Can't configure both WAN ports on 1811 with SDM

Hi,
We recently procured an 1811 router to replace a SOHO linksys at a store we service. We needed redundant WAN interfaces to use the DSL as a backup to the main cable connection, and a Linksys RV082, while doing the job when it actually worked, died repeatedly. We decided after looking at the 1811's feature set to just get the Cisco and be done with it and not monkey with SOHO gear anymore.
Where I'm having difficulty is SDM won't let me configure both WAN interfaces from the GUI, it only allows me to configure one. I have it configured, and the router is working nicely in the test lab but I need to get that other interface configured and failover enabled before I can put this thing into production.
What am I doing wrong? Do I need to suck it up and learn IOS?
Thanks,
Todd Phipps
Certco, Inc.

I ended up figuring out the IOS commands to enable one fastethernet port as a primary and the other one as a backup (running both cable and DSL for redundancy; it's a grocery store that runs electronic transactions over IP so 100% availability is a must).
The trouble I was running into in SDM is that while it would allow me to configure one WAN port through the GUI, the config options for the second one were grayed out. Now that both are configured through IOS the edit buttons for both WAN interfaces appear normally in SDM. It's almost as if Cisco didn't want users to be able to configure both interfaces graphically for initial setup.
Now just to test it at the site before the store opens to see if the failover works...
Todd

Similar Messages

  • Can you configure a static port to use with certsrv.msc?

    I am trying to use certsrv.msc to connect from my workstation to the CA for administration purposes.  Workstation is Win7, CA is 2008 R2 Enterprise running Enterprise Subordinate on a dedicated box.
    I configured a static DCOM port for certsvc by following this article, including bouncing the service and also rebooting the CA box:
    http://social.technet.microsoft.com/wiki/contents/articles/1559.how-to-configure-a-static-dcom-port-for-ad-cs.aspx
    The static port was opened in the firewall from my workstation to the CA.  We also found that TCP 445 was required, so that has been opened as well, port 135 & other ports normally needed for autoenrollment should be open.  Sniffing the firewall
    showed that a random high numbered port that is not the static dcom port is being attempted - this is the only port showing dropped packets & no traffic on the static port.
    I am wondering if there is a way to configure a static port for this high-level random port to use with certsrv.msc as I was able to do with the certsvc dcom port?  I am trying to avoid having tens of thousands of network ports wide open going to my
    CA...  Thanks in advance!

    Hi Steve,
    I am sorry that I wasn’t able to find references about restricting certificate services only use one port in the random port range.
    However, we can configure RPC dynamic ports allocation to restrict port range. In the meantime, we should keep at least 100 ports open to keep necessary system services running.
    More information for you:
    How to configure RPC dynamic port allocation to work with firewalls
    http://support.microsoft.com/kb/154596/en-us
    Service overview and network port requirements for Windows
    http://support.microsoft.com/kb/832017/en-au
    Firewall Rules for Active Directory Certificate Services
    http://blogs.technet.com/b/pki/archive/2010/06/25/firewall-roles-for-active-directory-certificate-services.aspx
    Best Regards,
    Amy Wang

  • Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

    Can the Gigabit Ethernet LAN Port be used with a Thunderbolt to Gigabit Ethernet adaptor and then to a Thunderbolt Hard Drive as a back up drive?

    If you use ethernet to connect the two AirPort Extremes together, you'll have Gigabit speeds available at all of the ethernet ports on both routers.
    If you connect the second AirPort Extreme using wireless only and configure the Extreme to "extend a wireless network", then the maximum speeds that the second router can attain will be limited to the capability of the wireless connection. So, if you connect at normal "n" wireless speeds of say 130 Mbps, that will be the maximum speed available at the ethernet ports on the second AirPort Extreme.
    I think you can easily see the difference between Gigabit ethernet, which is 1000 Mbps compared to "n" wireless at 130 Mbps. Even if you can manage to connect at 5 GHz speeds for wireless, the max speed will be in the 300 Mbps range, more than 3 times slower than Gigabit ethernet. Normal "n" speeds will be about 7 times slower than ethernet.
    For streaming high definition video and other demanding sources, you'll need as much bandwidth (speed) as you can get. Ethernet is always the best choice if you can possibly use it. And...there's no wireless interference on an ethernet connection.
    Message was edited by: Bob Timmons

  • Can I access both platforms, window and mac with one cloud account

    can I access both platforms, window and mac with one cloud account

    Yes.
    One Cloud membership = 2 software activations: Win/Win or Mac/Mac or Win/Mac.
    http://www.adobe.com/au/products/creativecloud/faq.html
    "Are there any unique benefits that come with my paid membership?
    Yes, as a member of Creative Cloud, you get many benefits that you do not get when you purchase a traditional shrinkwrapped product:
    Access to both the Mac OS and Windows® versions of the desktop applications and the ability to install them on your primary computer and one backup computer. So, if you have a Mac at home and a PC at work, you can install your applications on both as long as they are not running at the same time. See the product license agreements page for more information."

  • Can I upgrade both of my Intel computers with the same CD

    Can I upgrade both of my Intel computers with the same CD

    According to apple's licence agreement you can only install it on one machine. The 10.6 family pack which has 5 license is also available.

  • Configuring Ethernet 'WAN' port on AirPort Extreme

    I would like to know if there is any way to configure the Ethernet MAC address on the WAN port of the AirPort Extreme.
    This is a feature available on most other brands to accommodate the lock-down to the first Ethernet MAC address that the ISP encounters on their port.
    Quickly replacing one router with another requires the ability to set this address. Otherwise, lengthy support calls are needed with some service providers to reset equipment on their end.

    Even if you can't spoof a mac address with the Apple networking products, why not just call your cable company/ISP and give them the new mac address? That's all I had to do in order to switch from Linksys products to all Apple products.
    The ISPs do this because it's their little way of trying to control traffic thru each of the modems but only allowing for one device to be connected to it at a time.
    I'm wondering why you would keep switching back and forth between routers? I would think that when you do change routers, you'd want that to be a 'permanent' change and not a temporary one.

  • Can't configure tacacs-server port

    We're unable to configure a specific port, which is required for our customer for the tacacs-server.   One of the devices is a 7604 router running this image -
    c7600rsp72043-adventerprisek9-mz.122-33.SRD6.bin.  The other device is a 2960 switch with the following image - c2960-lanbasek9-mz.122-35.SE5.bin.
    We don't get the option to add a port after the tacacs-server host x.x.x.x command. 
    Any ideas would be greatly appreciated!
    Regards..

    Hi
    Please go through this link, this will be helpful regarding TCSACS Authentication and Fortigate configuration:
    http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/acsuserguide.html

  • Can you run both the latest Safari along with 4.0 beta?

    I'd like to play with the Safari 4.0 beta, but can't afford to lose my regular Safari along with its bookmarks, bank links etc.
    Can I run both on the same machine and just start up whichever one I want?
    P.

    Is there any possibility that the new Safari-4beta is causing my menus to freeze-up? I find my menu bars are often dead and I have to switch to another program-- even those are sometimes dead too, and after 30 seconds one comes to life, then they all do, but then go back to frozen again.
    I wouldn't put anything past Safari 4. Its mere presence causes the currency converter widget to give wrong answers.
    I tried to use the uninstaller, but it would not work; then I tried to just install Safari 3.2.1 - but it would't do this "Can't install since you have a newer version on your Mac"-- Safari 4 Beta did NOT do this on TIGER- but this was my weekend to switch to Leopard after 13 months of prepartion...
    If the unistaller won't work, I don't think there is any way to get back to the old Safari without either reinstalling OSX, or restoring from Time Machine (using the Utilities menu on the Leopard install DVD) and choosing a backup before you installed Safari 4.

  • Can i configure each ethernet port to fixed and auto ip adresses?

    Hi, i will be using a SSL Matrix Controller with Logic 9. This connects thru ethernet and requires a FIXED address. However, this Mac also needs to connect to the internet which doesnt use a fixed a address. Can I keep port one the way it is, and configure port two as fixed and have them both work properly? Are they completely independent of each ther?
    Thx

    Do you use a Router that you control?
    If so, you can have fixed addresses easily -- just assign an address Manually that is in the same range, but above or below the ones your Router is likely to pass out automatically.
    You can also assign a manual address to the second Ethernet port, but using it this way is complex. What does the device maker recommend?

  • Can I use the WAN port on my AirPortExpress to extend my WiFi from my Time Capsule?

    OK folks, here's what I want to do.  I have a Time Capsule not only supplying WiFi, but also connected to the ethernet in my home.  What I want to do is use the ethernet to connect my AirPort Express and extend the WiFi signal.  I've tried various settings configurations and the closest I get is a duplicate network.  This causes problems for Home Sharing of iTunes accounts to my 2 Apple TV's, one that is connected to ethernet and the other WiFi.  Plus, it seems to confuse our iPhones and another WiFi computer from time to time.
    So can this even be done, is there another option I'm missing? We are trying to use this in a room for the AirPlay feature and the original WiFi signal drops pretty regularly, so moving it closer to the TC is a last resort.
    Thanks in advance for the help!

    Hi - if what you want to do is have the Express produce a wireless network with a new name then you need to configure it in the following way - it should be set to connect via ethernet in bridge mode and set to "create a wireless network" with a new name and password of your choice - if you need specific steps let me know.

  • Can't configure EM 10.2.0.3 with EMCA, wrong password

    Hello,
    I have a 2 node RAC.
    Used the following to create the EM :
    emca.bat -config dbcontrol db -repos recreate -cluster
    STARTED EMCA at 3-dec-2007 16:23:59
    EM Configuration Assistant, Version 10.2.0.1.0 Production
    Copyright (c) 2003, 2005, Oracle. All rights reserved.
    Enter the following information:
    Database unique name: PSDBPRD
    Listener port number: 1521
    Cluster name: PSDBPRD
    Password for SYS user:
    Password for SYS user: Invalid username/password.
    Password for SYS user:
    Password for SYS user: Invalid username/password.
    Password for SYS user:
    Password for SYS user: Invalid username/password.
    Password for SYS user:
    Password for SYS user: Invalid username/password.
    Password for SYS user:
    Password for SYS user: Invalid username/password.
    Password for SYS user:
    But the password is ok, I can open an sqlplus with this sys / password combination with no problem. But emca does not work.
    I also created the password files again.
    any ideas ?
    Thanks,
    Kristof

    I am having the same issue. Did you ever find an answer?
    EM works, log in as sys user and password with NORMAL - I get in.
    If I try As SYSDBA- it says invalid username/password.
    From SQLPLus - the user name works and lets me in (with / as sysdba or not)
    SQLPLusW - sys user and password - lets me in.
    I cant create the EM because it requests the sys password with it will not accept.
    Is there a way the passwords are out of sync?
    Paul

  • How can I configure a third party VME board with A24 address space using a VME-MXI-2?

    Hi!
    We are trying to establish communications to a Galil Motion controller with a VME interface. Galil states that they are using a A24 address scheme with A16 data space for their board.
    I am confused how to configure that board in the VME chassis properly.
    The base address provided by Galil is 91Fxxx, I am assuming that the lower three nibbles are the registers that I can talk to?!
    How do I set the address range under the resource setting for that board?
    Also, I noticed in MAX that one board shows up with a slot number unknown, one with slot #0 and this board I have set to slot #1. I assume that the unknown part is for the PCI card that makes up for the 1/2 of the PCI to VME bridge?
    The VISA VIs (Register based access) returns either a bus error, an invalid offset specified or data. However, we are completely in the dark when it does return data, since the expected offset we are typing in causes one of the two errors.
    Our assumption of the problem is that we do not understand how to properly configure that third party board as a resource. It has also happened that the resource manager is hanging up the PC completely. Not even CTRL-ALT-DEL works and the MXI activity LED on the NI-VME-MXI-2 board stays on during the hand up.
    We would appreciate, if somebody could walk us through the configuration process, step-by-step. Specifically, please explain how to setup the base address and how the offsets relate to this on a A24 address scheme. We are completely new to the VME bus interface, so even trivial things may be unkown to us.
    We have browsed NI's page and manuals for explanations, however, we could not find any answers to our questions.
    We noticed a formula for an A16 board that takes the base address and adds the logical address to it plus 40hex. Do we have to do the same or something similar to the A24 board????
    We also came accross an option that would allow the board (NI VME controller) to share its memory with A24 or A32 space? Do we need to enable that? What is the purpose for that?
    Best,
    Markus Tarin
    www.movimed.com - Custom Imaging Solutions
    www.movitherm.com - Advanced Thermography Solutions

    When I did not get a response here, I had to open a ticket with support.  The short answer is that you cannot customize the SAML response when using Azure AD as an IdP.
    Response from support:
    I discussed the issue with senior engineers to get action plan for this issue. After doing research Senior engineers updated me that we cannot add a custom attribute to the default
    SAML response of Azure AD.
    Below is the link to get the list of available attributes
    https://msdn.microsoft.com/en-us/library/azure/dn195587.aspx
    As default SAML response from Azure AD , we have email address of the user sent out as attribute value for the Attribute " NAME ".
    They suggested me to configure the application we are trying to integrate with Azure AD in such a way that it transforms the Attribute  " NAME " into " EMAIL
    This was not particularly helpful in my case as I did not have any control over the 3rd party which specifically documented that they would not extract the email address from the name attribute.
    Cheers,
    Jeff

  • Can I install both CC and CS6 apps with my Creative Cloud membership?

    Yes, you can download CS6 apps from the Download Center on creative.adobe.com. Click any app icon. From the product download page, for instance Illustrator, look for the heading "In this version" and click the version pop-up menu beneath it to select CC or CS6. The big blue Download button at the top of the page changes to "Download CS6".
    Note: It is fine to have both CS6 and CC apps on your computer. Some users require mutliple versions for different clients, etc. Its a personal preference, but in no way is a requirement to uninstall your CS6 apps in order to install CC apps.
    Tip: From the Creative Cloud destop app, click the "More Information" link under any app to be taken directly to the product download page.

    Go into your CC Desktop app: Find new apps, change "All" to "Previous Version".
    Click on Install next to Photoshop and CS6 will be an option.

  • Can we configure the system to create order with reference ony?

    Hi,
    Do you know if we can do anything in the sales order type configuration to force the system not allow to create the sales order without reference?
    Thank you.

    Yes, You can do that. Go to define sales document type and select proper drop down in reference mandatory field. You can create with reference of sales order, quotation etc

  • How can you configure a WD external to work with Time Machine??

    I have an 1TB external WD MyBook drive that is connected to my network through my Linksys wireless router and am trying to figure out how to format the drive to use with Time Machine.
    I currently use the drive to store files from both my PC and my MacBook but can't seem to select the drive to use with Time Machine. I figured that I could just format the drive through the Disk Utility program, but the drive doesn't show up in Disk Utility. This may be because it is a drive connected through my router and not directly to my MacBook?!
    Here are a few questions...
    Any ideas on how to format the drive so it will work with Time Machine?
    Once formatted to use with TM, can I still use the drive to store other files from both my Mac and PC? or do I need to partition for this??
    Is it possible to set up an automatic backup schedule that will happen via my home wireless connection?
    Thanks in advance,
    Todd.

    You cannot use the drive with TM as you have it set up. TM will not work with a networked drive except a Time Capsule or a USB drive connected to an Airport Extreme Base Station (current version.)
    If you wish to use this drive for TM backups it must be connected directly to the computer. Other computers on the network can access the drive for TM backups if you turn on file sharing for the drive (select drive, press COMMAND-I, check the box labeled "Shared Folder," click on the Enable button.) The shared drive will have to be mounted on the other computers in order for them to use it as a TM backup drive.

Maybe you are looking for