Cisco 2620 Adsl WIC

My 2620 will not recognise a ADSL WIC card. I have tried a number of ios but none work. Also I have 8mb of flash on my router and some bin files less than that size will not load using xmodem saying there is not enough space. Any ideas on how to get the router to see the card will be greatly appreciated

Quoting from CCO:
"The Cisco 2600/3600/3700 series routers require a PLUS Cisco IOS Software image for ADSL if version 12.2T is in use. From Cisco IOS Software Release12.3 mainline and later, ADSL WIC support is available in the "IP Base" feature set."
So you will need to download an appropriate image to get your router to recognise the card. Since you only have 8Mb of Flash, you will either need to upgrade your flash to 16Mb or boot via TFTP.
Hope that helps - pls rate the post if it does.
Paresh

Similar Messages

Could Cisco 1701 ADSL Router supports WIC-1ENET Card.

Hi,
I need advise as to if a Cisco 1701 ADSL router could support WIC-1ENET Card.
My 1701 Router has WIC 0 as ADSL and WIC 1 as ISDN, could the ADSL card be replaced by a WIC-1ENET. I noticed ,that the cards seems to be rivet onto the back of the Router and not connected with SCREWS as other routers would posses.
Could someone advised as to how i can have this router supports 2 Ethernet NICs or what could be your recommendations?
Thank you,
Cisco End User.

Hello,
the WIC-1ENET is supported on the 1701, but, AFAIK, only in slot 0.
It does not support 2 WIC-1ENET cards, only the 1720, 1750, and 1751 do, with a specific IOS release, check out this info from CCO:
WIC-1ENET- Support for two Ethernet WICs
The Ethernet WIC (WIC-1ENET) provides the capability to deploy additional Ethernet port(s) in a Cisco 1700 series routers. The initial release of the WIC-1ENET supported only one WIC-1ENET card in a 1700 router. The new IOS 12.2(2)XJ release offers the option of deploying up to two WIC-1ENET adapters in a Cisco 1720, 1750, or 1751 router. A total of three Ethernet ports can be configured. A typical application that requires three Ethernet ports involves using the built-in 10/100 Fast Ethernet port for LAN segment. One of the WIC-1ENET port could be used for high-speed broadband DSL or cable modem connection. The second WIC-1ENET port could be used for a DMZ (demilitarized zone) environment for deploying public Web servers or FTP servers. Hardware modification is not necessary to use the capability of IOS 12.2(2)XJ. The new IOS software is compatible with WIC-1ENET adapters already installed in 1700 series routers.
HTH,
GP

Help with CISCO-887VA adsl over pots and PPPoE with dynamic IP

Hi
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.
I'm trying to setup PPPoE with dynamic IP
Followed CISCO's documentations but the commands used were not recognized by the router. Any simple working config for me to follow will be enough.
I'll appreciate any help. Thanks a lot!
here's my config.
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
ip source-route
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server x.x.x.x x.x.x.x.x
lease 0 2
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGLxxxxxxx
controller VDSL 0
ip ftp username cisco
ip ftp password cisco
interface Ethernet0
pppoe enable group global
pppoe-client dial-pool-number 1
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip directed-broadcast
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
ppp pap sent-username xxxx password 0 xxxx
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip access-list standard 1
permit 10.0.0.0 0.0.0.255
no cdp run
line con 0
line aux 0
line vty 0 4
login
transport input all
end

Try to check with your ISP the modem string to use for VDSL
and some ISP support direct dhcp on Ethernet0 without PPPoE.
An equivalent config is working for me in Switzerland with Swisscom.
N.B. "modem" under VDSL controller is enable using service internal !
service internal
controller VDSL 0
operating mode vdsl2
modem co5
ip source-route
ip cef
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server 8.8.8.8
lease 0 2
interface Ethernet0
ip address dhcp
ip nat outside
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
ip nat inside source list 23 interface Ethernet0 overload
access-list 23 permit 10.0.0.0 0.0.0.255
end

Cisco 2620 eigrp/ospf issues

Greetings,
I'm having issues getting a Cisco 2620 and a Dell Powerconnect 6024 to redistribute via eigrp/ospf correctly which are both at a remote location. I have attached a basic diagram to better show the topology. We have been unable to access the remote site from our main site (which is using a cisco 3600) without a static route for each subnet at the remote site. Hopefully this makes sense.
Cisco 2620 Config:
Building configuration...
Current configuration:
ip subnet-zero
lane client flush
cns event-service server
interface FastEthernet0/0
ip address 10.100.187.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0
ip address 10.100.181.10 255.255.255.252
no ip mroute-cache
no fair-queue
router eigrp 100
redistribute connected
redistribute ospf 1
network 10.0.0.0
no auto-summary
router ospf 1
redistribute connected
redistribute eigrp 100 subnets
network 10.100.0.0 0.0.255.255 area 0.0.0.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.100.181.9
no ip http server
banner motd ^CCC

Timothy
There are a couple of things that I am not clear about concerning your situation. Your diagram shows a single subnet between the Cisco and the Dell. Is everything in the Dell in that single subnet? If so I am not sure why you are running OSPF, since there will not be any OSPF routes to redistribute.
If the diagram is incomplete and there are routes in OSPF that need to redistribute to EIGRP then there is an issue in the configuration. There is no default metric configured under router EIGRP. Without a default metric routes from another protocol (OSPF) will not redistribute into EIGRP.
I think it is also an interesting question whether the 2620 and the 3600 routers are forming EIGRP neighbor relationships. Failure to form EIGRP neighbor relationships could also cause the symptoms that you describe.
HTH
Rick

VOIP home lab with cisco 2620 and VIC-2FXO port

Hi all,
I m considering building a home lab for studying CCVP, the lab would be based on the follow components :
- CUCM 8.X (already installed)
- A couple of soft phones running in VMWARE with IP Blue and CIPC (they are already in place and registered with the CUCM)
- Cisco router 2620 with NM-2V and VIC-2FXO-M2 (for europe, I'm in France)
so here are my questions :
1/ it looks like the NM-2V comes with integrated DSP, so I should not need more DSP, I have got one PSTN analogic line only so I can make only one call at a time, please confirm
2/ my analog line comes via my home internet provider dsl box, i have already tried to connect an analog phone and it works, please confirm the router will be able to receive and place calls
thanks for your help, I m looking forward to begin my voice lab

1. Yes, the NM-2V has built-in DSP resources for up to four calls (max voice port density with two 1st generation VICs). You cannot add further DSP chips to the NM-1V/2V, nor would you need to for what it does. You have one PSTN phone line, thus you can only make one call at a time. If you had a second line you could use the other FXO port for a second concurrent call.
2. If the phone line works then it will work with the router to make and receive calls. As Gregory said, just configure dial peers for what you need to do.
Here is some info on the NM-2V:
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_tech_note09186a0080094ac0.shtml

Making a VoIP call with the Cisco 837 ADSL router

I would greatly appreciate if could please provide some technical assistance to my questions below:
Is it possible to make a VoIP call between two 837 ADSL Cisco routers over a 1Mbps ADSL broadband connection?
If so, can I configure this VoIP connection using either a PPPoE or ATM WAN link?
Is it possible to make a VoIP call using a Cisco 837 Router while simultaneously surfing the Internet? In other words do I need two public IP addresses i.e. one for accessing the internet and one for making the VoIP call or is one static IP address obtained from my ISP sufficent.
It is possible to configure QoS parameters (e.g. RSVP, Voice precedence, Voice codec selection) on this 837 router using PPoE or can it only be done using an ATM WAN interface?
Does the Cisco 837 router support both the H.323 and SIP communication protocols? Do I need to purchase a certain IOS operating system version for VoIP calling?
Does the VoIP dial peers need to be configured with both a POTS and VoIP phone numbers or is only one number required?
Do I need to obtain a special VoIP number from my VoIP service provider? or can I use existing POTS numbers or made up numbers within the dial peers as this situation involves making a private VoIP call between two branch offices using 837 ADSL routers and not via a VoIP service provider.
Finally, can I use POTS ordinary telephones with the Cisco 837 for making VoIP calls or do I strictly need to purchase VoIP phones?
My apologies for the number of questions asked here but I currently need to know the technical ability of the Cisco ADSL 837 as I am thinking of employing these routers in my company organisation.
I await your feedback in due course.
Thanks,
Martin Healy

Hi,
I give you a sample config of my router.
class-map voice
match access-group 101
policy-map mypolicy
class voice
priority 128
class class-default
fair-queue 16
ip subnet-zero
gateway
interface Ethernet0
ip address 20.20.20.20 255.255.255.0
no ip directed-broadcast (default)
ip route-cache policy
ip policy route-map data
interface ATM0
ip address 10.10.10.20 255.255.255.0
no ip directed-broadcast (default)
no atm ilmi-keepalive (default)
pvc 1/40
service-policy output mypolicy
protocol ip 10.10.10.36 broadcast
vbr-nrt 640 600 4
! 640 is the maximum upstream rate of ADSL
encapsulation aal5snap
bundle-enable
h323-gateway voip interface
h323-gateway voip id gk-twister ipaddr 172.17.1.1 1719
h323-gateway voip h323-id gw-820
h323-gateway voip tech-prefix 1#
router eigrp 100
network 10.0.0.0
network 20.0.0.0
ip classless (default)
no ip http server
access-list 101 permit ip any any precedence critical
route-map data permit 10
set ip precedence routine
line con 0
exec-timeout 0 0
transport input none
stopbits 1
line vty 0 4
login
voice-port 1
local-alerting
timeouts call-disconnect 0
voice-port 2
local-alerting
timeouts call-disconnect 0
voice-port 3
local-alerting
timeouts call-disconnect 0
voice-port 4
local-alerting
timeouts call-disconnect 0
dial-peer voice 10 voip
destination-pattern ........
ip precedence 5
session target ras
dial-peer voice 1 pots
destination-pattern 5258111
port 1
dial-peer voice 2 pots
destination-pattern 5258222
port 2
dial-peer voice 3 pots
destination-pattern 5258333
port 3
dial-peer voice 4 pots
destination-pattern 5258444
port 4
end

Cisco 851 ADSL site-to-site VPN support

Hi expertise ,
we have 4 offices connected to internet via 1mpbs adsl connection. i have in all those sites cisco 851 dsl router. is possible to connect all offices togher using this model? we need to run voice mainly between offices, is 851 model capable to do site to site vpn between all offices.
hope got answer from you experts

Tariq,
Yes with that model L2L VPN's are possible - it depends on 2 factors:-
1) The version of IOS you currently have needs to have the crypto features - if not you need to download and install
2) One of the sites needs to be the HUB - with a static IP address for the DSL link. You cannot created a VPN connection between 2 devices that have DHCP assigned addresses.
For configuration examples see the below:-
http://www.cisco.com/en/US/customer/products/hw/routers/ps380/prod_configuration_examples_list.html
HTH>

ISDN dial-in with Cisco 1721 and WIC-1B-S/T

Hi there,
we use a Cisco 1721 with a WIC-1B-S/T interface for ISDN backup purposes. I configured the Cisco 1721 and connected the BRI-WIC to a ISDN channel. When I try to test the ISDN connection, I always get the error that the line protocol is down. The WIC is connected to the ISDN correctly. I do not understand why the line protocol is always down. Could anybody help? The chosen encapsulation is PPP, the ISDN Switch Type is basic-1tr6 (I think thats the right one for Germany). The IOS version is 12.4 (1c).
Regards, J. Schroeder

Hi there,
the BRI interface is connected to a telephone system and not directly to a NTBA. The hostname matches the username, is this right? When I try to dial out, I get this messages:
*Mar 9 16:28:11.804: ISDN BR0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8003
*Mar 9 16:28:33.792: ISDN BR0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8003, event 0x5 ces 1
*Mar 9 16:29:47.324: ISDN BR0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8004
*Mar 9 16:30:09.312: ISDN BR0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8004, event 0x5 ces 1
*Mar 9 16:30:12.952: ISDN BR0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8005
*Mar 9 16:30:34.940: ISDN BR0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8005, event 0x5 ces 1

Cisco 876 ADSL over ISDN Router

I am facing some problem in using ISDN bri S/T interface for connectivity to HO PRI router.I am not using the ATM interface of this router.The isdn status always shows that the isdn layer 1 and 2 is deactivated. IF i connect the same bri cable to other isdn router it works fine.
Is their any special configuration or command required in 876 router for the isdn dialing?
I found on cisco that the 876 router ISDN bri S/T interface is for the out-of-band mangement and dial backup.
Can i use this interface for the normal isdn dialing?
need some clarification.
regards,
khalid siddiq

Find the attach detail.
SCIENTECH-AVEER#
SCIENTECH-AVEER#sh runn
SCIENTECH-AVEER#sh running-config
Building configuration...
Current configuration : 1505 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname SCIENTECH-AVEER
boot-start-marker
boot-end-marker
username INET-Rou-ESA password 0 cisco123
no aaa new-model
ip subnet-zero
ip cef
no ftp-server write-enable
isdn switch-type basic-net3
isdn tei-negotiation first-call
interface BRI0
description connected to HQ PRI
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
ppp authentication chap
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
shutdown
interface FastEthernet2
no ip address
shutdown
interface FastEthernet3
no ip address
shutdown
interface Vlan1
ip address 192.168.201.25 255.255.255.0
interface Dialer0
ip address negotiated
encapsulation ppp
dialer pool 2
dialer string 404444
dialer-group 1
router rip
network 192.168.201.0
network 192.168.251.0
ip classless
no ip http server
no ip http secure-server
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
control-plane
line con 0
password gbm4ibm
login
no modem enable
transport preferred all
transport output all
line aux 0
transport preferred all
transport output all
line vty 0 4
password gbm4ibm
login
transport preferred all
transport input all
transport output all
scheduler max-task-time 5000
end
SCIENTECH-AVEER# sh ver
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.3(8)YI2, RE
LEASE SOFTWARE (fc1)
Synched to technology version 12.3(10.3)T2
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 14-Jun-05 18:58 by ealyon
ROM: System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE
ROM: Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.3(8)YI
2, RELEASE SOFTWARE (fc1)
SCIENTECH-AVEER uptime is 22 hours, 13 minutes
System returned to ROM by reload
System image file is "flash:c870-advsecurityk9-mz.123-8.YI2.bin"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 876 (MPC8272) processor (revision 0x100) with 118784K/12288K bytes of memo
ry.
Processor board ID FCZ100223M7
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ISDN Basic Rate interface
1 ATM interface
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102

Cisco 1701 adsl not connecting??

Hey guys,
I'm using sdm to do a quick setup on my router i managed to setup using the quick wizard and i setup the pppoe connection but i don't think it's connecting because i am getting dns error when i try to browse. Am i missing a step??? Do i need to open something after i create the connection???
Where can i get a status to see what the problem is?

Ok guys this is driving me mad please tell me what i am missing.
I have reseted to default.
Access router via ip and used SDM software to configure the basics such as DHCP,pppoe and so on.
This is the print.
Building configuration...
Current configuration : 2469 bytes
! Last configuration change at 14:12:33 PCTimeZ Fri Jun 2 2006
! NVRAM config last updated at 14:12:42 PCTimeZ Fri Jun 2 2006
version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname gateway
boot-start-marker
boot-end-marker
logging buffered 51200 debugging
logging console critical
enable secret xxxx
username root privilege 15 password xxxx
clock timezone PCTimeZone 0
no aaa new-model
ip subnet-zero
no ip source-route
ip dhcp excluded-address 10.10.10.1 10.10.10.19
ip dhcp excluded-address 10.10.10.41 10.10.10.254
ip dhcp pool sdm-pool1
network 10.10.10.0 255.255.255.0
default-router 10.10.10.254
ip tcp synwait-time 10
ip domain name domain.com
ip name-server 203.0.178.191
no ip bootp server
ip cef
ip audit notify log
ip audit po max-events 100
no ftp-server write-enable
no scripting tcl init
no scripting tcl encdir
no crypto isakmp enable
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
description Adsl PPPoe
pvc 8/35
pppoe-client dial-pool-number 1
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
interface FastEthernet0
description $FW_INSIDE$$ETH-LAN$
ip address 10.10.10.254 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
ip tcp adjust-mss 1452
speed auto
interface Dialer0
ip address negotiated
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap callin
ppp pap sent-username [email protected] password xxxx
ip classless
ip http server
ip http authentication local
ip http secure-server
logging trap debugging
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
scheduler allocate 4000 1000
scheduler interval 500
end
gateway#

Strange issue - unable to establish PPP with Cisco 887 VAG router on one particular ADSL line

I have a strange problem that I’m struggling to get to the bottom of with my ISP and wondered if anyone could help.
We have a site with an older Cisco 877 ADSL router which was working happily until a few weeks ago when the connection dropped suddenly (out-of-hours at 2am if that’s of any significance – made me think most likely something carrier/ISP related?)    When connectivity was lost, the router could sync with the BT exchange (we are in the UK) but could not establish PPP.
We logged fault with our ISP – after some to’ing and fro’ing, they passed it onto BT and their engineers visited site, they fixed “a line fault” (we don’t get much detail on what was actually fixed) but we still could not establish connectivity – same thing, solid CD light but no PPP.
So, we replaced the router with another 877 – same again, solid CD but no PPP. We replaced all the cables and microfilter etc but no difference.
We tried a different Cisco router (a newer Cisco 887VAG) which, as I understand, uses a different modem chipset but no matter – PPP could still not be established. We tested this router on another ADSL line with the same ISP and it worked without issue, using the same ADSL account details, it was able to establish connectivity. So we figured this must still be a BT/ISP issue.
Since then we’ve had BT out again twice but they say there is no fault. The ISP say there is no issue with them. But we still cannot establish ADSL connectivity on this line, despite having tried 3 different ADSL routers and despite the fact the routers work with the same account details on another ADSL line.
The 887VAG router we have currently connected has 3G backup so that is keeping us going in the meantime and also means I can login to the router remotely to check on the ADSL status.
But I’m struggling to pinpoint where the problem may lie.   Strangely, if I turn on PPP negotiation and authentication debug then I’m not actually seeing any output from it at all?
Yet, the ATM interface is up and shows packets being sent and received:
ATM0 is up, line protocol is up
Hardware is MPC ATMSAR, address is bc16.6596.9b00 (bia bc16.6596.9b00)
MTU 1600 bytes, sub MTU 1600, BW 704 Kbit/sec, DLY 520 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5
4 maximum active VCs, 1024 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input 00:00:28, output 00:00:07, output hang never
Last clearing of "show interface" counters 6d23h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     23886 packets input, 1676964 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     56469 packets output, 4418592 bytes, 0 underruns
     0 output errors, 0 collisions, 6 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
Does anyone have any ideas on where the problem may be and what more I can do to troubleshoot and provide the relevant evidence to our ISP (assuming it is an ISP/BT issue though the fact the same router works ok with the exact same details etc would seem to indicate it must be their issue!)

Hi Jody,
thanks for the suggestions. Here's what I see from the ppp debugs (but I'm not sure how to interpret?)
Jan 6 14:50:22.838: pppoe_send_padi:
contiguous pak, size 74
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 FF FF
FF FF FF FF BC 16 65 96 9B 00 88 63 11 09 00 00
00 10 01 01 00 00 01 03 00 08 0C 00 00 01 00 00
04 A3 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 ...
Jan 6 14:50:22.878: PPPoE 0: I PADO R:0030.8810.000b L:bc16.6596.9b00 0/38 ATM0.1
contiguous pak, size 71
BC 16 65 96 9B 00 00 30 88 10 00 0B 88 63 11 07
00 00 00 33 01 03 00 08 0C 00 00 01 00 00 04 A3
01 02 00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73
2D 62 61 73 2D 42 32 32 36 45 34 37 30 39 45 30
31 34 5A 01 01 00 00
Jan 6 14:50:24.885: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:50:35.125: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:50:45.364: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:50:55.603: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:51:05.843: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:51:16.114: OUT PADR from PPPoE Session
contiguous pak, size 85
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
61 73 2D 42 32 32 36 45 ...
Jan 6 14:51:26.353: [0]PPPoE 0: O PADT R:0000.0000.0000 L:0000.0000.0000 0/38 ATM0.1
contiguous pak, size 74
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 00
00 00 00 00 00 00 00 00 00 00 88 63 11 A7 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 ...
Jan 6 14:51:46.576: pppoe_send_padi:
contiguous pak, size 74
00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 FF FF
FF FF FF FF BC 16 65 96 9B 00 88 63 11 09 00 00
00 10 01 01 00 00 01 03 00 08 0C 00 00 01 00 00
04 A3 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 ...
Jan 6 14:51:46.608: PPPoE 0: I PADO R:0030.8810.000b L:bc16.6596.9b00 0/38 ATM0.1
contiguous pak, size 71
BC 16 65 96 9B 00 00 30 88 10 00 0B 88 63 11 07
00 00 00 33 01 03 00 08 0C 00 00 01 00 00 04 A3
01 02 00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73
2D 62 61 73 2D 42 32 32 36 45 34 37 30 39 45 30
31 34 5A 01 01 00 00
Provider wouldn't have bumped us from ADSL to VDSL - but here's the output of show controller vdsl 0:
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'IFTN'
Chip Vendor Specific: 0x0000 0x71C8
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FCZ1111C08V C887VAG 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x71c8
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.992.1 (ADSL) Annex A
TC Mode: ATM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 1 8
Line Attenuation: 54.5 dB 31.5 dB
Signal Attenuation: 54.5 dB 0.0 dB
Noise Margin: 6.7 dB 11.0 dB
Attainable Rate: 2132 kbits/s 888 kbits/s
Actual Power: 16.7 dBm 12.7 dBm
Total FECC: 546 0
Total ES: 6 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 486 486
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
Full inits: 14
Failed full inits: 1
Short inits: 0
Failed short inits: 1
Firmware Source File Name (version)
VDSL user config flash:vdsl.bin-A2pv6C035d_d23j (10)
Modem FW Version: 110802_1752-4.02L.03.A2pv6C035d.d23j
Modem PHY Version: A2pv6C035d.d23j
Vendor Version:
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 1664 0 704
SRA Previous Speed: 0 0 0 0
Previous Speed: 0 1600 0 736
Total Cells: 0 2786872 0 0
User Cells: 0 68 0 0
Reed-Solomon EC: 0 546 0 0
CRC Errors: 0 9 0 0
Header Errors: 0 10 0 0
Interleave (ms): 0.00 8.00 0.00 8.00
Actual INP: 0.00 1.12 0.00 1.28
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
And here's the output from the ATM and dialer interfaces:
interface ATM0
no ip address
ip flow ingress
no atm ilmi-keepalive
end
interface ATM0.1 point-to-point
ip flow ingress
pvc 0/38
pppoe-client dial-pool-number 2
end
interface Dialer2
description OUTSIDE
ip address negotiated
ip access-group firewall in
ip mtu 1492
ip flow ingress
ip nat outside
ip inspect DEFAULT100 out
ip virtual-reassembly in
encapsulation ppp
dialer pool 2
dialer-group 2
ppp authentication chap callin
ppp chap hostname ###removed###
ppp chap password ###removed###
no cdp enable
crypto map dcvpn
end
As I say though, config-wise, everything should be correct - the same router works fine on another line (which should also confirm the authentication details are correct - at least in as far as it matches what the ISP have on their RADIUS)
Any further thoughts?

ADSL Interface problem

I have installed the Cisco 1721 with WIC-1ADSL and VPN module and configured to connect to the Japan network over VPMN from India.
WAN link is ADSL.(bridging mode)
It works fine,but suddenle I lose the CD in the ADSL interface card,and I lost the connectivity,if it works it works fine for say 4 to 5 days,If it lose the CD then I struggle to get the connectivity.When the CD is not detected that time if I replace the Cisco 1721 router with the ISP provided ADSL router then it get connected to the Internet.
This is not a permanent problem,it is a intermitent problem.
Could u please guide me?
Thanks and Regards,

Hello Gab,
your problem is indeed very annoying and common to xDSL backup solutions. Cisco has a 'new' feature called "object tracking" which is designed to address this issue, check this link:
Reliable Static Routing Backup Using Object Tracking
http://www.cisco.com/en/US/products/sw/iosswrel/ps5413/products_feature_guide09186a00801d862d.html
Basically, you track the object (ip address) on the internet via your primary link, if the primary link fails, the router will activate the backup link, effectively eliminating the dependency on the interface status...
HTH,
GP

2811 w/ WIC-1ADSL-I-DG PPPoA issue

Hello:
I have been trying to test our new office gear prior to move, specifically the DSL WIC card.
It seems I have all the config correct but I fail to negotiate link and I am not getting much info from a debug standpoint leading me to believe: -1- PPP isn't quite set up correctly -2- the WIC is possibly bad.
Would it be possible for someone to review my config since I can find nothing on the web that serves as a decent example of using this WIC card with Qwest?
DETAILS:
Info pulled from my old Actiontec modem for testing purposes:
VPI/VCI = 0/32
DSL Mode = MMODE
DSL Negotiated Mode = T1.413
Up/down = 7168/896
ATM QoS class = UBR
The connection is doing PPPoA, evidently it is using PAP per my ISP (qwest does the local loop, my own ISP the VC termination and routing)
Cisco 2811 and WIC setup:
interface ATM0/1/0
description QWEST DSL - circuit id:
no ip address
no ip mroute-cache
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
dsl enable-training-log
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
ppp authentication pap
ppp pap sent-username <username_goes_here> password 0 <passwd_goes_here>
Additionally, it would be helpful if you provided what all the 'Modem States' are. For example, Modem state = 0x8 is in many docs but you don't say anything about 0x3. Its helpful to know all the codes for Modem state if your going to recommend doing debugs of atm events for troubleshooting. Hence, the post to the forum. I can't get link and everything appears to be set up properly.
Thanks for the insight/answers.

No, I am afraid we don't do ADSL over ISDN. My boss ordered the equipment and I think the reseller wasn't too bright.
So would I be correct that I am going to have to have a WIC-1ADSL or a HWIC-1ADSL?
I see that this ADSL over ISDN card we have currently does support T1.413, but given I can't get link I am guessing that is only T1.413 when over ISDN so I have to use one of the other types of WICs listed above if this is over POTS.
If someone from Cisco or otherwise can confirm that would be great so I can go ahead and get the right card shipped to us ASAP.
Thanks for the assist,
-Jeff
Thanks for pointing that out. I suspected it might be the issue but have not ordered or touched many DSL WICs in my day, only the bigger chassis's that terminate the traffic on the provider end.

Cisco 1760 with shdsl

I have a cisco 1760 router with one adsl wic and one shdsl wic (wic 1 shdsl v3).The router has detected the adsl wic but not the shdsl.I am using the following software:c1700-y7-mz.123-4.XG5.bin.I have tried several ios and used feature navigator to find ios but neither works.Here is output of sh version
Can somedy help ?

Already replied in WAN forum, please do not open duplicate threads.

ADSL over Frame Relay

Hi all,
I have a Ascend DSLTNT in my Lab and they only support ADSL over frame relay and I dont have compatible modems. Is there any cisco ADSL WIC card which I can use in 2600 router for adsl or sdsl over frame relay. I will be grateful for your help.
Thanks in advance.
Regards
Meer

There is an ADSL WIC, please check below for details.
http://www.cisco.com/en/US/tech/tk175/tk15/technologies_q_and_a_item09186a0080093bff.shtml#a
Hope this helps.

Cisco 2620 Adsl WIC

Similar Messages

Maybe you are looking for