Best HD camcorder under $1000

Can anyone recommend a HD camcorder under $1000.00 to be used with final cut pro x and a 2010 unibody MacBook pro?
Any information will be helpful.
Thanks!

I've seen very good reviews for the Panasonic TM900. It works with FC, does 50/60P, and is now on sale.... I could've picked one up for $699 (Canadian) in Best Buy.

Similar Messages

  • The best audio interface under $1000?

    Any suggestions out ther for what you cansider the best bang for your buck? People keep talking about the MOTU 828mkII but I can't remember how much they cost at this time. And I haven't had any problems with my M-Audio Firewire 410.
    It does a good job and gets me by but when the time comes to start recording full drum sets I'll need a good investment to last me some time.

    wow....that's a better response than I expected! Looks like I have my work cut out for me as far as research is concerned. The Motu 896 sounds like a great unit...I've been looking into the PreSonus Firepod too but haven't been able to make my mind up on anything yet. I won't be getting one for a short while but wanted to see what was out there...
    I'm going to have to look into all those other ones too...never heard of the RME FireFace800 but I like the convenience of a firewire interface.
    The Sappire Pro I've never heard of either so I'll have to research that one as well as what's up with a Metric Halo 2882. All new to me!
    Thanks alot!
    If anyone else has suggestions...please pass them in!

  • Aspiring professional; focus on newborns and children; lense under $1000? (t4i rebel)

    I'm a hopefully hobbies looking to go pro by specializing in newborns and children. I do my work inside and outdoors so I will need a lense that plays well with low light, artificial light & natural llight. Recommendation for the best newborn lens under $1000?

    You need a fast lens and a macro for newborns.  I primarily used my 100mm macro with my newborns, but I use my own lighting so I don't need a really wide aperture.  I do pull out my 50mm 1.4 and 85mm 1.4 for natural light or really small depth of field, but it's more rare.  The 24-105 mentioned above is a great lens, but I've never used it for newborns or children in a studio setting.   I don't normally need the flexibility of a zoom in the studio so I'd prefer the sharpness of a prime and the speed if I need it.  But mostly I want something that can focus close to the subject in-case I want to get in tight when I see an opportunity.  There's nothing worse than missing a shot because your lens can't focus close up.  With children you won't need the macro and will want something wider (50mm is a good portrait length) for your crop sensor camera, unless you have a ton of room in your studio.

  • What is the best miniDV camcorder to buy to export miniDV tapes to Macbook pro?

    Hey there,
    I have miniDV tapes with home videos that I want to export to iMovie or FCP 5.0 so I can turn the footage into digital video clips to burn to DVD's.  They were shot on a Sony handicam that no longer works.  I bought a Panasonic PV-gs15 in order to do the job but it doesn't export video, only pictures from SD card. Now I just want to get the best camcorder or device (within financial reason) for the job.  Can anyone tell me the best way/Camcorder to get this video off these miniDV tapes and onto my computer please?

    Hi
    May be You find something of interest in my notes regarding this (and iMovie - but it is General)
    NO CAMERA or A/D-box
    Cable
    • Are You sure that You are using the FireWire Cable - USB-Cable will not work for miniDV tape Cameras
    FireWire - Sure not using the accompany USB-Cable but bought a 4-pin to 6-pin (or 9-pin) FW one ?
    • Test another FW-Cable very often the problem maker.
    Camera
    • Test Your Camera on another Mac so that DV-in still works OK
    • Toggle in iMovie pref. Play-back via Camera (on <-> off some times)
    • Some Cameras has a Menu where You must select DV-out to get it to work
    • Camera connected to "charger" (mains adaptor) - not just on battery
    • Camera set in Playback mode - NOT Recording mode
    Does Your Camera work on another Mac ?
    Sorry to say it is to easy to turn the 6-pin end of the FW-cable 180 deg wrong.
    This is lethal to the A/D-chip in the Camera = needs an expensive repair.
    (Hard to find out - else than import/export to another Mac ceased to work
    everything else is OK e.g. recording and playback to TV)
    A/D-box
    • Is the dip-switches set right ?
    • Set to same standard as recorded/editing e.g. NTSC 29.97fps or PAL 25fps
    • Try resetting it
    Connections
    • Daisy Chaining most often doesn’t work (some unique cases - it’s the only way that work (some Canon Cameras ?))
    Try to avoid connecting Camera <--> external HD <--> Mac but import directly to the Mac then move
    the Movie project to dedicated external hard disk.
    • FireWire-port - Can be re-setted by - Turn off Mac and disconnecting Mac from Mains/Power for 20-30 minutes
    External device’s (hard disk’s)
    • Should be FireWire as USB/USB2 performs badly and so does Airport or Net-work connected ones too.
    • MUST BE - Mac OS Extended formatted - UNIX/DOS/FAT32/Mac OS Exchange - DO NOT WORK for video due to 4Gb barrier.
    Mac
    • Free space on internal (start-up) hard disk ? Please specify the amount of free space.
    (Other hard disks don't count)
    I go for a minimum of 25Gb free space for 4x3 SD Video - and my guess is 5 times more for 16x9 HD ones
    after material is imported and edited. No Camera or A/D-box
    • GarageBands fix - Close iMovie, Open GarageBand, Play some notes, Close GB and iMove can now be OK
    • Does Your Mac have a FireWire Port
    • White MacBooks - don't
    • MacBook-Air - don't
    if not then a few Mac’s has a PCM-CIA slot and there are FW-Cards that makes a FW-port this way
    else - NO SOLUTION
    Only option as I get it is either
    • Use another Mac to Capture material (to an external USB2 - Mac OS Extended formatted hard disk - or -
    • Change to another Camera that can be used with Your Mac (no there are no miniDV tape Cameras that can)
    • If Your Mac-Book has a PCM-CIA Card place - then there are FW-port-Cards and then
    You can import via this - but I've not seen this on more modern Macs. My PowerBook G4
    has one and this FW-Card-port works greatly.
    SoftWare
    • Delete iMovie pref. file may help sometimes. I rather start a new account, log into this and have a re-try.
    • Any strange Plug-ins into QuickTime as Perian etc ? Remove and try again.
    • FileVault is off ? (hopefully)
    • Screen Saver - OFF
    • Energy Saver - OFF
    Using WHAT versions ? .
    • Mac OS - X.5.4 ?
    • QuickTime version ? (This is the heart in both iMovie and FinalCut)
    • iMovie’08 (7.1.?), 09 or 11 ?
    • iMovie HD 6 (6.0.4/3) ?
    Other ways to import Your miniDV tape
    • Use another Camera. There where tape play-back stations from SONY
    but they costed about 2-4 times a normal miniDV Camera.
    • If Your Camera works on another Mac. Make an iMovie movie project here and move it
    over to Your Mac via an external hard disk.
    (HAS TO BE   Mac OS Extended   formatted - USB/DOS/FAT32/Mac OS Exchange WILL NOT DO)
    (Should be a FireWire one - USB/USB2 performs badly)
    from LKN 1935.
    Hi Bengt W, I tried it all, but nothing worked. Your answer has been helpful insofar as all the different trials led to the conclusion that there was something wrong with my iMovie software. I therefore threw everything away and reinstalled iMovie from the HD. After that the exportation of DV videos (there has not been any problem with HDV videos) to my Sony camcorders worked properly as it did before. Thank you. LKN 1935
    from Karsten.
    in addition to Bengt's excellent '9 yards of advice' ..
    camera set to 'Play' , not rec/computer/etc.?
    camera not on battery, but power-line?
    did your Mac 'recognize' this camera before...?
    a technical check.
    connect camera, on, playback, fw-connected...
    click on the Blue Apple, upper left of your screen ..
    choose 'About . . / More . .
    under Firewire.. what do you read . . ?
    More
    • FileVault - Secure that it’s turned off
    • Network storage - DOESN’T WORK
    • Where did You store/capture/import Your project ?
    External USB hard disk = Bad Choice / FireWire = Good
    If so it has to be Mac OS Extended formatted
    ----> UNIX/DOS/FAT32/Mac OS Exchange is NOT Working for VIDEO !
    mbolander
    Thanks for all your suggestions. What I learned is that I had a software problem. I had something called "Nikon Transfer" on my Mac that was recognizing my Canon camcorder as a still camera and was preventing iMovie from working properly. After un-installing Nikon Transfer and doing a reboot, everything worked great.
    I never liked the Nikon Transfer software anyway--I guess I'll get a cheap card reader and use that to transfer photos in the future.
    No Camera or bad import
    • USB hard disk
    • Network storage
    • File Vault is on
    jiggaman15dg wrote
    if you have adobe cs3 or 4 and have the adobe bridge on close that
    or no firewire will work
    see if that helps
    DJ1249 wrote
    The problem was the external backup hard drive that is connected, you need to disconnect the external drive before the mac can see the video camera.
    MaryBoog wrote
    Maybe your problems is solved in the meantime, but for all others this might help as I had the same problem, also have the Sony HDR-HC7, but the 7e (Europe, PAL). I found this link today and it works perfectly
    //support.sony-europe.com/tutorials/dime/videotransfer/vtransfer.aspx site=odw_en_GB&sec=DVH&m=HDR-HC7E
    What I exactly did.- put camera in play mode - open guide - choose connection guide - choose comp./printer (where to transfer movie to) - select connection.- i-link (on my camera) but equal to firewire - OK - choose HDV - choose NO for conversion of i.link.
    Settings are shown then (VCR HDV/DV.- HDV and i.link-conv..- OFF), press OK, OK, END.
    Switch camera off. Connect firewire cable to camera & Mac. Switch camera on, in play/edit mode.
    Open i-movie, choose import from camera. On screen below the camera connection is shown.- DV (HDV). Now you can import, automatically or manually.
    This worked perfectly for me. Took me 2 days to find out. Could not find any clear thread explaining what I had to do on the camera and the manual was not clear either.
    Yours Bengt W

  • DVI scan converter for under $1000?

    I've just gotten some e-mails which indicate DVI scan converters are downright expensive. Considering many DVI HD-TVs are now well under $1000, you'd think that you could get a scan converter for less. Sure there is DisplayConfigX and SwitchResX, but they are complicated to setup, and it appears not all HD-TVs respond well to them. So here's the question, anyone know of a simple DVI based scan converter that will reduce the picture so that all four sides of the screen which are overscanned on my set actually appear on my HD-TV? I don't want to have to step down to VGA just to do scan conversion. Right now the VGA scan converters are only $200 to $300 depending on where you look. Why some companies charge as much as $12,000 for DVI versions is beyond me!

    there are scan converters that do the simple job of converting a signal from 1 format to another then there are converters (scalers) that are designed to take NTSC (or PAL, SECAM, etc...) material and upconvert it to a higher resolution. back in the day when we used to deal with $50,000 9" gun CRT front projection systems, they often used $30,000 boxes that did the scan conversion. with CRT based systems on a large projection screen, you can actually see the black gap between the scan lines of the electron beams. the original reason to upscale NTSC video to different formats (differente VGA resolutions, really) was to increase brightness, not increase detail... for the higher the resolution, the smaller the black lines in between the scan lines on the screen. the reason that this is not so easy to accomplish is because film, which was originally shot in 24 frames per second, is being asked to play back on a device that is 60, 80, or higher frames per second (the vertical refresh rate). when dealing with film, you are of course dealing with people who are very critical with all technical processes being applied (rightfully so) and the same with the viewers. when done incorrectly or without proper processing, this scan rate conversion is visible by "rips" or jittery motion artifacts during playback.
    because more and more of today's modern sources are digital (DVI and HDMI) and the display devices are also digital (LCD, DLP, and plasma) scan converters and scalers are somewhat obsolete. it is still downright confusing, though. 1080i from an HD-DVD is played back at 1080p. 1080p from a Blue Ray player is played back at 1080p. HDMI, while supposed to make life simpler, actually has a whole list of incompatible sources and display devices with more HDMI #.# versions to come.
    i retract my statement, scan converters are no longer obsolete, they are just packaged with the display devices and sources so there is no market for them. a 480p DVD player with DVI out does not really give you a 480p output direct from the 480p MPEG stream. the video DSP takes the MPEG, internally outputs 480i, then the built in converter processes it back at 480p. seeing how these DVD players are very cheap, there no longer is a market for affordable scalers. you now have the all or nothing scenario where the only vendors alive rely on high end clients that want to pay for the best and not settle with what is bundled.
    anyways, some of the companies still in the business...
    Faroudja (recently bought by Meridian UK)
    DVDO
    Silicon Image
    Focus Enhancements (exiting / exited the market?)
    Snell and Wilcox
    gefen (is a newcomer beginning to offer some product)
    i'm sure that i'm missing a bunch, but these are the ones that i recall off the top of my head

  • What is the very best hd camcorder to use with imovie 11?

    What is the very best hd camcorder to use with imovie 11?

    Well, people are always complaining that their exported movies are not of high quality, but mine look great, and I only export at 720p. The orginal is shot at 1080 30p. Here are some examples.
    http://youtu.be/Vi9XieIcvl4
    http://youtu.be/o8fU9_V8Ky8
    http://youtu.be/wu2wyJ6ZWT8
    Above are links to my videos of my trip to Holland, Belgium, and Luxemburg.
    Be sure to view them at 720p on Youtune, or they will not look that good.
    The camera is the Canon HF s21.

  • 3CCD Cam for under $1000?

    I am looking for a good quality 3ccd camera under $1000. I've had my eye on the Panasonic PV-GS500. Any opinions on this camera or suggestions?

    I would recommend the Canon HV20. In my opinion there is nothing else in it's class that produces such a profession image.
    It is not 3 CCD but it is more sensitive to light than most of the 3CCD cameras in the category due to it's larger CCD. Most smaller CCD cameras use small 1/6 inch CCD's which basically add up to the same light gathering capability as a single 1/3 inch sensor.
    The image is very film-like in the 24P cinegamma mode. The Panasonic is good, but will not do 24P HD. The HV20 also has a CMOS sensor which responds to light in ways very similar to Canon's Digital SLR camera sensors. The knee to the highlights is very very smooth for a consumer camera and the cinema mode applies very little sharpening which I believe really helps reduce noise. I've been very impressed with the image quality next to our Panasonic Varicam footage and 35mm transfers. If you plan to do studio work, the HDMI out on the camera is completely uncompressed 10bit output at pure unstretched 1080P resolution. No downsampling or limited color space. This is huge for $1K camera. There is a $300 PCI express card from Blackmagic that captures this HDMI signal into ProResHQ. It also works with other formats and is really nice for the price.
    If you have still photo SLR cameras, you might consider a Cinevate Brevis 35mm adapter as well, since the limited depth of field is the true secret to making footage look like film. This makes up for the camera's biggest limitations such as poor manual focus and average wide angle coverage. You can rack focus with such lenses and use follow focus units without having to burn through film at $300/reel plus transfer fees. It only loses about 2/3 of light compared to most adapters that lose over 2 stops. A Canon 50mm 1.4 prime looks just like a true 50mm does through the viewfinder of a Canon SLR. This is a great addition and should be considered a standard must-have if you shoot footage that is supposed to look like film. A full kit for the HV20 is about $1K.

  • Best DVD camcorder ?

    Please advice me about the best DVD Camcorder to :
    1) it Gives a very good quality in Resolution and Colors,
    2) it has a good way to record and store the data on an economic level...
    3) Mac - Pc
    4) Other advantages...
    Many Thanks

    None of them do which was the point. They record in MPEG-2 which does not even have individual frames.
    Read up on how MPEG-2 compression works but suffice it to say it makes one keyframe (all the data) then a bunch of differential frames holding only what has changed from the keyframe, then a keyframe after say 30 frames.
    You don't have frame by frame editing as there are no frames other than one every 30 frames, say one per second.
    MPEG-2 is a "delivery" format, e.g. a DVD to view, not an editing format. DV or other high quality source is compressed (data is lost) to make the DVD which is supposed to be the final form. Not the starting point.
    All these DVD cam wonks (vendors) are doing a disservice to anyone who will not be happy with everything that is shot to the DVD as being acceptable as the end product.
    You may know that most raw video is horribly boring, long, dull, and badly shot and there might be 10 minutes of keeper stuff per hour shot. So the DVD people have these little 30 minute DVDs and the audience suffers with the 25 minutes of dreck that exists with the 5 worthwile minutes.
    New AVCHD may offer frame by frame HD MPEG-4 but right now even though Sony and others sell these cameras there is no software to edit the video. Not much value there quite yet.

  • Which Laptop for Photoshop + Web Design? (under 1000$)

    Hey there-
    I need a PC laptop and not sure which to buy. Just getting started with photoshop and web design but hope to make it a career. Money's tight so under 1000$ (max) is ideal. Do I need a dedicated graphics card, or is integrated okay? Intel or AMD? Screen resolution? I'm confused.
    Any tips are much appreciated, thanks!

    Do you really need a laptop?  You can get a lot more for the money with a desktop.  Many serious users use one or more 24+ inch monitors.
    Win7 is better than Win8.  The standard recommendation is a dedicated video card with 1 gig of VRAM, min. 2 internal HD or large SSD, and min. 8 gig of ram.

  • Best camcorder for $1000

    I'm going to be creating training videos for my company and have a grand to spend on a camcorder. Anyone extremely happy with theirs? I usually by Sony, but will listen to any ideas. Should I go HD? Do I need a cam with FireWire capibilities? Thanks for any help you can provide.
    Mitch

    OK...my impressions of the HV20.
    It is a CONSUMER camera...very much so. I know a lot of people are buying this, using it as the new DV REBEL camera...and that is because of the full raster 1920x1080 CMOS sensor inside. But that is about ALL it has to offer on its own. To get a decent image you need to spend another $1200 to $1500 to get a rig and lens to make this a decent camera (RedRock Micro, Letus 35 Extreme).
    Why?
    Because the FOCUS control is a joke. Not a ring, but a little wheel on the side of the camera. And adjusting that focus is painful...very hard to do. EXPOSURE controls? Well, sorta. You can dig a few out, and they are OK...but nothing compared to a good DV camera like the DVX-100b or even my Canon GL-1. I LOVE my GL-1...I felt crippled by the HV20. Sure, it is $1000, but to get a goot working image out of it that isn't consumer looking, you need to spend more money. NOW, that being said, I think with those pieces of equipment, making the camera total out at about $3000, it will be a good competitor to the Sony VU1, a $4000 camera.
    And to echo the Capt...unless you are going to show this on an HDTV, there really is no point to go HD for what you are doing. A good DV Camera will get you a better quality image.
    BUT...for $1000? The ONLY options you have are consumer cameras. So in that light the HV20 might bear looking at. But, lets look at ease of use...EDITING those formats, viewing and color correction.
    HDV is a tricky format. Capturing it might pose issues for some, and is pretty much straight forward. BUT, you are now using the GOP MPEG-2 format, and rendering takes longer, compressing takes longer...A LOT longer. Now, how about monitoring your footage for color correction.
    With DV you can hook up a camera to your TV, then to your computer and route a signal thru it...and use your TV or decent NTSC monitor. Bam...done. Not so with HDV. To view this on a TV to see what you have and for color correction, you need an HD capture card, and an HD monitor. So...MORE money than that $1000. Even to make it more easily editable as DVCPRO HD or ProRes, you need a capture card to capture and monitor that footage. DV is very straightforward and viewable right away.
    So...$1000 for a camera. Getting into HDV means more than that $1000 investment. Just as a warning.
    Shane

  • Looking for best compatible camcorder for Mac

    Which format is best duited for I movie and Macbook's in general. I want a mid level camcorder for vacations and family and would like ease of use for editing in I movie & other video editing programs with my new Macbook pro. Is Mini DV still the format of choice? What about SD flash?
    thanks

    Start your research here:
    iMovie 11 - cameras supported:
    http://help.apple.com/imovie/cameras/en/index.html?lang=en_US
    iMovie 9 - cameras supported:
    http://support.apple.com/kb/HT3290?viewlocale=en_US
    iMovie 8 Camcorders supported:
    http://support.apple.com/kb/HT1014
    Digital camera RAW formats supported by OS X Lion:
    http://support.apple.com/kb/HT4757?viewlocale=en_US
    Digital camera RAW formats supported by OS X Snow Leopard:
    http://support.apple.com/kb/HT3825?viewlocale=en_US

  • Best Monitor for Under $500

    I'm looking to pick up a new monitor for the office and I was given a budget of $500 to work with. Obviously, this excludes the best models available, but 
    I should still be able to find something decent. Any help is appreciated.
    Here are my requirements.
    1. Cost must be under $500
    2. Good color accuracy. I'm a graphic designer, so this is very important.
    3. 22" or bigger.
    4. 1920 x 1080 or better
    5. Wide viewing angle.
    6. Good contrast ratio
    7. Good overall sharpness. I do not want grainy whites.
    8. Glossy or matte screen is fine.
    More details
    1. Well lit office environment (fluorescent lighting).
    2. LED or LCD. Either option is fine. Looking for the best overall quality regardless of technology.
    3. Gaming performance / response time is not important. This will only be used for design work.
    Models under consideration
    1. HP 2310m
    2. Samsung SyncMaster F2380M (It seems to no longer available)
    3. HP 2311x
    4. HP ZR24W
    5. Dell UltraSharp U2410 (poor quality control)
    Are there any other good models that I am leaving out?

    I can only say that I have three F2380's (without the M) and even while they are not up to IPS monitors, they are way better than TN monitors, meet all the other requirements you stated and IMO they do deliver a very, very nice price / performance ratio.

  • Recommendation on the best HDV Camcorder to buy?

    I've just had my SONY TRV900 stolen and now need to purchase a new camcorder. I would like HDV, 3CCD and portability. I do some video work but don't need a full Ppr level camcorder yet. Can anyone recommend a good HDV camcorder with 3CCD and good quality output?

    3CCD's is a must. Otherwise, you get a lot of chroma crawl, lower resolution, impossible chroma keys... etc... Progressive video looks a lot more like film, and it plays nice on computer displays which are also progressive scan. freeze frames look better too.
    In reply to all here... if you can buy an HVX-200 instead... DO IT. Better picture, better post, better everything. Look of film is easily achieved with it too. NO capturing anymore either... backup on DVD's or FW drives if need be... it's a winner of a format, and just blows HDV out the door.
    About the only HDV camera that competes is the Canon and only when you capture out it's HD port during the shoot and capture that material as something other than HDV IMHO.
    The school I teach at part time, has 3 of these cameras, and abouty 6 HDV cameras, the students are fighting over the HVX's... they just work a ton better, and look a lot more like film. My favorite DV camera is the Panny 100a... this new HVX is it's big brother... same look, great balance to the camera, and all the manufacturers of the accessories of the 100a are implementing them for the HVX... It's the most exciting camera produced in the under 10k catagory in years I think.
    HDV is so slow in rendering and workflow in post that it's a no brainer if your time's worth anything to you. FCP 5.1.1 is better at it than FCP 5.0.4, but it's still about 5 times rendering time longer than the P2 material is... P2 is a true HD format, where HDV really isn't... If you don't have a VERY fast mac, the rendering time will simply make it no fun to work with. Quad PPC or dual duo at least I'd think.
    Prices are falling on this camera too now that there's a supply... check this: http://fotoconnection.com/vi-26412______Panasonic-AG-HVX200-1-3-quot;-.html?gclid=CJfZm6Omo4cCFTHTJAod8nhyJg
    Jerry

  • Best MiniDV camcorder

    I know this has been asked before and I've read the threads but please indulge me as I'm going to buy something new and would love a up to date check against the experienced users here before a final decision, have not fully decided whether to go HD, (if so considering the Canon HV-?) but would also like to consider a good standard def unit, analog to digital passthrough is a big plus to me, would love to hear peoples choices for the best of HD and SD in minidv format

    I have a Sony DCR-HC48 standard def camcorder and really like it. It does a pretty decent job at video, even in low light, can shoot widescreen, has a built-in lens cover, transfers via iLink/Firewire, and is small enough to put in a fanny pack at DisneyWorld (very important to me, since the best camcorder in the world doesn't do much good sitting on the desk at home!).
    I would definitely recommend it, although while I know it will play old analog 8mm videos I think that's the extent of the analog passthru. Not sure what you were looking for exactly (it will also play digital Hi8 tapes, for whatever that's worth)
    I also have the DCR-HC48. This camera does not have passthrough. It also cannot play the old 8mm videos. This camera is a miniDV camera only.
    I was disappointed that it did not have passthrough. I was replacing my old Sony DCR-HC30 which did have passthrough. That camera cannot take video any longer, but the passthrough still works.
    A lot of manufacturers, if not all, are putting most of the best features inthe newer format cameras. It may not be easy fining a miniDV with passthrough.
    Maybe Canons or Panasonic miniDVs have that feature.

  • What camcorder under $500 would you guys recommend?

    I'm about to have a baby in the next week or so, and I'd like to get a camcorder!
    What camcorder would you recommend to work well with the Mac lifestyle?
    I have an iMac 21" + apple TV, and I don't really need HD or anything - just good wquality widescreen footage would be nice to watch on AppleTV once I'm done editing in iMovie.
    Any suggestions?
    // Martin

    A miniDV tape cam will give you lossless quality video, as opposed to other formats that use high compression to store the video files. Definitely avoid any DVD cam, as DVD's are end products and they are not intended for editing purposes.
    Since you seem to be new to moviemaking, you may also not know that you can get a free download of iMovie HD6, the previous version of iMovie and many will say the last, best iMovie made. It offers greater editing capabilities and a pro style timeline editing format, as opposed to iMovie 08, which is geared towards the You Tube style moviemaker and has a very different workflow.
    If you do decide that HD6 offers more of what you want, you must only consider a miniDV cam with firewire, as iMovie HD6 will only capture from that format. Other format cams will require third party software, extra time and loss of quality in your final production, if you need to import non .dv files into HD6.
    Having a tape cam also allows you to always safely keep your original footage, plus make a tape copy of your finished movie by exporting from iMovie HD6 back to your cam. Tapes are far more reliable long term storage media, if stored properly, than any DVD or hard drive will ever be.
    Here's the link to the free HD6 download:
    http://www.apple.com/support/downloads/imovieHD6.html
    Here's a link to a camcorder review website to help you decide which way to go. Bear in mind that salespeople are going to direct you to what their store wants you to buy and with the glut of hard drive, flash memory and DVD cams out there, the best format, miniDV, is not getting its fair shake.
    http://www.camcorderinfo.com/
    Good luck giving birth next week MARTIN - you must be the world's first!!!

Maybe you are looking for