Boot Failure - Partially Fixed

On the weekend I installed a new program on my Mac mini. Later as the mini was being shut down the power went out. This led to many problems.
When I tried to boot up the next time the system just hung with a grey screen, apple logo and spinning wheel. Then the screen went blue after a while and nothing. I tried many things like resetting the PRAM, booting in verbose mode, and the Disk Utility on the install disk.
The disk utility told me after 3 tries that it could not repair the volume.
I then tried to partion the drive hoping to keep my old files. No luck, I ended up reinstalling OS X (Tiger). Then I reinstalled a second time when I removed the partition.
Now I am trying to use my old G4 cube to transfer my old files to the mini via Firewire target mode. It worked last time but when I do it now the cube is telling me it does not recognize the volume that is hooked up.
What should I do?
Here are my thoughts.
1. Should I run the disk utility on the mini to make sure everything is okay.
2. I only have one key board and monitor so I boot up the mini until I see the fire wire symbol. Then I unplug the monitor and keyboard and put them on the cube. Might not be the right thing to do.
Any thoughts on getting target mode to work would be great.
Finally going forward, should I be making regular copies of the disk image and storing them on my external hard drive. This I assume is a definite yes.
Thanks for any advice.
Cheers,
JOxl
Mac Mini -Dual Core Mac OS X (10.4.7)

You may have done this already....have you booted from your OS X DVD, then thru the utility menu loaded Disk Utility, to repair the disk? You can't repair the disk if you load Disk Utility from the volume you want to repair.

Similar Messages

Windows 7 Ultimate x64 BOOT Failure on HP ProBook 450 G1...

Dear forum viewes and experts...
I hope you can provide me with your insights on this problem i am having...
I bought a new laptop HP ProBook 450 G1 (i5 4200M, 8GB RAM, 1TB HDD, 2GB ATI Graphics card). The laptop comes with DOS free operating system.
I installed Windows 7 Ultimate from ISO file on a USB stick, and then activated the Windows.
After updating all drivers and having a clean device manager with no hardware left as unknown, i figured out that the laptop fails to make a cold BOOT.
After several trials, and installations. the problem remained the same. I changed the installation to Windows 8.1 Pro and the problem remained the same.
On cold booting, the laptop after showing HP logo in start-up starts to show Windows Logo animation but in Super Slow Motion for about 6-8 minutes, then followed by strange sounds which force me to shut it down by pressing power button for long until it shuts down.
After huge number of trail and error, i found out that if I entered BIOS Setup (by pressing esc then F10) and then exiting it without doing any changes or even without saving, the Laptop boots Windows 7 very smoothly (in about 15-18 seconds) and works fine. it also can make endless number of smooth restarts without any problem.
If it is shut down then turned on, the boot failure is the outcome.
The only way to make a successful cold BOOT (i.e after a shut down) is to enter BIOS setup mode (by pressing esc then F10), then exiting it within seconds without changing anything or saving, then it boots smoothly.
I tried MBR fixes through command prompt in Recovery Mode, I tried to change booting to make it boot as LEGACY or UEFI Hybrid. The BIOS is updated to the latest frimware on HP website verion 1.2 dated 15 July 2014.
NO HELP.....All lead to the same disappointing result.
Any idea whether this is a hardware issue/software issue/BIOS issue?
Your insights will be highly appreciated

Hello,
I'd ask in the
Windows 7 forum on Microsoft Community.
As the Microsoft Community is on a different platform, we cannot move the question for you.
Once there, click on Participate near the top of the screen, and select 'Ask a Question' or 'Start a Discussion':
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book:
Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C406F75746C6F6F6B2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

HP Probook 450 G1 Boot Failure....!!

Dear forum viewes and experts...
I hope you can provide me with your insights on this problem i am having...
I bought a new laptop HP ProBook 450 G1 (i5 4200M, 8GB RAM, 1TB HDD, 2GB ATI Graphics card). The laptop comes with DOS free operating system.
I installed Windows 7 Ultimate from ISO file on a USB stick, and then activated the Windows.
After updating all drivers and having a clean device manager with no hardware left as unknown, i figured out that the laptop fails to make a cold BOOT.
After several trials, and installations. the problem remained the same. I changed the installation to Windows 8.1 Pro and the problem remained the same.
On cold booting, the laptop after showing HP logo in start-up starts to show Windows Logo animation but in Super Slow Motion for about 6-8 minutes, then followed by strange sounds which force me to shut it down by pressing power button for long until it shuts down.
After huge number of trail and error, i found out that if I entered BIOS Setup (by pressing esc then F10) and then exiting it without doing any changes or even without saving, the Laptop boots Windows 7 very smoothly (in about 15-18 seconds) and works fine. it also can make endless number of smooth restarts without any problem.
If it is shut down then turned on, the boot failure is the outcome.
The only way to make a successful cold BOOT (i.e after a shut down) is to enter BIOS setup mode (by pressing esc then F10), then exiting it within seconds without changing anything or saving, then it boots smoothly.
I tried MBR fixes through command prompt in Recovery Mode, I tried to change booting to make it boot as LEGACY or UEFI Hybrid. The BIOS is updated to the latest frimware on HP website verion 1.2 dated 15 July 2014.
NO HELP.....All lead to the same disappointing result.
Any idea whether this is a hardware issue/software issue/BIOS issue?
Your insights will be highly appreciated

Can you post a screenshot with the PCI\VEN hardware ids of the bluetooth device? The image below shows an example of what we need to identify the device properly.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Yoga 2 Pro: boot failure and touchscreen unresponsive

I've had my Yoga 2 for about a week and a half and for the most part I love it. First problem has been occasional (maybe 4-5 times) "Boot Failure", or something along those lines, on startup. Every time after restarting it it has worked fine. Also just earlier today I had a problem where the touchscreen went unresponsive for around 20 minutes before working fine again. I was in class so didn't do anything to try to fix it (taking notes so couldn't restart or anything), and it just starting working again by itself. Other than this, I have had no other problems. I have a few days left on my return/exchange with Best Buy, so wondering if these are problems that I should be seriously concerned about. Thanks.

If it were me, I would definitely exchange it. Boot failure may indicate some permanent failure about to happen, not to mention a flakey touch screen. Neither sounds like a software issue on a brand new computer.

Boot failure: Digital signature not found

Just bought a Toshiba Satellite C885D-S5320 and it was working great. Packed it up this morning, unpacked it a few seconds later and tried to turn it on. Got a message that reads "Boot failure: a proper digital signature was not found. One of the files on the selected boot device was rejected by the Secure Boot feature."
I didn't make a recovery disk but tried to use the hidden recovery feature I'd found out here. Worked great to abou 76%, then that message came up again. Help???

Re: SATELLITE C855D-S5320 Help me please!
Options
‎05-09-2013 04:32 PM
I bought the same computer from Walmart for my daughter for Christmas. I have had to send it in three times to have the hard drive fixed as it showed the same error that you were getting. I was very mad as the first time I had to pay $25 to have them ship me the box to send it in to them. I also tried at first to return it back to Walmart but was told it was to late and I would have to go through Toshiba. I just received it back again today. They have had to replace the hard drive three times. This is ridiculous as I have had several other computers and laptops and have never had to have a hard drive replaced before. I told them I was not paying the last two times to send it in for repair as it should never of had to go to them the first time. The girl did send me the box free the last two times but honestly I think they should just give me a whole new computer as I think these ones are lemons! I cannot believe a brand new computer would need to have a hard drive replaced 3 times in 5 months! The girl advised me if it had to go back again they would probably finally do something. I sure hope your is working better then mine.

Sudden total boot failure. Any idea what would cause this??

Today I was adding more apps to my clean install (on an external drive) and I had to go back to my original "update" installation to get a password off Keychain (I did not migrate). After I got the pw, I shutdown and my Powerbook would not reboot! I got the chime and then utter blackness. No disk access was attempted on my external, nothing from internal drive, and still nothing when I tried the Leopard installation DVD.
I kept trying and finally (after 10-15 minutes of getting nothing except the initial startup sound) the screen lit up and I got to the Startup Manager disk selection. I was still unable to boot from the DVD; the boot sequence had progressed only part way and then totally stalled (I gave it about 3 times as long as it would normally take to boot from a CD or DVD). I tried this twice more so I thought I had suffered catastrophic hardware failure.
But, then, after a pram reset, I was able to restart into single-user mode and did a couple of the fsck's (file-system check in Unix) and it said the internal disk was OK both times. Got through login and to the Finder Desktop after a regular boot, and after a safe boot, but found that the Finder was corrupted and repeatedly crashed with almost everything I tried to do.
Reluctantly then tried to boot from external drive and found that - it worked!
Tried to fix internal drive unsuccessfully. Eventually found that DVD drive was working again too, so I did a Time Machine restore of the internal drive after booting from the Leopard install disk.
After getting the internal drive to boot again (Time Machine worked!!), the Wacom tablet driver immediately crashed (even though I had supposedly loaded a Leopard-compatible version), so I then went to Terminal and got rid of all the StartupItems and PreferencePanes in the root Library and my user Library. I tried rebooting and since it did so without issue this time, I hooked up Time Machine and made a new backup.
How did the total boot failure get caused? I had never seen anything like this before where the screen stayed totally black and not even the DVD would boot.
I am now back to "normal" after 7 hours. Moral of the story is that even when your computer looks completely dead, keep trying. I just hope it doesn't happen again, since I'm not sure what the issue was.

Faulty battery. Make Genius reservation and take this iPhone back.

Boot Failure Issues

Thanks for any help that may come of this question. I'm not very fluent in the technical nitt gritty of computer hardware/software, but I've been using computers for years and I catch on quick. This goes for the "boot" problem I am getting.
My sytem crashed the other day after the northbridge cooling fan failed. I just finished replacing my northbridge cooling fan with a Vantec Iceberg and I tried to start up the computer. I did have to partially remove the motherboard to do this, so I had to disconnect several cables include the hard drive. I do believe, however, that all cbale s have been properly reconnected. When I power up, I see the color MSI logo pop up, it then appears to start "booting up", or whatever the next process is called. In doing so it gets to a point where it says:
Client Mac Add 00 0C 7615 4C E6
No Boot filename received
Disk boot failure, insert system disk and press enter
Not knowing what to do, I found a floppy MSI Bios Update Disk that I had made at some point and inserted this ( a mistake perhaps?) It flashed the bios, finished its work, and the problem still persisted. At one point I was able to get into a screen that appeared to show a boot order, and it had the CD ROM, another drive (forget which one), and LAN. But I did not see the hard drive listed. Am I correct in assuming that the issue is that the motherboard is trying to boot up the sytem, which it would normally do from the hard drive, however it cannot locate it?
I have started the process of searching these forums, and I found one that seemed to have the same issue but I had a little trouble understanding what they were getting at. Any help that can be offered would be greatly appreciated.

Quote from: swat148 on 19-October-06, 06:10:38
BOS, thanks for the help. The corrective action wasn't quite what you outlined, so hopefully you'll read this and just confirm that my actions were okay. I entered into a screen (forgot how I got there, F8?) that dealt with arrays. What is an arrary and what is the significance? One of the boot messages had mentioned that there was no array defined. So in this screen I defined the 1 array as my hard drive. And that was it. After that the system would load into windows? Was this a correct action to take? Because the BIOS had my HDD0 as the first boot source, but the error still persisted till I defined an array.
Also you asked me what the temp was. I don't know how to locate a temp specific to the northbridge chip. My PCAlert 4 shows a CPU temp of 50C and the system temp is 39C.
Also, in the manual for the motherboard, I noticed a FAQ that said you shouldn't connect a Vantec fan directly to motherboard because it draws to much power. So I connected right the PSU. This however, prevents PCAlert4 from being able to monitor its speed. Is this a problem? Is there a way around it?
Last thing, regarding my post to the fan thread, do you see a problem with the fan only set up on the chip?
Again, thanks for all the help.
"BOS, thanks for the help. The corrective action wasn't quite what you outlined, so hopefully you'll read this and just confirm that my actions were okay. I entered into a screen (forgot how I got there, F8?) that dealt with arrays. What is an arrary and what is the significance? One of the boot messages had mentioned that there was no array defined."
yep thats other possiblities, for some reason your fastrack was lost array and need to be reconfigured. after seening the message: "No array defined" you should press "CTRL+F" to entire in a utility and to re-setuped like you already do. you have done correct.as boot priority HDD0 or SCSI.
"What is an arrary and what is the significance?"
SATA disk on your mainboard will be recognised only when its defined in array via Onboard Promise Controller.
"Also you asked me what the temp was. I don't know how to locate a temp specific to the northbridge chip. My PCAlert 4 shows a CPU temp of 50C and the system temp is 39C."
you can use Everest to observe it: (https://forum-en.msi.com/index.php?topic=100852.0) Example:
"Also, in the manual for the motherboard, I noticed a FAQ that said you shouldn't connect a Vantec fan directly to motherboard because it draws to much power. So I connected right the PSU. This however, prevents PCAlert4 from being able to monitor its speed. Is this a problem? Is there a way around it?"
that is the correct way. no FAN RPM monitoring is not problem. you have done best.
"Last thing, regarding my post to the fan thread, do you see a problem with the fan only set up on the chip?
Again, thanks for all the help."
nope should be fine if NB temp remain acceptable, if temeperature is normal. but with other copper vantec base should be lowest. basicly if your NB temp is good/low there is nothink to worry.
you are welcome mate.

MSI 865pe neo 2 - BOOT FAILURE PROBLEM

i have a msi 865pe neo 2 motherboard and im getting the following problem, when i turn on my pc it is coming up with boot failure message and ask me to restart my computer it goes through this a lot then all of a sudden it works fine , when this problem happens and i go into cmos settings i notice that it is not reconising my IDE hard drive PLEASE PLEASE can someone help me with this and tell me what the cause is and how to fix it.
Many Thanks
Simon Rogers

im sorry here is the spec of my machine, and the problem is listed in my original post please can someone help
Motherboard - MSI 865pe Neo 2
CPU - Intel Pentium 4 2.8 GHZ Prescott
Hard Drive - Maxtor 6E040L0
Memory - x2 512mb Crucial DDR PC3200
Graphics card - Nvidia GeForce Ti 4600
Sound card - Creative labs live 128
CyberDrv CW038D CD-R/RW
Sony DVD RW DW-G120A
PSU 400 watt

System boot failure after upgrade from linux3.13.8-1 to linux3.14.6-1

I have tried to update the kernel again from 3.13 to 3.14 again, but no luck.
My arch system boot failure with black screen, tried [ctrl]+[alt]+[F1-6] and nothing happen, no any recure shell prompt out.
Then I boot with kernel debug parameters
systemd.log_level=debug systemd.log_target=kmsg log_buf_len=1M
althrough the screen was black, when I reboot and chroot into my system,
I entered the following to find any error messages, please see the link below:
journalctl -b -0 >> ~/3.13_no_problem.log
journalctl -b -1 >> ~/3.14-6_nodebug.log
journalctl -b -2 >> ~/3.14-6_debug.log
3.13_no_problem.log: http://pastebin.com/EQ2Mucq8
3.14-6_nodebug.log: http://pastebin.com/18TRZVRp
3.14-6_debug.log: http://pastebin.com/0QZJBPnf
In both 3.14 journal messages, I found some similar error message:
Jun 15 14:37:47 arch-desktop kernel: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting
Jun 15 14:37:47 arch-desktop kernel: [drm:atom_execute_table_locked] *ERROR* atombios stuck executing D218 (len 62, WS 0, PS 0) @ 0xD234
Jun 15 14:37:55 arch-desktop kernel: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting
Jun 15 14:37:55 arch-desktop kernel: [drm:atom_execute_table_locked] *ERROR* atombios stuck executing D218 (len 62, WS 0, PS 0) @ 0xD234
Jun 15 14:38:00 arch-desktop kernel: [drm:cypress_dpm_set_power_state] *ERROR* rv770_restrict_performance_levels_before_switch failed
Jun 15 14:38:01 arch-desktop kernel: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting
Jun 15 14:38:01 arch-desktop kernel: [drm:atom_execute_table_locked] *ERROR* atombios stuck executing D218 (len 62, WS 0, PS 0) @ 0xD234
Jun 15 14:38:07 arch-desktop kernel: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting
Jun 15 14:38:07 arch-desktop kernel: [drm:atom_execute_table_locked] *ERROR* atombios stuck executing D218 (len 62, WS 0, PS 0) @ 0xD234
Jun 15 14:38:13 arch-desktop kernel: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting
Jun 15 14:38:13 arch-desktop kernel: [drm:atom_execute_table_locked] *ERROR* atombios stuck executing D218 (len 62, WS 0, PS 0) @ 0xD234
I searched on internet, I think this is caused by my graphic card(ATI 5750), but I have no idea to solve it
I don't know my system boot failure due to these error or another things.
my PC specs:
motherbroad - gigabyte GA-P55A-UD3 (bios ver - F11)
cpu - i5-750
display - ati 5750
os - arch 64bit
Currently, I have downgraded back to 3.13.
I hope someone can give me some idea,
Thanks
Last edited by samtai (2014-06-17 12:17:02)

As there are errors associated with ntpd, I would temporarily disable the ntpd service and also ipv6.
If they are not the only problem, at least your logs would be easier to examine for other problems.

Failure to fix my cable for over a year and a half! HELP!

Failure to fix my cable for over a year and a half! HELP!
I regretfully have to inform you that I might have to discontinue using Comcast, for the following reasons if I cannot et you to resolve these issues. It should be noted that this is something that I do not want to have to do. However, basically I have no choice.
1. Repeated and Constant Internet Issues and Poor TV Quality for over a year.
2. A substandard quality of service, just even compared to my next door neighbors who has Comcast. The service has issues daily. Not a week has gone bye without an issue either small or large.
3. Constant and repeated interrupt of service and an overall low quality of product. Time Outs, High Ping rates into the 100s and 200s, Cable Light Off, Poor Quality of TV picture, fuzzy, Digital Blocking even on non-digital channels with or without box, Occasional CB Radio chatter over interment connection <-(the odd one).
4. The constant run around from the employee’s at Comcast and Service Department who either are unable to fix my problem, or unwilling to fix my problem, or have no one qualified to fix the problem. The amount of service calls and tech support personal I have had come to my house and had to call is so numerous I cannot even recall the amount.
5. Paying full price for a substandard quality and product while others around me do not have too. Including my next door neighbor which does not seem to have an issue.
The Story-
I purchased this house over a year and a half ago. Note; I did think it was odd that the pervious owner of this house had Comcast TV, but a DSL internet connection (I know now why he had to do that). In a brief conversation with him recently when he was visiting our next door neighbors he told me of how he had the same issues and had to switch to DSL.
I am, and always have been an avid Cable user and in particular for the Internet as the Broadband just makes it so much more enjoyable. I used Time Warner Cable for over 7-years prior to “having to” use Comcast with great service and good connection and a highly enjoyable time over the internet playing games and surfing the web. I have to use the words :“having too”, as you are the only Broad Band Internet connection in my area currently (I moved to the Burbs, not the Boonies) so I still don’t understand why my choices are limited. Must be nice to have a Monopoly though. : ), and I am starting to think this maybe part of my problems and why nothing is being done.
In any case, my internet use is for entertainment only. Surfing the Web, playing video games, Online Classes, and whatnot. Nothing life treating, or a must have service and basically, fun for the family, not for frustration. I like to use Cable as I never have to worry about the line cutting out or losing connection. This used to be the case, but with Comcast I do have to worry about this, and it happens often. Simply put: it is NOT always ON as advertised, at least for me.
The Issues-
From day one, I have had nothing but repeated and constant issues with my internet service. I don’t even think I had Comcast a week before I had to make my fist service call. See I was used to another Cable service and silly me expected my cable to work. From there it was all downhill. I have had so many service calls its actually outlandish and would be funny if it was someone else. Its like a TV sitcom actually.
Each and every service call goes the same way. Tech comes out, stands around, recognizes the problem and leaves. No fixes mind you, and the reasons are below.
Recent History-
With the internet on the fritz again and only seeming to get worse I decided to call and have someone come out and check it. A preemptive strike on my part in other words, before it totally blew out like it does and taking days for it to come back on. I have been dealing with this for over a year getting kind of frustrated with the whole process.
I talk to the service department and they also see the issue (sporadic interrupt of service and poor quality). With so many problems and the list ever growing most likely on my report the service guy said he would send a Line Tech out to check my problem on Monday (the ninth).
I think to myself finally some progress and it only took a year, a real Line Tech my issue is sure to be solved.
Unfortunately, the apparent Line Tech does and did the same as every other tech sent to the house. Set around for 20 or so minutes futzing around with the computer. Notes the issue of single loss and poor TV quality makes some notes and says sign here. *take note of paragraph below about Line Tech.
Around Thursday, I call up the service department basically asking if and when my service problems will be fixed. With little shock and surprise I was told that nothing is scheduled the last service call the Line Tech was not really a Line Tech and I should have been called back and or at least informed of that a Line Tech was not scheduled to be sent. This is normal by the way.
The Phone Tech checked my service and found that an issue did exist and proceeded to tell my that he would advise his supervisor of the issue. He also stated that if someone had not called me by 6:00PM this coming Saturday, that I could call and he would expedite matters.
Tick-Tock-Tick-Tock-Tick-Tock-Tick-Tock
Saturday at 6:20PM I call up the service department, punch in my phone number and low and behold I’m sent immediately to the Clams Department instead of the Service Department LOL.
After explaining the issue to the Clams Department (my thinking is at this point is; why pay for it if its not working and they wont fix it) I am transferred to the Service Department after a brief expiation of the issue. I guess I am a little late with my bill, but can you blame me?
The Run Around-
Talking to a new service persona again which is the same with ever tech sent to the house (Never the same one twice). Apparently nothing is on my report about this call I made earlier, or he does not note it.
The new service tech while helpful and curious taking the brunt of my frustrations at this point goes through the same procedures that I have been through so many times now I know them by hart. I acknowledge the fact ahead of time to myself that my tone although frustrated is nothing personal, and the service tech should not take it personally. Its just that at this point I’m beyond frustrated. I try to be as understanding and curious as I can while he tries to help me.
I explain the repeated problems and what is going on. In this instants the service tech mentions something about some service package (come kind of other signal maybe being sent to the modem).
At the time my internet is somewhat working with only a few time outs and just above normal pings so I cant really blame him for not seeing an issue. I’m mainly calling just to find out why I didn’t receive a phone call, or get another appointment to have this checked into.
My service was cutting out right before I called, which is why I called. The service tech just happened to check my service while it was working for 20 or so minutes. : P
Although, I am sure the Tech knew what he was doing and seemed very knowledgeable and probably thought he had resolved an issue that has been plaguing me for over a year now I knew nothing had changed. (this has happened before by the way same exact procedure in fact, and must be part of the training).
I’m trying to hold my volume down and not get too upset. Its not the techs fault and probably does not know I have gone through this procedure before. I want to try to explain this but he is busy trying to work his magic. I remain calm, but I even made the statement that I would probably be calling him back in 15-minutes. I try to end the conversation and phone call as politely as I can. Its not his fault, his just trying to do a job.
Anthony
Case Number: 053300005
Well not even five minutes later you will never guess what………… Pings start dropping and the internet is cutting out on me.
The Problem-
The problem has been defined as a Line Issue, and an On and Off interrupt of service. At this point even the TV is being affected. From the first time I called (like over a year ago) the issue is defined to me as an On OFF issue.
The Problem trying to get this fix-
You apparently have no Line Techs.
The Pole near my house is apparently a Forbidden Area that no one must go near. LOL
You cannot get these people to go near it apparently. They only classify the problem and go away never to be seen nor heard from again.
Now honestly I can understand with employee issues seeing this happening from time to time, but not for over a year and with service calls up in the tens and twenties…..
Worst of All-
I think the worst part of all of this is I have become so used to the poor and substandard quality of service. So used to it that I only call or complain when its totally out or is visually not working correctly and can be tested. I don’t call and complain because its not working as Advertised, because in fact it really never did or does.
I also, don’t call a lot of the times because of dealing with the service department. If its working at that moment they cannot define the problems. Not really anyone’s fault as it looks like its working even if the pings are in the 200 range or currently no time outs are accruing. I mean at least its working, and they say Speed is not Guaranteed anyway.
The Forgotten and Unanswered Questions-
I don’t know about the rest of you but sometimes while talking to people I forget to ask questions or the question does not come to mind until the conversation is over with. In any case, the Phone Service Tech said that what he did should have been done along time ago.
However, if my cable was somehow magically fixed by what he did I still have these questions;
1.What happened to my Service Call and why did no one call my by 6:00PM today?
-I waited around for the call actually, and I really would like to get this issue resolved.
2. Why is my TV picture still bad?
3. Although my internet seemed to be working today and only cut out once for a brief period of time why did the supposed fix of the Phone Tech double and even triple my pings, and still occasionally cuts out?
This is usually when I can tell its going to start acting up as the interrupts become more frequent and growing in intensity and length. I always have them anyway I am used to it.
However, on the other hand, I am already seeing time outs and interrupts and should I be paying full price for a lower quality of service compared just to my next door neighbor ?
This is a very hard question for me to ask myself. I like using Cable rather than a Dialup Service, but there is also the whole principle to the matter as well.
*Should I pay full price for a service that is substandard to everyone else’s?
*Should I pay full price for the same connecting I used to get a discount for, because of the poor quality?
*Should I call and complain everyday and turn this into a daily ritual? I cant keep taking time off from work to wait for someone who does nothing except stand around and futz with the computer for 20mintes and recognize the issue.
*Should I have to complain so much and go through the process which is like pulling teeth to get you guys to do something about it?
Maybe this is all my fault, and I am doing something wrong. What do I have to do to get this fixed? I don’t want to have to get DSL, so someone please help me. What am I doing wrong. I cannot keep taking time off from work to have someone come out only to recognize I have an issue and never fix it.
To Whomever at Comcast:
Is it so wrong of me to want, after a year of having repeated service calls with no resolution to the issue to ask, and request, that the cable service provided to me is the same as everyone else’s?
If you handed noticed-
Well if you haven’t noticed by now I am really tying to get this situation fixed and resolved. Mostly because, it is to the point where I am going to have to stop using Comcast and get DSL, or AOL or something because its more reliable. Which I really don’t want to do in the first place cable is supposed to be reliable and always on and faster.
A little over a year not and I am running out of options though.
Seriously Cant anyone help?
Message was edited by: Anon1245678

Part/3-
Swami
Wed/Jan/18
An eventful day-
Just a few minutes ago, got a phone call from the Comcast Cable GUY (2:20pm). He then Says he’s been working on trying to find the problem from 1 O’clock. Apparently, and maybe the case, (it was a brief conversation and he will get back to me later) but maybe some part has gone bad somewhere and he said he was waiting on a phone call from someone else.
In any case, he said that they are trying to clear up the problem and that its been running better sense the Jan/14.….? Not here it hasn’t. LOL We also had a brief discussion about how due to my repeated use of the internet that maybe I notices this more than other people do. My next door neighbor does not seem to have any issues last time I talk to them. But the guy said someone who lives on Broadway (few streets over) has been having issues too so maybe its this part.
I said; So I should see some improvement today… silence…and a brief pause….. After I find out what the problem is Ill come over and discuss it with you so you know exactly what is going on.
I do have a feeling I am going to be told this is going to take weeks to fix or at least awhile. Apparently a Part is needed maybe. Ill have to wait until the guy shows and gives me a full explanation though.
I called my wife and told her of the event and she is pretty emphatic about returning the TV cable box as the TV picture is better without it and she only really looks at the local or 3-like 70 anyway. She was like “Bad Part?” well its been bad for over a year then! We should get a refund for the whole year then… Sorry Comcast she is on a Refund Kick… I just want it to work.
Part/4-
The Tech Supervisor Mark, showed up at my door and tried to explain the issues. I felt kind of bad cause I probably know he got Chewed on along with some other people probably. At least they sent someone older and who looked like he had more experience and knew what he was talking about and could actually find the issue.
I tried to be as apologetic as I could, and tried to explain that its just because this has been such a persistent issue over the past year and a half, and I have had way too many service calls for this not to be fix by now. I even went so far as to explain; it’s a new year and we are trying to get this problem finally fixed. I was also quick to mention how nice it was outside and that at least it was a good day to run around outside. I would have felt really bad if it was raining or snowing out, but it was a nice day probably upper 60s and sunny.
We briefly discussed the issues and he said he and some others (I guess) had been working t the Head End fixing some issues… Which actually might have fixed my TV picture, seems better right now currently though. Currently NO digital Blocking on any channels currently, but as I said, it’s a sporadic issue popping up one day and going away the next or the problem lasting weeks and months then nothing for a few days and weeks.
Mark, tried to explain that maybe the problem that I might been having (apparently along with a few others) was that a Temporary Line was connected on the MAIN. Basically 1” Main Line Cable run it to cable like that’s in your house (cant remember but off hand I think its 5, 10 or 15 gauge cable) and back to 1” Main Line Cable. It was all a little technical, I just nodded and said yes, and at least you might have found the issue right?
He didn’t know how long that had been like that, and I said; probably for over three years as the previous owner had issues too, or at least sense I had bought this house about a year and a half.
I went so far as to showed him some print screens of some of the issues I have been having, and I know he noticed all the yellow recites in my computer room. : P Unfortunately, I deleted all my old Print Screen saves when the guy last Monday (ninth) showed up and said he would fix the line, or at least track it down. I only had one from the previous night to show him or something.
In any case, while discussing this Mark, said the guy that came out the other Monday never filled out a work order or something like that. I basically tried to explain that is the kind of thing I have been dealing with for little over a year. Tech after Tech after Tech; as I looked at all the yellow recites on top of my computer desk.
Mark also, basically said, I should have pretty fast cable considering I only have two nodes and then basically it runs back to Comcast, or something like that. However, that Temporary Line is probably causing the issues. No definite date on a fix, but maybe 24-hours or a few days, but the matter had been expedited or something like that. *Cross fingers*
That’s the real issue with this cable, its sporadic, and comes and goes. I’m pretty sure they are going to try to replace that line, but you know what….. I have heard that before actually. I have actually heard that for over a year now. Even the expedited part. : P
Mark tried to thank me for pointing out this issue, and made some comment about how its actually helping them….but………. I can kind of tell he had been getting yelled at or something by someone. It was not obvious, but I could tell.
I felt kind of bad about that, but… That happens when you work for someone, and the people who work for you (below you) don’t do what they are supposed too.
I kind of tried to briefly explain to Mark about the issue again and that usually by the time a Supervisor gets out the issue has cleared up for a time….. Odd how that works by the way. But basically I got the old…well it looks like its working ok now and you should have seen some improvements over the last few days… thingy..
We started talking about that Temporary Line being connected again and I walked Mark to the door and we said our goodbyes and I apologized again for being such a pain in the about this whole matter.
Part/5-
I called the wife and told here about everything. The first thing she asked is; is it fixed? She is still not happy especially when I tired to explain what the issue was and probably was and that at least maybe they found it.
I have no idea of what kind of onward action maybe on my part in the end if things don’t get better. Its like trying to argue with the old Bell Telephone Company when that was the only phone company in the US and no other phone companies existed.
I hope to one day, be a satisfied Comcast Customer, but to date I have yet to feel that way, at least with the Internet in any case and that’s only because I really don’t watch TV.
I am also, hoping when, and if, some LINE is replaced somewhere that I see some drastic improvement along with apparently a lot of other people in my community and a lot less issues also. I still don’t believe that I should be just setting for; Ok well at least its ON now, or the light has finally stopped flashing.
All a SNAFU?
That’s highly questionable at this point, and I have to be honest with you. This is going on a year and a half of dealing with this. This SNAFU, could be the case, but it seems more like policy, or a standing Comcast Company Directive actually if you want my honest opinion. I don’t know what the Maintenance Budget is for my area, but you might want to consider doubling it, or tripling it.
I really don’t care actually when this is fixed, as long as the issue is fixed. I cannot make a final judgment until it is finally fixed and go on and try to take further action onward from that point.
Thus far I have only been given an explanation. I don’t know if anyone at Comcast realize exactly how many times I have had an explanation given too me though (either on the phone with a service tech or from an actual person “tech” at my house). The list is extensive of the actual explanations I have had over the past year and a half, but my favorite one is; squirrels.
Part/6-
We are still waiting on phone calls from people who said they would call us back today and check what’s going on. Both of us, (me and the wife) are slowly losing momentum again as this whole issue gets dragged out for weeks and weeks at a time.
She is tired and I’m tired too, and Comcast is warring us down again it looks like. My wife was like; “do I have to call them, I really didn’t have a good day anyway and I’m tired. They were supposed to call us anyway, lets wait.”
I tried to make a phone call (half heartedly, I myself as I’m tired too) as Carla (at my local Comcast office) wanted to know how the service call went, but after repeated attempts and being shuffled off to Billing, and then being put on hold : P ……and its actually getting close to dinner time. Maybe after dinner if I don’t just fall asleep first.
So, in the end its still hang on for a few more days, and or, wait to have the problem fixed. Your guess is as good as mine, people. More Smoke and Mirrors or an actual Fix. Your guess is as good as mine.
As for me, I’m going to bed, I’m worn out. Maybe a new line to replace that temporary one, maybe just saying I might get a new line to replace that temporary one.
The Saga continues. Maybe it will end someday.

HELP! How can i restore/recover files from Bootcamp with Boot Failure - Missing operating system error?

Hi,
I am having a few problems with bootcamp on my imac. When i tried to move the bootcamp partition on windows 7 into free space, it crashed and turned off. Ever since i have had the error 'Missing operating system' and it fails to boot. I have some very important files on the bootcamp partition. Is it possible to recover these files or even to restore the bootcamp partition to it's original state? I do not have a backup of my bootcamp partition. Another problem i have is that ever since i tried to expand my macintosh HD partition into free space, when i hold alt while booting up (to choose which partition to boot like i normally do), the bootcamp partition has stopped appearing. This means that i cannot even boot the windows 7 bootcamp partition anymore!
So basically here are my 2 questions:
How can i restore/recover files from Bootcamp with Boot Failure - Missing operating system error?
How can i make the Bootcamp partition appear in Startup Disk and when i hold the option key while starting up my computer to allow me to boot windows 7?
Any solutions are very much apreciated!
Thanks!
I know that bootcamp (disk0s4) hasn't been fully deleted since it appears in disk utility (i cant do anything to it though)
And here is the error i see when i try to launch bootcamp (back when i was actually able to boot up bootcamp to the error screen)

WinClone 3 is OS X and saves Windows image it makes for restore - that should work but you will have to try and you would need to make a new image unless it also works with a native Windows system restore image. It is now supported and has come a long way.
http://www.twocanoes.com/
Paragon Clone OS works and does disk-to-disk clone just like CCC you end up with two bootable drives. But does not work with your setup. It would let you clone and move your Windows install to an SSD or another disk drive though and be bootable.
During its clone process it checks for errors which is very helpful and lets you know - something CCC and others should adopt more of.
http://www.paragon-software.com/downloads/demo.html
I wish for our/my sake you had re-read and rewritten the long 'story' and broken it into a brief list of facts we needed.
OS X
Windows
Backup (though external is much safer) and you want bootable OS X clones as well as TimeMachine
https://support.apple.com/kb/HT1427
https://support.apple.com/kb/HT1553
There are a number of things to do like chkdsk and others as well as Windows DVD to do automatic system repairs and find out why.
AppleHFS - the abilty to mount and read HFS volumes can be notorious.
I would rearrange and redo your storage setup and how you use the 4-5 internal hard drive bays.

Boot failure following Windows 8.1 update. shows reason: irql_not_less_or_equal

Hi,
I have the dreaded BSOD with irql_not_less_or_equal boot failure.
The PC was running Vista when bought, which was subsequently upgraded to Windows 8. This was done via an online purchase & download of the Windows 8 Upgrade, so I do not have any installation media. I have also updated (again online, so no physical media)
to Windows 8.1
I have recently had to shut the PC down (it usually stays on all the time), but now it refuses to boot, going straight to the new style BSOD, showing 'irql_not_less_or_equal', which then restarts in to the system restore menu.
I have tried to remove some peripherals - removing the video card (now using the display adapter on the MoBo), a USB 3 card & a USB head-set dongle - which has improved the situation a little - it now boots to the log-in page (sometimes), but will
BSOD after about 10 seconds, regardless of whether I am fast enough to log-in, or not.
I have tried (from the System Restore menu) to do a restore to a previous state, but it doesn't seem to be able to find the restore points.
Note, the BSOD occurs if I boot into 'Safe' Mode, or do a normal boot.
The bottom line is:...
I can't boot to Safe Mode, get to any system maintenance tools, so I can't disable/uninstall any drivers.
Windows 8 & the 8.1 update were purchased online & downloaded, so no boot disk(s).
The recovery points I have made do not seem to be accessible.
Any advise on how to proceed?
cheers
Paul

now boots to the log-in page (sometimes), but will BSOD after about 10 seconds, regardless of whether I am fast enough to log-in, or not.
That should be enough time to get to the Shift-Restart option. <eg>
Since you can see what you're doing you don't even have to do the backwards method that I was long proposing so that users who were trying to do this in the dark would be able to bypass their password field. But maybe using a set of Backtab (Shift-Tab)
Shift-Space would be more efficient anyway?
Here is an example of an explanation of the technique:
http://social.technet.microsoft.com/Forums/en-US/37eff8a6-74a3-4775-90d7-e0aa86c68424/windows-8-black-screen-at-boot?forum=w8itprogeneral#0dc40edd-4e3b-466b-b4af-37c532eb844a
<quote>
In order to try to avoid hitting the Password field in this uncertain state I suggested using Backtab (e.g. Shift-Tab) to do the navigation. Fortunately, the pressing of Shift- would solve the problem of whether you were on the Lock screen or already on
the Login screen. So the iteration would be Shift-Tab, Shift-Space (Fortunately, the Restart item is at the bottom of the Shutdown menu.)
</quote>
HTH
Robert Aldwinckle

Boot Failure iMac G3 400MHz, goes on firmware mode :S

Hello everyone,
I recently bought a second hand iMac G3, 400MHz processor and 128mb ram, 10gb harddrive. I've always wanted a Mac just for the fun of it, and i finally got it. I dont think this imac is dead, but i'm having trouble on boot. It is not booting the traditional way, it is going down to firmware boot.
It gives this info:
MacOS: Boot Failure! (0xF3C481F6)
Mac OS: parcel initialization failure - bad checksum
Then i have 2 choices from the firmware for booting or shutting down 1. mac-boot command and 2. shut-down command.
So, i give it the mac-boot command; in starts showing the mac face for a few seconds, then it displays this message below of it:
/pci@f2000000/mac-io@17/ata-4@1f000/disk@0:5,\\:tbxi
after maybe a minute it finally displays the face and ? symbol; typical of not finding the system. Problem is that, even starting the imac with the system disc on it and pressing "c" at bootime, it still goes to the firmware thing...
Is there a way to tell the imac "hey dont boot at firmware, boot at cd!!" ??
Oh, by the way...during the "/pci@f2000000/mac-io@17/ata-4@1f000/disk@0:5,\\:tbxi" message I can still press the "alt" key and it shows me the retry arrow, the system harddrive labeled "Lorelai's comp", the system CD and the straight right arrow.... i try clicking on the harddrive and also on the CD icons to try to boot, but it only refreshes the screen changing from the traditional blue/purple background to a red-ish background and arrow/drive's buttons get funny colors...
i dont know what is going on....i dont think the imac is dead....i guess it has to do with that firmware booting default thing...
please help....
thanks in advance.

Hi again Kenichi,
Question: I've done that procedure yesterday, but i pressed the button for only 1 second 1 TIME ....can i make the procedure again despite if i did it 1 time before? or doing it again will crash the iMac forever?
About the black screen i told you before, here's the thing...if i place a battery on it and reset the nvram via keyboard commands or firmware commands, at the restart then is when the imac goes on black....BUT if i remove the battery, leave it there for a minute or 2, and then power it on, it goes to the firmware state again, ofcourse with good video on it....i dont think it has a video problem...but i dont understand why when making the reset procedures with a battery on the iMac this black-non starting screen keeps going...
Thanks in advance.

Disk Boot Failure, Insert System Disk and Press Enter

I have been experiencing an intermittent disk boot failure for the last few months on my HP Pavilion Slimline PC. At first, it would occur once every week or two, typically when the computer would boot up after being in hibernation. After turning off the computer and turning it back on, everything worked normally. Within the last month, the failure began occurring with more regularity.
This week, I started receiving the error every time the computer would boot from hibernation. I went into the BIOS and saw that the system was not recognizing the hard drive. I tried changing the boot priority to boot from the HDD first, but to no avail. Today, the system worked as usual until I performed a restart, and it has yet to work again. Additionally, the performance has taken a nose dive over the last week (slow processing, programs not responding, etc.).
System Specs:
HP Pavilion Slimline s3710t PC
250 GB SATA Western Digital HDD (Caviar Blue)
Intel Pentium Dual-Core Processor
Windows Vista Home Premium (32-bit)
3GB DR2-800 MHz SDRAM
I have read through many technical forums, including HP’s, and followed all of the advice. I have again changed the boot priority to HDD first, restored the default settings, etc. The only drive I can find listed is the DVD drive on the unit, which is listed as the second drive. There is no first drive listed in the main tab of the BIOS CMOS Setup Utility.
I attempted to run a system recovery, but it is not even possible. Upon running the diagnostics, it of course mentions that there is no hard drive connected. Upon entering the boot menu, it also only lists the DVD drive.
My next course of action was to remove the side panel and reseat the connections on the hard drive, as well as the connection to the motherboard. This was also unsuccessful, and I have not been able to boot up the computer again today.
The computer itself is 1.5 years old and this is the original hard drive that shipped with it. I have never opened the computer, prior to today. The symptoms started a few months ago, just outside of the warranty period.
Based on the forums I have read, it all signs are pointing to a bad hard drive. This is hard for me to believe, as the computer is relatively new and does not get much use. The use it does get revolves around email and Internet access, as well as use of Microsoft Office.
As you can imagine, I am not happy about the prospect of having to buy a new hard drive, as well as pay for the data recovery on the original drive. I hope that someone at HP can come up with a better solution, as a 1-year life on a hard drive is pretty pathetic.
Thanks,
JR

HI JR,
You situation does not sound good if the PC doesn't recognize your hard drive.
Boot into the bios and run some bios hardware diagnostics.
Try clearing the CMOS.
Try this procedure:
Unplug the PC and open it up. Clean out all the dust. Carefully remove and replace all the cables going to the motherboard one at a time. Do the same for the memory dimms and the video and sound cards if you have any. You might want to buy a can of compressed air to blow the dust out of the CPU heat sink. Plug your PC back in and give it a go.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

[svn:osmf:] 17499: Partial fix for FM-990: prevent RTE when attempting smoothing for an image where a policy file was not available

Revision: 17499
Revision: 17499
Author:   [email protected]
Date:     2010-08-27 11:05:22 -0700 (Fri, 27 Aug 2010)
Log Message:
Partial fix for FM-990: prevent RTE when attempting smoothing for an image where a policy file was not available
Ticket Links:
    http://bugs.adobe.com/jira/browse/FM-990
Modified Paths:
    osmf/trunk/framework/OSMF/org/osmf/elements/ImageElement.as

Revision: 17499
Revision: 17499
Author:   [email protected]
Date:     2010-08-27 11:05:22 -0700 (Fri, 27 Aug 2010)
Log Message:
Partial fix for FM-990: prevent RTE when attempting smoothing for an image where a policy file was not available
Ticket Links:
    http://bugs.adobe.com/jira/browse/FM-990
Modified Paths:
    osmf/trunk/framework/OSMF/org/osmf/elements/ImageElement.as

Boot Failure - Partially Fixed

Similar Messages

Maybe you are looking for