Checking performanc​e of reference to controls

Hello,
I'd appreciate if somebody can look at the attached Vi and tell me if the bench mark is right. I'm checking what method is better to use when I change the value and when I change a property of a series of controls in the FP.
Apparently, the use of References for changing the values is a very slow one.
Thank you for any comment or suggestion.
Marce
Attachments:
ReferencesBenchMark.vi ‏113 KB

You are loosing most performance during the property node read/write...but...once you have done this...you loose little more by accessing the "value" property while you are there. So, if you need to access the property node for a property...go ahead and use the value property while you are there...otherwise there are faster ways. (Local Var/Wire)
regards,
Brett Burger

Similar Messages

  • Reference to control different from reference panel- controls[]

    Hi, I get references to all my objects on front panel from the properties panle->controls[]. In my program I use an Event case and the reference to the contol passed from the Event Case is different fom the reference obtained by panel->controls[]. I need this to be the same since I want to use this reference to search for match in ref array from panel->controls[] get the array index of thet control

    Do you have tabs\arrays\clusters?
    The references from controls in those (and possibly other structures) are not returned when you use the Controls[] property.
    You have to go over all the references and if any of them is one of these structures you need to cast it to its specific class and extract its Controls[] property to get to the controls in it. This needs to be done recursively until there are no more structures.
    I seem to remember seeing a VI somewhere that did this (maybe OpenG?), but I can't seem to find it. Maybe someone else knows.
    Try to take over the world!

  • Performing check and potential update for status control table

    Cheers Experts,
    I searched in the forum, but I didn't find an answer.
    I'm working on a 3.0B BW system.
    After updating from PSA to an ODS, in the log I see the following line:
    "Performing check and potential update for status control table" and double clicking on it, it says:
    If data is loaded into an InfoCube, or existing data is edited (aggregated/compressed/deleted/got from a DataMart), then there is a change in  the potential reportability of the data , or the possibility of deleting data by request, or of aggregating or compressing.
    This status of each one of these Cubes is stored in a status table, that is updated when there is any change to the status of a request in the Cube.
    The system now analyzes the requests in the Cube and compares the calculated status with the status table.
    If deviations from the status table arise then you are given the option of adjusting the status table.                                         
    I have 2 questions:
    1) What is BW doing, mainly because I'm working on an ODS and not an Infocube?
    2) What can I do to reduce its execution time, since it lasts several minutes?
    Thanks and greetings.
    Roberto

    Roberto, did you ever find an answer to your question?  We also are experiencing long runtimes during this particular process running 3.x deltas from ODS to ODS and cubes.

  • I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work eithe

    I just got an iphone 4 yesterday. I got everything all set up and working great. When I woke up last this morning, my ipod has no sound and the albums covers are all mixed up. I've checked all my settings and volume control. My text sound won't work either. However, my ringtone works just fine.

    Have you taken the steps recommended in the User Guide:  restart, reset, restore?

  • Sound has stopped. Have checked speaker, side switch and volume controls.

    Sound has stopped.  Have checked speaker, side switch and volume control.  Anything else?

    Sounds for what? Music, apps, alerts? Or all?
    Make Sure iOS is updated to the latest version
    Reboot the device by pressing and holding down the home and sleep/wake buttons (power) at the same time until the apple logo appears on the screen, then let go.
    If that doesn't work then reset the device by going to settings/general/reset/reset all settings

  • Sort detail Check/cheque by the Reference Document Number (REGUP-XBLNR)

    Hi Experts,
    I'm an Abaper and I don't Know very much about this topic, so my question is: How can I sort the detail Chek/cheque by the Reference Document Number (Field REGUP-XBLNR)?  Now is sorted by the Document Number of the Payment Document (Field REGUP-BELNR).
    I've searched in the control program of Sapscript to print the Check/cheque but I haven't found anything about sorting the datail
    Thank you for your time and help.
    Regards.

    Hi Marco,
    You can add the feild of the cheque no via spl.feilds T.code : O7R3/OBVU ( sap  standard report  eg. FBL3N,etc).
    Select the the table payr and add the feild chect.
    After addition of the above feild,do run the program RFPOSEXTEND.
    Once you complete the above mentioned activity,when  system the will pick the checque no in FBL3N.
    Hope that  your issue wil be solved.
    If not,do revert.
    Regards

  • Internal Order Budget Check for PO with reference to PR / RFQ

    Hi All,
    I have a scenario where the budget availability control is not working for PO created with reference to PR or RFQ. While creating the PO if i modify the PO value more than RFQ or PR value then system is looking for budget control.
    If we create a direct PO system is checking for Budget control where the PO value is more than availability budget.
    We have the budget control check with internal order for services and non stock material based on substitution rule created for cost element group and cost center group.
    In tolerance limits budget availability control we have not activated for PR, itu2019s activated from PO.
    Kindly let me know what is the reason for budget availability control is not active where the PO is created with reference to PR or RFQ.
    Thanks & Regards,
    Rama Mohan

    493900 - FAQ: Release Strategy:
    It is not possible to create a purchase order if the referenced purchase requisition is not released. But the system allows you to put the purchase order on hold and then release the purchase requisition.
    On the other hand you can create a purchase order with reference to an unreleased request of quotation.

  • How to add check box in SAP B1 grid controls..

    hi all,
    Anyone know how to add check box in SAP grid control?
    It will be great if you could show me some sample code.
    thanks.
    regards,
    sohch

    Hi Sohch,
    1. First of all you should define the Column in a matrix as it_CHECK_BOX. Like
            oColumns = oMatrix.Columns
            oColumn = oColumns.Add("chk_YesNo", SAPbouiCOM.BoFormItemTypes.it_CHECK_BOX)
            oColumn.TitleObject.Caption = "YesNo"
            oColumn.Width = 60
            oColumn.Editable = True
    2. Bind it with a DBDataSource as defined
            oColumn = oColumns.Item("chk_YesNo")
            oColumn.DataBind.Bind("UDTable", "U_YesNo")
    3. Make Sure that the value that is being put into the Database is either 'Y' or 'N'.
    Hope this Helps
    Rizwan Hafeez
    Team Lead
    SAP Addon Development Section
    Abacus Consulting - Pakistan

  • How can i get the reference to Controls from VI-reference

    Hello,
    i have a VI with ~5 controls on it.
    And with the Object "Current VIs path" and "Open VI reference" i can create a reference to the current VI.
    How can i create now a reference to the controls? (Starting with VI-reference?
    Of course i know how to create directly a reference from a control.
    My idea wasm that there areperhaps properties like:
    - Number of controls
    - Name of control
    - Type of control (string, bool. number...)
    Is this somewhere there and i just dont find it?
    Thanks for your help

    Once you have the VI Refnum, it's a two-step process. Wire the VI Refnum into a property node and get a reference to the Front Panel. Output the Front Panel reference into another property node and select the property Controls[ ], which outputs an array of references for all the controls on the front panel.
    Message Edited by Jarrod S. on 04-20-2007 11:06 AM
    Jarrod S.
    National Instruments
    Attachments:
    get_ref.PNG ‏5 KB

  • Reference to control on main front panel fails when subvi front panel is closed?

    Hi All,
    I'm experiencing an odd bug. In my code, I use a subvi to control a piece of hardware. This subvi has controls for all of the functions of my hardware.
    I'm changing the value of one of these controls from my main front panel by running a reference to a knob on my main front panel into the subvi, grabbing the value of the knob with a property node, and then updating the value of the subvi control using a signaling property node.
    This works fine when my subvi front panel is open but fails to work at all when the subvi front panel is closed.
    I'm new to labview , so any help is appreciated.
    Thanks,
    Arpan
    Solved!
    Go to Solution.

    What is your LabVIEW version?
    Front panels that are not shown are typically not updated and might not even be loaded into memory.
    The presence of certain code elements (e.g. property nodes) often forces the front panel to be in memory even if it is not shown, but I haven't studied it in a long time so there might be subtleties. Maybe somebody from NI can give more details.
    If it does not work unles the FP is open, open the front panel minimized to avoid distraction.
    Can you attach some code? Maybe there are better ways to do all this anyway.
    LabVIEW Champion . Do more with less code and in less time .

  • How to check validity of data reference

    Hello everybody,
    in my application I use a help class to buffer data objects.
    This class contains one attribute which is an internal table ( columns: DATAID and DATAREF )
    I use this databuffer to transport data between different classes.
    Now I did the following mistake:
    First I call the method 'METH_CHECK'. As import parameter I pass a reference to my databuffer class.
    In method 'METH_CHECK' I call a function module 'FUNC_1' passing my reference to my databuffer class.
    In 'FUNC_1'  I declare a local variable 'lv_value'.
    Then I use the statement 'GET REFERENCE OF lv_value' and save this reference into my databuffer class.
    After processing functions / methods I´m back at the point where 'METH_CHECK' was called.
    When I check my databuffer class, I´ve got one entry in it.
    The reference I saved while processing 'FUNC_1' . But the referenced data has already be freed ( remember, it was a local variable ).
    In the debugger I see the column where I save the references to data objects.
    The field value has changed from a valid reference to i.e. 'FREED ITAB: 5'...
    OK, I know what is wrong... No problem in my application, but I want to clean
    this entry... How can I check this...
    I can not check like
      LOOP AT me->buffer INTO wa_buffer.
        IF wa_buffer-data IS INITIAL.
          DELETE...
        ENDIF.
      ENDLOOP.
    or
      LOOP AT me->buffer INTO wa_buffer.
        IF wa_buffer-data CP 'FREED'.
          DELETE....
        ENDIF.
      ENDLOOP.
    How can I notice an invalid reference at this point?
    Thank you very much,
    Oliver Seifer

    Hello Oliver,
    Another approach might be to avoid any dependency to the caller at all.
    Regards
      Klaus
    data:
        buffer_Reference  type ref to data.
    field-symbols:
       <buffer_Data> type data.
    create data buffer_Reference like i_Value.
    assign buffer_Reference to <buffer_Data>.
    <buffer_Data> = i_Value.

  • How do I use javascript or formcalc to reference child controls (not by name)

    Hi everyone,
    I've created a ton of reports in the past, and I'm now looking at creating some reusable objects so that other people can use advanced form functionality without having to learn to use scripts.
    A lot of the coding was acheived using this, .parent, etc. so that they can rename controls and subforms without having to worry about breaking scripts. One issue that I am having is that Some of my code looks at children controls, and references them by name (for example, I have some code that uses setfocus to move the user to the first field in a subform).
    In most languages, there are ways to refer to child controls via an indexer or an items/children array. i.e. Subform.items[0].rawValue.
    I know that this would pose some issues, but I think I could sort it out, if only I knew where to start. Is there some way to reference a child control without it's name?
    Thanks for your help!
    - Scott

    Hi Scott,
    The subform has a nodes collection you can loop though, as you suspected.  If might show up more than you want but you can test the className to see if it is a field and then ui.oneOfChild.className to work out what type of field. So;
    for (var i = 0; i < Subform1.nodes.length; i++)
        var n = Subform1.nodes.item(i);
        console.println(n.className + " " + n.name + " " + n.ui.oneOfChild.className);
    Hope this helps.
    Bruce

  • Check for a row in table control

    I have a table control and on a click of a row in a particular column (vertically downwards) i want to check which row of that column is clicked because i want search help of that column different for every row.
    how can i do it

    hi,
    In the struicture having the table control fields add a field 'sel type c.
    In the screen in table control consider single line selection and enter field name as sel. activate the screen layout.
    In PAI,
    loop atthe table control table and read the row where sel = 'X'.
    Now write your serach help code for the corresponding column and row.
    Thanks,
    Kasiraman R

  • Obtaining References of Controls Inside of Tab Controls

    Does anyone have a way to detemine the id/index number of a control on a tabbed front panel? If there is no front panel I can use the menus: Edit, Set tabbing order. Then I can use this index in the block diagram of a sub-vi to update the control on the main fornt panel with data from the sub-vi as it runs. Yet, if you do the same thing on a front panel with a tab display, only the tabbed pages are indexed, as opposed to the individiual controls and displays. 
    Thanks.
    Brian

    I have a way of updating a control on the main vi by using an open vi reference to the main vi in my sub-vi (see code below). This is working fine for situtations where the main vi does not have a tab control. With this vi that you gave me, how can I reference a specific control in the table, such as the 3rd control on the 3rd page..and more generally the n-th control on the n-th page such that my "2" below is correct. Currently I just wire a numeric to an index array and the value is then sent to that control. the trouble that I am having is in the "get all controls" & "pick the control" part below. With the tab control on the front panel, I cannot simply wire a numeric like I did below with the "2".

  • Checking in and out files (source control) in form 6i

    Hai,
    how we can make use of source control options in form 6i.
    thnaks and regards
    vivek

    Hi there
    From what you have posted it would appear that you are using RoboHelp for Word. I don't believe RoboHelp for Word has ever been configured to integrate with RoboSource Control.
    If you were using RoboHelp HTML, it is actually configured to work with RoboSource Control and is totally integrated where as you work on topics they are checked out automatically.
    You may wish to review the article linked below.
    Click here to view
    Cheers... Rick
    Helpful and Handy Links
    RoboHelp Wish Form/Bug Reporting Form
    Begin learning RoboHelp HTML 7 or 8 within the day - $24.95!
    Adobe Certified RoboHelp HTML Training
    SorcerStone Blog
    RoboHelp eBooks

Maybe you are looking for