://service.sap.com/erp-ehp.
Thanks
Sunny

Error in installation of Sap Solution Manager - AIX / Oracle

Hello,
We are installing SAP Solution Manager in Operating System is AIX 5.3 and Database System is Oracle 10.2
After the Oracle Installation, in the phase of Abap Import (16 of 44), we are
receiving the follow error message:
Required system resources are missing or not available:
Import directory '/oracle/install/51032524/EXP1' does not exist;
Import directory '/oracle/install/51032524/EXP2' does not exist;
Import directory '/oracle/install/51032524/EXP3' does not exist;
Import directory '/oracle/install/51032524/EXP4' does not exist.
ERROR 2007-04-12 15:27:41
CJS-30022 Program 'Migration Monitor' exits with error code 2. For
details see log file(s) import_monitor.java.log, import_monitor.log.

The installation export DVD was copied to local machine (the directory
list is attached in zip file). We get this DVD from
service.sap.com/swdc.
java version "1.4.2"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2)
Classic VM (build 1.4.2, J2RE 1.4.2 IBM AIX 5L for PowerPC (64 bit JVM) build caix64142ifx-20061222 (ifix 113727: SR7 + 112603) (JIT enabled: jitc))
IMPORT_MONITOR.JAVA shows this message:
java version "1.4.2"
Java(TM) 2 Runtime Environment, Standard Edition (build 2.3)
IBM J9 VM (build 2.3, J2RE 1.4.2 IBM J9 2.3 AIX ppc64-64 j9ap64142ifx-20061222 (JIT enabled)
J9VM - 20061220_10521_BHdSMr
JIT - 20061026_1805_r8
GC - 200612_20)
Required system resources are missing or not available:
Import directory '/oracle/install/51032524/EXP1' does not exist;
Import directory '/oracle/install/51032524/EXP2' does not exist;
Import directory '/oracle/install/51032524/EXP3' does not exist;
Import directory '/oracle/install/51032524/EXP4' does not exist.
And the directory is OK
/oracle/install/51032524
ls -l
total 160
-rwxrwxrwx 1 root system 79 Apr 12 09:54 CDLABEL.ASC
-rwxrwxrwx 1 root system 79 Apr 12 09:54 CDLABEL.EBC
-rwxrwxrwx 1 root system 9093 Apr 12 09:54 COPY_TM.HTM
-rwxrwxrwx 1 root system 5787 Apr 12 09:54 COPY_TM.TXT
-rwxrwxrwx 1 root system 8559 Apr 12 09:54 CRCFILE.DAT
drwxrwxrwx 4 root system 256 Apr 12 10:03 EXP1
drwxrwxrwx 4 root system 256 Apr 12 10:11 EXP2
drwxrwxrwx 4 root system 256 Apr 12 10:14 EXP3
drwxrwxrwx 4 root system 256 Apr 12 10:16 EXP4
-rwxrwxrwx 1 root system 88 Apr 12 09:54 LABEL.ASC
-rwxrwxrwx 1 root system 88 Apr 12 09:54 LABEL.EBC
-rwxrwxrwx 1 root system 20 Apr 12 09:54 LABELIDX.ASC
-rwxrwxrwx 1 root system 22361 Apr 12 09:54 SHAFILE.DAT
-rwxrwxrwx 1 root system 22 Apr 12 09:54 VERSION.ASC
Please, anybody have any idea?
Thanks for help,
Carlos Nogueira

Hi Carlos, can you resolve this ? because i have the same problem, but with sql and win 2003.
java version "1.4.2_15"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_15-b02)
Java HotSpot(TM) Client VM (build 1.4.2_15-b02, mixed mode)
Required system resources are missing or not available:
Import directory sapinst\saptrans\D51032007\EXP1' does not exist;
Import directory 'sapinst\saptrans\D51032007\EXP2' does not exist;
Import directory 'sapinst\saptrans\D51032007\EXP3' does not exist;
Import directory 'sapinst\saptrans\D51032007\EXP4' does not exist.
thanks in avance.

Error in Import Java Dump phase while installing SAP solution Manager 7.1

Hi,
While installing SAP solution manager 7.1 I am getting the below error during the phase "Import Java Dump".
An error occurred while processing option SAP Solution Manager 7.1 > SAP Systems > MS SQL Server > Central System > Central System( Last error reported by the step : Execution of JLoad tool 'C:\j2sdk1.4.2_17-x64\bin\java.exe -classpath "C:\Program Files\sapinst_instdir\SOLMAN71\SYSTEM\MSS\CENTRAL\AS\install\sharedlib\launcher.jar" -showversion -Xmx1024m com.sap.engine.offline.OfflineToolStart com.sap.inst.jload.Jload "C:/Program Files/sapinst_instdir/SOLMAN71/SYSTEM/MSS/CENTRAL/AS/install/lib/iaik_jce.jar;C:/Program Files/sapinst_instdir/SOLMAN71/SYSTEM/MSS/CENTRAL/AS/install/sharedlib;D:/usr/sap/SPT/SYS/exe/uc/NTAMD64/mssjdbc/sqljdbc.jar" -sec SPT,jdbc/pool/SPT,
smn/sapmnt/SPT/SYS/global/security/data/SecStore.properties,
smn/sapmnt/SPT/SYS/global/security/data/SecStore.key -dataDir "D:/SAP SOLMAN/Java Components/51040039\DATA_UNITS\SOLMAN_JAVA_EXPORT_JDMP" -job "C:\Program Files\sapinst_instdir\SOLMAN71\SYSTEM\MSS\CENTRAL\AS\IMPORT.XML" -log jload.log' aborts with return code 1. SOLUTION: Check 'jload.log' and 'C:/Program Files/sapinst_instdir/SOLMAN71/SYSTEM/MSS/CENTRAL/AS/jload.java.log' for more information.
JLOAD.JAVA log details below
java version "1.4.2_17"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_17-b06)
Java HotSpot(TM) 64-Bit Server VM (build 1.4.2_17-b06, mixed mode)
Jload R 7.12 V 0 A 0
Jload -sec SPT,jdbc/pool/SPT,
smn/sapmnt/SPT/SYS/global/security/data/SecStore.properties,
smn/sapmnt/SPT/SYS/global/security/data/SecStore.key -dataDir D:/SAP SOLMAN/Java Components/51040039\DATA_UNITS\SOLMAN_JAVA_EXPORT_JDMP -job C:\Program Files\sapinst_instdir\SOLMAN71\SYSTEM\MSS\CENTRAL\AS\IMPORT.XML -log jload.log
Connecting to database
Couldn't connect to DB
com.sap.inst.common.exception.DBConnectionException: com.microsoft.sqlserver.jdbc.SQLServerException: The TCP/IP connection to the host has failed. java.net.ConnectException: Connection refused: connect
     at com.sap.inst.common.db.DBConnection.connect(DBConnection.java:157)
     at com.sap.inst.jload.Jload.main(Jload.java:222)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:324)
     at com.sap.engine.offline.OfflineToolStart.main(OfflineToolStart.java:81)
Caused by: com.microsoft.sqlserver.jdbc.SQLServerException: The TCP/IP connection to the host has failed. java.net.ConnectException: Connection refused: connect
     at com.microsoft.sqlserver.jdbc.SQLServerException.makeFromDriverError(Unknown Source)
     at com.microsoft.sqlserver.jdbc.SQLServerConnection.connectHelper(Unknown Source)
     at com.microsoft.sqlserver.jdbc.SQLServerConnection.loginWithoutFailover(Unknown Source)
     at com.microsoft.sqlserver.jdbc.SQLServerConnection.connect(Unknown Source)
     at com.microsoft.sqlserver.jdbc.SQLServerDriver.connect(Unknown Source)
     at com.sap.sql.jdbc.NativeConnectionFactory.createNativeConnection(NativeConnectionFactory.java:215)
     at com.sap.sql.connect.OpenSQLDataSourceImpl.createConnection(OpenSQLDataSourceImpl.java:522)
     at com.sap.sql.connect.OpenSQLDataSourceImpl.getConnection(OpenSQLDataSourceImpl.java:276)
     at com.sap.inst.common.db.DBConnection.connectViaSecureStore(DBConnection.java:111)
     at com.sap.inst.common.db.DBConnection.connect(DBConnection.java:151)
     ... 6 more
An error occured during execution. Please consult SAP note 942766 for first steps on troubleshooting the problem.
I have gone thru with the notes and it didn't help me much.
I have used J2SDK 1.4.2_17 nad JCE_Policy-1.4.2 files.
Please let me know where IO went wrong.
Thanks in advance.
Sai

Hi,
1. Did you select java path (Export CD/DVD) while intsallation? Check once again.
2. Add JAVA_HOME = Java path in environment variable.
3. What is the exact error, you got it, post error here.
Regards,
Srini Nookala

SAP Solution Manager 4.0 Install on iSeries V5R4M0 fails on STEP 40 of 40

During Step 40 of 40 of Solution Manager 4.0 install on iSeries running i5/OS V5R3M0 failed with the following error:
ERROR 2006-08-18 10:00:57 [iaxxgenimp.cpp:728]
showDialog()
FCO-00011 The step fixTemplate400 with step key
|NW_Onehost|ind|ind|ind|ind|0|0|SAP_Software_Features_Configuration|ind|ind|ind|ind|5|0|NW_Call_Offline_CTC|ind|ind|ind|ind|7|0|fixTemplate400
was executed with status ERROR .
TRACE [iaxxgenimp.cpp:657]
showDialog()
<html><head></head><body>An error occurred while processing service
SAP Solution Manager 4.0 > SAP Systems > IBM DB2 UDB for i
TRACE [iaxxgenimp.cpp:1093]
showDialog()
waiting for an answer from gui
***********End of Data*******************
Searching OSS Notes, there is no reference to the FCO-00011 error code

Hello Loli,
I think it was me, who misunderstood.
Now I followed your recommendations, increased virtual memory on the sapinst machine, restarted the pc and the installation and it completed successfully. Thank you very much.
Sorry that I can't give you points for the helpfull answer, because this is not my thread.
Kind regards,
Jürgen Scheckelhoff.

How to configuration Maintenance Optimizer in Solution Manager 4.0?

Hi All,
Can any tell me How to configuration Maintenance Optimizer in Solution Manager 4.0?
If any one having the document for same then please give me.
My mail id is : - <email address removed by moderator>
Thanks a lot,
Harshal

Hello Harshal,
Please go to service.sap.com/solutionmanager, click on the "maintenance optimizer" link, then a step-by-step guide is available there.
Another document is attached in Note 990534.
If you have further issues, Note 1024932 might be a good starting point.
Best regards,
Victor

Automatic Master Data Maintenance in SAP Solution manager

Similar Messages

Maybe you are looking for