Blink the catridge led one by one in officejet 7000 wide format

When send the test page the printer become offline and the led of catridge is blink one by one.Please suggest to how to resolve it.

Hello , I may be able to help you with the blinking lights on your Officejet 7000 wide format printer. Using the Blinking Lights on the HP Officejet 7000 (E809a) document I found out that the light sequence you described is related to the printhead installation. To make it easier for I have copied the suggested steps here for you; Solution One: Check the printhead installation
Use the following steps to make sure the printhead is correctly installed.
Step one: Remove the printheadMake sure that the product is on.Lift the top cover. The carriage moves to the center of the product.
Figure : Open the top cover
Wait until the carriage is idle and silent.Disconnect the power cord from the back of the product.Remove the cartridges. Press the tab on each cartridge, and then remove each cartridge from its slot.
NOTE:Do not leave the cartridges outside the product longer than 30 minutes. Doing so can result in damage to both the product and the cartridges.Lift the latch handle on the carriage until it stops.
Figure : Lift the latch handle
Lift the printhead straight up to remove it.
Figure : Remove the printhead
Step two: Reinstall the printhead
Reinsert the printhead. Make sure the green and purple blocks on the sides of the printhead align with the corresponding color blocks on the carriage; green to green, purple to purple.
Figure : Insert the printhead
Carefully lower the latch handle before reinserting the cartridges.
NOTE:Leaving the latch handle raised can result in incorrectly seated cartridges and printing issues. The latch must remain down to correctly install the cartridges.Figure : Lower the latch handle
Reinstall the cartridges. Using the colored shape icons for help, slide the cartridges into their appropriate slots until they snap into place and are seated firmly in the slot.Close the top cover.Try printing again. You could also try the steps in 'Printhead Problem' or 'Printhead Appears to be Missing or Damaged' Displays for HP Officejet 7000 Wide Format Printers. If the issue continues, I would Contact HP Support for further assistance. Fill in the model number and the form to receive a case number. You can view all other ways of contacting HP from their list of Support Options. Please let me know if any of these steps resolved your issue, or if there is anything else I can do to help. Thanks,

Similar Messages

HP Officejet 7000 Wide Format Printer Series Error "ALL LIGHTS ARE BLINKING?"

What are the causes of my printer HP Officejet 7000 Wide Format had this error "all lights blinking"? Which part of my printer have a problem? please help!! thankzzzz......

Hello ryigo24,
Welcome to the HP Forums.
I see that you are having an issue with all the lights blinking on the printer.
Please click on the following link that deals with Blinking Lights.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Toshiba Tecra A7 don´t "power on" only blink the batery led 10 times

Please help
Toshiba Tecra A7 don´t "power on" only blink the batery led 10 times
Thanks
Xavier
[email protected]

Can you check the laptop's full model and part numbers from the label on the bottom? Don't include the serial number.
Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections.
- Peter

HP Officejet 7500A Wide Format e-All-in-One Printer - E910a

HP Officejet 7500A Wide Format e-All-in-One Printer - E910 scaner & copy not workser:-MY4C8510F9

Hello bondcip ,
Welcome to the HP Forums.
I see that you are having an issue when attempting to Print on A3 paper.
What program are you printing from? Does this happen with Microsoft word or emails?
Run the HP Print and Scan Doctor and let me know if it finds any errors and what they are.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP Officejet 7500A Wide Format - Can't reset the paper size - won't print!!!

I have a new HP Officejet 7500A Wide Format All-in-one printer. I love it and have had no problems with it...until now. The other day I went into Photoshop and printed a 4x6 photo and now my printer will not allow me to print on 8.5X11. I have checked the paper size in Photoshop, Word, Excel, Acrobat...everything I used that day, but it all shows "letter" size paper in the properties. I also checked the printer utilities...letter size paper is selected.
But when I try to print, the printer and the computer both give me a "paper mismatch" error and my only option is to change the paper or cancel. I went back into photoshop again and was able to print a 4x6 photo again - once I put in 4x6 paper - but then I changed it back to an 8.5X11 size photo sheet and tried to print on letter size paper and..."paper mismatch'.
I changed the printer back to factory settings. Nothing. I just had to reset up my printer on my network, but it still won't print. I tried to re-install the printer software from the installation disk, but it won't install. It says "already installed".
HELP!!!!!! I honestly don't know what to do at this point!!!!!
Thanks in advance!!

I have struggled with a similer problem with my new 7500A. I've done all the things you did. I made sure I had all updates and the firm ware update. I spent time on the phone with a lady who meant well but clearly didn't know the product. I had a difficult time communicating with her. Her accent was in the way. This morning I realy didn't want to face another day of this struggle. As I walked into my studio I had a idea. Instead of going to the computer to try to solve my problem through menues, HP Customer Service and or communities. I went dirrectly to the printer. I turned the printer on, the little screen on the printer lit up I touched the arrow to go to the next screen of menus. I touched "Set Up" then scrolled down through the choices. I picked "Preferences". At the bottom of the list was.............. Media Width/Type Sensing (ON)............I promptly turned it (OFF) ......................I am printing as I was told I would be able to do prior to buying. I am not getting that anoying screen "Paper Mismatch" . The printer is printing now on my 12 x 12 stock regardless of the type. ie: cardstock, plain paper, colored paper, construction paper. I hope this helps some of you out there. Clearly HP was of "NO" help to me. I have read that others are installing HP 7000 drivers etc. I've solved the problem without going to those lengths, no thanks to HP.

Officejet HP7500A Wide Format All-in-One Printer

The right side of the touch pad does not respond.

The right side of the touch pad does not respond.

How do i stop all the apps from printing on my officejet 7500a wide format?

I want to stop all the apps, like free samples, from printing! They have used up too much of my paper and ink!!!

Hi,
Please use the following link (under "Manage Print Apps" to cancel/remove it:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02940901&cc=us&dlc=en&lc=en&product=5058336&tmp...
You may also get this:
My Print Apps
To view and manage print apps for your printer, use the display on the printer itself. This website cannot manage print apps for your printer. In this case, you have to cancel from your printer.
Please also try this (if needed):
http://h10025.www1.hp.com/ewfrf/wc/clc?tmp_showAll=false&destPage=document&cc=us&dlc=en&docname=c031...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Want to initiate all the LEDS one by one in VI

Hi,
In the attached VI I am controlling the LEDs on the front panel by selecting values of different enums values on clusters, Now I want to lit all the LEDs one by one by only selecting and sumbit only one LED through cluster from front panel.
For example:
If I am selecting
1TRK
ENA
Green
then first LED 1ENA_DG will glow green only but now I want to control two more LEDs i.e. 1ENA_HG and 1WSA_RG in a sequenece after 1ENA_DG
If more clarofication is required please let me know.
Thanks
Prashant
Attachments:
WIU-SIGNAL-ASPECT-SEQUENCE.vi ‏102 KB
DAQsignalAspect (SubVI).vi ‏112 KB

Hi,
What are those in the pink boxes. What is the function name? Can I use that in labview 2011?
The pink boxes are I/O Nodes (FPGA) and you need to have an LabVIEW FPGA module installed, in order to run the example, however with this example I just wanted to show you a possible way to light up the LEDs on your board by placing a boolean pattern within a case structure that has LED addresses as possible cases.
Also suggest for blinking LEDS I have some blinking LEDs which will be controlled by the sloid LEDs.
To make an LED blink you can use a Property Node. Right Click on an LED in your block diagram and select Create->Property Node -> Blinking. You can change the Property Node to Write and wire a True constant to the Blinking Property Node. Now to trigger blinking of one LED by another LED you can simply place a Property Node of a blinking LED in a case structure and wire the conditional input of a case structure to the boolean state of the solid LED. Refer to the example below.
Mikhail
RF Toolkits, Product Support Engineer
National Instruments
Attachments:
led.vi ‏6 KB

My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

My brand new MacBook Pro retina display not charging the battery any more after 3 weeks...no green or red Led. Any one now about this problem? Thanks

Either the power brick is damaged, or the charging circuit is on the blink, or both. Either way, a trip to the Apple Store or the Apple Authorized Service Provider is in order, as this ain't no bargain basement toy.
In the meantime, can attempt an SMC Reset to see if it helps.

TS3218 My iPod Nano 6th generation fell one time and it kept working with a small crack in the screen.But after a while it just gave out and does not turn on.I try to charge it and all it does is blink the apple icon on and off.When disconnected nothing h

My iPod Nano 6th generation fell one time and it kept working with a small crack in the screen.But after a while it just gave out and does not turn on.I try to charge it and all it does is blink the apple icon on and off.When disconnected nothing happens.

I am having the identical trouble as described above with my month old Macbook Air. I tried everything with the ditto results. Please help anyone!
Mine is a Macbook Air 13', 128GB, 1.86GHz with 4 GB RAM.

Can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

Yes. Any standalone display which can be connected to a Mini DisplayPort, with or without an adapter, can be plugged into a Thunderbolt port without any additional adapters.
(65766)

My one month old macbool pro shut down unexpectedly and is not starting up the magsafe led is faint orange and flickering what to do now???will I be charged by apple istore ??? I'm very panicked please reply

My one month old macbool pro shut down unexpectedly and is not starting up the magsafe led is faint orange and flickering what to do now???will I be charged by apple istore ??? I'm very panicked please reply

Welcome to Apple Support Communities
It seems like your logic board is damaged. As your computer is in warranty, you will get your MacBook repaired for free if you take it to an Apple Store or reseller. Furthermore, you may receive a new MacBook

T400 Hangs Surfing or Working on WiFi Network and the Wifi Led stops Blinking !!!

I have a T400 Model (2764CTO) - with 5300 AGN, 2.53 Ghz, 3 Gigs RAM.
I have been facing a wiered problem - my machine hangs - all of a sudden - and at the times - after the machine has hung - the WiFi Led - goes off. I have searched and installed PC Doctor for Lenovo - and it does not capture the Hang Event. The only option I have left is a Hard Re-Boot.
Can any one please help. I have updated my LAN Drivers and WiFi Drivers - and still dun know what cud be causing this issue !!!

Hi drpiso,
Thanks for the question. Based on what you stated, it seems like the computer is the only device having trouble connecting only to your home network. I would recommend that you read this article, it may be able to help the issue.
iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support
Thanks for using Apple Support Communities.
Cheers,
Mario

Purchased Complete Led Zeppelin, all one album

Is there an easy way to make the Complete Led Zeppelin Show up as all the individual albums rather than one big one? It makes it much harder to sort and search for a particular song. Also, not having all that artwork available for my apple TV is upsetting. Do I manually have to separate them all?
And if I separate them will the iTunes Store download the appropriate album art for me?
Thanks

If it comes from iTunes packaged as one album with one piece of artwork, I think you'll have to do the following to achieve what you want.
-- Troll the Web (amazon.com is a good resource) and find the individual art you need for the albums represented in the package. Paste into the artwork tab on the appropriate tracks.
-- Change the info on the tags for tracks to ID them as individual albums. This would include changing the track numbers, album name, etc.
Not an easy fix, but doable. I wouldn't be too upset though. It was purchased as a single album, so that's the way it's ID's and packaged.

HT204053 The entire family has used one itunes account for years. How do we all set up separate iCloud accounts now?

The entire family has used one itunes account for years. How do we all set up separate iCloud accounts now? Or should we? 5 macbooks, 2 ipads, 4 iphones, 2 itouch, 2 imacs. How does one decide what to sync, share and what not to? Green Jeans.

You need to start by understanding the distinction between iTunes and iCloud - Apple confuse the issue by referring to 'iTunes Match' as part of iCloud. It isn't.
You don't have to have the same login (Apple ID) for iTunes and iCloud; many people don't and there's no problem about it.
Your iCloud ID gets you email, calendars, contacts, iWork documents and PhotoStream syncing between devices.
Your iTunes ID gets you the iTunes Store, the App Store for iOS, the Mac App Store for OSX,, 'iTunes in the Cloud' (downloading of purchased items to any logged-in device) and 'iTunes Match' (uploading of songs not purchased in the iTunes Store).
Your family members can easily each get their own iCloud account to keep email etc. separate - in each case they will need a different non-Apple email address (a free one from Yahoo etc. would do) to set up the ID. If they are sharing a Mac they need to be using a separate user account.
They can have their own iCloud accounts and still all sign into the same iTunes account: or they can open their own iTunes accounts using their new iCloud Apple IDs.
BUT they cannot transfer items purchased under the present iTunes ID to different iTunes IDs.

Blink the catridge led one by one in officejet 7000 wide format

Similar Messages

Maybe you are looking for