Camera Sensor Error Post Production Fix

I have a number of shots which include a sensor error.
A large number of shots from this shoot were dropped due to a slow motion camera error associated with its Current Session
Reference (CSR).
This basically creates a different slightly darker top to bottom on each frame.
The different in tone occurs exactly half way across each frame
Could anybody suggest a post production fix?
Maybe even involving third party plug ins?
I need a fix which would analysis each frame and unify the tone of each full frame.
Even a suggestion to a forum / site which I could possibility find some help on this issue, would be a huge help as I have 200 plus shots
which need to be fixed.
Please find attached an example screenshot
Thanks

Thanks for your suggestion Mylenium. I have tried Re:Match but unfortunately it hasn't fixed the error. Would you have any other suggestions, that you think would be worth trying?

Similar Messages

PCG and Windows error - how I fixed

I'll make this post in the hope it might help others.
I was a sufferer of, and an early contributor to, one of the long running PCG error threads.
After several years of successful Premier/Encore authoring with a successful workflow I suffered the dreaded PCG error not long after upgrading to Encore CS3. After a lot of trial and error and help from these forums I finally solved the issue by getting brand new hardware and installing Adobe Premier/AE/Encore/Audition and nothing else on the box. Same workflow and assets, no problems. This rather suggested to me it's not Encore itself that's the problem, nor necessarily the workflow or the assets, but more that some complex interaction within Windows somewhere was responsible. In my case I had a project with 5 timelines, each on a menu, and each timeline had it's PCG solved (before I switched hardware) by a different combination of the 'fixes' suggested here.
On the new hardware same assets/project/workflow - no issues.
At the weekend I was happily knocking out a quick slideshow of a wedding I shot recently when Encore failed at the Create Disc stage with a 'Encore has encountered an error and neads to close' message. Not only did my current project fail, but one that was working a few weeks ago failed also. This strongly suggested it wasn't an asset/workflow issue.
On investigating further I realised that I'd broken my own rules about being rigerous and not installing anything other than Adobe on my PC. As part of sorting out my monitor profiling (specifically the ability to profile each monitor in a dual setup independantly) I'd downloaded and installed a Microsoft 'Colour' feature. It installed itself but also the .NET framework as well as +C++ runtime environment.
I uninstalled all three items and Encore sprang back into life building and burning both the older project as well as my new one.
All of this confirms to me that the problem that Encore presents with is caused by a pretty fundamental interaction somewhere in the bowels of Windows and that whilst the actions of fiddling with settings or assets or any of the other 'fixes' that work for some people some of the time are not really addressing the fundamental problem.
My advice would be to install Adobe video products on a fresh install of Windows and run them and nothing else. Observe 'profession IT' standards of configuration management and things should be OK.
It's not how we maybe envisage running a PC but the hard practicalities of our complex friend make it so.
Hope this helps someone else.
Regards
Pete

Wow.
It's probably deeper than that. I have both the .NET framework and the latest C++ runtime installation from Microsoft, and I cannot reproduce this error even if I handle my assets badly.
Rodger Ling may be correct. This may be some deep hardware/software conflict that only appears on certain hardware configurations when certain other software is involved.
Unfortunately, that would make it nearly impossible to track down the bug and squash it without some serious user input on *complete* hardware and software configurations.
Thanks for posting your fix; likely it will help someone else who runs into this issue.
-Jeff

Error on Production Server when php service is called.

The web application runs fine on my development machine but on the production server it gives me the following error and no responce when a phpservice is called.
error:
Send failed
Channel.Connect.Failed error NetConnection.Call.BadVersion: : url:
'http://ipaddress/Project/public/gateway.php'
Network Monitor:
Development Machine:
Windows 7
MySQL 5.5.16
Zend Framework 1.10
Production Machine:
Ubuntu 11.10
MySQL 5.1.58
Zend Framework 1.11
I followed the following steps to deploy the application on production server;
1. created identical database with same credentials on the production server
2. confirmed that my php service works on the server by manually navigating to the php file and printing the data retrieved on the page
3. modified the paths in amf_config.ini to reflect production server
[zend]
webroot = "/var/www"
zend_path ="/usr/local/zend/share/ZendFramework/library"
library ="/var/www/Project/library"
services ="/var/www/Project/services"
[zendamf]
amf.production = true
amf.directories[]=Project/services
4. initialized the class by adding
// Initialization customization goes here
_serviceControl.endpoint = "http://ipaddress/Project/public/gateway.php";
in the .as file for the php service
I have also found from my zend server logs that when my php service is called its throws the following error:
PHP Notice: Undefined index: HTTPS in /usr/local/zend/share/ZendFramework/library/Zend/Amf/Response/Http.php on line 59
I doubt that there is anything wrong in the deployment process but please do let me know if you could think of something i might have missed.
The other thing im wondering is the php notice if it were to be caused due to different Zend Framework versions!
Kindly advice

EGJ Steens has post a fix at http://forums.adobe.com/message/4097998#4097998#4097998/Using Flash Builder
Zend framework 1.11 added an extra function in the Http.php file (which was mentioned in the post) and was fixed as follows
protected function isIeOverSsl()
        $_SERVER['HTTPS'] = 'off'; //Adding this line fixed the issue
        $ssl = $_SERVER['HTTPS'];
        if (!$ssl || ($ssl == 'off')) {
            // IIS reports "off", whereas other browsers simply don't populate
            return false;
        $ua = $_SERVER['HTTP_USER_AGENT'];
        if (!preg_match('/; MSIE \d+\.\d+;/', $ua)) {
            // Not MicroSoft Internet Explorer
            return false;
        return true;
My concern is if i wish to secure my application with ssl using HTTPS will this prevent me from doing so.
Any Pointers Anybody?

Graininess: How to filter it out in post-production?

Hi, all,
I've just imported 3 nights' worth of footage with iMovie HD 6. The camcorder was unmanned the first night (sadly) and the second night I noticed quite a bit of graininess (probably due to the lighting of me being way in the back dimly lit, and the subject being up front with some overhead lighting.) Fixed that up with the camcorder settings for the 3rd night (after visiting www.hv20.com).
Soooo.... is there any way to fix up the footage from the first two nights in post-production with iMovie HD 6? Are there any settings to look at within the app (I'm new to it.) Are there any plug-ins or another app entirely that would help?
Thanks so much!
Deborah
PS in iMovie 08, you can just pick a clip and boost the sound up to 200% Is there a similarly easy way to boost the sound in iMovie HD 6?

consumer camcorders do some marvel: they work in a bright sunlighted winter landsacpe, and with the 'light' of 3 candles under the chrismas tree.
when doing nightshots, your camera rises the gain extremely => 'grain'/noise.
I don't know of any effect, which allows to 'vanish' that.. adding a slight blurr to that scenery would erase the noise, but.. < caugh > blurrs the pics. (this is a widely discussed issue for still photographers too = same probs, even with pro tool Photoshop ..)
there's a free tool http://www.xs4all.nl/~jeschot/home.html#JVC claiming to reduce noise.. never used it, try on your own..
you can raise the volume by rasing the 'rubber band' in the audio track.
some people recommend, to copy/paste the same audio track, which should improve level (never tried).. iMHD6 has limits in audio processing, an export of audio only into some audioapp as Garageband or Audacity and a re-import into your IM project is recommended.

Remove water spot on lens in Post Production

I've looked around but haven't seen this question yet.
Can I remove a spot that was on my your lens while I was shooting and remove it in post production?
I have CS4 and FCS 2 to work with.

Yes, very nice. Thank you.
But, do I have to go get footage of a grey card? Reason I ask, is because I only rent cameras and don't own a nice one to begin with. Plus, this is only for the board of directors over at Virgin America. Is there a way to add a gray matte instead? Nob questions, sorry.
It was a raining day on the 14th in the early morning. My camera had a bag but water still got in.
Ughh, its also in too many shots to fix it.
I'll post it here when I'm done.
Oh Les, I was gonna add you on Facebook but couldn't find your profile. Do you have Facebook or LinkedIn by chance?
Thanks for you help.
Jesse Dean (facebook)

Valuation with material cost estimate: error with product " 200038 "

Hi,
I am getting an error:
Valuation with material cost estimate: error with product " 200038 " (Message KE350).
Kindly assist on the same?

If this material is mto material go to t.code KE40 and maintain define access to standard cost estimate define cost key with
"Transfer sales orde cost estimatex".
If it is mts material define costing key with Transfer std cost estimate and in costing data
costing variant : ppc1
costing verstion: 1
period indicator: Release std cost estimate matching with goods issue or material costing matching posting date.
This will resolve ur problem.

Error in Production Load: Error passing data to port

Hello All,
I got this unexpected error in production. The Jobs are still processing for a long time(in Yellow status) with the error message :
Extraction (messages): Missing messages      (Status:Yellow)
     Missing message: Request received      (Status:Yellow)
     Missing message: Number of records sent     (Status:Yellow)
     Missing message: Selection Completed     (Status:Yellow)
Transfer (IDocs and TRFC): Missing messages or warnings           (Status:Yellow)
     Request IDoc : Application document posted                (Status:Green)
     Info IDoc 2 : sent, not arrived ; Error passing data to port      (Status:Yellow)
     Info IDoc 3 : sent, not arrived ; Error passing data to port      (Status:Yellow)
     Info IDoc 1 : sent, not arrived ; Error passing data to port      (Status:Yellow)
I went through the below forumn, and asked the basis to look in to it. In the meantime can any one please suggest me any solutions.
Some problem with IDoc's Settings while loading data

Hi Ram,
The problem may be with the connection to the source system you are loading the data from. You can check the connection using the note 140276.
Best Regards,
Des.

I am using Mac OS X 10.7.5 as of now and when I am trying to upgrade to Mavericks, it is throwing error "The product distribution file could not be verified. It may be damaged or not signed".

I am using Mac OS X 10.7.5 as of now and when I am trying to upgrade to Mavericks, the App Store is throwing error "The product distribution file could not be verified. It may be damaged or not signed".
Is there anything I should do differently? Is anyone else facing the same issue?
Kindly help.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then copy it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click anywhere in the line of text below on this page to select it:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}' | open -ef
Copy the selected text to the Clipboard by pressing the key combination command-C. Then click anywhere in the Terminal window and paste (command-V). I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting. A TextEdit window will open with the output of the command. If the command produced no output, the window will be empty. Post the contents of the TextEdit window (not the Terminal window), if any — the text, please, not a screenshot. You can then close the TextEdit window. The title of the window doesn't matter, and you don't need to post that. No typing is involved in this step.
Step 2
Repeat with this line:
{ sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|cups|isc|ntp|postf|x)/{print $3}'; echo; sudo defaults read com.apple.loginwindow LoginHook; echo; sudo crontab -l; } 2> /dev/null | open -ef
This time you'll be prompted for your login password, which you do have to type. Nothing will be displayed when you type it. Type it carefully and then press return. You may get a one-time warning to be careful. Heed that warning, but don't post it. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
{ launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)/{print $3}'; echo; crontab -l 2> /dev/null; } | open -ef
Step 4
ls -A /e*/{cr,la,mach}* {,/}Lib*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts .la* 2> /dev/null | open -ef
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of login items' | open -ef
Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

XML errors message (Product key not found/Invalid) in SNC5.1

Hi,
I am working on SNC project which includes POC scenario.I have completed all the required configuration in R/3 4.6c and SNC5.1 system. The master data (mat, plant,vendor and Info records) are CIFed from R/3 to SNC, BP and MoT created in SNC. All the MD BAdIs are implemented in SNC. I am trying to post a PO from R/3 to SNC, IDOCS are successfully generated, PI has converted the IDOCS into XML messages, but i am getting XML error in SNC system (sxmb_moni) which states-
1) Product key 000000000123456 (category ID) not found
2) Item 00001: Product is missing or invalid
3) Order, item 00001: Product 000000000123456 does not exist
4) BOL processing failed. XML-message inbound processing has been terminated.
I am able to post the PO successfully in SNC Web UI which has alpha numeric product number (eg- 1120-110), but products with numerical value leading zeroes (eg- 000000012345) do not get posted. These product IDs give error in SNC sxmb_moni.
I have set up the output format of product number with 40.
Appreciate your help.
Is there any kind of configuration required for leading zeroes in any of the systems (R/3,PI or SNC)
Appreciate your help.
Regards,
Edited by: Dmohite on Jun 11, 2009 11:09 PM

Hi Bharath,
Were you able to over come the error for products in the XML message? I have same issue, can you please briefly point me in right direction?
I am facing the error message " Product key 0000000000xxxxxxx (category ID) not found". can you please briefly mention how did you resolve?
In my case, the XML message had product number '000000000070000598' and I tried to implement BAdI to make the product number appear as '70000598' and still it failed.
Thank you in advance
Best regards
Vivek
Thank you in advance.
Best regards
Vivek

Bridge not saving toning/applying post production - like 20K images to tone!!

Hi - Am desperate - have 10 weddings to do post production on and my bridge is acting up.
I am having a bridge isssue - when I apply the toning/cropping/color correction to images and press done it is not saving the work. In addition when I do the work in bridge and then choose save as it just save them as untoned JPGSs. It does not apply the raw conversion or xmp data.
In addition it is only happening in half the images in the folders not all of them. And it's not camera specific it's random.
Any help would be greatly appreciated.
[email protected]

I am having a bridge isssue - when I apply the toning/cropping/color correction to images and press done it is not saving the work. In addition when I do the work in bridge and then choose save as it just save them as untoned JPGSs. It does not apply the raw conversion or xmp data.
Bridge is only a file browser without editing capacities (except the export panel but that has been discontinued in Bridge CC) and reflects the content of your folders. If you make changes in ACR using either selecting via PS or via Bridge any changes should be visible wether you have hit done or save in ACR.
If you have other results, especially random difference it looks like a cache problem to me. So point the Content panel to a problem folder and use menu tools / cache / purge cache for folder and check if this solves your problem.

Sensor Error during Apple Service Diagnostics

I've been having problems with my early 2009 mac pro freezing and having to hard reboot. I ran Apple Service Diagnostics and the test fails during Sensor tests:
Temp (TNOD) - (MacPro) IOH or (iMac or mac mini) MCP, Tdiode (test 1) - Sensor Reads Within Operating Range
- Check to ensure that sensor reads within operating range.
ERROR - Sensor is reading above the high limit
- TEST FAILED -
Does this mean I need to replace the logic board?

Putting in the new logic board solved my issue, but I assume if I just fixed the loose sensore it would have fixed it for a lot less.
I attached a pic for you pointing it out on the processor board.

How to White balance in post production

I am working on a project that was used by two cameras, but one of the cameras white balance is different than the other. Is it possible to match the white balance in post production in final cut express so that the video quality looks very similar (without one seeming bright orange than the other)? Thank You for any help with this topic.

FCE has a Color Corrector in Browser>Effects>Color Correction>Color Corrector.
When you adjust one cameras clip to match the other you can copy and paste attributes to other clips
Al.

White Balance & Post Production

Hi,
My client gave me an interview she conducted to edit. The white balance is horrible. Is there anyway for me to fix this problem during post-production? I've been playing around with color correction and desaturation.
I'd appreciate any feedback.
Thanks
Power MacPro Mac OS X (10.4.1)

How much time do you have to turn this project around? In the Peachpit Apple Training Series, there is a training book titled "Advanced Color Correction and Effects in Final Cut Pro 5" that is an excellent resource for this.
It teaches you how to color correct using the four FCP scopes to get it right.
The Auto White function in Color Corrector 3-Way will put you in the ballpark IF there is a white object in the shot. If not, then you're on your own.

Error connecting to sensor. error loading sensor.

Hi all,
I have brand new ASA 5525-X firewall and IPS Security Services Processor ( ASA5525-IPS). There is no any configuration in both devices. I try manage the both device using ASDM-IDM. I can able to access the firewall using default management IP address. But while i try to access IPS
"Error connecting to sensor. error loading sesor" massege is coming. I try to ping IPS management ip address from my pc but i unable to ping.
Please any one can help me to resolve this issue.
ciscoasa(config)# sh module
Mod Card Type                                    Model              Serial No.
0 ASA 5525-X with SW, 8 GE Data, 1 GE Mgmt, AC ASA5525
ips ASA 5525-X IPS Security Services Processor   ASA5525-IPS
Mod MAC Address Range                 Hw Version   Fw Version   Sw Version
0 7c69.f68f.b2b3 to 7c69.f68f.b2bc 1.0          2.1(9)8      8.6(1)2
ips 7c69.f68f.b2b1 to 7c69.f68f.b2b1 N/A          N/A          7.1(4)E4
Mod SSM Application Name           Status           SSM Application Version
ips IPS                            Up               7.1(4)E4
Mod Status             Data Plane Status     Compatibility
0 Up Sys             Not Applicable
ips Up                 Up
Mod License Name   License Status Time Remaining
ips IPS Module     Enabled         perpetual
ciscoasa(config)# sh module ips details
Getting details from the Service Module, please wait...
Card Type:          ASA 5525-X IPS Security Services Processor
Model:              ASA5525-IPS
Hardware version:   N/A
Serial Number:
Firmware version:   N/A
Software version:   7.1(4)E4
MAC Address Range: 7c69.f68f.b2b1 to 7c69.f68f.b2b1
App. name:          IPS
App. Status:        Up
App. Status Desc:   Normal Operation
App. version:       7.1(4)E4
Data Plane Status: Up
Status:             Up
License:            IPS Module Enabled perpetual
Mgmt IP addr:       192.168.1.2
Mgmt Network mask: 255.255.255.0
Mgmt Gateway:       192.168.1.1
Mgmt web ports:     443
Mgmt TLS enabled:   true
Regards,
Manimaran.

Hello Mani,
The network setup on this modules is different than previously so my recommendation is follow the next link, determine which will be your network setup and finally configure everything as properly
http://www.cisco.com/en/US/products/sw/secursw/ps2113/products_tech_note09186a0080bd5d03.shtml
Then U should be good,
For more information about Core and Security Networking follow my website at http://laguiadelnetworking.com
Any question contact me at [email protected]
Cheers,
Julio Carvajal Segura

Errors in Production

Hi Friends,
Pls any one send me Errors in production with solutions.
Regards
Ramana

hi ramana
HI,
"Job Termination in the R/3 Source System
u2022 The Exact Error message is ""Job termination in source system"". The exact error message may also differ, it may be u201CThe background job for data selection in the source system has been terminatedu201D. Both the error messages mean the same. Some times it may also give u201CJob Termination due to System Shutdownu201D.
u2022 The message appears in the Job Overview in RSMO, or in u201CDisplay Messageu201D option of the Process in the PC.
" "u2022 If the job in R/3 system cancels due to some reasons, then this error is encountered. This may be due to some problem in the system. Some times it may also be due to some other jobs running in parallel which takes up all the Processors and the jobs gets cancelled on R/3 side.
u2022 The error may or may not be resulted due to Time Out. It may happen that there would be some system issues like locks/DB Issues in the source system
" "u2022 First check the job status in the Source System. It can be checked through Environment -> Job Overview -> In the Source System. This may ask you to login to the source system R/3. Once logged in it will have some pre-entered selections, check if they are relevant, and then Execute. This will show you the exact status of the job. It should show u201CXu201D under Canceled.
u2022 The job name generally starts with u201CBIREQU_u201D followed by system generated number.
u2022 Once we are confirm that this error has occurred due to job cancellation, we then check the status of the ODS, Cube under the manage tab. The latest request would be showing the QM status as Red.
u2022 We need to re-trigger the load again in such cases as the job is no longer active and it is cancelled. We re-trigger the load from BW.
u2022 We first delete the Red request from the manage tab of the InfoProvider and then re-trigger the InfoPackage.
u2022 Monitor the load for successful completion, and complete the further loads if any in the Process Chain.
"Transact RFC Error u2013 Non Updated IDOCs in the Source System.
u2022 Message appears in the bottom of the u201CStatusu201D tab in RSMO. The error message would appear like u201CtRFC Error in Source Systemu201D or u201CtRFC Error in Data Warehouseu201D or simply u201CtRFC Erroru201D depending on the system from where data is being extracted.
u2022 Sometimes IDOC are also stuck on R/3 side as there were no processors available to process them.
" u2022 tRFC u2013 Transact Remote Function Call Error, occurs whenever LUWu2019s (Logical Unit of Worku2019s) are not transferred from the source system to the destination system. "u2022 Once this error is encountered, we could try to Click a complete Refresh u201CF6u201D in RSMO, and check if the LUWu2019s get cleared manually by the system.
u2022 If after u201Ccoupleu201D of Refresh, the error is as it is, then follow the below steps quickly as it may happen that the load may fail with a short dump.
u2022 Go to the menu Environment -> Transact. RFC -> In the Source System, from RSMO. It asks to login into the source system.
u2022 Once logged in, it will give a selection screen with u201CDateu201D, u201CUser Nameu201D, TRFC options.
u2022 On execution with u201CF8u201D it will give the list of all Stuck LUWu2019s. The u201CStatus Textu201D will appear Red for the Stuck LUWu2019s which are not getting processed. And the u201CTarget Systemu201D for those LUWs should be the BW Production system. Do not execute any other IDOC which is not related have the u201CTarget Systemu201D.
u2022 Right Click and u201CExecuteu201D or u201CF6u201D after selection, those LUWu2019s which are identified properly. So that they get cleared, and the load on BW side gets completed successfully.
u2022 When IDocs are stuck go to R/3, use Tcode BD87 and expand u2018IDOC in inbound Processingu2019 tab for IDOC Status type as 64 (IDoc ready to be transferred to application). Keep the cursor on the error message (pertaining to IDOC type RSRQST only) and click Process tab (F8) . Ths will push any stuck Idoc on R/3.
u2022 Monitor the load for successful completion,
and complete the further loads if any in the Process Chain.
"No SID found for a characteristics
For example consider a Transactional Data load has failed due to no SID found for the characteristic 0Customer." It might happen that the Master Data 0Customer was loaded much before the transactional data load and by the time the transactional data load was started some transactions has taken place in the OLAP sytem and a new Customer has got created. As a result the Transactional Data load which would try to get the SID for the master data would not find it would fail. Check for the Master data in the R3 system if the data is available in the R3 system load the Master data in BW and then manually load the transactional Data. If the master data is not present in the R3 system also then itu2019s a data issue and needs to be reported to OSC or the Client.
"Attribute Change Run failed - ALEREMOTEBW was locked.
u2022 The message appears in the Job Overview in RSMO, or in u201CDisplay Messageu201D option of the Process in the PC.
u2022 The exact error message would be like, u201CUser ALEREMOTE locked the load of master datas for characteristic 0CUSTOMERu201D. Here it is specifically for the 0CUSTOMER load. It may be different related to Master Data InfoObject which is getting loaded. " During the Master data Loads, sometimes a lock is set by the system user ALEREMOTE. This happens because the HACR is runnning for some other MD load at the same time when the system tries to carry out the HACr for this new MD. This is scheduling problem as due to the time clashing the error has occured. "
u2022 Check the error message completely and also check the long text of the error message, as it will tell you the exact Master Data which is locked by user ALEREMOTE.
u2022 The lock which is set is because of load and HACR timing which clashed. We first need to check RSA1 -> Tools -> HACR, where in we would get the list of InfoObjects on which HACR is currently running. Once that is finished only then, go to the Tx Code SM12. This will give you few options and couple of default entries. When we list the locks, it will display all the locks set. Delete the lock for the specific entry only else it may happen that some load which was running may fail, due to the lock released.
u2022 Now we choose the appropriate lock which has caused the failure, and click on Delete. So that the existing lock is released.
Care should be taken that we do not delete an active running job. Preferable avoid this solution
u2022 When HACR finishes for the other Master Data, trigger Attribute change run fot this Master Data.
No Data found in the soucre system It may happen that there is transaction which has taken place for particular load. Or incase of delat loads there is no changes. This would result in giving anerror message as "No data available in the source system". As a result the load would remaing hanging ie the QM status would be yellow and if not changed then the load would fail due to processing overdue. Extract the data in the source sytem and check whether the data is actually present or not. If the load is getting the data from a flat file go to the Application server i.e transaction AL11 and go to the relevant path and check whether if data is present. If data is not present then change the QM status to manually green. If the data is available check for the extractor job failure.
srinivas reddy
Posts: 40
Registered: 7/11/07
Forum Points: 0
   Re: errors
Posted: Jun 13, 2008 3:41 PM    in response to: Shashank Dighe       E-mail this message      Reply
can u tell me the solutions for above lock issues, no app found data , idoc/trfc errors
Bala Murugan A.J
Posts: 462
Registered: 9/27/07
Forum Points: 864
   Re: errors
Posted: Jun 13, 2008 4:10 PM    in response to: srinivas reddy       E-mail this message      Reply
1) IDOC or TRFC Error
We can see the following error at u201CStatusu201D Screen;
Sending packages from OLTP to BW lead to errors
Diagnosis
No IDocs could be sent to the SAP BW using RFC.
System response
There are IDocs in the source system ALE outbox that did not arrive in the ALE inbox of the SAP BW.
Further analysis:
Check the TRFC log.
You can get to this log using the wizard or the menu path "Environment -> Transact. RFC -> In source system".
Removing errors:
If the TRFC is incorrect, check whether the source system is completely connected to the SAP BW. Check especially the authorizations of the background user in the source system.
Analysis:
If we see at the error message we find that the failure is due to Non-arrival of IDOCs from Source System to BW.
Action to be taken:
Reload the Master Data manually again from Info-package at RSA1.
2) PROCESSING IS OVERDUE FOR PROCESSED IDOCs
Diagnosis
IDocs were found in the ALE inbox for Source System that are not
Updated.
Processing is overdue.
Error correction:
Attempt to process the IDocs manually. You can process the IDocs
manually using the Wizard or by selecting the IDocs with incorrect
status and processing them manually.
Analysis:
After looking at all the above error messages we find that the IDocs are found in the ALE inbox for Source System that are not Updated.
Action to be taken:
We can process the IDocs manually as shown below:
3) ERROR AT SOURCE SYSTEM ASKING FOR REPLICATION OF DATASOURCES
Analysis:
If we see at the error message we find that the System is asking us to Replicate the Data Source System.
Action to be taken:
Go to RSA1 initial Screen & press Source System tab at LHS.
Once Replication is done we have to activate the Transfer Structures in Production System. For this we have to execute a program SE38 in BW On executing we will get the following screen:-
Once you have Replicated the Data-Sources & Activated the Transfer Structure you can reload the data manually by Executing the Info-package at RSA1.
4) LOCK NOT SET FOR LOADING MASTER DATA ( TEXT / ATTRIBUE / HIERARCHY )
Reason for Failure:
Diagnosis
User ALEREMOTE is preventing you from loading texts to characteristic
0COSTCENTER . The lock was set by a master data loading process with the
request number (DataPcakage number)
REQU_3VB1GNF0FGRRV84IUWGFOIIG7(000001) on 20041001,071055(985111) .
System response
For reasons of consistency, the system cannot allow the update to continue, and it has terminated the process.
Procedure
Wait until the process that is causing the lock is complete. You can call transaction SM12 to display a list of the locks.
If a process terminates, the locks that have been set by this process are reset automatically.
Analysis:
After looking at all the above error messages we find that the user is u201CLockedu201D.
Action to be taken:
Wait for sometime & try reloading the Master Data manually again from Info-package at RSA1.
5) DATA ERROR
Analysis:
After looking at all the above error messages we find
1st u2013 That it is a PC File Source System.
2nd - That there are Duplicate Data Records leading to error.
Action to be taken:
We have to delete this Request & then rectify the Data in the Data source at the Source System Level. After this we have to manually load the data.
6) OTHER TYPE OF DATA ISSUE
l Error Message
Diagnosis
1 data records were marked as incorrect in the PSA. The additional checking and processing of the 2 data package was terminated in a customer routine. This was done intentionally or was due to a short dump being intercepted.
System response
The data package was not updated.
Procedure
Correct the incorrect data records in the data package (for example by manually editing them in PSA maintenance). You can find the error message for each record in the PSA by double-clicking on the record status.
Analysis:
After looking at all the above error messages we find that the PSA contains incorrect record.
Action to be taken:
To resolve this issue there are two methods:-
i) We can rectify the data at the source system & then load the data.
ii) We can correct the incorrect record in the PSA & then upload the data into the data target from here.
Resolution: - We will see how to do the go for the 2nd method: -
7) ERROR WHILE LOADING PC FILE FROM DESKTOP / APPLICATION SERVER
Analysis:
After looking at all the above error messages we find
1st u2013 That it is a PC File Source System.
2nd u2013 For uploading data from the PC File it seems that the file was not kept at the application server & the job was scheduled in Background.
Action to be taken:
For running the job in Background Transfer file to Application server & then load it from there.
OR Else if you want to load file from your desktop then donu2019t schedule the job in background instead select u201CSchedule Immediatelyu201D option in the Info-Package.
8) JOB FAILURE AT SOURCE SYSTEM
Analysis:
Diagnosis
The background processing was not finished in the source system.
It is possible that the background processing in the source system was terminated.
System response
There are incomplete data packets present.
Further analysis:
Go to the background processing overview in the source system. You can get to this with the Wizard or the menu path Environment -> Job Overview -> In the source system (This is the alternate path to see the u201CJob Overviewu201D at the Source System.
Once there, check whether the background job really was terminated.
Note
Please make sure that the correct date of request has been selected in the selection screen of the overview.
Action to be taken:
At source system you can see the reason for the Job Failure. Thus we need to take the action accordingly.
9) ERROR ASKING FOR INITIALIZATION
Analysis:
After looking at all the above error messages we find that if we want to load data with the delta update you must first initialize the delta process.
Action to be taken:
If you want to load data with the delta update you must first initialize the delta process.
Afterwards the selection conditions that were used in the initialization can no longer be changed.
But Initialization is a typical process that should not be carried out without confirming with the onsite person in any case.
10) ERROR RELATED TO ACTIVATION
Analysis:
Here we can see that the Activation of ODS has failed as the Request Status in the ODS may not be green.
Action To be Taken:
Go to RSA1 Select your ODS Object  Right Click on it & Select u2018Manageu2019.
Select the Red Request & see the reason for its failure.
Rectify the error & then go for its activation.
Error message when processing in the Business Warehouse
Diagnosis
An error occurred in the SAP BW when processing the data. The error is documented in an error message.
System response
The error message(s) was/were sent by:
Second step in the update
Second step in the update
Second step in the update
Second step in the update
Procedure
Check the error message (pushbutton below the text).
Select the message in the message dialog box and select the long text for further information.
Follow the instructions in the message.
11) TRANSACTION JOB FAILES GIVING MESSAGE : u201CNO SID FOUND FOR CERTAIN DATA RECORDu201D
Action to be taken:
Load Master data KU. To load it, select its Infopackage & at schedule tab select u201CImmediateu201D & start loading.
After this come to RSMO & select this failed job.
Click on Detail tab.
Since in this case we see that the data is only getting loaded in ODS & not in PSA thus we have to reload data manually through Infopackage.
If we have PSA here then we need to take the following action:
1) Expand nodes under Detail tab.
2) Expand node u201CProcessing (data packet): Everything OKu201D
3) Right click on u201CData Package 1 : Everything OKu201D under it.
4) Select Manual update option in the dropdown menu.
Hope it helps

Camera Sensor Error Post Production Fix

Similar Messages

Maybe you are looking for