BEFW11S4- problems with internal firewall?

Hi,
I have had this router for the past three years. We had to movfe the set-up around and now we can not access certain websites due to security issues. I contact my ISP and when I hook my computer up directly to the ISP modem all the websites work. When I hook up my linksys router I can't access them any longer. My ISP told me this is because of an internal firewall in this router. Any suggestions on how to change these internal settings. I read through the user guide and I'm guessing that i need to reconfigure everything, but wanted to ask first!
Thanks!

i think you should try upgrading the router's firmware .. after the upgrade reset and reconfigure the router ..

Similar Messages

Problem with internal speakers of MacBook Pro

Hi,
I wanted to know if anyone have experienced a problem with internal speakers of Mac Book Pro. In my MackBook the Internal speaker volume goes down automatically. I checked the System Preferences>Sound>Output , from there I check that it is in the middle ( Balance) However, the problem is still the exists. Just for testing I played an audio file and I moved the bar toward the right speaker it is the same and when I move toward the left speaker the whole sound goes off . Looks like one speaker stops working completely. Then I checked the Utilities > Audio MIDI Setup > Configure Speakers from there I checked both left and right speakers and the channel frequency is fine. Still same issue. I have no idea what is going on , I really need your suggestions to get this fixed.
Thanks in advance.

Try the following:
http://support.apple.com/kb/HT1411 Apple Portables: Resetting the System Management Controller (SMC) and http://support.apple.com/kb/PH11243 OS X Mountain Lion: Reset your computer’s PRAM
Also, consider installing Boom

I am getting problem with internal table & work area declaration.

I am working with 'makt' table ..with the table makt i need to work with styles attributes ..so i declared like this
TYPES : BEGIN OF ty_makt,
         matnr TYPE makt-matnr,
         spras TYPE makt-spras,
         maktx TYPE makt-maktx,
         maktg TYPE makt-maktg,
         celltab TYPE lvc_t_styl,
       END OF ty_makt.
DATA : i_makt TYPE TABLE OF ty_makt.
DATA : wa_makt TYPE ty_makt .
    But end of program i need to update dbtable "makt"...i am getting problem with internal table & work area declaration.
i think makt table fields mapping and internal table/work area mapping is not correct. so please help me to get out from this.

Hi Nagasankar,
TYPES : BEGIN OF TY_MATNR,
              MATNR TYPE MAKT-MATNR,
              SPRAS TYPE MAKT-SPRAS,
              MAKTX TYPE MAKT-MAKTX,
              MAKTX TYPE MAKT-MAKTG,
              CELLTAB TYPE LVC_T_STYL, " Its Working perfectly fine..
             END OF TY_MAKT.
DATA: IT_MAKT TYPE STANDARD TABLE OF TY_MAKT,
          WA_MAKT TYPE TY_MAKT.
Its working perfectly fine. if still you are facing any issue post your complete code.
Thanks,
Sandeep

Problem with IPV6 Firewall since firmware 7.6.1

I have problem with IPV6 Firewall (port forwarding using a HE tunnel) since firmware 7.6.1 upgrade, IPV6 oubound is working, but ports are not forwarding to my local IPV6 adress, have used IPV6 Firewall, and it worked before
Ant sugesttions, solutions?

Go back one firmware version into release 7.6
I had similar problems with an IPv6 tunnel not working anymore after the 7.6.1 upgrade.
When I 'rolled' back to 7.6, my IPv6 tunnel came back working.
I also use the old Airport Express application on my OS/X, the new one with the globe on the black screen is missing IPv6 tabs in the application..

Problem with internal HD upgrade- Flashing "?" over HD icon on startup

Last weekend, I installed a Western Digital 250GB internal IDE 2.5 inch drive (WD2500BEVE) to replace the internal HD on my 15 inch G4 PB Aluminium (not sure of processor speed, but purchased new in 2004, with OSX 10.4.11). I backed up my existing HD to my friend's MacBook, as a disk image using Carbon Copy Cloner. I was very careful with the installation (using anti-static wristband etc etc). The installation appeared to go well. The newly installed internal HD could be mounted as an external HD of my friend's MacBook (using firewire Target Disk mode). Carbon Copy Cloner copied everything back to the new internal HD without any apparent problems.
BUT THEN... when I disconnected the firewire connection and tried to start my computer on its own, the dreaded 'flashing question mark over hard drive' icon appeared.
Can anyone suggest what the problem might be? Three things I've already excluded are:
(1) The jumper settings on the HD are correct.
(2) I formatted the new HD as Mac OS extended (journaled)
(3) The problem is not with the master boot sector (i.e. the problem is not merely that the computer can see the HD but does not know how to load the system from it). My computer cannot see the HD at all -- when I insert my operating system DVDs as if to reinstall the system, my internal HD does not even appear.
I am not panicking as I can still view the contents of my internal HD by booting it as an external HD of my friend's computer. But there seems to be a problem with my CPU communicating with my internal HD. The core of the mystery is: why can I boot my new internal HD off my friend's computer using FireWire, yet when I start my computer on its own using the operating system DVDs, the computer doesn't seem to recognise the HD whatsoever?
Does anyone have any suggestions?

Can we establish what model Powerbook you have? Take the battery out and look for the label.
I have a feeling that your PB cannot recognize the 250GB drive, although I was under the impression that the older PBs that could only recognize 128GB would simply ignore the extra disk space. Perhaps the ATA specs aren't all backward compatible, although the Firewire interface can handle it.
Other World Computing can obtusely point out which drives your model can handle, although I don't know it its 100% accurate.
http://eshop.macsales.com/MyOWC/

BEFW11S4 problem with XP

I have a BEFW11S4 v2 that I've been using at home for a number of years to support two wired computers upstairs, a wireless one downstairs and the occasional transient. So far, I've not had any problems with wireless connections.
Originally, both wired systems were Win98 and worked flawlessly. When one of those systems was upgraded to XP Pro it started having problems losing the connection to the router. Attempting to reconnect using the Windows repair button or manually requesting a new IP address fail. I would have to shut down the XP system, shut down the router, then power them up, router first, to get everything running again. Since my daughter took the XP box to college, it wasn't all that big a deal. However, I have since upgraded the other system to XP Pro SP2 and it now has exactly the same problem. XP is current with all patches and the BEFW11S4 v2 has the most recent firmware.
The system seems to remain connected as long as it's in use, but if left unused for more an 24 hours it usually loses the connection and must be rebooted.
Any ideas what's different between 98 and XP that may cause this?
I appreciate any suggestions.
Mike

I'm having a similar problem - router has been working well for the last several years with two systems - W98 and WXP Pro. Added a second/new XP Pro system and now router hangs and must be rebooted anywhere from every 5 minutes to several hours when new XP Pro system is powered on. Still no problems at all with either of the other two systems. I've checked the MTU value and it is correct. Any solutions out there for this problem? I can supply config information if that would help identify and fix the problem.

BEFW11S4 Problems with Laptop and Xbox 360

For the past few weeks my Linksys BEFW11S4 has been malfunctioning. When I try to connect to the wireless network from my laptop, it says "Not Connected" but I can still access the internet for a few minutes before it really disconnects. Unplugging the router and plugging it back in lets me connect again, but still it gives the "Not Connected" message and boots me off within a few minutes. It has also been causing problems with my Xbox 360. It is connected with an ethernet cable to the router, but every time I turn the Xbox on it says that it is not connected. After I unplug the router and plug it back in, the problem is fixed, and I can go online on my Xbox for as long as I want. Anyone know how to fix this?

It seems that router is not configured properly ..... checkthe firmware version on the status page of router ..... .
Upgrade the firmware if required .....

EA6500 - Problem with Ipv4 firewall disabled

I'm encountering the same issue described on this thread: http://homecommunity.cisco.com/t5/Wireless-Routers/EA4500-Problem-when-SPI-IPv4-is-disabled/m-p/5520...
But with my new EA6500.
When i disable the IPv4 firewall, i'm not able to access a lot of websites(the homecommunity included).
I think its time to take some action about this problem, i want to access my router remotely, but if i disable the firewall i cant acess it.
This is very disappointing

I have some equipaments that i need to access remotely, like my IpCameras purchased together with the new router. With the firewall enabled, i'm not able to connect with them.
With my old router(its old, sooo old), i dont have any of this issues, but i'll give a try when I get home today, i'm in work now, but i have no expectation that will work.
This is a strange and non sense bug, cause i'm acessing the sites, not the sites accessing my router, a disabled firewall could not be a problem, not to access a web site.
I have problems of many disconnects too, like i saw in other threads, but this is another subject.
I think all that i can do is wait till a FW update, cause i'll not be able to return the router, and my old router is **bleep**
Thanks for the replies.
EDIT: I forgot to mention, before post here, i already tried to reset, re-configure so many times. I'm with the latest FW.

Bizarre problem with internal drive

I have a 15" G4 PPC 1ghz Powerbook with 1gb SDRAM. A couple of years ago the hard drive failed. I bought another and replaced it, only to find that there seemed to be a problem with the new one as well. To cut a long story short: I needed a working machine, so mothballed it and bought a new one. for various reasons I'd now like to get it going. So...
Yesterday, I started it up. As expected it couldn't find it's own drive and just gave me the grey screen with the file/question mark icon. I shut it down and plugged in an external firewire enclosure containing a working 60gb drive with a full bootable OS installed (for brevity I'll call this Drive 1 from now on).
I started it again and it booted from Drive 1. It worked fine. I then shut it down, opened it up and replaced the internal Drive with Drive 1. I put everything back in place (being careful to make sure the drive was properly connected) and hit the on button. Again the file/question mark icon. I tried booting whilst holding down the "c" key. Didn't help.
So, I then plugged in another Firewire bootable drive (Drive 2). It booted from Drive 2 no problem. So, at this point I'm thinking, "Well, I've probably damaged the hard drive connecting cable - better get a new one". Never-the-less I thought I'd run a few test. And this is where it gets slightly bizarre:
I stuck in the Apple Hardware test disk, shut the machine down, removed Drive 2, started it again then ran a full hardware check, it told me: Airport - passed, logic Board - passed, mass storage - passed, memory - passed, modem - passed, video ram - passed. As there was no other Drive present this means it was detecting and okay-ing Drive 1, right?
I shut it down replaced the firewire Drive 2. Re-booted. Then opened "About this Mac". Under ATA it clearly shows a FUBITSU 55.89GB Drive. Which is Drive 1. (Drive 2 comes up under "Firewire" as SMARTDISK CORP).
The details given for Drive 1 are as follows:
Capacity: 55.89 GB
Model: FUBITSU EHT2060AT
Revision: 0124
Serial Number: FN4****B55
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ATA
Unit Number: 0
Socket Type: Internal
Low Power Polling: No
Mac OS 9 Drivers: No
Partition Map Type: Unknown
S.M.A.R.T. status: Verified
I also looked in Disk Utility. In the column on the left, at the top it shows Drive 2 with the Firewire icon. As per usual, it shows twice, once a the top with the manufacturer's name and again underneath with the name I gave it when I formatted it. If you click on either, it offers you all the usual options for Verifying and Repairing Permissions.
Underneath that is a listing for the Drive 1 with the Internal Drive icon. This it shows only once - the listing with the manufacturer's name. If I highlight it the verify/repair options are all greyed out and unavailable.
The last thing I can think of that may be of any help is that if I open carbon copy cloner it only only shows Drive 2 and doesn't pick up the internal.
Could it be a partially damaged cable? Meaning the machine sees the drive but can't use it? Any ideas would be most welcome.
ET
<Edited by Moderator>

Hi does sound like the cable but did you try running the hardware test CD with the internal drive installed and did it report it? These you could try while waiting on a new ribbon cable.
Also in the system profile was the internal drive selected as boot drive, you can set this using the OS X installer disk by booting from it.
Long shot, is your PRAM battery good? If not that might be the problem, does your date and time stay correct or does it need to be reset on bootup? If it's dead the PowerBook might not be seeing the internal drive or perhaps as I've seen on some PowerBooks it takes a few seconds to a minute for the PowerBook to go down the list and find the bootable drive so guess the final question was were you waiting long enough?
Kevin
<Edited by Moderator>

Problems with internal memory

Hello people,
I have a problem with my iPhone. If I go to Usage window in my settings, it says "4.2GB used". However, if I count all MB's of the apps listed below, I don't even get near 4.2GB. It's about 1.3. How is this possible? I know the OS needs some space, but it can't be this ridiculous... This really is a struggle and I hope someone can help me out.
iPhone 5c 8 GB. iOS 8.1.3.

Try to remove some applications that use iCloud. go to settings -> iCloud -> Archive -> Manage space -> choose if you want to delete something backup or e-mail etc ...

Having problems with internal speakers?

Hello,
          I've recently encountered a problem with my speakers. There is also a red light coming out of the audio jack. I found out that many other people are having the same problems with newer Mac versions. I looked at many different discussions and some are wrong and some are right. Here is a great idea for for making this work: 1) You can use a toothpick. From what I've read, it may work, but be very careful of what you're doing. 2) I've used this idea it works very well. Find a headphone or audio jack cord and plug it in the audio jack many times. What I did was plug it and unplug it very fast. What you're trying to do is confuse the computer for a bit then make it realize that there is nothing in the audio jack. This should work. If it doesn't (for whatever reason) do not use the extra money to get it fixed. If this isn't enough help look at some other discussions, it's how I solve my origional problem with my speakers.
                                                                                                                                                          Hope you find this helpful,
                                                                                                                                                                                                     Adam B.

No, its too expensive for HP to plate the zif connectors with something that doesn't corrode....rolleyes.
Thanks nice tutorial.
The DV 6000 series was plagued with motherboard issues
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=ca&docname=c01087277

Problem with internal update server

Hello everybody,
after setting up an Adobe Update Server that works fine with updates for CS6,I would like to use this update server for additional Adobe software like Flash Player and Reader.
I think I made every steps as mentioned in the administration guide of flash player: http://wwwimages.adobe.com/www.adobe.com/content/dam/Adobe/en/devnet/flashplayer/pdfs/flas h_player_11_6_admin_guide.pdf
Which means:
I can access the URL: "http://SERVERNAME/pub/flashplayer/update/current/sau/11/install/" with its 3 *.z files (install_all_mac_pl_sgn.z,install_all_win_ax_sgn.z,install_all_win_pl_sgn.z) and "http://SERVERNAME/pub/flashplayer/update/current/sau/11/xml/" that contains the version.xml-file.
I've also added the mms.cfg file with UTF-8 and the content:
AutoUpdateDisable=0
SilentAutoUpdateEnable=1
SilentAutoUpdateServerDomain=SERVERNAME
SilentAutoUpdateVerboseLogging=1
Unfortunately there aren't any updates for my test-client.I read something that with these options the "Update Section" in the "Advanced"-tab should be greyed out, but it isn't.And if I'm going to click "Check now" my browser is opening the Adobe homepage.
The problem is that we can't use any WSUS for this scenario.So we have to deploy the mms.cfg-file by copying it to the clients manually (maybe via batch-file later).
That's the first problem.
The second one is that we would like to update the Adobe Reader via the same update server.But I didn't find any guide on how to solve this.
Following information regarding our scenario:
AUSST is running on a Windows Server 2003 Enterprise SP2 with IIS6
Created a new website "Adobe Update Server" and added the handlers for xml,sig,crl,dmg (I had to remove the handler for zip after having problems with it) and added these handlers in the <httpheader>-Section of the webconfig.
Created a new folder with the structure: pub/flashplayer/update/current/sau/11/ install and xml.
Installed Flash Player 11.3 on my test-client
Allowed extensions: All unknown ISAPI-extensions,Active Server Pages,ASP.NET v1.1.4322,ASP.NET v2.0.50727,Front Page Server Extensions 2002,Serversided includes (SSI),WebDAV
I know that I maybe allowed too much extensions because my knowledge with Server 2003 isn't that well.
Sorry for my bad english,I've also tried to open a discussion in the german section but there wasn't any reply yet.
It would be great if there is anybody who could help me with my problems because this features are some kind of "must-have" and I would like to take this big step.
I appreciate every help and post in this discussion as I'm kinda stuck with these problems.
kind regards

[Moved the discussion to Enterprise Deployment Forum]

3000 J - Problem with Internal Modem

Hello,
I still live in the 90's and use dial-up service to access the internet. My computer isn't recognizing (or there is a problem with) my modem. I receive "Error 797" when trying to dial-up as I usually do.
The modem is HSF2014 56K Data Fax Modem. Is there a way to obtain the driver software from Lenovo on CD-ROM, so I can try reinstalling?
Thanks in advance!
Ryan

Hi again,
It's difficult for me to offer anymore than generalized advice but I'll try to be helpful.
I'd start by removing the existing modem and restarting the computer. One of the error messages mentioned PCI Slot 1. This is probably the modem. If ALL the error messages go away it's a pretty good indication that the modem is the problem and replacement is in order. I would attempt simply re-seating the modem in it's slot first however and restarting.
I'm pretty sure that the proper drivers would be found automatically for the existing modem. If not, there's a rather generalized Readme file and a program called HXFSetup.exe which is probably the program you would need to run if required.
While you're in the computer, disconnecting and reconnecting things might be better than just a visual inspection. Twisting the cooling fan housing on the CPU with moderate force shouldn't hurt anything and who knows?
If it turns out that the modem is the problem (which I doubt), installing the other modem shouldn't be a problem, assuming it fits and you have the drivers for it. Again, good luck.
Jim
P.S. If you haven't already done so, Google all the error messages and see if there seems to be any common element. There are diagnostic programs available on the web but I've never found one that helped me with a trouble, perhaps someone has and can make a recommendation.

Linksys Router BEFW11S4 problems with iphone

i have a linksys router bedfw11s4 version 4 and im having problems with wifi on my iphone
i can search and connect to my router but the interent is extremely slow
i have no problems with my laptop
i read some info on this board regarding changing it to static ip but im having problems figuring out how to config it
when i goto into my router setting i only see 1 DNS address

So on your IPhone you are getting connected to your Wireless Network, but the Internet is working slow, then i would suggest you to change some settings on your Router....
Once you login to the router setup page, Under Wireless ... Change the Wireless channel to 11-2.462GHz and click on Save Settings....
Then under Advacnce Wireless Settings.... Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings".....
Now check if your IPhone, how is the Internet Speed....
If still slow then i would suggest you to upgrade the firmware of your Router....
Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop..
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Problem with internal drive or a s/w bug that can be swatted?

Dear ones,
Recently I was greeted with a "persistent grey screen" upon startup. A restore using TimeMachine was unavailable according to Disk Utility. I ran an Extended Hardware Test. No problem indicated.
<rant>Two years of slow response and waiting for TimeMachine backups—what a waste of time—I bought a separate disk just for TimeMachine—what a waste of money. </rant>
I ran Disk Utility Permissions Repair from the SL install disk.
I ran Disk Utility Repair Disk from the SL install disk.
The error messages were:
"Unused node is not erased."
"Node = 192"
"Invalid key length"
I made a quick back-up using Disk Utilities—Restore to a newly-formatted disk which failed.
My internal 120GB "disk could not be validated."
I made a CCClone and a SuperDupe as best I could on a freshly formatted and partitioned outboard drive.
I formatted a second outboard fw800 hard drive and Installed SL on it, updated it and used Migration Assistant to move the files to the fresh boot disk.
Just before the migration finished, the screen turned dark grey and a multi-language alert appeared in white letters "You need to restart your computer. Hold down the power button until it turns off, then press the power button again." This has happened a few times on my wife's computer but this was a first for me.
I redid everything.
I ran Disk Utilities on the fresh drive and got a repeat of the original error message on my internal drive when I tried to repair the disk.
"Unused node is not erased."
"Node = 192"
"Invalid key length."
It seems as though the problem has migrated to the second boot drive.
Running Disk Utility returns the message, "Disk Utility Can't Repair The Disk…" for either the clone copy or the dupe copy.
I have followed all the steps in the order suggested in the link http://support.apple.com/kb/TS2570 without success.
I don't know whether to get a copy of something like Disk Genius, Drive Warrior, or a new drive. They're all about the same price.
Anyone got any ideas about saving anything?
My home drive can't be validated.

stan wrote:
<rant>Two years of slow response and waiting for TimeMachine backups—what a waste of time—I bought a separate disk just for TimeMachine—what a waste of money. </rant>
That's not normal. It indicates you've been having some sort of problem for two years.
I ran Disk Utility Permissions Repair from the SL install disk.
You should run that from the OSX volume. See [About Disk Utility's Repair Disk Permissions feature|http://support.apple.com/kb/HT1452].
A restore using TimeMachine was unavailable according to Disk Utility.
Huh? You don't restore from Time Machine backups via Disk Utility.
"Unused node is not erased."
"Node = 192"
"Invalid key length"
The file system is corrupted. It's possible a heavy-duty 3rd-party +Disk Repair+ app, such as Disk Warrior, can repair it. They're not cheap, though. DW is about $100.
I made a quick back-up using Disk Utilities—Restore to a newly-formatted disk which failed.
My internal 120GB "disk could not be validated."
Probably because that type of backup copies the corruption.
Try a full system restore from your TM backups, per #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum).
But in step (c) there, take the time to reformat your internal HD. It will only take a moment.
Since you've apparently had this problem for a while, it's possible it will restore, but not start up. If so, just install a fresh copy of OSX from your SL install disc. That won't affect anything else.
Message was edited by: Pondini

BEFW11S4- problems with internal firewall?

Similar Messages

Maybe you are looking for