Catalyst 3560G telnet help

I am unable to telnet, ping, or http into a switch. Although I am able to telnet within switch to switch and ping within also.
I've bounced the switch, made sure I hade enable secret, config line vty, login, password.
I dont know what I am missing on this switch. Any suggs?

Current configuration : 7761 bytes
version 12.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
hostname SWITCHXXX
enable secret xxx
enable password xxx
no aaa new-model
clock timezone EST -5
clock summer-time EDT recurring
ip subnet-zero
ip routing
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface GigabitEthernet0/1
switchport access vlan 36
switchport mode access
spanning-tree portfast
spanning-tree bpdufilter enable
interface GigabitEthernet0/2
switchport access vlan 36
switchport mode access
spanning-tree portfast
spanning-tree bpdufilter enable
interface GigabitEthernet0/3
switchport access vlan 36
switchport mode access
spanning-tree portfast
spanning-tree bpdufilter enable
interface Vlan1
ip address 10.121.X.XXX 255.255.255.0
ip classless
ip http server
control-plane
line con 0
password xxx
login
line vty 0 4
password xxx
login
line vty 5 15
password xxx
login
end

Similar Messages

Option 43 On Catalyst 3560G

Does anyone know if DHCP Option 43 is available on the Catalyst 3560G. I have 3 controllers and I want to make my 1130 series APs join the appropriate controller. I believe DNS is currently being used which is pushing all my APs to the same controller.
Does anyone of instructions on how to configue option 43 on the 3560?
Thanks for any help,

Within DHCP option 43 you can add any number of controller IP addresses. I have not tested if this works or not, but the premise is if the first controller in the list is not available it will use the next.
To configure IOS DHCP server with option 43:
http://www.cisco.com/warp/public/102/dhcp-option-43.pdf
Then go to the IOS section.
Once the AP has connected you will want to use WCS or manually configure the primary/secondary/tertiary controller on each AP. You could get away with not doing this (and allowing DHCP option to provide failover options) but failover time would increase, the AP would most likely need to reload to find another controller (again, untested).

I am a cloud member but i cannot log into business catalyst could you help me

I am a cloud member but i cannot log into business catalyst could you help me
I can log ino all my other adobe program but business catalyst will not let me connect

I will suggest you to reach Business catalyst support team via chat or submit a case using the link (http://www.businesscatalyst.com/contact) and support team will assist you further.
Regards

Web gallery problems in flash catalyst. Please help me!

I've made a web gallery in adobe bridge cs5 that I saved to my harddrive as a swf-file. But when I make a blank page in Flash Catalyst and insert that swf-file nothing happens when I try to view it in "run project". What have I missed. It feels like some file is missing or something. I've tried to import the swf-file in a html document in dreamweaver but it is the same problem there. Can someone help me please?
Thanks
Max

I really appreciate your reply.
but i am still a little bit confused.
Why bookstore1 needs syncronized database conection?
i found the following scriptlet in bookstore servlet of bookstore1 application.
bookDB =(BookDBAO)getServletContext().getAttribute("bookDB");
Does it mean bookDB created here is the same object created in servlet context, that is, they use the same block of memory?
i found the counterpart in bookstore2
<jsp:setProperty name="bookDB" property="database" value="${bookDBAO}" />
Does it mean the bookDB bean duplicates another instance of bookDBAO created in servlet context for its database property ,that is,they don't use the same block of memory?

Bootcamp - Catalyst Control Center - help me!

Hello, I've tried to install catalyst control center for windows 7 bootcamp, I can't seem to find the download for the actual program, I only find the drivers for it, I did find the program once, and installed it, but then I only had 2 different tabs in there, and there should be atleast 7+ with alot of options. I had close to none, in my install of the program, so I uninstalled the whole thing and now I can't seem to find it again.
I've installed the latest driver for the program now, but I cannot find the program...
And ofcourse I want to find out why I only had 2 tabs in there, when I should have had 7+
Please help me
- Anton

Is it these old drivers?
http://forums.macrumors.com/showthread.php?t=1151529
Might repost over here...
https://discussions.apple.com/community/windows_software/boot_camp

Can't publish to Business Catalyst - Adobe Muse - Help!

I'm getting this message when I try to publish my Muse site to Business Catalyst. It was just working, and this dialogue won't accept my password. (Then I logged out, changed my password, and still won't accept the new password.)

Hi,
Most of the MUSE users face this issue when they change their primary id of BUSINESS CATALYST or Adobe ID.
Go to Adobe Business Catalyst site and click on "Get Started for free", click on "Sign In", if Signed in successfully, try to publish from MUSE again
If problem remains same , you need to contact BC Help & support , Go to Live Chat option and let them know your problem.
Hope this will resolve your issue.
Thanks
Prabhakar Kumar

Telnet help

Hi
I want to design a form in Developer6 which will telnet the server and read the output of telnet data then save into text file.
Can any one help me
BR//

Hello,
Use the HOST() built-in to run external programs like telnet. You could use a batch comand file for the telnet input like (not tested)
Host('cmd /c telnet < c:\telnet.txt');Francois

ATI Catalyst Install Manager and catalyst Control Center Help

I just run the Windows 7 Upgrade
advisor report and it said that I should uninstall the ATI Catalyst Install Manager and Catalyst Control Center then reinstall after upgrade..
Could someone direct me where I might t find these programs for Windows 7

You must not do this. Just continue upgrade installation.
On my Satellite I got the same message but I have simply continued with upgrade.
At the end everything went fine.

Cisco Catalyst 3560G 48, PSU

Hi
I have several Cisco Catalyst switches 3560 / 3750 etc.
There is a connector for remote PSU in the back.
Is this an input for redundant power?
Where can I find the pin layout?

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Sounds like you've found the connector for an external RPS. I don't know if Cisco documents the pins, and the RPS might "talk" with switch, so more might be involved they providing some voltage on those pins.

Switching from Flash to Flash Catalyst/Flex

For the last few years I have been developing applications for project reporting. To explain this in simplest terms, my clients give me hundreds of reports and supporting documents, graphics, videos, etc. which I then condense and reorganize into a presentation/application in Flash. The project is then published as an .exe to be burned to CD ROM or DVD along with any supporting files and is then distributed to project stake holders, investors, etc.
I'm considering the possibility of a switch from Flash to Flash Catalyst/Flex and want to outline what my needs are, here in the forum, in hopes that others now using Catalyst/Flex can help me decide if this is an appropriate move.
Features needed:
1. Basic animation, transitions, etc.
2. Full Navigation (up to 3 levels) for up to 300 slides.
3. Keyboard navigation (PageUp/PageDown) to navigate sequentially through the entire presentation.
4. Linking into other applications and documents - Word, Excel, Power Point, etc.
5. Full Screen Mode
6. Slide Show Mode
7. Search Features
8. Slide sharing (via email)
9. Video and audio w/controls
10. Pan and Zoom w/controls (panning and zooming of graphics and .swf files)
11. Scrolling (scrolling of text, graphics and .swf files)
12. Interactive forms
Can anyone please comment specifically on these features and wether or not they are possible using Catalyst and/or Catalyst/Flex in combination.
Thank you all for any insight or suggestions.
John

With the exception of making fre-form animations (like a cartoon for example), everything you can do in Flash can be done in Flex considerably faster.
The downside is that Flex applications (especially ones designed in Catalyst) are generally larger, and consume more memory. Personally, I never publish anything made in Catalyst without optimizing it in Flash Builder first.
If the drop in operating performance isn't a deal breaker (most of the time you can't even notice it), then I would certainly consider moving to Flex going forward on new projects.

Troubleshooting Fiber Connection on a Catalyst 2960

I am trying to test my fiber connectivity on a Catalyst 2960 before I deploy it. So what I thought I would do is connect it to another switch in my office with a open port for the fiber connection. The other switch is a Catalyst 3560G. Here are the port configurations:
interface GigabitEthernet0/2
switchport trunk allowed vlan 1,100
switchport mode trunk
macro description cisco-switch
interface GigabitEthernet0/25
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,100
switchport mode trunk
The first one is the catalyst 2960 and the 3560G is the second.
When you show the interface for each of these it shows that it recognizes the media but the line protocal and the GigbitEthernet Port is down.
Any Ideas?

Sorry... a fiber optic cable with a connector on each end.
To aid in troubleshooting, many times we loopback the signal back to the originating device. An optical loopback is just connecting the transmit (Tx) to the receive (Rx).
The multimode SFP/GBIC transceiver you are using will allow you to directly connect the Transmit and Receive ports without damage to the unit. This should provide you with a green link LED.
If so, then you can reconnect your fibers and loopback (connect the two fibers together) at the far end of the fiber link (use an optical adapter) and see if you get a green LED.

Import Business Catalyst site into Dreamweaver {subject edited by moderator}

I created a website using Dreamweaver CC. I added business catalyst extension and want to use its feature for the site I created within Dreamweaver. However, every time I tried to open up the business catalyst section, it wants me to create a new trial site. How do I skip this step and integrate what I already created using Dreamweaver CC? I don't want to have a trial site. I want to use what I already created using Dreamweaver CC with the business catalyst extension. Help!!!!

I'm afraid that's how Business Catalyst works. You can't just upload any site to BC servers. You must first create a BC account, create a BC site template, edit your template, activate BC modules, etc... If all you want is to host your DW site without rebuilding it with BC, I suggest you look for commercial web hosting someplace else.
Nancy O.

How can I create Business Catalyst editable slideshows in Muse?

I've created a series of slideshows in Adobe Muse but my client cannot edit them in Business Catalyst.
Please help!
http://www.timelinemissions.com/work.html

If you like to have a constant amout of imgs, lets say 3, you can define the images as a InContext Editable image and the caption as a InContext Editable line. I usally prerer this solution in front of WebApps as the customer can edit almost everything using ICE-mode.
Please refer to the ICE documentation for more details of implementation.
If you need a more flexible solution I would recommend a WebApp with a field that you define as a image. Then add new WebApp items for every image. If you like to limit the size of a image you can use BC Thumbnail tool. I think Joe Watkins has talked about how to use this tool before.

Switching to Business Catalyst from Shopify

Hi, I currently have a shopify site here. But, after seeing Business Catalyst through a friend of mine who uses it I want to change over. However, I really don't want to change the look and feel to much. Would it be possible somehow in keeping the look and feel if I make a change over to Business Catalyst?
Any help would be appreciated.

Someone who's familiar with HTML/CSS and Business Catalyst would have to convert it. You can retain a lot of the same styles as you had before but you'd have to update new BC layouts and templates to replicate the markup on your site so the content is styled appropriately.
It looks like you are using Paypal and your categories and products aren't too complicated so it would probably fit like a glove. It's very easy to add/update a BC site once it's been designed by a web designer but to port your site over will require someone who's very familiar with web authoring. Look to your BC partner for help here if you have one.

Lost catalyst control center and switchable grphics

Hi i accedintly deleted all of ati folders in my pc and reinstalled the new amd for the driver and lost switchable grphics options in my pc now i dont know what should i do to restore the switchable graphics setting in my laptop or the old catalyst control centerplease help me

Hi, Download and run the AMD installation package on the following link - this provides both the drivers for your switchable graphics, including the customised Catalyst Control Centre. http://ftp.hp.com/pub/softpaq/sp55001-55500/sp55025.exe When the installation has completed, restart the notebook. Regards, DP-K

Catalyst 3560G telnet help

Similar Messages

Maybe you are looking for