BBSM fails to locate client
i have a bbsm server I'm bringing up on line. Trying to add the first site, i configured everything i think right, but the client gets a network error page, and the event log shows:
EventID:28
Source:BBSM_AtNotify
Description:
Failed to locate client ip:10.233.1.10 MAC: 00 00 00 00 00 db on any network device.
i did a debug on the AP1200 (12.3(4)JA) i am using and see that the bbsm is talking to the bbsm. I just can't figure out what i am doing wrong.
Debug from AP:
Apr 26 21:30:25.694: SNMP: Packet received via UDP from 10.230.0.2 on BVI1
Apr 26 21:30:25.695: SNMP: Get request, reqid 2739, errstat 0, erridx 0
dot1dTpFdbEntry.2.0.12.65.249.73.219 = NULL TYPE/VALUE
Apr 26 21:30:25.697: SNMP: Response, reqid 2739, errstat 2, erridx 1
dot1dTpFdbEntry.2.0.12.65.249.73.219 = NULL TYPE/VALUE
Apr 26 21:30:25.699: SNMP: Packet sent via UDP to 10.230.0.2
There are many reason for this kind of errors.check some listed below
http://www.cisco.com/en/US/products/sw/netmgtsw/ps533/products_user_guide_chapter09186a008019228b.html#1045412
Similar Messages
-
ASA 5505 initial build - Failed to locate egress interface (Please help :-) )
Hi, I have just purchased a ASA 5505 and have completed the initial setup via the wizard. I am currently unable to access services on the outside of the ASA.
The error: 'Failed to locate egress interface for UDP from inside'.... appears when ever my DNS server attempts a lookup.
I have configured this several times from scratch using the wizard and I am unable to figure out the issue with the NAT / Routing config.
If I run the packet tracer I get the error: "(no-route) no route to host", however I do have a default route configured so I suspect it maybe my NAT configuration.
Overview, 192.168.10.0/24 inside the ASA, 192.168.1.0/24 outside the ASA, 192.168.1.1 is the gateway to the internet. I ideally want the ASA to use PAT to mask the 192.168.10.0/24 network behind the ASAs 192.168.1.0/24 network address but still allow clients to gain internet access.
Full config follows, screen shots attached, any help would be very gratefully received.
Result of the command: "sh run"
: Saved
ASA Version 9.0(1)
hostname firewall
enable password (REMOVED) encrypted
passwd (REMOVED) encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 192.168.1.254 255.255.255.0
interface Vlan5
no nameif
security-level 50
ip address dhcp
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server1
host 192.168.10.10
object network GoogleDNS1
host 8.8.8.8
description Google DNS Server
object network GoogleDNS2
host 8.8.4.4
description Google DNS Server
object network 192.168.10.x
subnet 192.168.10.0 255.255.255.0
object network InternetRouter
host 192.168.1.1
object-group network DM_INLINE_NETWORK_1
network-object object GoogleDNS1
network-object object GoogleDNS2
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
access-list inside_access_in remark External DNS Lookups
access-list inside_access_in extended permit udp object Server1 object-group DM_INLINE_NETWORK_1 eq domain
access-list inside_access_in extended permit tcp 192.168.10.0 255.255.255.0 any object-group DM_INLINE_TCP_1
access-list inside_access_in extended deny ip any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source dynamic any interface
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 255.255.255.255 192.168.1.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
ssh version 2
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:(REMOVED)
: endJust to want to be sure, can you post output from show int ip brie and show route? And try to remove your ACL for testing purpose or at least don't applied it anywhere yet.
Once done, try do another packet-tracer to 8.8.8.8 using icmp packet instead of UDP paste the whole the output here. Before doing this, add icmp any any outside command on the ASA.
I know this should have anything to do with your issue, because if ACL is the issue then you will see output being denied by ACL on the packet tracer output. Let us know the results. -
Failed To install Client - 2012 SCCM - Following is the Logs
Hi Support .... Below is the log which, i am getting. while i am trying deploy or install client on machines ....plz help me out
<![LOG[Sending message body '<ContentLocationRequest SchemaVersion="1.00">
<AssignedSite SiteCode="ADC"/>
<ClientPackage/>
<ClientLocationInfo LocationType="SMSPACKAGE" DistributeOnDemand="0" UseProtected="0" AllowCaching="0" BranchDPFlags="0" AllowHTTP="1" AllowSMB="0" AllowMulticast="0"
UseInternetDP="0">
<ADSite Name="Default-First-Site-Name"/>
<Forest Name="wesee.org"/>
<Domain Name="wesee.org"/>
<IPAddresses>
<IPAddress SubnetAddress="131.107.2.0" Address="131.107.2.130"/>
<IPAddress SubnetAddress="2002:836B:0282:0000" Address="2002:836B:0282:0000:0000:0000:836B:0282"/>
</IPAddresses>
</ClientLocationInfo>
</ContentLocationRequest>
']LOG]!><time="09:46:42.900-330" date="02-09-2015" component="ccmsetup" context="" type="0" thread="4620" file="siteinfo.cpp:96">
<![LOG[Sending message header '<Msg SchemaVersion="1.1"><ID>{E34B2C49-F83D-4976-B65F-694D9BF0AFCD}</ID><SourceHost>WIN-12-ADC</SourceHost><TargetAddress>mp:[http]MP_LocationManager</TargetAddress><ReplyTo>direct:WIN-12-ADC:LS_ReplyLocations</ReplyTo><Priority>3</Priority><Timeout>600</Timeout><ReqVersion>5931</ReqVersion><TargetHost>http://WIN-12-ADC.wesee.org</TargetHost><TargetEndpoint>MP_LocationManager</TargetEndpoint><ReplyMode>Sync</ReplyMode><Protocol>http</Protocol><SentTime>2015-02-09T04:16:42Z</SentTime><Body
Type="ByteRange" Offset="0" Length="1316"/><Hooks><Hook3 Name="zlib-compress"/></Hooks><Payload Type="inline"/></Msg>']LOG]!><time="09:46:42.900-330" date="02-09-2015"
component="ccmsetup" context="" type="0" thread="4620" file="siteinfo.cpp:177">
<![LOG[CCM_POST 'http://WIN-12-ADC.wesee.org/ccm_system/request']LOG]!><time="09:46:42.951-330" date="02-09-2015" component="ccmsetup" context="" type="1" thread="4620" file="httphelper.cpp:807">
<![LOG[Failed to receive ccm message response. Status code = 404]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context="" type="2" thread="4620" file="httphelper.cpp:1694">
<![LOG[GetDPLocations failed with error 0x80004005]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context="" type="3" thread="4620" file="siteinfo.cpp:532">
<![LOG[Failed to get DP locations as the expected version from MP 'http://WIN-12-ADC.wesee.org'. Error 0x80004005]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context="" type="2"
thread="4620" file="ccmsetup.cpp:11261">
<![LOG[Failed to find DP locations from MP 'http://WIN-12-ADC.wesee.org' with error 0x80004005, status code 404. Check next MP.]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context=""
type="2" thread="4620" file="ccmsetup.cpp:11117">
<![LOG[Only one MP http://WIN-12-ADC.wesee.org is specified. Use it.]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context="" type="1" thread="4620" file="ccmsetup.cpp:10080">
<![LOG[Have already tried all MPs. Couldn't find DP locations.]LOG]!><time="09:46:42.956-330" date="02-09-2015" component="ccmsetup" context="" type="3" thread="4620" file="ccmsetup.cpp:11146">
<![LOG[GET 'http://WIN-12-ADC.wesee.org/CCM_Client/ccmsetup.cab']LOG]!><time="09:46:43.055-330" date="02-09-2015" component="ccmsetup" context="" type="1" thread="4620" file="httphelper.cpp:807">
<![LOG[Failed to successfully complete WinHttp request. (StatusCode at WinHttpQueryHeaders: 404)]LOG]!><time="09:46:43.058-330" date="02-09-2015" component="ccmsetup" context="" type="3" thread="4620"
file="httphelper.cpp:1013">
<![LOG[DownloadFileByWinHTTP failed with error 0x80004005]LOG]!><time="09:46:43.058-330" date="02-09-2015" component="ccmsetup" context="" type="3" thread="4620" file="httphelper.cpp:1081">
<![LOG[Sending Fallback Status Point message to 'WIN-12-ADC.wesee.org', STATEID='308'.]LOG]!><time="09:46:43.058-330" date="02-09-2015" component="ccmsetup" context="" type="1" thread="4620"
file="ccmsetup.cpp:9756">
<![LOG[Failed to get client version for sending messages to FSP. Error 0x80041010]LOG]!><time="09:46:43.062-330" date="02-09-2015" component="ccmsetup" context="" type="2" thread="4620" file="ccmsetup.cpp:9838">
<![LOG[Params to send FSP message '5.0.7958.1000 Deployment Error 0x80004005. Url http://WIN-12-ADC.wesee.org/CCM_Client/ccmsetup.cab']LOG]!><time="09:46:43.062-330" date="02-09-2015" component="ccmsetup" context=""
type="0" thread="4620" file="ccmsetup.cpp:9887">
<![LOG[State message with TopicType 800 and TopicId {D5B33142-10A3-403C-A2F9-84E7F9F977E5} has been sent to the FSP]LOG]!><time="09:46:43.078-330" date="02-09-2015" component="FSPStateMessage" context="" type="1"
thread="4620" file="fsputillib.cpp:752">
<![LOG[CcmSetup failed with error code 0x80004005]LOG]!><time="09:46:43.109-330" date="02-09-2015" component="ccmsetup" context="" type="1" thread="4620" file="ccmsetup.cpp:10879">This is *not* support. It is a community based forum to provide best effort help. If you want "support" please contact Microsoft Customer Support Services (CSS) or your service provider.
Based upon the log file above, your Management Point is not healthy. Each and every request to the MP is met with an http error code of 404 which indicates "Not Found". Please review your MP's health.
Jason | http://blog.configmgrftw.com | @jasonsandys -
Routing failed to locate next hop for ICMP from outside:10.60.30.111/1 to inside:10.89.30.41/0
ASA 5505 Split tunneling stopped working when upgraded from 8.3(1) to 8.4(3).
When a user was connecting to the old 8.3(1) appliance they could access all of our subnets: 10.60.0.0/16, 10.89.0.0/16, 10.33.0.0/16, 10.1.0.0/16
but now they cannot and in the logs I can just see
6 Oct 31 2012 08:17:59 110003 10.60.30.111 1 10.89.30.41 0 Routing failed to locate next hop for ICMP from outside:10.60.30.111/1 to inside:10.89.30.41/0
any hints? i have tried almost everything. the running configuration is:
: Saved
ASA Version 8.4(3)
hostname asa
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.60.70.1 255.255.0.0
interface Vlan2
nameif outside
security-level 0
ip address 80.90.98.217 255.255.255.248
ftp mode passive
clock timezone GMT 0
dns domain-lookup inside
dns domain-lookup outside
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_10.33.0.0_16
subnet 10.33.0.0 255.255.0.0
object network NETWORK_OBJ_10.60.0.0_16
subnet 10.60.0.0 255.255.0.0
object network NETWORK_OBJ_10.89.0.0_16
subnet 10.89.0.0 255.255.0.0
object network NETWORK_OBJ_10.1.0.0_16
subnet 10.1.0.0 255.255.0.0
object network tetPC
host 10.60.10.1
description test
object network NETWORK_OBJ_10.60.30.0_24
subnet 10.60.30.0 255.255.255.0
object network NETWORK_OBJ_10.60.30.64_26
subnet 10.60.30.64 255.255.255.192
object network SSH-server
host 10.60.20.6
object network SSH_public
object network ftp_public
host 80.90.98.218
object network rdp
host 10.60.10.4
object network ftp_server
host 10.60.20.2
object network ssh_public
host 80.90.98.218
object service FTP
service tcp destination eq 12
object network NETWORK_OBJ_10.60.20.3
host 10.60.20.3
object network NETWORK_OBJ_10.60.40.192_26
subnet 10.60.40.192 255.255.255.192
object network NETWORK_OBJ_10.60.10.10
host 10.60.10.10
object network NETWORK_OBJ_10.60.20.2
host 10.60.20.2
object network NETWORK_OBJ_10.60.20.21
host 10.60.20.21
object network NETWORK_OBJ_10.60.20.4
host 10.60.20.4
object network NETWORK_OBJ_10.60.20.5
host 10.60.20.5
object network NETWORK_OBJ_10.60.20.6
host 10.60.20.6
object network NETWORK_OBJ_10.60.20.7
host 10.60.20.7
object network NETWORK_OBJ_10.60.20.29
host 10.60.20.29
object service port_tomcat
service tcp source range 8080 8082
object network TBSF
subnet 172.16.252.0 255.255.255.0
object network MailServer
host 10.33.10.2
description Mail Server
object service HTTPS
service tcp source eq https
object network test
object network access_web_mail
host 10.60.50.251
object network downtown_Interface_host
host 10.60.50.1
description downtown Interface Host
object service Oracle_port
service tcp source eq sqlnet
object network NETWORK_OBJ_10.60.50.248_29
subnet 10.60.50.248 255.255.255.248
object network NETWORK_OBJ_10.60.50.1
host 10.60.50.1
object network NETWORK_OBJ_10.60.50.0_28
subnet 10.60.50.0 255.255.255.240
object network brisel
subnet 10.191.191.0 255.255.255.0
object network NETWORK_OBJ_10.191.191.0_24
subnet 10.191.191.0 255.255.255.0
object network NETWORK_OBJ_10.60.60.0_24
subnet 10.60.60.0 255.255.255.0
object-group service TCS_Service_Group
description This Group of available Services is for TCS Clients
service-object object port_tomcat
object-group service HTTPS_ACCESS tcp
port-object eq https
object-group network DM_INLINE_NETWORK_1
network-object 10.1.0.0 255.255.0.0
network-object 10.33.0.0 255.255.0.0
network-object 10.60.0.0 255.255.0.0
network-object 10.89.0.0 255.255.0.0
access-list outside_1_cryptomap extended permit ip 10.60.0.0 255.255.0.0 10.33.0.0 255.255.0.0
access-list outside_2_cryptomap extended permit ip 10.60.0.0 255.255.0.0 10.89.0.0 255.255.0.0
access-list outside_3_cryptomap extended permit ip 10.60.0.0 255.255.0.0 10.1.0.0 255.255.0.0
access-list OUTSIDE_IN extended permit icmp any any time-exceeded
access-list OUTSIDE_IN extended permit icmp any any unreachable
access-list OUTSIDE_IN extended permit icmp any any echo-reply
access-list OUTSIDE_IN extended permit icmp any any source-quench
access-list OUTSIDE_IN extended permit tcp 194.2.20.0 255.255.255.0 host 80.90.98.220 eq smtp
access-list OUTSIDE_IN extended permit tcp host 194.25.12.0 host 80.90.98.220 eq smtp
access-list OUTSIDE_IN extended permit icmp host 80.90.98.222 host 80.90.98.217
access-list OUTSIDE_IN extended permit tcp host 162.162.4.1 host 80.90.98.220 eq smtp
access-list OUTSIDE_IN extended permit tcp host 98.85.125.2 host 80.90.98.221 eq ssh
access-list OAKDCAcl standard permit 10.60.0.0 255.255.0.0
access-list OAKDCAcl standard permit 10.33.0.0 255.255.0.0
access-list OAKDCAcl remark backoffice
access-list OAKDCAcl standard permit 10.89.0.0 255.255.0.0
access-list OAKDCAcl remark maint
access-list OAKDCAcl standard permit 10.1.0.0 255.255.0.0
access-list osgd standard permit host 10.60.20.4
access-list osgd standard permit host 10.60.20.5
access-list osgd standard permit host 10.60.20.7
access-list testOAK_splitTunnelAcl standard permit 10.60.0.0 255.255.0.0
access-list snmp extended permit udp any eq snmptrap any
access-list snmp extended permit udp any any eq snmp
access-list downtown_splitTunnelAcl standard permit host 10.60.20.29
access-list webMailACL standard permit host 10.33.10.2
access-list HBSC standard permit host 10.60.30.107
access-list HBSC standard deny 10.33.0.0 255.255.0.0
access-list HBSC standard deny 10.89.0.0 255.255.0.0
access-list outside_4_cryptomap extended permit ip 10.60.0.0 255.255.0.0 10.191.191.0 255.255.255.0
access-list OAK-remote_splitTunnelAcl standard permit 10.1.0.0 255.255.0.0
access-list OAK-remote_splitTunnelAcl standard permit 10.33.0.0 255.255.0.0
access-list OAK-remote_splitTunnelAcl standard permit 10.60.0.0 255.255.0.0
access-list OAK-remote_splitTunnelAcl standard permit 10.89.0.0 255.255.0.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool OAKPRD_pool 10.60.30.110-10.60.30.150 mask 255.255.0.0
ip local pool mail_sddress_pool 10.60.50.251-10.60.50.255 mask 255.255.0.0
ip local pool test 10.60.50.1 mask 255.255.255.255
ip local pool ipad 10.60.30.90-10.60.30.99 mask 255.255.0.0
ip local pool TCS_pool 10.60.40.200-10.60.40.250 mask 255.255.255.0
ip local pool OSGD_POOL 10.60.50.2-10.60.50.10 mask 255.255.0.0
ip local pool OAK_pool 10.60.60.0-10.60.60.255 mask 255.255.0.0
ip verify reverse-path interface inside
ip verify reverse-path interface outside
ip audit name ThreatDetection attack action alarm
ip audit interface inside ThreatDetection
ip audit interface outside ThreatDetection
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any echo inside
icmp permit any echo outside
asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_10.60.0.0_16 NETWORK_OBJ_10.60.0.0_16 destination static NETWORK_OBJ_10.33.0.0_16 NETWORK_OBJ_10.33.0.0_16
nat (inside,outside) source static NETWORK_OBJ_10.60.0.0_16 NETWORK_OBJ_10.60.0.0_16 destination static NETWORK_OBJ_10.89.0.0_16 NETWORK_OBJ_10.89.0.0_16
nat (inside,outside) source static NETWORK_OBJ_10.60.0.0_16 NETWORK_OBJ_10.60.0.0_16 destination static NETWORK_OBJ_10.1.0.0_16 NETWORK_OBJ_10.1.0.0_16
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.60.30.0_24 NETWORK_OBJ_10.60.30.0_24
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.60.30.64_26 NETWORK_OBJ_10.60.30.64_26
nat (inside,outside) source static NETWORK_OBJ_10.60.20.29 NETWORK_OBJ_10.60.20.29 destination static NETWORK_OBJ_10.60.40.192_26 NETWORK_OBJ_10.60.40.192_26 service any port_tomcat
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.60.50.1 NETWORK_OBJ_10.60.50.1
nat (inside,outside) source static MailServer MailServer destination static NETWORK_OBJ_10.60.50.248_29 NETWORK_OBJ_10.60.50.248_29
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.60.50.0_28 NETWORK_OBJ_10.60.50.0_28
nat (inside,outside) source static NETWORK_OBJ_10.60.0.0_16 NETWORK_OBJ_10.60.0.0_16 destination static NETWORK_OBJ_10.191.191.0_24 NETWORK_OBJ_10.191.191.0_24
nat (inside,outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static NETWORK_OBJ_10.60.60.0_24 NETWORK_OBJ_10.60.60.0_24 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 80.90.98.222 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 10.60.10.10 255.255.255.255 inside
http 10.33.30.33 255.255.255.255 inside
http 10.60.30.33 255.255.255.255 inside
snmp-server host inside 10.33.30.108 community ***** version 2c
snmp-server host inside 10.89.70.30 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set lux_trans_set esp-aes esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer 84.51.31.173
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 2 match address outside_2_cryptomap
crypto map outside_map 2 set peer 98.85.125.2
crypto map outside_map 2 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 3 match address outside_3_cryptomap
crypto map outside_map 3 set peer 220.79.236.146
crypto map outside_map 3 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 4 match address outside_4_cryptomap
crypto map outside_map 4 set pfs
crypto map outside_map 4 set peer 159.146.232.122
crypto map outside_map 4 set ikev1 transform-set lux_trans_set
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
crypto ikev1 policy 50
authentication pre-share
encryption aes
hash sha
group 1
lifetime 86400
crypto ikev1 policy 70
authentication pre-share
encryption aes
hash sha
group 5
lifetime 86400
telnet 10.60.10.10 255.255.255.255 inside
telnet 10.60.10.1 255.255.255.255 inside
telnet 10.60.10.5 255.255.255.255 inside
telnet 10.60.30.33 255.255.255.255 inside
telnet 10.33.30.33 255.255.255.255 inside
telnet timeout 30
ssh 10.60.10.5 255.255.255.255 inside
ssh 10.60.10.10 255.255.255.255 inside
ssh 10.60.10.3 255.255.255.255 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd dns 155.2.10.20 155.2.10.50 interface inside
dhcpd auto_config outside interface inside
threat-detection basic-threat
threat-detection scanning-threat shun duration 3600
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
tftp-server inside 10.60.10.10 configs/config1
webvpn
group-policy testTG internal
group-policy testTG attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol ikev1
group-policy DefaultRAGroup_1 internal
group-policy DefaultRAGroup_1 attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol l2tp-ipsec
group-policy TcsTG internal
group-policy TcsTG attributes
vpn-idle-timeout 20
vpn-session-timeout 120
vpn-tunnel-protocol ikev1
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value testOAK_splitTunnelAcl
address-pools value TCS_pool
group-policy downtown_interfaceTG internal
group-policy downtown_interfaceTG attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value downtown_splitTunnelAcl
group-policy HBSCTG internal
group-policy HBSCTG attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value HBSC
group-policy OSGD internal
group-policy OSGD attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-session-timeout none
vpn-tunnel-protocol ikev1
group-lock value OSGD
split-tunnel-policy tunnelspecified
split-tunnel-network-list value testOAK_splitTunnelAcl
group-policy OAKDC internal
group-policy OAKDC attributes
vpn-tunnel-protocol ikev1
group-lock value OAKDC
split-tunnel-policy tunnelspecified
split-tunnel-network-list value OAKDCAcl
intercept-dhcp 255.255.0.0 disable
address-pools value OAKPRD_pool
group-policy mailTG internal
group-policy mailTG attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value webMailACL
group-policy OAK-remote internal
group-policy OAK-remote attributes
dns-server value 155.2.10.20 155.2.10.50
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value OAK-remote_splitTunnelAcl
vpn-group-policy OAKDC
service-type nas-prompt
tunnel-group DefaultRAGroup general-attributes
address-pool OAKPRD_pool
address-pool ipad
default-group-policy DefaultRAGroup_1
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 84.51.31.173 type ipsec-l2l
tunnel-group 84.51.31.173 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 98.85.125.2 type ipsec-l2l
tunnel-group 98.85.125.2 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 220.79.236.146 type ipsec-l2l
tunnel-group 220.79.236.146 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group OAKDC type remote-access
tunnel-group OAKDC general-attributes
address-pool OAKPRD_pool
default-group-policy OAKDC
tunnel-group OAKDC ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group TcsTG type remote-access
tunnel-group TcsTG general-attributes
address-pool TCS_pool
default-group-policy TcsTG
tunnel-group TcsTG ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group downtown_interfaceTG type remote-access
tunnel-group downtown_interfaceTG general-attributes
address-pool test
default-group-policy downtown_interfaceTG
tunnel-group downtown_interfaceTG ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group TunnelGroup1 type remote-access
tunnel-group mailTG type remote-access
tunnel-group mailTG general-attributes
address-pool mail_sddress_pool
default-group-policy mailTG
tunnel-group mailTG ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testTG type remote-access
tunnel-group testTG general-attributes
address-pool mail_sddress_pool
default-group-policy testTG
tunnel-group testTG ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group OSGD type remote-access
tunnel-group OSGD general-attributes
address-pool OSGD_POOL
default-group-policy OSGD
tunnel-group OSGD ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group HBSCTG type remote-access
tunnel-group HBSCTG general-attributes
address-pool OSGD_POOL
default-group-policy HBSCTG
tunnel-group HBSCTG ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 159.146.232.122 type ipsec-l2l
tunnel-group 159.146.232.122 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group OAK-remote type remote-access
tunnel-group OAK-remote general-attributes
address-pool OAK_pool
default-group-policy OAK-remote
tunnel-group OAK-remote ipsec-attributes
ikev1 pre-shared-key *****
policy-map global_policy
prompt hostname context
no call-home reporting anonymous
hpm topN enable
: end
asdm history enableDear Darko,
The problem here is the overlapp issue with the Internal network.
Since the VPN pool is:
ip local pool OAKPRD_pool 10.60.30.110-10.60.30.150 mask 255.255.0.0
And the local network is:
interface Vlan1
nameif inside
security-level 100
ip address 10.60.70.1 255.255.0.0
So since you have some NAT rules telling the FW that 10.60.0.0/16 is connected to the inside, we need to change that and force it to know that 10.60.30.0/24 is actually reachable to the outside.
On the other hand, yes you could point to outside interface, but is not a good practice.
Thanks.
Portu.
In case you do not have any further questions, please mark this post as answered. -
TVSU 3.x fails to locate updates from new TVUR 3.0 repository
Hi,
Up until the recent upheaval when I had a working TVSU/TVUR system for -14 Thinkpad types- I have a new TVUR 3.x in place with downloads for a T42-2374.
I have a new clean install of XP on the T42 and the latest TVSU fails to locate any update packages from the new TVUR repository. On the client side I have resorted to TVSU updates from Lenovo which seems to be running perfectly well.
Can anyone confirm whether the new TVUR 3.x system actually works!
Regards.
PilooHi all
You can verify the status of the short name of the "system update" directory (the primary problem) by doing the commands below. The problem i think, starts when short name generaten is turned off when _installing_ TVSU. then the SYSTEM~1 shortname will not be generated, and the program will revert to use long names, but quoting them wrong!
try:
cd c:\program files (x86)\lenovo
dir /n /x
IF TVSU is installed while short name generation is turned on (short name generated on install) you will get something like:
20-01-2010 20:52 <DIR> .
20-01-2010 20:52 <DIR> ..
06-01-2011 10:30 <DIR> ACCESS~1 Access Connections
18-08-2009 14:11 <DIR> ACTIVE~1 Active Update
18-08-2009 14:19 <DIR> Dipmon
18-08-2009 14:17 <DIR> FPIRPOn
06-01-2011 10:25 <DIR> PkgMgr
25-10-2009 19:14 <DIR> SYSTEM~1 System Update
15-10-2009 15:56 11.264 TVSU_TPC.DLL
Notice the SYSTEM~1 shortname, if installed using no short names, that place will be blank.
As an update i can tell i 'fixed' the machine having problems by enabling the short name generation and renaming, then copying the "system update" catalog, thus generating the short name for it - everything works again :-)
PS: as a side notice on a machine with short names disabled and running as a user with a space in the user name TVSU will not even install, as it messes up with the space in the temp directoy (in the users home catalog)
But somebody really should fix this, as it is very normal to read in tuning guides for SSD drives (Thinkpads with SSD anyone to disable this short name generation among other things...
regards,
Jesper -
The error "Failed to locate a facet to be relocated..."
I am developing an application using JDeveloper 11.1.1.6.0.
My jsff file has no nested pageTemplate but still I get the error "Failed to locate a facet to be relocated. The component must have been removed from the component tree when it should not have been. Expected to find the component under component with client ID "pt1:USma:0:MAt2:0:pt1:AP1:AT1" with relative search path "_ATp:ATt1".
at oracle.adfinternal.view.faces.taglib.region.IncludeTag$RelocatedFacet.restoreFacet(IncludeTag.java:982)
at oracle.adfinternal.view.faces.taglib.region.IncludeTag.doStartTag(IncludeTag.java:199)
at oracle.jsp.runtime.tree.OracleJspBodyTagNode.executeHandler(OracleJspBodyTagNode.java:50)
In general, my applicationPanel is built in a pageTemplate. Inside the applicationPanel, I have an applicationTable comonent with id AT1. Inside its "table" facet, I have a table component with id "ATt1". The jeff file is called to open an object view in a dynamic tab in the local area. A different object will open a different tab. First time to open an object, I won't get the error. But if I switch the view between two tabs, I will get the error.
The most interesting thing is that if I remove "binding" property inside of "ATt1" table, the error will be gone. But I have to use "binding" property for other uses.
Please let me know if you have any idea on how to resolve this.
Thanks,
Weihong
Edited by: user731346 on Aug 31, 2012 3:26 PMHi,
if it is the JSF component binding then what scope is the managed bean in ? If you open the same JSf in different tabs and the binding points to request scope (or a shared scope) then the problem is that you use the same component reference twice. Use backing bean scope for the component binding bean in this case
Frank -
Failed to locate project named ... in SSIS 2012 package scheduled in agent
Hi
I have 2 packages that are deployed using Project deployment model on a, the are scheduled to run every 1/2 hour, for the last 2days the have been failing with Failed to locate project named ...:A .Net framework error occurred during execution of user defined
routine or aggregate "decript_binarydata": System.IO.LoadException Could not load file or assembly.....The thing is that the package was working without issue, this seems to be a decryption issue, so I believe it is to do with Project Deployment
model, but I am not sure
Any help would be much appreciated
Regards
Andy
CRM 4, SQL Server and .Net developer using C#Hi Andy,
Based on my research, please refer to the following suggestions to fix this issue:
Change the SQL Server Service Account from built in default “NT Service\MSSQLSERVER“ to another account with admin rights on the system.
Grant appropriate permissions to SQL Server Service Account & SQL Agent Service Account.
1. Note down your SQL Server Service Account & SQL Agent Service Account.
2. Go to Start-> Run-> secpol.msc-> Local Policies->User Rights Assignment
3. Check if these 2 accounts are a part of the following policies.
• Log on as a service
• Act as part of OS
• Adjust memory quotas
• Logon as batch job
• Replace a process level token
4. If not, add them explicitly.
5. Reboot the machine
Repair the SQL Server instance to test the issue again.
The following two blogs are for your references:
http://blogs.msdn.com/b/dataaccesstechnologies/archive/2012/08/20/error-while-deploying-ssis-2012-project-from-ssdt-to-ssis-catalog-system-componentmodel-win32exception-a-required-privilege-is-not-held-by-the-client.aspx
http://blog.oraylis.de/2013/09/fixing-sql-2012-ssis-deployment-error-6522-a-required-privilege-is-not-held-by-the-client/
Thanks,
Katherine Xiong
If you have any feedback on our support, please click
here.
Katherine Xiong
TechNet Community Support -
Can't scan a collection using endpoint, "Failed to initiate client side operation."
i'm trying to do a quick endpoint scan of a collection and get the error, "failed to initiate client side operation." I click the details button and I get this:
Not found
Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlQueryException
The SMS Provider reported an error.
Stack Trace:
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.ExecuteMethod(String methodClass, String methodName, Dictionary`2 methodParameters, Boolean traceParameters)
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.ExecuteMethod(String methodClass, String methodName, Dictionary`2 methodParameters)
at Microsoft.ConfigurationManagement.AdminConsole.ClientOperation.Utilities.ExecuteClientOperation(ConnectionManagerBase connectionManager, ClientActionType operationType, String collectionId, String collectionName, List`1 validMachineIds, IResultObject
selectedMachines)
System.Management.ManagementException
Not found
Stack Trace:
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.ExecuteMethod(String methodClass, String methodName, Dictionary`2 methodParameters, Boolean traceParameters)
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.ExecuteMethod(String methodClass, String methodName, Dictionary`2 methodParameters)
at Microsoft.ConfigurationManagement.AdminConsole.ClientOperation.Utilities.ExecuteClientOperation(ConnectionManagerBase connectionManager, ClientActionType operationType, String collectionId, String collectionName, List`1 validMachineIds, IResultObject
selectedMachines)
I have absolutely no idea how to fix it. I've tried resetting the site, uninstalling and reinstalling the SCCM console from the SP1 media, verifying that WMI is set up correctly, reinstalling the SCCM client on my server, restarting the server... I've
got nothing. Does anyone have any suggestions?What version is the client running? Do you also have Cu1 installed, if so, did you also upgrade the clients?
Kent Agerlund | My blogs: blog.coretech.dk/kea and
SCUG.dk/ | Twitter:
@Agerlund | Linkedin: Kent Agerlund |
Mastering ConfigMgr 2012 The Fundamentals -
Failed to locate content SCCM 2012 SP1
Hi, I am trying to deploy Firefox but have not been succesfull so far. I keep getting "failed to located content" when I try to install it from a workstation. Any idea on where I can start looking to troubleshoot this?
Hi Torsten,
Sorry for disturb you but I have a same problem.
I deploy a program and 2 computer is perfectly installing. Now status is content download but another 2 computer get a same
Failed to locate content status but a description is success and why 0 the error code?
( Boundary Group and distribution is ok )
ps: It's large program ( 8 GB and 8000 file) and the SCCM transform it 24 GB and 30000 filein the DP.
Thank you for your help
( I can't insert print sceen)
Peter -
WCS with location doesnt locate clients
I have WCS with location installed. From the Cisco documentation the WCS with location is suppose to provide a small set of location/mapping functions. Adding the location appliance will give you historical data.
When trying to view clients on the floor map it says that "No clients found on this floor. Either you dont have any location server which locates clients or no clients are detected."
There are several clients that are online and show up in the other search function but they arent mapped out.
Any ideas?I'm having a similar problem with WCS not displaying my client(s) on the Heatmap. I have setup a lab environment with a single 2006 controller and 2 1010 APs. I walked around the perimeter of my office space to verify roaming between controllers but WCS still doesn't display my client. When I try to reload the heatmap it says:
Loading clients..
Loaded 0 out of 0 Clients.
I have also verified that Clients are not being filtered from the view.
Any more ideas?
Any help is appreciated. Thanks! -
Co-Locate Client Access and Edge Transport Role on Same Server?
Co-Locate Client Access and Edge Transport Role on Same Server?
Is it possible/supported to install the Edge Transport Server Role on the same machine that the Client Access role is installed on now that 2013 SP1 has added support back in for the Edge Transport Role?
jonNo.
Unless something has radically changed from before...
EDIT
No, nothing has changed:
"If you want to install the Exchange 2013 Mailbox or Client Access roles on a computer, see
Install Exchange 2013 Using the Setup Wizard. The Edge Transport role can't be installed on the same computer as the Mailbox or Client Access server roles."
http://technet.microsoft.com/en-us/library/dn635117(v=exchg.150).aspx
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you. -
Essbase Administration Console error "failed to create client directory to write error file"
I am getting the following error while trying to load data using EAS v11.1.2.3
"failed to create client directory to write error file"
Any known root cause for this.Check the default error directory while loading data? The error file in 11.1.2.2 points to C:\Oracle\Middleware\EPMSystem11R1\products\Essbase\eas\client, which is already on the system where EAS is installed.
If the folder is not there then it is a bug, however you can change it to an existing path.
Regards
Celvin
http://www.orahyplabs.com -
Failed to create client for Net8 Service
Using Windows 2000.
I have tried to install Oracle Forms and Reports 6i and Oracle 8i Personal Edition six times now with no success. I install Forms and Reports first. However, I am unable to get past an error when installing the Reports. The error message states "Failed to create client for Net8 Service". I get the erro about 30 seconds into the installation of Reports. Forms installs just fine.
The procedure I am using can be found at course.com using the ISBN # 0-619-03549-8 and the instructions for the 2nd edition of the "Enhanced Guide to Oracle 8i" by Morrison and Morrison for Windows 2000. This is for a class that I am taking at DeVry.
I have followed the instructions to a "T" during the installation process and also for when I uninstall the software to try it again.
Is there a simple answer to why the software can't create the Client for Net8 Service?
Any help would be appreciated.
Thanks
Leo DonahueHi ...
I don't know whether urs and mine is the same scenario..
I have tried to install forms in windows XP also. getting the same error message. One more thing. I was trying install forms and reports. If 'm installing forms first,It'll get installed with out any probs. Then this error will come in reports installation and vice versa.. 'm getting it from 3 workstations. plssss help me....
Any help will b greatly appreciated..
thanks. -
Memory Card Manager keeps poping up and stating "failed to locate supported file types or there are no photos on thisw device"
Please advise reason or solution.Hi
I got a similar error: "Failed to locate file types or there are no photos found. I hooked up and external Buffalo hard drive. I moved my iTunes folders. After I moved the files found the correct way to move files to a new drive for iTunes. So I did Edit preference, change F:\iTunes. However after syncing nothing is on my ipod now and I am getting the error "Failed to locate files". Any solutions.
Thanks much. -
CJS-00081 Assertion failed: No db client software version available
Hi Experts,
I'm doing system copy on Oracle.9.2 and SAP R/3 Enterprise 4.70 Ext.Set 1.10 SR1 in AIX5L, I haved check Note:659509,
during run the Installation Master,The Central Instance and Oracle software is installed and when I installing Database instance, the error massage show up as following:
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_ClientVersion.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_ClientVersion.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_ClientVersion.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tORA_TablespaceNameMapping.insertRow(), inserting
TRACE [iaxxhcache.hpp:534]
CDomainObjectCache::readFromKeyDb(iastring, bool, const iastring &)
CDomainObjectCache::readFromKeyDb: Reading from tGlobalDbParameters WHERE dbSid = 'PRD'
TRACE [iaxxejsexp.cpp:138]
EJS_Installer::writeTraceToLogBook()
tGlobalDbParameters.updateRow(, WHERE dbSid = getContextParameter('dbSid')), updating
ERROR 2011-06-25 07:29:41 [iaxxinscbk.cpp:219]
abortInstallation
CJS-00081 Assertion failed: No db client software version available in tORA_ClientVersion for client type AIX_64
have any advice?Oracle 9 is out of support. Why are you using this version. You can install R/3 4.7 on Oracle 10g, and as per your problem have you installed oracle through setup.exe or Sapserver.cmd ?
Regards,
Subhash
Maybe you are looking for
-
I have just purchased an iPad 2. I have wi-fi for roku and have connected the iPad to it. I want to print to my usb printer. My connection is: Cox Cable spit to telephone and broadband. The broad band feed goes to a Cox modem and feeds the wi-fi
-
i can't restore and update ios 4.2 in my ipod touch,iTunes displays a message saying"an unknown error occurred (-1)".
-
How to present the reports to superiours
Hi, I have got the reports ready for presenting to all FI Managers, but i'm in dilemma in presenting the reports to FI Managers, the reports are getting excuted in the browser. Can anybody tell me how to present the reports to Fi
-
How do I undo annotations in reader? iOS
I a, wondering what I have to do to undo annotations in reader for its.
-
Hi there, I have tried to update 7.2 and all of my Apps have disappeared. I was advised to restore so not sure what is going on?