Bootable CD...Please Help...nOOb
I downloaded the entire set of binaries from SUN for Solaris 8.
Readme.txt
installation cd:
sol-8-u7-install-sparc-a.zip
sol-8-u7-install-sparc-b.zip
sol-8-u7-install-sparc-c.zip
software cd 1/2:
sol-8-u7-sparc-v1-a.zip
sol-8-u7-sparc-v1-b.zip
sol-8-u7-sparc-v1-c.zip
software cd 2/2:
sol-8-u7-sparc-v2.zip
Then I compiled the segments to a single .iso file as instructed (sol-8-u7-install-sparc.iso). Then I tried to make the installation .iso file a bootable cd. I tried both with CD Creator & NERO, but to no avail.
The CD's are not even seen while booting the computer. When I used NERO it only copied the .iso file as-is and didn't even make the CD in anyway bootable. CD Creator on the other hand made the following files:
.VOLUME
ADD_INSTALL_CLIENT
BOOT
COPYRIGHT
MODIFY_INSTALL_SERVER
RM_INSTALL_CLIENT
To me I would think that this would work just fine. As the system(s) boot-up they just pass right by where the CD should kick-in. And I have tried on three different computers too. Two clones and a HP Kayak XU.
I have the setting in my BIOS to Boot from CD first as well.
Also do I need to make the software CD's bootable, or can I just burn the iso file straight to CD?
F.Y.I ... I had downloaded RedHat and just burned the iso files to disk and worked. Do they install in a similar way?
Thanks much you guru you in advance. :D
hummmmmmmmmm......
I think I have found an answer to my own question.
Is the version I downloaded only for SUN hardware(SPARC)?
Do I need a different version for i386?
Similar Messages
-
I have an intel based mac with 10.6.8 mac os x. How to install windows 7 using usb as the bootcamp doesnot have the option of creating a bootable usb. please help
Welcome to Apple Support Communities
You can install Windows from a USB drive in one of these computers:
- MacBook Pro with Retina display.
- Mac mini (Mid 2010 and newer).
- MacBook Air.
- iMac (Late 2012).
If you don't have any of these Macs, you can't install Windows through a USB drive. Instead, buy Windows on a DVD. Follow Apple's steps > http://support.apple.com/MANUALS/1000/MA1519/en_US/Boot_Camp_Install-Setup_10.6. pdf -
Please help noob debug why updating template duplicates content
Please go to
http://www.mmssupplier.com/
to read the code and help me figure out how to stop my pages from
duplicating content or a partial table whenever I update my
template. It only does this to some of the pages that I built from
the template. I'm not a code expert and cannot figure out why it is
doing this. On that link the header and content on the bottom is
the one I want, not all that top duplication, thanks, I really need
help.Hmm - then it's hard to imagine what you might be doing to
cause this
anomaly.
The good news is that your template is pretty OK. The
validator only finds
5 errors there -
1. Error Line 69, Column 41: there is no attribute "height".
<td><table width="100%" height="110"
border="0" cellpadding="0"
cellspa
There is NO 'height' attribute in any HTML specification for
the table
tag. Since you cannot reliably use this attribute, you should
just remove
it from your code.
2. Error Line 88, Column 320: value of attribute "align"
cannot be
"absmiddle"; must be one of "top", "middle", "bottom",
"left", "right".
ight="37" border="0" align="absmiddle" id="home2"
/></a><br />
The absmiddle attribute is similar to the table height
attribute - supported
by some browsers, but not valid HTML. Just remove it.
3. Error Line 92, Column 260: value of attribute "name" must
be a single
token.
jpg" alt="health_issues" name="health issues"
width="130" height="37"
border=
You cannot assign a name value that contains spaces.
4. Error Line 92, Column 314: value of attribute "id" must
be a single
token.
30" height="37" border="0" id="health issues"
/></a><br />
You cannot assign an ID value that contains spaces.
5. Error Line 127, Column 61: required attribute "alt" not
specified.
ea shape="rect" coords="2,2,125,31" href="/index.html"
/>
All images on the page should have either a descriptive alt
attribute value,
or an empty one, e.g., <img alt=""....
Fix those errors, please. Then we can re-examine how you
might be stumbling
onto this duplication in your pages.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"stephanierolfe" <[email protected]> wrote
in message
news:[email protected]...
> no, I don't apply to existing child page. I create new
page each time,
> based on
> that template.
> And yes, I'm starting to get that. I thought I knew
enough HTML to pull it
> off
> and created one large site already,
http://www.nutritionarticlesonline.com
> and
> it works great, no problems with corrupted templates.
I'd like to persist
> with
> DW since I've invested over 6 months already using it.
Despite the 91
> errors,
> it works fine except this updating template problem.
> -
How do you take the back off to insert a new sim? please help
Look in the docs: You stick the end of a paperclip in, and the SIM tray pops out the top. No taking the back off.
-
Re: Z97 gaming 5 uefi windows 8.1 instal now i cant use the bios please help noob
Quote from: Svet on Today at 11:14:35then probably you will unable to figure what's the reason for this
you can contact Zotac support to ask for vbios update for your card which maybe can helps with thisQuote from: Svet on Today at 11:11:48told you, answer with "Y" to any ID errors and to all other flash questions
just flash what you need to flash with regardless what warning you will receive, ignore all of them -
Please Help i am a noobie ! Adobe Flash Builder premium
Heelo Everyone , recently , I downloaded the latest version of Flash builder . i want to know how i can enter the codes which would be executed when i click the button i have created . For example can someone tell me the code to display a label , a button or how to change the state or view when that button is clicked . I am developing a desktop application . Can someone please help me to change the default background color or even insert my own background image. I have reache it till here. please Help me to develop the reqquired application . I know that these are the very basics so i cant develop further without it. I have currently reached till here and have completely understood the matter till here . please dont be evil and copy the code for your own project.
My current progress:-
<?xml version="1.0" encoding="utf-8"?>
<s:WindowedApplication xmlns:fx="http://ns.adobe.com/mxml/2009"
xmlns:s="library://ns.adobe.com/flex/spark"
xmlns:mx="library://ns.adobe.com/flex/mx"
width="800" height="600"
minWidth="800" minHeight="600"
maxWidth="800" maxHeight="600"
title="XYZ">
<fx:Style source="XYZ.css"/>
<fx:Declarations>
<!-- Place non-visual elements (e.g., services, value objects) here -->
</fx:Declarations>
<s:states>
<s:State name="splash"/>
<s:State name="mainmenu"/>
<s:State name="options"/>
<s:State name="XYZ"/>
</s:states>
<fx:Script>
<![CDATA[
protected function continueBtn_clickHandler(event:MouseEvent):void
// TODO Auto-generated method stub
]]>
</fx:Script>
<s:Label left="274" right="269" top="83" bottom="274" fontSize="36" horizontalCenter="2"
text="XYZ

XYZ:-" verticalCenter="-96" includeIn="splash"/>
<s:Button id="continueBtn" x="305" y="431" label="Click to Continue and Play the game " includeIn="splash" click="continueBtn_clickHandler(event)/>
<s:Label x="274" y="322" color="#00FF48" fontSize="36" text="Traffic" includeIn="splash"/>
<s:Label x="416" y="322" color="#FF0030" fontSize="36" text="Manager" includeIn="splash"/>
</s:WindowedApplication>So you're completely new but you're worried someone
will use your code??
I'll try to answer the immediate questions but you really should sit through some tutorials as suggested.
Displaying a label: you can just add this in MXML and set the visibility=false, and on need address the id of the label to set the visibility to true.
(eg) <mx:Label id="lbl1" x="179" y="113" text="Label" visible="false"/> then when you need to show it in AS you can use: lbl1.visible=true; and it will display where you have it. You can also create the label on the fly in AS and position it.
"Can someone please help me to change the default background color or even insert my own background image."
Not sure where you are trying to set this but the easiest way is to use the Design View tab, select the component and then go down the list on Flex properties on the right in Flec Development Perspective.
or you can manually find your component and add backgroundColor="theColorYouWant
" in the list of attributes
background image:
Just put this under the <mx:Application > tag
<mx:backgroundImage>@Embed(source='//relative path to image in your project')</mx:backgroundImage>
"a button or how to change the state or view when that button is clicked"
click="{currentState='options'} add something this to the attributes of the MXML button component. 'options' being the name of the state you want to switch to. If your base state is not named use currentState=' ' to switch to it.
Once you've sat through the tutorials.
Do a google search for flexblogs and there are some good ones that show examples on how to do some basic to advanced things, it is very useful for the resourceful newcomer to flex.
Good luck with your project. -
Runtime Exception.... NOOB JAVA PROGRAMMMER HERE. PLEASE HELP!
Hey Oracle ppl,
I'm a real n00b Java programmer, just learning Java through SL-275-SE6. So, here's a small program that I created, but I get this runtime exception while running it in NetBeans v7.1:
java.sql.SQLException: [Microsoft][ODBC Microsoft Access Driver] Too few parameters. Expected 1.
Here's the source code:
import java.io.*;
import java.sql.*;
public class Expenses {
void DataBaseInteract() {
try {
Connection con;
Statement st;
Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
con = DriverManager.getConnection("jdbc:odbc:Expenses");
st = con.createStatement();
st.execute("create table Expenses(DateofTransaction String, Amount float, Remarks String)");
DataInputStream in1 = new DataInputStream(System.in);
System.out.println("Enter today's date, in the format DD/MM/YYYY.");
String DateofTransaction = (in1.readLine());
System.out.println("Enter today's transaction amount, ");
float Amount = Float.parseFloat(in1.readLine());
System.out.println("Enter remarks, if any:");
String Remarks = (in1.readLine());
st.executeUpdate("insert into Expenses values("+DateofTransaction+", "+Amount+", "+Remarks+")");
con.close();
catch(Exception e) {
System.out.println(e);
public static void main(String[] args) throws Exception {
Expenses obj = new Expenses();
obj.DataBaseInteract();
Please help! I really want this program up and running!!!better you can get help from http://forums.netbeans.org/
eventhough.
here some inputs,
http://www.justskins.com/forums/too-few-parameters-expected-80937.html -
Hey. I have never used automater and don't know how to use it but I was wondering the extent of it capabilities. What I really want it to do is log me onto facebook and send something every hour. Is that possible. With those familiar with facebook, I'm trying to send schrute bucks to a friend. We're in a contest among friends.
The same thing happens to me when I am using Microsoft Internet Explorer 7 on my Gateway (Windows XP Home, SP2, 512 RAM). However, once I get the error message, and open another QuickTime file, the browser displays a "IE has encountered a problem and needs to close," and shuts down MSIE. Please help!
Macbook 1.83 GHz Mac OS X (10.4.7) -
System config problems please help!!!!
I bought a windowns recovery disk for my toshiba satellite L450D and everything was okay until I reached theconfiguring system partI left it go for about 2 hours but nothing happened so I restarted and I still have the same problem can someone please help me with this because I don't wanna buy a new computer
If the recovery disks are not working then it is either an issue with the disks or a hardware issue with the computer. I would start with the disks. Contact Toshiba (where you bought the disks) and tell them the disks are not working. If possible, try and see if they will issue you the recovery media on flash drive as that seems to work better than the cds. Another thing you can try is (if possible) swapping parts of your computer into a know working computer to ensure they are all in working order (hdd, ram). It is also not a bad idea to wipe a hdd before attempting to do an install. this can be accomplished using third party software which can usually be accessed via bootable cd.
L305-S5955, T9300 Intel Core 2 Duo, 4GB RAM, 60GB SSD, Win 7 Ultimate 64-bit -
I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)
The question mark means the computer cannot find a bootable volumes so can;t do anything, That, combined with annoying sounds, strongly suggests a failed hard drive.
You can ask a "genius" at an Apple Rtail Store to test it but I'm pretty sure the drive is kaput. I'm hoping you had your data backed up. -
I tried googling several solutions, but so far nothing seems to work. Everytime i start up my laptop i press CMND+R to make it go to the repair disk utility but instead it takes me as if i have to install lion when i had Snow Leopard 10.6.8. When i do go to the repair disk utility, on the eft hand side shows two hardrives one is Untitled and another is Hitachi, i tried downloading snow leopard 10.6.8 onto a Re-writable disc using my windows computer. When i insterted it onto the disc drive it came out under SUPER DRIVE and everytime i double click on the CD it says something about attaching images/ I also forgot to mention that the MAC OSX 10.6.8 Update shows on the left hand side on the bottom in DMG format. I dont know what else to do, please help?
DestroyGalaxies wrote:
a flashing folder came on with a question mark in the middle of it
This is the firmware telling you it can't find a bootable OS X volume.
Usually to solve this all you do is hold the option key down on the built in keyboard while booting the computer, this enters Startup Manager and then you choose OS X to boot, then in System Preferences > Startup Disk you change it to the boot volume and it tells the firmware.
Everytime i start up my laptop i press CMND+R to make it go to the repair disk utility but instead it takes me as if i have to install lion when i had Snow Leopard 10.6.8.
What you have is a 10.7 or 10.8 Recovery HD from when 10.7 or 10. was on the machine previously.
The Macintosh HD partition only was erased and 10.6 installed on it, without erasing the entire drive like what should have occured to remove the Recovery HD partition.
So you have a mucked up machine.
i tried downloading snow leopard 10.6.8 onto a Re-writable disc using my windows computer.
Well there goes your problem there, your downloading illegal copies of Snow Leopard from a untrusted location.
10.6 is not available for download, except from pirate sites. You likely have malware or a compromised system.
I dont know what else to do, please help?
What you need to do is call Apple via phone, tell them the make of your machine and order the appropriate 10.6 disks, they are inexpensive now. Some machines that came with 10.6.3+ origianlly need machine specific disks, other wise pre-10.6.3 Intel Macs can use the 10.6.3 white retail disks.
Once you have the disks, you need to backup your personal information off the computer to a external storage drive using the emergency quick copy method, then disconnect it to prevent mistakes.
Most commonly used backup methods
Next follow this proceedure and make sure to select the ENTIRE drive on the far left with the drive makers name and size, this will erase the entire drive, then install 10.6 from the disk
How to erase and install Snow Leopard 10.6
When finished setup the machine and log onto the Internet and use Software Update to get current on 10.6.8
Don't use pirated software, it's likely been compromised in some fashion. -
Please help!!!!!!!! I am having a big problem with my mac
This is the whole story that has been going on. I posted yesterday and Ray told me to repost and see if someone else can help. Please dont know what to try next.
Problem with my Imac
Posted: Dec 27, 2007 7:01 AM
Click to reply to this topic Reply email Email
Ive been having a problem with my Imac 10.4. I believe that when my computer was doing the last update someone manually shut it down since then i havent been able to get into my hardrive to start up my computer. I brought it into the apple store the guy at the genius bar told me that he couldnt locate my hard drive and i would have to get a new one. I didnt purchase the new one I went home to see if i can resolve it on my own. I went out and bought a external hard drive and bought a program to fix the hard drive. So now the hard drive pops up on my computer and im able to get into it and i backed up most of my information on to the new hard drive. If now that i can see the hard drive is there any way to repair it so i can start using my computer normally again? Please help
Re: Problem with my Imac
Posted: Dec 27, 2007 7:06 AM in response to: Shelomo
Click to reply to this topic Reply email Email
In utilities there's disk utility, find your HD, the one you want repaired and run the repair permissions program.
Ray
Posts: 12
From: New Jersey
Registered: Dec 27, 2007
Re: Problem with my Imac
Posted: Dec 27, 2007 7:11 AM in response to: smithrj
Click to reply to this topic Reply email Email
I already tried that but I read somewhere else to try that a couple of times. Can you tell me what i should try after that?
Shelomo
Posts: 317
From: Syracuse, New York
Registered: Jul 13, 2007
Re: Problem with my Imac
Posted: Dec 27, 2007 7:18 AM in response to: Shelomo
Click to reply to this topic Reply email Email
What's left to do? Does the permissions tell you your HD is OK? Be more specific in what you want to do, I don't understand Shelomo. Post what it is you want done. Because there are many 3rd part applications that may solve your problem.
Cheers,
Ray
MacBook 2GB Intel Mac OS X (10.4.11) iMac 2Gb 2.8GHz 500 w/ 10.4.11 iPod shuffle 1 GB
Shelomo
Posts: 12
From: New Jersey
Registered: Dec 27, 2007
Re: Problem with my Imac
Posted: Dec 27, 2007 7:22 AM in response to: smithrj
Click to reply to this topic Reply email Email
I ran repair disk first and it said that there was an underlining error, and i did that before i ran permissions. Will it work after the permissions is finished running?
imac 20" Mac OS X (10.4)
smithrj
Posts: 317
From: Syracuse, New York
Registered: Jul 13, 2007
Re: Problem with my Imac
Posted: Dec 27, 2007 7:42 AM in response to: Shelomo
Click to reply to this topic Reply email Email
Repair permissions, if it tells you OK, your OK. No more to do.
Hope all goes well,
Ray
MacBook 2GB Intel Mac OS X (10.4.11) iMac 2Gb 2.8GHz 500 w/ 10.4.11 iPod shuffle 1 GB
Shelomo
Re: Problem with my Imac
Posted: Dec 27, 2007 8:18 AM in response to: smithrj
Click to reply to this topic Reply email Email
ok, when it finishes repairing can i send another message to you if this doesn't work maybe you might have another idea what to try? Thanx again
imac 20" Mac OS X (10.4)
smithrj
Shelomo
Posts: 12
From: New Jersey
Registered: Dec 27, 2007
Hi, ok so it finished running the reapir permissions and that came out ok, when I ran repair disk we got errors and the errors said ivalid record count, volume check failed, the underlying task reported failure on exit, 1 volume could not be repaired because of an error. Do you have any idea what I can try now. I really dont want to have to get a new hard drive put into my computer. Thank you
Shelomo
imac 20" Mac OS X (10.4)
smithrj
Posts: 317
From: Syracuse, New York
Registered: Jul 13, 2007
Re: Problem with my Imac
Posted: Dec 28, 2007 5:37 AM in response to: Shelomo
Click to reply to this topic Reply email Email
Shelomo, I don't know. Post the whole report using cut and paste and someone will jump in and help figure this out.
OK
Ray
SOMEONE PLEASE HELP ME!!!!!! Thank you very much
ShelomoWhat program did you use to fix the internal hard drive? What repairs did it report making? More crucially, if repairs were reported, did you re-run the utility until it reported no problems found? It's possible for one set of problems with a drive to mask others.
If you have about 5GB or so free space on the internal hard drive, you can use your OS X Install disc to perform an Archive and Install to recover from the failed Software Update. When the computer restarts, download and run the OS X Update Combo 10.4.11 (Universal). When the Mac restarts after that, run Software Update. During all this, make sure nothing interrupts or shuts down the Mac! Note that the first start after each of these updates will take significantly longer than subsequent starts, so be very patient.
How did you back up your internal drive to the external one? Did you just drag things over in the Finder, or did you use a utility such as SuperDuper! or CarbonCopyCloner? Does the external HD show up as a bootable volume in System Preferences > Startup Disk, or using Startup Manager? -
Quicktime and Itunes aren't opening up. Please help. Please.
Hello to all who have visited this post.
Basically i'm not very good with computers. So i apologise for the ''noob'' internet/computer knowledge.
I bought my Ipod a couple of months ago. Everything was fine. I could transfer songs from computer to Ipod without any problems.
But recently, when i try to open up Itunes, it dosen't open up. I try to repair/reinstall it but when i do that some message comes up ''fatal error occured'' so if anybody has some knowledge on how to fix this please help me.
I haven't installed any foreign applications as well. The latest ones i've installed into my computer are Codecs and this Nokia Pc Suite which helps me connect my phone to my computer Via USB. and other players such as ''Core Media Player, BS player, VLC player and FLV player.
Thank you for spending your time to read this.Have you tried conducting a search of Discussions with the subject "fatal error" or "fatal error occurred"? This will let you read the results of others experiences with similar or identical problems.
Also, Navigate on your computer to the following: Go to Start\Administrative tools\Event Viewer\System and left click the system heading. This will open the event viewer screen and show you information and error messages about your computer. Post the error number identified with the fatal system error you recieved, (look at the time stamps) and perhaps someone here will be able to diagnose your problem in more detail.
Dell Dimension 2300 Windows XP -
Please help! my iMac keeps freezing, mouse and keyboard do not work after
Early this morning I turned on my iMac and started downloading updates through software update as usual. I was browsing a website in Safari when all of a sudden the "zoom" feature activated itself and I could not turn it off. I restarted and the keyboard started typing different characters but not letters, so I took out my installation CD and it took me quite a while to reboot the computer using the CD as a startup. Since the keyboard had a different input, the C key was not running the CD. I tried loggin into the support page, but it downloaded the links into the desktop. I used system utilities to restart the computer from the CD, I verified the Disk Permissions, then Repaired the permisions, then the Verify Disk and then the Repair disk, in that order. I restarted the computer and everything seemed fine, but after a couple of minutes the mouse starts closing windows, downloading website links into the desktop and then the keyboard freezes and does not let me type! This has repeated over and over, and I don't know what to do!
Posting this message has been quite an achievement, because I have restarted the computer a lot of times in order to finish.
Someone please help! I don't know what else to do!!!
Thanks!Yes. And since you aren't backed up, you may have to use Prosoft Data Rescue to try to recovery any information that is critical. First though, do you have another Mac you can hook this one up to using Target Disk Mode?
If you do, that's another way to rescue information. Target Disk Mode is explained here:
http://docs.info.apple.com/article.html?artnum=58583
Similarly, if you have a bootable external hard drive, you can try to boot off that with the Startup manager:
http://docs.info.apple.com/article.html?artnum=106178
To rescue your information. This at least will allow you to do further analysis to see what data corruption might have happened. If the drive is invisible when booted off another, that may indicate a directory issue. But first let's see if we can attach or boot off another and see the internal drive of the machine. -
Hi guys
I tried the last two days everything from this forum. Run bootcamp, after restart (hold alt) go to the mac HD and delete or replace the bootcamp device (tried both options). had it almost done, at the end when it was installing/finnishing windows the error code "could not prepare the computer to boot into the next phase...... " and of course after that the "no bootable device insert boot disk and press any key boot camp".
Please help me to fix this thing!
Thanks a lot!
hopelessdumbPlease only use 1 thread https://discussions.apple.com/message/25160426#25160426
-
Please Help! Photo Import has Suddenly Slowed to a Crawl -- 19 hours
I have transferred 1,000s of RAW photo files to my HD and external HD with no problem, until a few days ago. Suddenly, what used to take about 3 hours now takes 19-24 hours. I can't figure it out.
I've changed card readers, I've tried different memory cards, I've even downloaded to external HDs and tried to upload directly to my HD. I've also hooked up my camera and tried to transfer the files via a USB cable (traditionally the slowest way). I've also tried to upload using different software programs: Lightroom, iPhoto and Bridge.
I've also ran the Disk Utility on my HD and there weren't any problems.
Nothing works.
Please help.If ran Disk Utility and only used +Repair Disk Permissions+, you may want to startup from another disk and run +Repair Disk+ (to look for and repair disk directory errors). If you don't have another bootable disk, you can startup from the Mac OS X (current version) installation disk. Insert disk and startup with the C key held down to start from the optical drive. When you get to the first Installer screen (after language selection), go up to the Utilities menu and select Disk Utility, then run +Repair Disk+ on your normal startup drive.
Also, do you have sufficient free space on your hard drive? While you were move those 1000s of photo file around, did your startup drive ever get to less than 10GB free?
Maybe you are looking for
-
Problen in assigning partner function at the time of creation of lead .
Hi ALL , I have requirement , where as soon as bp will be created a lead has to be generated mentioning the BP as sales prospect (partner function) . I have to assign employee reponsible partner function too in lead , at the same time . I
-
Upgrading APEX from 3.2 to 4.0 images and buttons not displaying correctly
Database 11.2.0.1 APEX: 3.2.1 Attemping to upgrade APEX from 3.2 to 4.0. The installation script runs fine and updates the database successfully. I run the .sql to import the images and it ran successfully however when I attempt to access the APEX ho
-
Thin driver 8.1.6 for JDK 1.2.x
What differences are there between the thin driver that can be downloaded from technet and the one that is shipped with Oracle8i2 EE (Win version)? The sizes and file dates are different between the two files and the classes12.zip that ships with the
-
Often slows down the browser also.
-
Picture in a Comment on the LabVIEW Idea Exchange
How do you post a picture in a Comment on the LabVIEW Idea Exchange? Richard Solved! Go to Solution.