Can't establish cable connection between mini and TC

I recently had to restore the system on my mini.
it is now in a 'just purchased' state.
previously i backed up everything wirelessly (even the initial backup),
so now i have the most recent working backup on my TC.
NOW i want to restore the system from TC to its recent working state.
but it seems i can do it only wirelessly, as hooking up mini and TC via Ethernet cable won't help mini see the TC.
I turn off AirPort on my mini,
connect TC's LAN port to mini.
Turn on TC.
In my Network Settings
Ethernet properties are:
Location - Automatic
Status - Connected (active and has the IP address 192.168.1.12)
Configure - DHCP with manual address
IP Address - 192.168.1.12
(DHCP can be left automatic with the only difference that
Status says CONNECTED, BUT since the 'IP is assigned automatically, Ethernet MAY NOT be connected' - have no idea what this MAY NOT means, although when i unplug the cable, Ethernet connection disappear from the list)
Now the Time Machine doesn't see any devices as the source of backup.
What am i doing wrong?
i can still run the time capsule wirelessly, but as far as i remember the initial (wireless) backup of approx 80 gigs took more than 24 hours... i'm not that patient anymore.
Please help.
Thank you.

Similar Messages

How to establish the connection between crm and r/3

Hi,
Sorry for posting this question in this forum, i did not find any CRM forums.My question is,How to establish the connection between CRM and R/3...in my office i installed standard alone CRM system,but it is not talking to R/3.
Could any one tell me where to find adapters and plugins for this.
Thanks in advance.
Ajey

Hello Ajey,
in the case you mean the connection between R/3 and SAP CRM you should read the Best Practice Guides:
B01: CRM Generation
C71: CRM Connectivity
B09: CRM Replication
from http://help.sap.com/bp_crmv240/index.htm. There is a CRM Forum at http://www.sap.com/community/ and also at http://www.sapfans.com/.
Regards
Gregor

Can't establish wireless connection between the printer and computer.

I recently upgraded my wireless to an Apple AirPort Time Capsule. I'm able to set up the printer via USB cable. And I'm able to set up the printer on the network via the Airport WPA utility. However I cannot establish a wireless connection between the computer and the printer. When I go to the printers window in my system prefereces, there is no wireless printer available to add in the "available printers" menu. Only the USB version printer is listed and of course when I disconnect the USB cable it shows as offline.I've tried all the fixes on HP's support pages. I've tried reinstalling the printer on both the router and the computer numerous times. The only thing I haven't done is reinstall the printer using the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download). And when I reset the printer to factory settings, then connect it to the computer via the USB, there is no installation software that pops up. Cant even find the **bleep** thing in "Finder". (I'm assuming that it should show up as some sort of external device.) I've checked to make sure both computer and printer are on the same network. (sometimes my computer will grab a connection with the next nearest network.) I've checked all the settings for the printer via the HTML configuration utility. I've even updated my Macbook software and restarted it multiple times. Note: the printer actually worked for a bit when I first switched routers, but the printer's wireless function went offline several times and then quit altogether. Really frustrated that I bought another HP product thinking this time things would be different. HP is no help unless you want to pay $$ for a phone call. I'm about ready to take this thing out in the desert to use for target practice and never buy another HP product ever again.

Hi , I saw your post regarding the problems you are having with your LaserJet Pro P1102w Printer not showing on your Macintosh computer. I may have found some resources for you.
I have a few questions for you, so I can offer some additional assistance:Before you upgraded to the Apple AirPort Time Capsule, was the printer working wirelessly without any issues?
When you say; 'I reset the printer to factory settings', how where you trying to do this?
I found some instructions from this post: How do I reset my Laserjet p1102w to its defaults, copied here for you:
To restore the printer back to factory settings, turn the printer off, hold down the wireless button and the cancel button (x button) then turn the printer back on and don't release the two buttons until the printer stops making noise. (When they say turn the printer off, I think they mean unplug the power cable.)
"I've checked to make sure both computer and printer are on the same network." Do you know if you are able to access the printers Embedded Web Server (EWS)?To access the EWS - Make sure that the Ready light () is on and that the printer is idle and silent.Press and hold the Cancel button (), and release it when the Ready light () begins blinking.The configuration page prints.Type the IP address or host name of the product in the address field of a supported Web browser, and then press Enter on your keyboardLet me know if this page loads
To answer a few more items you have listed:... When I go to the printers window in my system preferences, there is no wireless printer available to add in the "available printers" menu.This could be an issue with your print system, I recommend resetting the printing system and then Repair Disk Permissions - after that try to add the printer again.
... the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download)HP provides their software/drivers to Apple to be released through your Apple software updates. You can review this document on how to Install a Mac Printer Driver Using Apple Software Update. Which leads into your next point...
... there is no installation software that pops upWhen you connect the USB cable your mac may still recognize the printer software as being already installed - check for apple updatesOn the Mac, click the Apple menu (), and then click Software Update, or click About this Mac, and then click Software Update. A list of available updates displays.
... Not seeing the printer in "Finder" From what I understand most printers will not show in Finder unless you install a memory card into a supported port on certain printer models, only then will it read it like an external device. A few more things you can check are that the new settings in the Apple AirPort Time Capsule are setup to allow the printer to communicate. There are several of these settings listed in this document; Tips and Workarounds for Common Wireless Network Printer Issues. HP regularly releases firmware updates that may also correct the problem you are experiencing. You can click on this link to Getting Printer Updates for HP LaserJet Pro P1102w Printer. I did find 2 more documents that may offer some additional information as well;HP LaserJet Pro P1102w Printer - Connecting the Printer After Changing Your Wireless NetworkAn 'Unable to Find Printer' Error Displays for the HP LaserJet Pro P1102w Printer Please let me know if any of these steps resolved your issue, or the details of what happened. I look forward to hearing from you, hopefully with good news! Thanks,

Can't establish ftp connection between a Xserve and a PB

We want to use a Xserve (Mac OS X Server 10.4.8) to provide webhosting, but experience problems in establishing ftp connections using a PowerBook (Mac OS X 10.4.8).
On a WinXP-based notebook using the same Internet connection, anything works fine, just not on my PowerBook.
This is what happens when trying to establish a ftp connection (via terminal):
I type: ftp [email protected]
Returns:
220 star1.local FTP server ready.
331 Password required for user.
I provide the password, anything looks fine, get this output:
230 User starenterprise logged in.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp>
Okay, now I want to see what files are in the directory using "dir" command ("ls" brings same result). This output is shown:
502 'EPSV': command not understood.
227 Entering Passive Mode (132,78,123,92,42,115)
Now I can either press CTRL+C to escape or when waiting around one minute, then it states this:
421 Service not available, remote server timed out. Connection closed
On a ftp client software like CuteFTP Mac it shows "Can't open data connection" instead of, but result is the same.
I read through some articles I found here, but nothing compared to my problem. Please help.
I should mention one thing Apple's support told me: Since I have the same username and UID on my PowerBook as well as on the xServe, it could bring problems. However I have then added a new user to my PowerBook, result is the same. And Apple's support left helpless so far.

You said: "Not really answered, the problem persists and I now go on and let
Apple work on it again"
As a native English speaker, I must say (and doubt any would disagree) that
your statement implied: "No one here has actually helped me fix this problem,
and now I'm waiting for Apple to fix it"
Please take care to the word "again" I used; this implies that Apple has tried to solve the issue before but failed (in fact, they stated to call me back, but this is weeks ago) and so I posted this here at the discussions.
Unfortunately I only have access to the "free" support (well, free is not the right word when paying 12 cents per minute for the phone call).
And this means (at least I can speak for the German part of Apple) that operators on the phone look at their knowledgebase and sending articles by e-mail; questions going deeper are resulting in a "we call you back" answer. Sometimes they phone back, sometimes not. Sometimes they are helpful, sometimes (or should I say "in most cases") they just give hints or ask me to investing a nice amount into premium support.
Don't misunderstand me in the direction that I demand assistance from this forum - I'm more than gradeful if I get help (and rewarded this always with giving points), it has saved me several times (many, many, many times) for doing time consuming investigations and making trial-and-error experiences by myself. If I cannot get more assistance, well I have to look elsewhere and so be a bit impertinent to Apple's support. Perhaps it helps
You are right, FTP itself works correctly. It even works fine on the WinXP notebook residing at the same LAN as my PB. Therefore the issue is at the PB's firewall very likely (or a strange relationship between two firewalls which seems not to affect WinXP).
But as you indicate, it makes no sense to lower down security just for doing ftp, especially since SSH works well. However since I have no problems doing ftp sessions with other servers, I would be eager to find the reason why it refuses in this case, even this just means feeding my curiosity
So if I come to new insights, I post them here. But I feel that I'll really need your wishes for luck to solve this problem Let's see...

APO/BW: Verifying/Establishing a connection between BW and APO

Hi
1. Is there a way to see that my BW system is connected to an APO system, other than finding a name with APO in it under the Source System tree in BW?
2. Also, if the connection does NOT exist between BW and APO, can you provide me with the steps on how do I establish such a connection?
3. Does a successful in Generate Export DataSource in BW indicate that my BW system is connected to APO DP?
Thanks

. Is there a way to see that my BW system is connected to an APO system, other than finding a name with APO in it under the Source System tree in BW?
In source system tree, you will find all the systems that are connected to your BW system. The system name need not have to start with APO.
2. Also, if the connection does NOT exist between BW and APO, can you provide me with the steps on how do I establish such a connection?
Transaction Sm59. you need to know the source and destination IP adresses. Usually, the baais will take care of connections.
3. Does a successful in Generate Export DataSource in BW indicate that my BW system is connected to APO DP?
NO. Export generaion is within BW system; nothing to do with the APO system that is connected.
Ravi Thothadri

"Unable to establish a connection between WebEx and the mail server."

Hi,
I installed Cisco WebEx and integrated with our Microsoft exchange server. It showed server "UP". everything's came up and working fine after that and sudenlly i found this message "Unable to establish a connection with the mail server. Please recheck settings."
I went into the Mail Server setup to edit settings and now, it shows Server Down. Do I need to do something on the MS Exchange 2010 or from webex server ??
Any help is greatly appreciated. Thanks a lot!

Every 180 seconds, CWMS verifies the connection to the SMTP server by establishing a connection on TCP port 25 (SMTP) and then sending the EHLO command followed by the QUIT command. This check is also performed once when logging into the admin web page or when browsing to System -> Servers (where the status of the mail server is displayed).
If this sequence does not complete successfully, the warning “Unable to establish a connection with the mail server. Please recheck settings.” will show in a banner at the top of the CWMS admin pages.
You can verify the connection to the SMTP server manually by using “telnet 25”.
If you have access to the CWMS unix shell be aware that CWMS does not come with the telnet command installed.
As an alternative, you can use this 3-lines script:
exec 3<>/dev/tcp/x.x.x.x/25
echo -e "EHLO\r\nQUIT\r\n " >&3
cat <&3
Replace x.x.x.x by the ip address or hostname of the SMTP server and save the script in a file, f.e.:
/* script saved in a file named ehlo */
[root@dchriste-cwms-adm1 ~]# cat ./ehlo
exec 3<>/dev/tcp/10.48.54.79/25
echo -e "EHLO\r\nQUIT\r\n " >&3
cat <&3
Then, execute it:
[root@dchriste-cwms-adm1 ~]# sh ./ehlo
The output should be similar to this:
220 *******************************************************************************************************************
250-confukdc.confuk.com Hello [10.48.52.110]
250-TURN
250-SIZE
250-ETRN
250-PIPELINING
250-DSN
250-ENHANCEDSTATUSCODES
250-8bitmime
250-BINARYMIME
250-CHUNKING
250-VRFY
250-XXXXXXXXXXXXXXXXXXXXXXXA
250-X-EXPS=LOGIN
250-AUTH GSSAPI NTLM LOGIN
250-AUTH=LOGIN
250-X-LINK2STATE
250-XEXCH50
250 OK221 2.0.0 confukdc.confuk.com Service closing transmission channel
Also, you can use this tcpdump command to see the conversation (replace x.x.x.x by the SMTP server’s IP address or hostname):
tcpdump -vXs 0 host x.x.x.x and tcp port 25
If you have HA, it is not certain which admin VM talks to the smtp server, so best to check both.
If you don't have access to the CWMS unix shell, best to span the switch ports and run packet capture.

Cable connection between 6280 and MacBook

Hello,
I'm using Mac OS X 10.4.9 and I've also got an Nokia 6280.
As other users before, I've already tried to use the cable that came with the mobile, but it's not possible to copy files on the miniSD card.
On http://europe.nokia.com/A4299040 my phone is listed and Nokia claims that it could be connected via bluetooth and USB, but USB doesn't work. :-(
Can anybody help me? With the help of bluetooth it's often very difficult to sync new photos.
I hope you can help me and: Please Nokia, improve the integration of the 6280!
Thanks!

I have an update on this subject.
Nokia told me that it is Apples responsibility to provide a USB diver :-(
In the apple support forum I found the information that it worked with the Tiger OS.
http://discussions.apple.com/thread.jspa?messageID=6191872#6191872
Here in the forum I found some infos how to use the old Tiger USB driver with the Leopard os.
/discussions/board/message?board.id=pcsuite&message.id=20885
My only problem at the moment is; where to get the old Tiger driver from???
If I get more I will keep this place up-to-date.
c.u.
Alrun

Cannot establish Bluetooth connection between iphone4 and ipad2

I have an iphone4 which cannot connect via Bluetoooth with ipad2, even though I tried all that is said in Apple support , but still no success. Really cannot understand as my iphone4 connects to a Bluetooth ear piece which is of different make and these 2 piece's are from Apple but cannot establish a connection via Bluetooth. It's surprising. So please help and advice.
thanks Guys

The iPhone is not designed to Bluetooth pair with a computer or an iPad except for personal hotspot (sharing the phone's cellular internet connection). It can use Bluetooth for Handoff/Continuity and for Keynote Remote but the devices are not paired. More information: Bluetooth: Why can't I pair my iPhone or iPad with my computer?

Can't establish infrared connection with 6101 and ...

As I've recently upgraded my phone I want to store my pictures from the 6101 I am replacing. Eventually, PCSuite will complete the connection setup, but when I go to Store Images and click Select Phone it either doens't list the phone or, if it does, I select it but the ok is not activated so can't proceed - evenutally the phone disappears from the list and I start over... I've also tried copying files and backing up, but the connection always goes. Please help! I've been trying to do this for days! Really don't want to lose my images (pic's of kids, you know).
Thanks.
Berta

Have you tried the file manager in PC Suite ?
Connect the phone and see it the phone is visible in File Manager ? When you can browse to the right folder (Gallery - Images or memory card depending where you have the images and manuallly move them to PC folder ?

How to get picture on tv after hdmi cable installed between mini and tv.

I HAVE CONNECTED MY MAC MINI TO A TV MONITOR WITH AN HDMI CABLE. I HAVE SELECTED HDMI INPUT ON TV. NO PICTURE ON TV, WHAT DO I DO?

Try a different HDMI cable and restart the Mac Mini.
Also if this is a new Mac Mini, you have 90 days free Apple phone support.
Apple - Support - Product Selection

Cable connection between card and dri

Looking for a round cable to replace flat cable that connects sound card to dri've! I know they make round cables for other dri'ves to dress up tower looks and air flow but does anyone make one for the Creative dri've and card connection?

Creative Labs XFi/Audigy Cable Sleeving Service

Can't establish Fiber link between 7609 and 4006

Our Service Provider runs a 7609 and has Q in Q tunneling to provide us L2 vlan services over a MM Fiber link.
We have a 4006 on 12.2.25 (EWA9) with a 6 port Gig blade WS-X4306-GB and are trying to establish connectivity on the link, but the conenction remains in down/down state, regardless of the configuration changes we have tried (speed nonegoiate, flowcontrol send/receive on/off, switchport mode trunk/desirable/auto).
Oddly, the same Gbic and fiber feed, connected into a Cisco 3550 switch comes up with no problem.
Below are the configurations of the Service Providers 7609, as well as the configuration of the 3550 (which worked), and the configuration we tried on the 4006.
Please review and advise of any problem you see in the configurations.
Thanks,
-Scott
Customer Cisco 3550 Gi0/2 (Worked to 7609):
interface GigabitEthernet0/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 750,760
switchport mode trunk
speed nonegotiate
Customer Cisco 4506 Gi3/2 (didn't work to 7609):
interface GigabitEthernet3/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 750,760
switchport mode trunk
speed nonegotiate
Service Providers Cisco 7609:
interface GigabitEthernet3/3
mtu 1546
no ip address
speed nonegotiate
wrr-queue bandwidth 70 30
switchport
switchport access vlan 499
switchport mode dot1q-tunnel
switchport nonegotiate
l2protocol-tunnel shutdown-threshold cdp 200
l2protocol-tunnel shutdown-threshold stp 200
l2protocol-tunnel shutdown-threshold vtp 200
l2protocol-tunnel cdp
l2protocol-tunnel stp
l2protocol-tunnel vtp
no cdp enable
spanning-tree bpdufilter enable
service-policy input 500mb

We finally found the problem. Because the LEC put a MUX in the fiber path, we had to add the interface command "pos scramble-atm" to both our router and the ISP's end.
Once both ends made this change, the circuit came up.

My Macbook Air failed the cable connection between Monitor and Mainboard

When I just got accident with this macbook air version 2008, It still working but after one week the screen got the blue color but The Mac OS still working. Now I want to contact with the technician of Apple to help me get the price and solution for my Macbook Air but I don't have the email, Please help me to fix it.

I have an update on this subject.
Nokia told me that it is Apples responsibility to provide a USB diver :-(
In the apple support forum I found the information that it worked with the Tiger OS.
http://discussions.apple.com/thread.jspa?messageID=6191872#6191872
Here in the forum I found some infos how to use the old Tiger USB driver with the Leopard os.
/discussions/board/message?board.id=pcsuite&message.id=20885
My only problem at the moment is; where to get the old Tiger driver from???
If I get more I will keep this place up-to-date.
c.u.
Alrun

Connection between PDA and desktop can not be established

I recently got the Palm T/X. I was able to upload the programs I needed, but now I can not establish a connection between the PDA and the computer. I even bought another USB hotsync cable thinking my original cable was faulty. Still no luck. I have noticed that the cable itself seems easy to plug into the PDA but I have to physically struggle to disconnect it from the PDA. Any idea what the problem could be? Thanks for any help.
Post relates to: Palm TX

The hotsync manager icon is there but it will not open. Tried to open it manually without success. I did get to the Palm InstallShield which said it would have to erase everything on the PDA to reconfigure the hotsync setup. Not willing to take that risk as I have some expensive medical software on there now. I have tried all 3 USB ports on my computer. Any other suggestions will be much appreciated. I simply want to HotSync!
Post relates to: Palm TX

Connection between Portal and MDM

Hi all
Can anybody help me on how to establish the connection between portal and MDM with step by step procedure.
i am new to this combination .
before i worked with portal but not worked with MDM .
Regards
Suresh babu

Hello Suresh,
As of my knowledge MDM IViews have the advantage to ful fil your neeed to provide connectivity moreover,that they are not complex in structure and are therefore not restricted by any underlying schema structure. As opposed to regular iViews in other systems which are embedded into the pages on which they appear, MDM iViews are more generic and granular in nature enabling their placement on a page to be more adaptable.
The SAP Enterprise Portal (SAP EP) offers templates for creating the iViews. The following are some examples of these templates available at the link:
[http://help.sap.com/saphelp_mdm550/helpdata/en/45/c9f8cac2124ebee10000000a11466f/content.htm]
Procedure:
       1.      Create a new page using the page wizard.
       2.      To see the iViews you created on the new page, you need to link them to the page. Right-click each of the iViews that you created and from the context menu, select Add iView to Page → Delta Link
       3.      Double-click the new page you created and select:
Page Content to view a list of the iViews that have been linked to this page
Page Layout to view the layout currently assigned to this page. The iViews can be rearranged using the drag&drop function.
       4.      The visual structure of a page can be changed with the Page Layout function. Select Define Layout to reset the layout of the page.
       5.      Select Preview to view the page showing how the iViews have been arranged. The preview simulates what an end user sees at runtime.
Detailed pictorial presentation available at:
[http://help.sap.com/saphelp_mdm550/helpdata/en/45/c8e2fa5f0c2e97e10000000a155369/content.htm]
Hope you will find it helpful.
Regards,
Krutarth

Can't establish cable connection between mini and TC

Similar Messages

Maybe you are looking for