Capturing DVCAM tape

I am capturing a DVCAM tape via Firewire from a Sony DSR-11. In the Log and Capture window I select the DV NTSC 48 kHz capture preset.
However, the resulting video looks bad. It's heavily pixilated and not sharp, not at all how it looked in the preview window and when viewed on an external broadcast monitor.
Any suggestions?

That is how it looks. It is just a "proxie" image for you to see what is being captured without needing an external monitor attached. It will look like crud. But, as you said, that isn't how your footage REALLY looks. For that, just look at the external monitor that you should have attached to the deck if you want to see a good quality image.
Shane

Similar Messages

  • Capturing DVCAM in FCP 6.0.2 and encountering strange capture behavior

    I have FCP 6.0.2 and OSX 10.5.2 and QT 7.3.1. I have been capturing several DVCAM cassettes using my Sony DSR-20 deck. Although I have done this countless times before in earlier versions of FCP, I am encountering some strange repetitive behavior. I am capturing 30 minute clips one at a time. When I use batch capture it will cue the tape up properly to the in point...and then start capturing until it gets to about 10-12 minutes in, and then capture unexpectedly stops, no dialogue box, the tape rewinds and starts capturing again from the original in point. On this second capture, the tape sails past the 10 minute mark and keeps going to the end of the 30 minute clip. It then stops, gives me the dialogue box that it has successfully captured. And it has.
    But every DVCAM tape I captured today exhibited the same behavior. Capture would be successful until about about 10 minutes in, then FCP aborts (no dropped frame message, no dialogue box) rewinds the tape back to the in point, tries again, and this time succeeds with the second pass capturing the entire clip. Note at the 10 minute mark there is no scene change or no camera start/stop.
    Have other users experienced this issue? And if so, is there a workaround or a possible patch forthcoming from FCP?
    Many thanks,
    John

    Yes, each tape has an in and out point defined. In my 6 years of editing with Final Cut and DVCAM tapes I've never encountered this issue before in the capturing process until now. I will have to see in future weeks with other captures whether this is an on-going issue or not, but at least I can capture for now.

  • DVCAM tapes

    So I've been asked by my church to create a DVD of a Dance Festival that will be digitally recorded by a professional service, they will be recording on DVCAM tapes, the larger ones.
    I have found that a DVCAM player costs around 7000 dollars.
    Any recommendations on how I can capture this video? Are there resources that would allow me to rent equipment of this nature or perhaps go to a studio and utilize some equipment?
    Has anyone here had experience using DVCAM?
    Thanks

    You can usually find a rental house that offers DVCam VTRs. Or you could pay the same people that are taping the event to capture the material to a FW hard drive that you provide. Or check with production/post-production companies in your area to see if they can do it for you.
    Or you could look for a used DVCam VTR. A used Sony DSR-11 will often sell for around $1000.00 on eBay.
    -DH

  • DVCAM tapes to FCE setup required

    I need to transfer DV footage from 4 DVCAM tapes onto my G5 for editing in FCE. I'm waiting to receive my copy of FCE HD and I have located a place where I can rent a Sony DSR-11 DVCAM deck. But I am totally unsure on how to connect the DSR-11 to my G5. The DSR-11 shows (I look at brochures) a DV IN/OUT which uses a 4pin iLink DV in-out cable which appears different from the firewire connections in th G5, even if the sales rep at the rental outfit told me there is Firewire out on the deck. Can it be connected directly to my Mac using a Firewire 800 cable or do I need a capture card with the DV IN?. Will Final Cut Express see the DSR as a camcorder/deck? Incidentally I also just received a Director's Cut Take 2 Media box which I could use with the S-Video inputs and DSR S-Video outputs, but it would mean a double conversion, wouldn't it?
    Any insight greatly appreciated before I commit money to the rental of the deck. Thank you

    You need a four-pin to six-pin FireWire cable. Use the rear FW 400 port on the computer. Yes, FCE will see it. Make sure the deck and FEC are set to work in PAL.

  • Capturing DV tapes to large drive

    I have over 100 DV tapes that have never been archived or logged in any way. I have two 1TB drives and would like to capture each of the tapes separately in such a way that in the future I can use FCP 6 (on an Intel Mac pro) to edit these tapes. I will be using my camera as the video input device and would like to put a tape in and "walk away" while FCP captures the tape in real time. My thought is that once a tape is captured the digital computer file is much quicker to navigate than using the camera as a video playback unit. I realize that 2TB will only go so far. I would like each tape to have a corresponding computer file.
    My question is what is the best way to capture these tapes so each tape has a corresponding file that will be usable by FCP when the time comes to edit them into different projects? Is it as simple as doing a "log and capture" for each tape giving each a unique reel number?

    Well, I'm obviously in over my head, but I unfortunately find myself with quite a bit of time in the next couple of months to try and pull this off.
    As mentioned above I would like to capture many DV tapes. At this point I do not want to do any editing. I want to capture them in a way that does not limit me in the future when I try to create and edit numerous projects. I have a large dedicated drive. What is the best way to accomplish this:
    What should the folder structure look like at the "Finder" level?
    Should each tape be a separate project?
    I do not know what is on these tapes and I would like not to preview them before they are captured. Is it possible to change the "Name" or add a description after the tape is captured (since during the capture process I will have a better idea what is on it)?
    What is the best way to capture these tapes allowing for the greatest flexibility in the future. I'd like to avoid spending two months doing it the wrong way.
    Thanks for the "leading zeros tip"
    Thank you all for your help.

  • How much loss in capturing from tape?

    Looks like the days of tape are numbered.  If they haven't already, everyone will be using tapeless formats before too long.  I have a large library of HD (miniDV format) tape.  When clients want raw footage, I copy tape-to-tape using two camcorders and send a copy of the raw footage.  That will soon be impossible, because no one will be able to play the tapes. What's left is to use CS4 to capture the tape footage directly to a hard drive or memory stick and send that. I have no idea how much loss of data there is doing that, and hope someone might have some numbers to share.
    Thanks.

    A Firewire transfer from tape to computer is a copy operation... so there is no loss of quality
    Of course, those files are "about" 13Gig per hour for DV (I don't know the size for HDV) so sending a file to someone is going to mean several DVD's to write the files, in 4Gig segments, or copying to a USB hard drive and sending that back and forth

  • Batch capturing entire tape...recomended???

    Is it a good idea to attempt to batch capture a tape in its entirety? I am having problems doing this...I do a lot of events that last often over 2 hours. Instead of capturing footage in clips, I just capture the entire tape. When I'm done with the project, I simply make the clips offline.
    I'm in the process of reviving a project now, and one tape in it's entirety(55 min approx), captured OK, but I am having problems with another tape. I am getting a broken timecode error, when I don't see how this is possible...because I let the tape freely run. Also, under the logging info, the media ends before the tape ends, which means that is space left on the end of the tape without any timecode. Yet when I batch capture, it still goes to the end of the tape.....isn't a batch capture suppose to go by the clips media in and media out points?
    All help is greatly appreciated.

    I do this often. There are two shools of thought on this method -
    Capturing entire tapes allows one to scroll through non-linearly and make subclips. The advantage to subclips is that they are serachable and you can add comments. The downside to this method is that the files are large, and you may be capturing much more metarila than you need. I often do this when working on docs with very high shooting ratios. The most recent one had 190 tapes for a 1-hour program, which led us to use offline RT for our cutting format and then recapture for online.
    Logging and capturing single clips fives you the advantage of starting out capturing only what you know you might use, you can input the logging info at the start, and will have several small clips that may be easier to manage. Since at some point you'll have to familiarize youself with the matreial anyway, you might as well do it at the logging stage.
    Several factors can contribute to perceived TC breaks - reusing tapes, camera stops, shooting format (HDV, for instance, will show a TC break each time the camera stops). If you are capturing whole tapes, you might do well to let FCP create new clips on TC breaks and just let it roll. Make sure the TC format matches between your tape and settings (DF vs. NDF)
    Regarding rolling off the end of the tape during capture, you might be very close to the end with the clip you are capturing. You might try lowering the post-roll value in the device control preset in your A/V settings.
    Hope this helps -
    Max Average

  • 8mm and Canopus or Digital 8 for capturing 8mm tapes?

    I have a Canopus 300 that I've been using for capturing VHS tapes. I also have an 8mm camcorder. Will that camcorder + Canopus do as good a job as a Digital 8 camcorder or Digital 8 playback deck?
    Thanks!
    MikeR

    Probably only a side-by-side comparison using the same test footage would provide a definitive answer as to which path produced the better result.
    The data stream on a Digital8 tape is the same DV stream that is on a miniDV tape. The data is identical, it's just the physical tape that is different. You can only get 1 hour of DV onto a 2-hour Hi-8 tape, because the Digital8 camcorder runs the tape at approximately twice the speed.
    My Sony DCR-TRV460 is smart enough to recognize the signal and switch between modes. I even have a few tapes which have regular analog 8mm video on part of the tape and Digital8 on a later part of the same tape. When it reaches one of these changes, the camera automatically stops and switches mode, then starts rolling again.
    Not all DV is exactly identical, I have found out. There is a small discrepancy between the way Panasonic cameras record DV and the way Sony cameras record DV. I found this out when a colleague sent me a miniDV tape recorded on a Panasonic camera. I took it to a video shop to have it copied over to a Digital8 tape, which should have been a direct digital copy. But at the shop they told me Panasonic records DV in a slightly different way. The result is that there were some glitches and artifacts on the copy, and some audio problems as well. If you stick with all one manufacturer you should probably not run into that problem.
    The downside is that I have found Sony camcorders to suddenly fail to operate at the worst possible moments, and for no apparent reason. This has happened to me several times, in fact my TRV460 died a couple of weeks ago. It is always wise to have an expert repairman who is knowlegeable about Sony available at all times.
    I think that the Sony deck (GV-D200) might be exactly what you need for your project, but at $500 for a new one (or maybe $250-$300 for a used one on eBay) that would be a significant cost.
    Message was edited by: Bob Weaver

  • Export HD 720p to DVCAM tape (print to tape) 16:9 not letterboxed

    hi -
    i'm trying to export an HD 720p24.00 project to DVCAM tape for projection at a film festival. i need to make sure the 16:9 aspect ratio is squished, not letterboxed, onto the DVCAM tape. what is the best way to go about doing all this? i am exporting to a DSR-11 DVCAM deck.
    thanks in advance.

    follow up:
    actually, if the DV sequence is 24.00 fps, it won't play in an external monitor through my deck, nor will it print to video.
    so now i'm trying to put the HD 720p sequence into a DV 23.98 sequence and render and we'll see if that works better.

  • Will idvd with a new MacBook Pro work with a DVCAM deck? I'm using firewire to burn a DVD from a DVCAM tape in a Sony DSR-30 deck but it isn't working.

    Will iDVD with a new MacBook Pro work with a DVCAM deck? I'm using firewire to burn a DVD from a DVCAM tape in a Sony DSR-30 deck but it isn't working.

    http://www.lafcpug.org/phorum/read.php?1,268296,268300
    Bit of googling wouldn't go astray.

  • How to export a clip to a DVCam tape via a recorder

    I am unable to transfer a clip to a DVCam tape because there no such alternative in the menu share of FCP X. Can some one advise on how to proceed. The right question is HOW TO PRINT TO VIDEO IN FCP X ?

    FCPX doesn't do this.
    You will need a third party hardware and software.
    Here's an example.
    Good luck.
    Russ

  • True 24fps Film Project out to DVCam Tape - Proper Settings?

    I have a TRUE 24fps 1080x1920 Uncompressed Quicktime of my film.  I'm  going to be using Premiere Pro CS5 connected via Firewire to a Sony  HVR-Z1U Camcorder, which is capable of DVCAM recording and playback.  I  need to record the film to DVCAM tape for a film festival....and I was wondering 2 things:
    1.  What framerate is needed for DVCam?  I'm guessing I will need to convert the film to 23.976 before outputing it to tape....
    2.  If I need to convert to a 23.976 file beforehand....what is the best  quality file for output to DVCam?  The best way I know of currently to  convert my true 24p footage to 23.976 is by going into After Effects and  converting to MPEG2...setting the M-Frame to 3 and the N-Frame to 12 so  I avoid conversion flicker problems....but I know MPEG2 will probably  be pretty lossy compared to other file formats that DVCam tapes can  handle.
    Any help would be much appreciated!
    Thanks,
    Doron Kipper

    DV and DVCAM are effectively the same, 720 x 480 NTSC or 720 x 576 PAL and the framerate is 60i or 50i. Assuming NTSC you need to rewrap to 60i using MS DV AVI.

  • How to export to DVCAM tape with timecode from Premiere CS 6?

    I am having a lot of trouble with this. I need to give a dvcam tape with proper timecode to a television station for a Show I edit. I am editing for this station for last 7 years. Before they accepeted betacam, but now they changed to DVCAM. I have Premiere Pro 6 (or CC) and SONY HVR M15U deck. I connected it via firewire, then realized firewire can't export timecode. Now I am in a pickle.
    Possible solutions (may be):
    - Buy a card, send other signal like SDI to the deck?
    - Buy new deck?
    Please help. I able to print to tape via firewire, but how can I print the timecode?
    Thanks
    Raman

    realized firewire can't export timecode.
    Sure it can.

  • Print hdv sequence to dvcam tape

    I've never tried it, but can you print a hdv sequnce to a dvcam tape?
    I've had a look at the forum and a few people mention using compressor, but I have fce 4 which hasn't got compressor.
    Does anyone have any experince doing this in fce 4?
    Thanks.

    Do you have a DVCAM camera or deck? Do not do this with copy and paste. Take your edited HD sequence and place it inside a DV anamorphic sequence to scale it properly and correct the pixel aspect ratio. Before you do that make the the HD sequence is fully rendered and mixed down. Then once inside the DV anamorphic sequence, render and mix down that, then print to video.

  • Weird thing happens when capturing from tape...

    So I'm using Adobe Premiere Pro CS6 and I'm capturing from tapes. I either set in and out points or capture the whole tape when I do this. When I start capturing, what would sometimes happen is Premiere would stop capturing the footage in the middle, but there's no kind of error at all. What it seems to me is that Premiere would think that my out point is earlier than what I said it was so it would capture only part of the footage I wanted into my bins, but then I can just move the in point to where it left off and it would capture the rest of it (though it may stop several times). The captured files don't seem to be corrupt either. Does this make sense to anyone? I'm just wondering if it's the program itself, the tapes, or something else?

    please guys can you guys just try it out for me and tell me if it happens to you too. i've already heard from an x200 user that this happens to him as well. it would be better to hear from more of you guys.

Maybe you are looking for