Capturing DVCPro50 24P Footage

If anyone could help, I would appreciate it. I am trying to capture Anamorphic DVCPro50 footage shot at 24 fps (Panasonic DVCPRO50 Deck). I initially captured the footage with the following captured the footage DV50 48KHz Anamorphic. The footage looks great on the timeline (DV50 48KHz Anamorphic), but it is sped-up. I made a new timeline (DV%) 48kHz - 23.98 Anamorphic)and the footage moves at the correct speed, but I have to render the footage. Is there any capture setting that coincides with this timeline setting? Or is the deck playing the footage at the wrong speed? Where have I gone wrong?
Please advise.
Thank you.
Message was edited by: Brian Hunt1

Did you shoot 24p or 24pA?
At either rate, you captured as 29.97 with that preset. Which is why you must render it on a 23.98 timeline.
I'm not sure why it's speeding up the footage, are you positive that is happening?
If you shot 24pA and want to work on a 23.98 sequence, recapture using the DVCPro50 Anamorphic Advanced Pulldown Removal preset.
If you shot 24p, work on your 29.97 timeline with the footage you have already captured, and make sure it is really speeding up.

Similar Messages

  • Best DV deck for capturing Panasonic 24p footage

    Hi everyone,
    I'm working with 24p footage from Panasonic DVX-100A and HVX-200 cameras. I've always found the tapes tricky to capture with Advanced Pulldown Removal, and now I'm unhappy with my Sony DSR-11 VTR.
    I'm finding that some equipment plays nicer with 24p footage than others.
    Some of my editing colleagues have suggested that I should use Panasonic equipment - and they do have an equivalent low-end DV deck, the AG-DV2500.
    Any suggestions from the field? My budget does not permit buying a full-blown studio DVCam machine, unfortunately.
    Joe

    I put this question to Larry Jordan, of newsletter fame, and he feels that I'll be better off with a Panasonic VTR - so I'm gonna give that a try.

  • How to capture HDV 24P footage without pull down

    I´ve got some imagens with HVR-V1U in a HDV 24p mode thinking to transfer to film. Now I´d like to uploud the images in the same mode. In Premiere there is only HDV 30p and the option 24p only works for dv format. So, in the HDV 30p I receive the file in a Adobe with 6 more frames per second and it doesn´t work for cinema. Is there any way to edit a project in Premire in HDV 24p mode, and in this case how to get the file from the camera.
    thanks.

    Hi(Bonjour)!
    Final Cut Express doesn't support HDV natively. It uses Apple Intermediate Codec upon capturing process to convert the HDV format.
    Even if you can download your HDV from your PC to your Mac, you haven't the HDV native quicktime component to open the material for conversion to AIC purpose.
    Final Cut Pro allows to works with native HDV.
    So why don't you use more tapes and keep archived source material. Mini DV are pretty cheap these days.
    Michel Boissonneault

  • JVC SD 24p footage capture settings

    So I've been working on a short for the past few months, and just when I thought it was all ready to go, I exported for DVD and discovered that something was wrong with the footage -- somehow, in the capturing process, we dropped a frame and every 5th frame was duplicated. I am now trying to recapture the footage properly, but find that no matter what settings I tweak, the end result is the same. Can someone please tell me the proper capturing settings for footage shot in SD 24p with a JVC GY-HD camera? I do know that this is a stupid question, but hopefully that means someone will have a quick and useful answer -- which will be SO MUCH APPRECIATED. Many thanks!

    I think I'd just capture useing the easy setup for DV NTSC, and use "firewire Basic" as a device control setting for that camera.
    24p is recorded at 29.97 with a pulldown added, and you needn't remove this pulldown for any real gain with short programs.
    Jerry

  • Capturing 1080p 24p from p2

    I have received a drive with footage that was shot on the Panasonic HVX200 with P2 cards. After speaking with the DP, the format of the footage is DVCPro HD 1080p 24p (not 24pa). After performing the Log and Transfer, when I look at the clip I see 3 progressive frames, then 1 interlaced frame (repeats).
    Page 66 of the manual for working with FCP & HD video indicates
    To remove standard 3:2 (2:3:2:3) pulldown from 1080p24 footage, you need to
    capture the footage as 1080i60 (29.97 fps) and then use Cinema Tools to remove
    the pulldown.
    Page 100 indicates:
    The Import Panasonic P2 window cannot remove standard 3:2 pulldown.
    To convert footage with 3:2 pulldown, you can ingest the media at 29.97 fps and
    then use Cinema Tools to remove the pulldown.
    Page 103 indicates:
    Use Remove Advanced Pulldown command in Final Cut Pro or Cinema Tools after capture or ingest.
    I am familiar with Cinema Tools, and have performed the conform process before with footage from the HVX100 in Standard Definition with no problem. However, when I attempted to remove the pulldown in cinema tools, the footage appears unaffected even though the frame rate is now 23.98.
    I read in another manual "Workflow for Final Cut Pro and the Panasonic AG-HVX200"
    that 1080p 24 is Not supported at this time.
    Has anyone had success capturing 1080p 24p from a p2 card and then removing the pulldown to get 23.98 with progressive frames?

    Just to make sure, since you mentioned advanced pulldown. You should be removing regular pulldown, not advanced pulldown. Also, conform is for files that are already progressive. What you want is reverse telecine. Try doing a batch reverse telecine on a few clips. I've had problems in the distant past doing it on single clips because I wasn't starting with an A frame.

  • Film workflow with 24p footage: nightmare

    Hoping someone can give advice on a disaster i'm experience as I cut a film I'm working on, the sequel to this-
    http://www.youtube.com/watch?v=GpuEMSH6zB4
    I shot the film in straight-up 24p. When capturing the footage at 24p, we experience a quality loss. At 29.97, there is no quality loss. This makes no sense.
    Also, when I get my 24p footage, captured at 29.97, into a 29.97 timeline, and then resder it out at 29.97, there is a quality loss.
    Also, my ability to have moving video not only in the FCP viewer window, but also through the camera out to a TV, comes and goes. It will freeze or unfreeze depending on some thing having to do i think with the framerate of either the clip or the sequence.
    It's blowing my mind. I did not experience this problem on the last flick, and I shot it the same way. Is my FCP damaged? Is there a tutorial out there to guide through this problem, or have any of you experienced it?
    Any info would be greatly appreciated.

    24P runs at 29.97. 24PA is what you shoot if you want to work at 23.98. If you shot 24P, then you work at 29.97.
    You capture as normal 29.97 DV footage, edit at 29.97, output at 29.97. You use no pulldown.
    Shane

  • Importing HV20 24P footage

    I imported 12 hours of 24P footage from the HV20 into Final Cut using the HDV 108024P preset before reading the instructions of how to make it "true 24P" that say that the footage needs to be imported as "HDV108060i".
    Do I need to reimport all that footage to do the steps needed to make it real 24P?
    Also, if I did not change it to real 24P and added it to a timeline that was 24P with A1 footage would the two look the same or would the HV20 footage have some issues?

    Hello,
    When you say imported, do you mean imported from a file, or captured from the tape?
    When you say 24p footage, have you already done the reverse telecine process on it?
    The camera shoots 24p, but stores it as 60i on the tape. When you capture, you end up with 60i data, with duplicate frames on a cadence (you can check this just by stepping through your video frame by frame and watch for duplicates)
    You can take captured 24p video (which is contained in a 60i format) then use compressor to remove the extra frames. Then you can then place that clip in a 24p sequence and edit as you wish.
    I would guess that when you say you "imported" 24p, you mean that you captured the HDV from the hv20 something you shot in 24p mode. FCP would have captured it as 60i video, so you probably don't need to re-capture it. Just place the entire capture onto a sequence, accept the format of the input, then send it to compressor to change (reverse telecine, aka removing the extra frames) the 60i sequence into a true 24p sequence. then you use this true 24p material in a new sequence that you can then trim and edit.
    Ken

  • Using 24p footage and 60i footage together?

    Hello,
    I am working on a project that will combine 24p footage and 60i footage. What would be the best way to go about combining these two. It's for a short that is shot similar to Cloverfield. I want to use 60i footage for the hand held footage shoot by the actors who are capturing their experience. I'd prefer to have that footage shot on 24p as well and degrade the quality in post, but I don't want to run the risk of them dropping my DVX100a and destroying it. I don't have any experience with 60i, or combining two kinds of footage, so advice is much appreciated!
    Thanks!

    > that they are not true 30p but really 60i rendered to 30p
    Well, I certainly can't speak for all of these cameras, but I have played around with some of this "30p over 60i" footage -- but most of this was from HDV cameras, not AVCHD. Avoid if you can. Basically, the luma is progressive and the chroma is interlaced.
    I have a function (it's actually part of the dv2film and hd2sd functions) that will deinterlace only the chroma, so can recover greatly true progressive output... but this is an unmitigated a pain in the *** to deal with all the time, and you certainly lose at least a little chroma resolution. Avoid :)

  • How do I import hd 24p footage into premiere pro? Help please

    How do I import hd 24p footage into premiere pro? Help please

    instructions for importing/capturing footage:
    "Capturing DV and HDV video"
    "Importing with the Import commands"
    "Importing with the Media Browser"
    Since you're new to Premiere Pro, I recommend starting here:
    FAQ: How do I learn Premiere Pro?

  • 24p footages to DVD

    Hi everyone,
    I'm a newbie and I filmed a wedding with my Panasonic AG-DVX 100b in 24p mode, so it looks similar to film. I have captured all the footage into FCP-5 using 16:9 letterbox in the timeline and am now ready to finalize it so I can make a DVD in DVD Studio Pro-4. When reviewing the footages that I put in the timeline it looks and sounds great in the Viewer.
    I first used the Quicktime Conversion, then once that was done I converted that by using Compressor. Once everything was done and I viewed everything the quality was bad. I can see block-pixels in most of the scenes and just does not look good at all. Mainly I need to know what settings do I need to set my conversions at? Or is there anything additional I need to do?
    Please help, it would be greatly appreciated...
    Thank You

    IIRC, 24p is 29.97
    If that's true - edit in a standard NTSC sequence (anamorphic or not as appropriate) then export using 'current settings' (not quicktime conversion).
    Drop that file into Compressor and use the appropriate preset for your length of video (60 minute- 90 minute-120 minute) and aspect ratio. Don't forget to select AC3 for the audio. You may want to stay way from 2 pass VBR. Rumor has it that it seems to not work as well as 1 pass CBR in Compressor2.
    Import those files into DVDSP and you should be good to go.
    x
    edit - It is irrelevant what the video looks like in the Viewer. You need to hook up an external NTSC monitor to really see your work. Everything else is a proxy version.

  • Unable to Capture PAL DV footage

    I'm working on a project that requires I edit with both PAL and NTSC footage shot on mini-DV. I was about to purchase a plug-in to convert the PAL footage to NTSC, but find that I can't even capture the PAL footage to begin with.
    I tried using both a deck and a camera as the source device to capture from and they both play the tape just fine and on the camera's LCD (not a PAL camera by the way), I can view the footage perfectly, but still FCP does not acknowledge any video on the tapes.
    I've even tried capturing on iMovie-it tells me that the footage can't be captured because it is 'half-frames' and mentions LP and SP modes. Would this really matter and why does my camera play it just fine?
    Also, when I play the tape on the camera and plug-in to a television, the picture keeps rolling, but again, plays perfectly on my non-pal camera.
    I've tried switching all pre-sets to PAL, but it doesn't help.
    I'm about to make a dub tape with a PAL camera (Sony Z1U) and see what happens, but if anyone has any other suggestions, I'd really appreciate any help.
    Thanks.

    I tried using both a deck and a camera as the source device to capture from and they both play the tape just fine and on the camera's LCD (not a PAL camera by the way), I can view the footage perfectly, but still FCP does not acknowledge any video on the tapes.
    I have never seen an NTSC camera that plays PAL tapes!
      Alberto

  • What is the best way to work with AVCHD 720 24p footage in FCE4.1?

    Hi I have a Panasonic HMC-150 and I've been shooting 720 24p footage at 21 mbps transfer rate.
    I was wondering what is the best way to work with this material in FCE 4.1? I see that in the easy set up menu they only have the option of 1440X1080i at 50 or 60 fps or 1920X1080i at 50 or 60 fps.
    Also in the rates drop down menu there is only 50 or 29.97.
    So I was wondering which is the best choice for 720 24p footage and will it look alright in any of them? Also is it possible to customize these settings?
    And finally can you work with faster transfer rates (21mbps) in FCE?

    Yikes, this is going to be tricky since FCE does not support native 24p editing.
    The work around for some of us is that AVCHD material that is 24p is often recorded to disc at 60i using telecine, in which case it can be editing at 29.97 frames per second, and then detelecined afterward for final export at 23.98 fps. The problem is that I think your camera actually records real 24p - not 24p packed into 60i. When you import the material from the camera what does QuickTime report the framerate as?

  • 24p footage out of sync

    I just imported 24p footage, encoded in SS.
    Encore took it, but the video plays much faster than the audio, and so much that the people are sped up. It looks funny!
    I'm running, CS3 and SS5. The 24p footage with encoded at 12 iFrames and Closed GOPS. The imported audio is a wave file from the 24p project. Even after Encore transcodes the audio the problem remains.
    Any help would be greatly appreciated.

    Not sure of the 'button'.
    One thing you should check though...
    How are you monitoring this? Is your audio following your video to/from the same source?
    Turn on your wave form monitors for the timeline... does the click line up visually on the timeline to the clap of the slate?
    If you monitor your audio off the CPU and your video externally... or your audio out FW and your video only on the cpu... you can get sync issues. Actually LATENCY issues and not really out of sync.
    Are you sure it's out of sync and just not a latency issue?
    Thanks for answering...
    CaptM

  • BLURRY images when I Modify speed in 29.97 timeline with 24p footage

    I am modifying the speed of a clip - only to 90% - and parts of
    the clip appear blurry after I render.
    Any ideas why? What can I do?
    Thank you in advance!

    Is it 24p footage with 3:2 pulldown or, just 24p media?
    Either way, you're in for a fun time.....
    for 24p with 3:2 pulldown, first use Cinema Tools to remove the pulldown. Now, use Cinema Tools to conform it to 2.9.97fps. Now take it into your timeline and adjust the speed.
    For 24p media, just conform it in Cinema Tools to 29.97fps, and then pu in your timeline and adjust the speed.
    What you're doing is avoiding having FCP convert the 24p to 29.97fps by adding frames, before it gets to the speed change. Similarly, 24p with 3:2 pulldown must have it's pulldown removed before you can do a speed change.
    This should make things nicer for you!
    Graeme

  • Canon .mts import 24p footage doesn't work ~

    I was excited to see Premier CS5 could import Canon's 24p footage and had project settings ready for it.
    I was dissapointed to find out that this function doesn't work.  Premier shows my .mts files being 29.97 fps so I'm assuming the camera must inclose the 24p footage inside 29.97 fps container?
    Does anyone know a simpe way to open a .mts file in After Effects, interpret the footage to "Guess 2:3 pulldown" open,  and save export the file back into Premier?
    I can't seem to figure out how to export the interpretted footage from After Effects back into Premier.

    Why are you guys going through all of this trouble?
    Premiere works fine with 24p footage if you shoot it that way.  I use it all the time.  XH-A1 has both 24p and 24pn.
    One is 24p in a 29.97 wrapper and the other is 23.976 native with flags.  Shoot with the one you want and just use the right preset.
    Sorry...I didnt realize you left out the camera you were using.  If it's ont that doesnt have both modes you will need another software to remove the pulldown.

Maybe you are looking for