Br350 - Diversity and drivers issue

Hi
I have a problem with the Aironet BR350, in the way it handles diversity. I run V12.05, and I use them as bridges with clients which means other bridges can route through.
I have Tx/Rx diversity enabled on both rightand left antennae, and I log the signal strength every second via SNMP. It is my perception that the radios will keep the connection down to 30-35% signal strength.
However, some times when the Rx signal strength on a non-root unit is averaging around 60-70, a singular drop to 35-40
(or even higher like 45)
would coincide with the root unit to restart the process to the non-root-bridge, which causes a dropout of about 30 seconds. Reason for the drop of signal strenght is believed to be a short temporary multipath fade much less than 1 second, and in some of these cases the signal quality also gets worse. But I only get one outlier hit in the log. It is too bad that this causes 30s outage.
At this time I know for sure that the other antenna has a reasonable signal.
Has anyone got any similar experience, and maybe a solution?

Hi
here is a transcript of debugging. Note that these are logged on the RootBridges network, and timestamp is when they arrive there after the link is restored.
Mar 16 06:20:36 [ip address omitted] NonRootWirelessBridge(Info): Associated to Parent
[Bridge_Root]00409656db77
Mar 16 06:20:40 [ip address omitted] NonRootWirelessBridge (Warning): Lost Authentication
with Parent
Mar 16 06:20:40 [ip address omitted] NonRootWirelessBridge (Info): Stopped driver for port
"br9"
Mar 16 06:20:41 [ip address omitted] NonRootWirelessBridge (Info): Started driver for port
"br9"
Mar 16 06:20:41 [ip address omitted] NonRootWirelessBridge (Info): Associated to Parent
[Bridge_Root]00409656db77
Mar 16 06:20:41 [ip address omitted] last message repeated 1 time
Mar 16 06:21:19 [ip address omitted] NonRootWirelessBridge (Warning): Lost Authentication
with Parent
Mar 16 06:21:19 [ip address omitted] NonRootWirelessBridge (Info): Stopped driver for port
"br9"
Mar 16 06:21:21 [ip address omitted] NonRootWirelessBridge (Warning): Failed to Send
Packet on port "awc0" (error=0x00000041)
Mar 16 06:21:21 [ip address omitted] last message repeated 9 times

Similar Messages

Netctl, ip and drivers issue for ethernet and wlan

Hi,
I recently installed the version of archlinux with netctl instead of netcfg.
During the installation I think I've used netcfg and it was all running smoothly. Then I wanted to configure my connection on the system, but it's impossible in all the ways I tried. I followed the beginner's guide then copied the wireless-wpa profile from the examples folder to the netctl folder, then
sudo netctl start profilename
. I've also
sudo ip link set wlp4s0 up
but then i got with the show option:
3: wlp4s0: <NO-CARRIER, BROADCAST, MULTICAST, UP> mtu 1500 qdisc state DOWN mode DEFAULT qlen 1000
link/ether 68:a3:c4:df:17:8e brd ff:ff:ff:ff:ff
I get the same result with enp2s0. I've already run dhcpcd.
Then I controlled drivers. I have a ralink rt5390 card and it's using rt2800pci. Ethernet card it's realtek rtl8111/8168 and is using r8169. How can I connect to the internet? I need it, thanks in advance.
Ps: sorry for my terrible English, I'm Italian
Last edited by shoyip (2013-05-21 12:56:36)

I'm not on my Arch machine at the moment, but let's see if we can fix this.
For the moment, try setting up your wired connection first. If you are sure your wired device's name is [enp2s0] then (run as root):
You might want to kill DHCPCD before starting.
# systemctl start dhcpcd@enp2s0 <---this is to enable DHCP for your wired connection
# systemctl enable dhcpcd@enp2s0 <---this is to enable DHCP automatically at boot
# dhcpcd
You can also refer to network-configuration page.

I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either

I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either it says that i have a newer bootcamp version. I tried a few tricks but they didnot work. I hope to be helped

Welcome to Apple Support Communities
You can install a 64-bit Windows 7 or Vista version in your Mac. Make sure you downloaded these drivers > http://support.apple.com/kb/DL1630 Also, if you have the Snow Leopard DVD you used to upgrade your Mac or the OS X DVD that came with your Mac, you can use it to install the Boot Camp drivers

Failed Hardware Scan and other issues E440

Hi all,
This is probably more rant than anything, but I wanted to give a heads up to others too.
I have a ThinkPad E440 that is a year old. From the very first time I turned it on, there have been issues. The first hardware scan (via Lenovo Solution Center - LSC) showed a warning for the Intel Dual Band Wireless-AC 7260 Local Connection Test. There were also tons of System Events that always show up in the "Configuration History" part of the LSC. You can look at the calendar and tell exactly which days I used the computer because there will be System Events generated each day. Things like app crashes and failed drivers.
In July 2014, I got the first warning for the 16 GB SSD - the SMART Short Self-Test. By February this year it showed as failed for each hardware scan (these were initially set up to run monthly).
Also the whole time I've had it the touch screen would just stop working at some point and I would have to reboot to get it working again.
I finally called Lenovo on March 30th, before my warranty expired. When I called that time, I didn't realize the hard drive failure was the SSD. So they sent me a new 500 GB drive. I also added the other things into the case when I talked to them. For the wireless issue they suggested making sure the driver was up to date. I did this and let them know when I called back that it was up to date and still having the warning. So I called them to tell them to tell them about the wireless and also that I realized it was the SSD having the failure, not the main drive. The first case had already been closed even though none of the other items were addressed.
So they opened another case (this is #2). They said to mail them the laptop since the wireless issue would probably be on the board and it wasn't something I could fix myself. They sent a box with a prepaid overnight shipping label. I was very sick for a few days so I sent it back to them on April 10th (a Friday). Via UPS I saw it was delivered on Saturday. Work was performed on it Monday, April 13th and sent back to me that very day. I received it on April 14th. This part of the service has been excellent - very fast response.
Being in IT, I included a letter with the laptop that outlined the issues that should have been in the case. I also printed the hardware scans and what the system events looked like.
When I got the laptop back, the sheet inside said they had replaced the Speaker because of Distorted Sound. This was not even on the list even though I had noticed it. I didn't even power up the laptop before calling them again - yes, I was furious! Plus our power was out...
So this was noon on the 14th. They opened case #3 and sent me ANOTHER BOX so I could send it back.
After our power came back on the 15th, I powered up my laptop. I opened the browser (I have it set to restore the previous session) and there was a sexually explicit video on YouTube. I opened the other browser and there was a different video on YouTube. So this person was watching YouTube instead of fixing my laptop. I looked through both browser histories and there was quite a bit of activity while my laptop was at the repair center... I ran the hardware scan - still failed and a warning for the wireless. They really hadn't done anything.
I also found two pictures of the repair person in the recycle bin...
So I called back. I was LIVID! They opened another case (this is #4). And sent me ANOTHER BOX. I finally learned the other day that once a case is opened, it cannot be edited or added to at all. Instead, they close the other case and open a new one. I guess their turnaround time for closing cases is excellent! I've never seen a system like that - and I've used a lot of them.
I got a really nice, patient fellow on the line. He took all my info (again). I emailed him the pictures, screen captures of the YouTube videos, the letter I had sent - everything. He entered as much into the new case as he could - he talked to one of the supervisors to make sure he did it right. Somehow he flagged it so that the laptop would get more attention (time) at the repair facility. He also opened a separate case (an escalation ticket?) for a supervisor to call me regarding the person's conduct at the repair facility. He said they would call me that day. (It's now the 25th and I've never heard from anyone)
So, he sent me ANOTHER BOX. I've built up quite a stack of them.
Our power was out AGAIN from the 17th through the 19th (don't get me started).
I noticed a hardware scan had now gotten a failure on the main hard drive. So I called them on the 21st to add this to the case before sending the laptop back. The girl said they can't add anything to an existing case or edit it at all once it's opened. She would have to open a new case and SEND ME ANOTHER BOX. I told her to forget it because I was ready to send it in and didn't want to wait for another box. I also asked for a status on that "escalation case" where the supervisor was supposed to call me. In order to do this she, yes, wait for it, had to open ANOTHER CASE!! So they would know I wanted a status. I'm completely dumbfounded.
So I sent it back on the 21st. This time I practically wiped it. I had already removed all my files the last time, but I had left my bookmarks and browser history intact. I set up a guest logon with admin privileges. I updated my letter and printed off more stuff to include with the box. On one sheet I had only the case number, the serial number and machine type. On another sheet I had "DO NOT SEPARATE THIS PAPERWORK FROM THE LAPTOP" and the case number. I put this sheet on top (The guy on the 15th said my letter and stuff may have gotten separated from the laptop once it was delivered to the repair facility). I used a ton of staples so it would all stay together. I included in my letter the failure on the main hard drive and asked if they could look at it. I wrote about having to open a new case if I wanted to include it.
They received it on the 22nd. A nice gentleman from the repair facility called me that day asking about the password. that. was. written. on the sheet they have you fill out. I told him what happened last time and also mentioned the hard drive failure and asked if he could look into it. He said they would.
I received my laptop back yesterday morning.The sheet that came with it said they had "replaced the following parts to complete the repair of your laptop."
Part Description                                           Symptom
IMAGE                                                             Replaced due to engineering change
System board                                                 Network card error
Hard disk drive                                                Network card error
ECA-WIRELESS                                            <no symptom listed>
There was also a sheet saying they had installed a factory preload of software and I needed to install Lenovo and Windows updates.
When I booted it up, the first thing I noticed, in the lower right corner was:
Windows 8.1
SecureBoot isn’t configured correctly
Build 9600
I ran a hardware scan. Well, I tried. It stopped part way through and said it finished successfully but most of the tasks showed up as cancelled. I tried to run it again - issues - rebooting ensued. It said the LSC wasn’t available and that I should try again or reboot.
Tried several times. Then got what I guess is the new BSOD - kinder, gentler:
Your PC ran into a problem and needs to restart. We're just
collecting some error info, and then we'll restart for you. (xx% complete)
If you'd like to know more, you can search online later for this error: DRIVER_CORRUPTED_EXPOOL
Even though the LSC said my Lenovo files were all up to date, I ran the Update. And first I had to download a new version of Update. Then I downloaded all of the Lenovo updates and installed them (there were quite a few). The BIOS update failed. While I was doing the Lenovo downloads, I got a light blue screen but no text (I was out of the room so I'm not sure what happened). Did CTRL-ALT-DEL and it shows only IE and Task Manager as applications that are running. Could not “Switch to” IE. Hitting window key to go to start didn't do anything. So I had to restart.
By 3pm yesterday there were 34 system events in the configuration history.
I ran the hardware scan again after I updated the Lenovo files, and you guessed it! Failure on the SSD (SMART Short Self-Test) and warning on the wireless. Nothing had changed. Except hardware scan is acting different than it did before I sent in the laptop for repairs. When it finishes, it instantly closes and just shows 100% complete. When I click on "see last results" it shows a screen called
Log Information,
Canceled 04/24/2015 n:nn pm
You have not done a hardware test on your computer
And the calendar in LSC only shows the very first hardware scan I did on Friday. Even the hardware scan screen shows the date and time of the last scan. It also shows the error code. In order to see exactly what is failing, I have to sit there and watch it very closely and snap a picture of the screen as soon as the error (or warning) shows up.
When I would try to run Windows update, it would hang up PC Settings. I couldn't even kill it using task manager because it didn't show up as a task. During this, I got a flag saying the firewall wasn't turned on. I tried to turn it on, but clicking on Turn on Windows Firewall didn't do anything. I tried to setup my Microsoft account but that just hung too.
I ended up running Windows Update FOUR TIMES to get all the updates installed. Every time I ran it, it said "Done!" and I would run it again and more would show up. The last time was this morning.
At some point, the error about SecureBoot went away.
Then, I created a bootable BIOS update disk. Following the ReadMe instructions, I went through ThinkPad Setup and verified several values. Of note:
Secure Boot was DISABLED. According to the ReadMe file, this should be ENABLED in Windows 8.1. I enabled it.
Under Startup/Boot, according to the ReadMe that came with the BIOS update, UEFI/Legacy Boot is supposed to be set at UEFI Only for Windows 8.1. Mine was set to "Both". I changed it.
In Startup, OS Optimized Defaults was DISABLED, even though it says right there (and in the BIOS update ReadMe) it should be ENABLED to meet Microsoft Windows 8 Certification Requirement.
After these updates, I flashed the new BIOS.
Then, I ran hardware scan again...
Now I have TWO failures on the SSD: Random Seek Test and SMART Short Self-Test. Great.
In the Event Viewer (that I recently discovered), it says my disk has a bad block. It just says The device, \Device\Harddisk\DR1, has a bad block. I assume this is the SSD...
There are 867 events in the event viewer - Critical, Error, and Warning...
Fifty-two of these are from October 7, 2013 - before my little laptop was a glimmer.
The rest are from when Lenovo had it and yesterday and today.
64 of them are the disk error.
341 are from DeviceSetupManager. 65 of those are from failed driver installs. 69 are for not being able to establish a connection to the windows update service. 64 are from not being able to establish a connection to the Windows Metadata and Internet Services (WMIS).
3 times it's rebooted without cleanly shutting down
60 of them are from Service Control Manager and say The TDKLIB service failed to start due to the following error: The system cannot find the file specified.
One of them says {Registry Hive Recovered} Registry hive (file): '\??\C:\Users\Default\NTUSER.DAT' was corrupted and it has been recovered. Some data might have been lost.
16 are warnings that various processors in Group 0 are being limited by system firmware.
12 say the certificate for local system with thumbprint <bunch of hex numbers> is about to expire or already expired.
108 are warnings for failure to load the driver \Driver\WUDFRd for various devices
16 are application errors
One is for the computer rebooting from a "bug check"
15 are for name resolutions timing out after none of the configured DNS servers responded.
10 are for SecureBoot being disabled.
14 for services terminating unexpectedly
15 are for WLAN Extensibility Module has stopped
61 are for applications not being able to be restarted because the application SID does not match Conductor SID
12 are for activation of CLSID timing out waiting for the service wuauserv to stop
So, I'll call them on Monday and open. a. new. case (#5?) - but really 7. And get A NEW BOX.
I'll keep you updated!

Hi amycdero and welcome to the HP Forum,
I understand that you are having scanning and printing issues after upgrading to Mavericks OS X v10.9.1. I will try my best to help you resolve this issue.
In this document for Mac OS X: Scanning Software Does Not Open or Stops Responding are steps the may help you with your scanning issue.
This document for Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems should help with the streaking printing issue.
I hope this information is helpful. Please let me know.
Thank you,
I worked on behalf of HP.

IQ826t Restart and Heating Issue

One thing I definitely do not like the HP's support especially when they will not allow us to buy a 7 Upgrade from Vista nor will they support something (even when I find their glitches and they admit after telling me it was just the OS).. On Repair work, I had to ship it out and this will be my 2-3 time to do repair on this PC in the past 3 years (and I have to wait a week for the repair to be done...)
Besides that, IQ826t, Win 7 Ultimate SP1
All Drivers are up to date with HP website (utilizing Win 7 64 bit drivers and Firmware is up to date). AVG update/scan (no issue - confirmed even rootkit).. Malwarebyte - Scan and no issue
Disk Cleanup, Disk Defragmentation done on a monthly and quarterly schedule
Biggest Issue:
I am getting a crash with Win 7 0x124 Stop Error Message (happens periodically and even after a reboot)
Never had this issue until May and the upgrade to Win 7 was done last year with SP1 update done on March (so it is not an issue with the OS as HP support personnel seems to think... I proved them the issue with Windows Update History, The Bluescreen error code on my error code reader).. This machine under warranty and I had issues with it constant (even in Vista)
They state that it is the OS.. Again, if that was the case, I would think it would happen right away like my Toshiba on SP1 upgrade... That was not the case in the matter. I have a firmware reset (default settings) and the issue persist..
The Error Code relates always HAL.dll or ntoskrnl.exe
One if hardware compatiblity and the other is an OS kernel exe file.. And this usually checking knowledge base relates to hardware failing due to 1) Compatibility (which HP website confirms is not the case) 2) OS corruption (which is not the case checking on safe mode and this happening STILL 3) Heat Issue (which I believe is the issue and was been documented on the Internet
What I am noticing is the unit is extremely HOT (vent is almost burning when it has been off and just turned on).. I wonder if the hardware pieces are literally melting to destruction since I can't just open it up (they state it will void my warranty)
The Symptoms before the Crash (happens any time.. Even right after a power up)
If you are playing audio or video, you will start to hear jitters and sound seems to echo itself .. Video would start to lag and become choppy.. Systems start to slow down and things seem to run very slow.. I have seen the power light on the PC start on but the touchscreen just go black (will not restart sometimes)..
Minor Issues (but could be related)
1) When running PC Hardware Diagnostic, they will come up with an error code in the past and that was warranted for a motherboard replacement (of course, they ship the box to the wrong location and I was in the middle of my wedding so I get to it now).. It was pertaining to PCI Express Status ICH9 PCI Express Root Port where it will generate an error code... Now, running the diagnostic... I will not get any error but PCI Express Root Port 3 & 5 do not show up on the diagnostic... Wouldn't that obvious show something that is a problem when there are 6 ports (which on the previous diagnostic that I can't grab past logs shows that). That is not warranted for a warranty work? Just a note, I got the fail test code (which was intermittent but keep happening and the tech support would not look at previous case.. Port 4 failed and a fatal device code)
2) Blu-Ray player will not run and their answer is that it is your Blu-Ray until they realize that I ran it on 3 different Blu-Ray player standalone, different Blu-Ray, and confirm DVD will work.. They still think it is a software issue until they can't deny my point when it will not read the Blu-Ray no matter what (they took control and confirmed it).. They believe the HP SmartDVD software was failing because of Win 7 and not Vista (even when I downgrade and confirm it works, I stated the software is the issue... Lone and behold, 2 months later they had an update that they refuse to admit I was RIGHT on the matter and done 15 hours of troubleshooting that they were wrong about)
3) Wireless Keyboard and Mouse lost connectivity even if the battery is not low... Just stop typing or omit letters.. This is considering the keyboard is literally in front of the touchscreen
4) Touchscreen is sensitive when it wants to be but won't in other... Constant issues there
This is why I have so much issue with support.. They seem to show that they will do anything to deny the issue.. Heck, I am a computer technian calling on the issue.. It ain't like I didn't troubleshoot on the matter... But they think we are all morons and when I prove them wrong, they will use any excuse to honor warranty... That is why it is amazing..

Look in your Settings > App Manager.
Tap Device Monitor.
Tap the Battery tab.
At the upper right, tap "Since Last Charge" to change to "Last 48 Hours".
What apps or processes are consuming the most battery power?
ALSO, in setting up your new Z30, are you syncing many contacts or calendar data from a connected email account?
Social accounts such as Facebook or Twitter?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

C6180 All In One Photosmart. Software and drivers will not install on Windows 8.

C6180 All In One Photosmart
on
Windows 8 64bit
Acer Aspire V5-552PG
AMD A10- 5757M
Radeon HD 8750M dedicated
Software and drivers package will only unpack but not install.
When the unpacking bar reaches the end, it disapears without any following actions.
I have of course tried it over again many times, and I have deleted the download and redownloaded it again but the same happens every time.
Any idea on how to solve this?
Sincerly
FLFO

HI FLFO:
I have done some research on your post. I have found a document with steps to help resolve the stall you're experiencing during your printer installation.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00836418&tmp_task=solveCategory&cc=us&dlc=en&lc...
Happytohelp01
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Windows 7 and photosmartD5460 issue

I have a photosmart D5460 and windows 7 after i installed win7 i could not print anymore on DVD's
uninstalled and installed again got other drivers to print covers on dvd nothing is working can anyone help?

Leeopard huh?
You need Snow Leopard w. 10.6.x to get 3.0.
If it works and no issues fine though probably the first time I have read someone did.
BC 2.2 was more about XP and some support for Vista.

Logic 6 and Tiger Issue

I just upgraded to tiger, from panther.. I'm still using logic pro 6, and after 3 days of erratic behaviour (long long start ups amongst other dialogue boxes), now it wont start up at all.
I also use a motu 828 mkII, and have installed the latest tiger drivers for this product, to no avail.
If anyone wants to know, i really don't think it's compatible with tiger, and although i was going to upgrade anyway as soon as i could, now i have a problem..... do i go back to panther in order to finish my tune? what a waste of time! Shame there wasnt a warning from apple..so i do it for you.

Nathan Pangburn, "Logic 6 and Tiger Issue" #3, 11:38am Oct 26, 2005 CDT
Be aware, there is one bug that I know of with Logic Pro 6.4 and 10.4. If you try to change a song's metronome settings, Logic will crash.
I think that's the only known issue.
The workaround is to create songs in 10.3 with the desired metronome settings and use them as templates in 10.4.

Creating executable including run time and drivers windows 7

Hi
Using version 8.5.1 and need to include the runtime version, and drivers for connecting to scope into an executable. Have found so much information on the subject of creating an executable but would like to know if anyone has some step by step for version 8.5.1 to create an executable. Also, has anyone had any issues with drivers and installing/creating exe. while running windows 7.

Hi!
I remember running the compiler at home on Windows 7 64bit using 32bit LabVIEW and I did not have any problems. The exe built just fine.
You have to have your code in a project in order to build an executable. Once you have created a project and included your source files, right click on Build Specifications and choose "New->Application (exe)". Go through each section of the Application (exe) dialog and input the appropriate settings you need.
You can include the runtime and device drivers by creating an Installer. Once you have your executable built, you can right click on Build Specifications and choose "New->Installer". Same thing, go through each part of the dialog box selecting appropriate settings. Under "Additional Installers" you can include NI drivers and the LabVIEW runtime. If you have never done this before, it may ask for you to insert LabVIEW/NI Driver discs so it can include what it needs to for your installer.
My users tend to groan whenever I do this, however, as it creates installers >400MB (which seems silly to them for what appears to be a simple program). Ah well.

Windows 8.1 Audio and Video issues

I recently updated Windows 8 to 8.1 on my 2012 MacBook Pro and it now appers that Headphone/Line In have stopped working.
This only occurs in Windows mode, when running in OS X Mavericks the issue does not occur so I am assuming that it is a driver related issue rather than hardware.
I also have an issue with dual monitor setup, if I attempt to change the resolution or go from Dual to Single then back again, it fails to locate the second monitor again. Once again, this all worked with no issue before the 8.1 update and no issue occurs while running OS X.
Has anyone else experienced these issues and/or know how to resolve them?
I have gone through device manager and it indicates that all drivers are up to date.

i too have the same issue. I did a fresh Bootcamp install of Windows 8.1 64-bit on my mid 2011 iMac and my built in audio and headphones have stopped working on the Windows side. OSX Maveriks is ok.
i also went to the device manager and all of my audio drivers are up to date...still no sound.
i have uninstalled and reinstalled all audio drivers, disabled then enabled them several times...still no sound.
i have unistalled the graphics driver (i read somewhere else that there was an issue with it)...but still no sound.
can someone help us out?
NOTE: i have a usb audio dongle that works on windows. but it only controls my headphones. when i plug in the headphones into the built in audio jack on the iMac it doesnt work.

Access Connections 5 and up issues

Hi,
For years our organization has been using Access Connections 4.52 flawlessly. Recently we purchased a boat load of R500 notebooks. At this point, we were forced to upgrade to version 5.20 as 4.52 will not recognize the wireless card.
With 4.52, when a client would boot up wireless and attempt to login to our network , Access Connections would pop up, then attempt the login only AFTER it has connected to the network. With 5.20, 5.33 and 5.50, this function seems to work ok until I sysprep the image.
After I sysprep our image, this is what happens: User boots up wireless and attempts to login to our network....gets and error stating "OURDOMAIN is not available"....15 seconds later Access Connections wakes up and connects to the wireless network. Now, here is the really dumb part. I can resolve the issue on my image by opening Access Connections > Location Profiles > Select Profile > Edit > OK. Access Connections will now behave properly, until I sysprep.
Is there any solution out there for this? Or even better, is there a way I can make 4.52 work on a newer model. 4.52 did not have this issue.
Thanks
Rosy

Hi,
I cannot see it being fair, to blaim Access Connection for situation, that is clearly not caused by Access Connection.
In the past I was working with multiple corporate images, which I of course had to create, which included syspreping the image. And I can tell you, that sysprepping a 100% working image is always, and I really mean ALLWAYS screwing up some part of the image. If you have been doing images for longer time, then surelly you will be agreed with me.
If you are not, then you have not created enough images manually (I mean starting with the times of RIS, going through WDS, IUB, SCCM .... ).
So much for understanding, where to look when you are looking for the root cause.
So Access Connection is a tool, that depends on other applications and driver. Almost the same as by all other TVT applicaitons. For Access Connection it's highly important, that it's installed in following order together with other tools/drivers:
1) Power Managerment driver
2) Power Manager
3) System Interface driver
4) Hotkey utility/driver
5) LAN Driver
6) WLAN driver
7) WWAN driver
8) Access Connection
It's highly important, that this order is kept.
So back to the imaging, here is what might happen, when you sysprep the image:
- you sysprep it, where some parts (usually ini files) are remoted from the dirver installed on the machine.
- of course you configure the sysprep to load up all the drivers depending on the HW, or some input from the client
- this will load everything back and inclusiv all the drivers
ISSUE:
- WLAN, driver is installed/inicialized after Access Conenction was present in the image
- by syspreping some of the above menitoned applications from Lenovo are taken as drivers and therefore, they are re-installed only after sysprep kicks-in
I'm pretty sure, that you know, how you install you image and by some points you might not be agreed with what I'm writing, but I was working with the informations, that I could find in your description.
I think more description on the sysprep, or the imaging tool and structure might help me imagine, what is goin on.
BTW: I just remembered, that by olders versions of AC 2.x and 3.x when such issue was present, like also LAN was not detected and all this happened after I installed a corporate image, then my fix for the image was quite simple:
Reinstall all the above drivers + apps in the order as you can see it in here .
Cheers

NIK and Photoshop Issues

I've had a need to use my various NIK software quite a bit more, than I normally do, and doing so has uncovered a ton of issues for me. I previously had these issues, but not to the same degree that I do now.
My work flow is to import images into LR3 as RAW from a Canon (5D MkII or 40D), make minor adjustments in LR3, and then export to PS CS5 as 16-bit ProPhoto TIFFs. I normally start with Dfine, then on to Viveza2, and then Color Efex Pro, collapse my layers, save and return to LR3. I can usually repeat this process without any issues. Now, I'm finding that I can repeat this process maybe 2 or 3 times, before something goes wrong. By wrong I mean, I'll have to click multiple times on "Add Control Point" button in Viveza2, before I get the crosshair to drop the point. I frequently have to double or triple click in the location, just to be able to drop the point, otherwise it's "sticky" and follows the mouse, although I'm not holding the button down. Furthermore, once the point is dropped, if I click on a slider, it may not respond respond at all, or if it does respond, it's "sticky" in that I can't release it. At this point, I know that Photoshop needs to be quit and restarted. However, clicking on the "Cancel" or "OK" buttons, doesn't work, or if it does, there is a very long delay. I usually "Force Quit" Photoshop. I can reproduce these issues repeatedly in Viveza 2 and Silver Efex Pro. I don't recall having any issues with the other NIK software applications.
I have had issues with Photoshop unexpected quitting as well, when I'm not in a NIK application. For instance, I may be using the Healing Brush or Clone Stamp, adjusting a Curve or something. I don't recall if I'd previously used a NIK product before the unexpected quit.
To resolve these issues, I've run Apple's Disk Utility, checking for permission and disk related issues. I've also run DiskWarrior for the same issues, though none are found. I've removed the entire NIK suite of applications, uninstalled Photoshop and reinstalled it, as well as removing my mouse and Wacom drivers. The problem persist with just the Wacom software installed, without having the Razor Pro software installed.
Using an iMac 27", with 8GB RAM, 10.6.5, and the most current versions of all other software and drivers.
Ideas, thoughts, suggestions?

I don't have a script as such -- but the installer cleanup tool helps after doing an uninstall.
See http://www.adobe.com/support/contact/cs5clean.html
And the initial release of Photoshop did have some bugs, which is why we put out 2 dot releases.
And MacOS has had a few dot releases to fix bugs that were affecting Photoshop as well, and they still have more to go.

Finder and iTunes issues.

This past week or so, iTunes has been force booting itself at seemingly random times.
This has been causing me issues when I am working on video or audio projects, as when iTunes boots it eats almost all of my RAM and causes most of my programs to lock up, even if only temporarily.
When this happens Finder eventually loses connection to my LAN and ejects my external hard drives. When I try to reconnect to them, the operation either times out, it says the drives can't be found or that my LAN isn't running. I should note I'm using an AirPort Extreme base station to create my LAN and share my drives.
To try to solve this, I have tried force quitting Finder, but then it won't start again, instead citing some error code.
This again becomes a problem when trying to shut down as Finder is required to complete the process. The only way I can get around this is to force reboot my computer by holding the power button down until my MacBook shuts itself off.
Immediately upon reboot, all programs that were affected by iTunes and RAM loss take an EXTREMELY long time to finish booting.
All my software and drivers are up to date.
I'm running OSX 10.6.8 on a late 2010 MacBook 2.4GHz Intel Duo core.
AirPort is Extreme 2nd version running version 7.6.1
==Update==
It seems two reboots are required for my drives to show up over my LAN.
After the forced shutdown and reboot it doesnt work.

I've gotten everything running again, but iTunes still persists in force booting itself when I don't ask it to.
I've checked my sync and update settings on my iTouch, but it still does it.
I've gotten past the Finder force reboot issues by just telling my computer to reboot when my network is experiencing difficulties.
This has also solved the issue of said drives and network not showing up again upon reboot.
Programs still take ages to boot if they were not quit properly (ie. iTunes caused massive lock up and programs had to be force quit), and this is still affecting my work flow negatively.

Software and Drivers for an HP Scanjet 5590 with a 64 bit Windows 7 computer.

I thought that I had posted the following question but as I can't find it I will try again. I have been given a HP Scanjet 5590 scanner with no Software or Drivers for 64 bit Windows 7 computer and looking through the Web I saw some awful comments on the experiences of those using the software and drivers. I don’t want to make the same mistake so could anyone tell me how to go about obtain the correct software and drivers?

Corporal,
Here is the link for the software...
If you have the "p" model, backtrack a the link and reselect the proper model.
You want the "Full Feature" software.
Note that the download size is 315MB - plan accordingly if you have a slow connection...
While you are there, be sure to download the Print Doctor utiltity. (Do that first, it is tiny.) This may help later with installation and connection issues, if needed.)
HP Scanjet 5590 Digital Flatbed Scanner series - Software and Drivers
I hope this helps...
   Click the White Kudos Star on the Left to give Kudos for the help.
       Please Click “Accept as Solution” to say issue is solved.
Always Include: (Computer) Product Number , Printer – Model Number ,
                             Never give out your Serial Number
                              2012 Year of the Dragon!
Kind Regards,
Dragon-Fur

How to configue AirCel prepasd SIM Card and drivers for 8.1 64bit

Hi Team Members,
how to configue AirCel prepasd SIM Card and drivers for 8.1 64bit
issuse in my laptop
Sarfaraz
(Personal information removed)

@Sarfaraz71 ,
Thank you for posting and the HP support forum and welcome.
So that I can help you better with your sim card issue. Could you post back with your.
Full Model and Product Number
Second in your post you asked about Windows 8.1 drivers and you state you are running Windows 7.
What Operating System are you running.
Hope to hear back from you soon with the information I have requested.
Have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

Br350 - Diversity and drivers issue

Similar Messages

Maybe you are looking for