Cisco 6500 --ACL entries showing incorrect order.

Hi guys,
I need your suggestion on my following issue:
I have configure the ACL entries on my cisco 6500 series box but I see the ACL entries showing incorrect order when I check for the same.
Eg:
Europebox#show access-list 50
10 permit 192.50.20.2 (10 matches)
15 permit 192.52.0.134 (98 matches)
75 permit 198.29.232.23 (38 matches)
80 permit 10.96.127.14
90 permit 192.22.2.10
40 permit 192.22.0.76
anyhelp would be appriciated
regards
neha

Hi neha,
This is the expected behaviour that you see for the standard access-lists.
Regards
Inayath

Similar Messages

Cisco 6500 shows less traffic for NetFlow export

I am using a Thrid party NetFlow tool, Enabled NetFlow on the Cisco 6500 as per recommendations and getting only half amout of traffic passing thorugh the interfaces. I have verified with 3 different NetFlow based tools, everything showing the same value. Is there any bug in my Cisco 6500. Any one faced this issue. Attached the output of (show run, show version)
Cheers

Hi Jake,
I have already investigated this, the exporting interval and aging time for flows are set to lower active timeout. Is there any way to see all the flows are beeing captured and exported both on MSFC and PFC.
Cheers

Cisco 6500 with sup720 booting to rommon

Please how can I solve this problem. This cisco 6500 boots to rommon mode, I can't see any error showing why its booting to rommon.

Here is the boot process:
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower memory for cache initialization
Clearing bss
Clearing autoboot state machine
melody_present_reg: 1st read w/ 0x5555
melody_present_reg: 2nd read w/ 0xaaaa, reversed: 0x5555
Bootdisk adapter is detected, enabling bootdisk access...
Reprogramming CS1 w/ Melody value...
Reading monitor variables from NVRAM
Reset reason for CPU board 0xffff , BaseBoard 0x281ffff, display 0x20000System Reset by Software.
Enabling interrupts
Initializing TLB
Initializing cache
Initializing required TLB entries
MOBILE dimm - rev 0.15
Initializing main memory
Sizing NVRAM
Initializing PCMCIA controller
Initializing USB2.0 controller
Exiting init
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
Autoboot: failed, BOOT string is empty
Autoboot executing command: "boot "
Initializing ATA monitor library...
string is bootdisk:s72033-ipbasek9-mz.122-33.SXJ2.bin
Loading image, please wait ...
Initializing ATA monitor library...
Stack pointer       : 0x8FFFFF80
monstack            : 0x800FFFC0
monra               : 0xBFC26EC4
edata : 0x80108580
magic : 0xFEEDFACE
memsize             : 0x10000000
uncomp_size         : 0x05090C00
comp_size           : 0x05090C00
comp_checksum       : 0x98ECBE18
uncomp_checksum     : 0x98ECBE18
CZIP_MEM_BASE       : 0x80000000
_end       : 0x8010BA00
Self extracting the image...
IOS compressed src copy is     : 0x80108594
czip + IOS tar size is :0x00E01FA8
czip + IOS Tar image is now :0x80108794
cptr is now :0x8010BB00
IOS compressed dest copy is     : 0x8010BB00
[OK]
image_entry :0x80100000
image_entry :0x80100000
__start : 0x80100000
tar_avail_size is now :0x0428EA00
Tar image address is             : 0x80F0DB00
tar_size is           : 0x0428E600
cpu type                   : 0x00000019
uncomp_size                : 0x05090C00
monstack                   : 0x800FFFC0
image_info.entry_point   = 0x80100000
image_info.section_count = 0x00000005
image_info.monstack      = 0x800FFFC0
image_info.monra         = 0xBFC26EC4
image_info.param0        = 0x00000002
image_info.param1        = 0x00000000
image_info.param2        = 0x800066A8
image_info.param3        = 0x80100000
image_info.reg_k0        = 0x80F0DB00
image_info.reg_k1        = 0x0428E600
Section Index = 0x00000000
    source    = 0x8010BC1C
    dest      = 0x80100000
    bytes     = 0x00010000
Section Index = 0x00000001
    source    = 0x8011BC1C
    dest      = 0x80110000
    bytes     = 0x00000720
Section Index = 0x00000002
    source    = 0x8011C33C
    dest      = 0x80110720
    bytes     = 0x00000020
Section Index = 0x00000003
    source    = 0x8011C35C
    dest      = 0x80110740
    bytes     = 0x00DF1730
Section Index = 0x00000004
    source    = 0x80F0DA8C
    dest      = 0x80F01E70
    bytes     = 0x00000000
reg_v0: 0x00000000
reg_k0: 0x80F0DB00
reg_k1: 0x0428E600
tar_start: 0x00000000
tar_size: 0x00000000
Tar image address is             : 0x80F0DB00
tar size is :0x00B6130E
Tar magic : ustar Tar filename : C2LC memsize             : 0x10000000
Tar gid         : 035231Tar uncomp_size         : 0x00B6130E
Tar mtime         : 11672344432 Tar username          : ccaiTar comp_checksum       : 0x0000125F
Tar group name    : buildTar prefix    : tar_size in czip         : 0x0428E600
Stack pointer       : 0x8FFFFF80
monstack            : 0x800FFFC0
monra               : 0xBFC26EC4
edata : 0x80110740
magic : 0xFEEDFACE
memsize             : 0x10000000
uncomp_size         : 0x02B3E7F0
comp_size           : 0x00DF171C
comp_checksum       : 0xE917F280
uncomp_checksum     : 0xD094D890
Compressed IOS src copy is     : 0x80110754
tar_dest is :0x8BD69200
tar_size is :0x0428E600
Compressed IOS dest copy is     : 0x8AF77AE4
Tar src before IOS decompression is     : 0x80F0DB00
Tar dest before IOS decompression is     : 0x8BD69200
compressed IOS src is     : 0x8AF77AE4
IOS uncompressed dest copy is     : 0x8013C160
Self decompressing the image : ############################################################################################################################################################################################################################## [OK]
e_shoff :
0x02B3E660
e_flags : 0x10001001
e_phnum :
0x00000001
Source elf_hdr->e_shnum = 0x0000000A
Setting up to copy ELF section 0x00000001
to image_info section 0x00000000
sh_name = 0x0000000B
sh_type = 0x00000001
sh_flags = 0x00000007
sh_addr = 0x80100000
sh_offset = 0x00000060
sh_size = 0x02640000
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000020
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000002
to image_info section 0x00000001
sh_name = 0x00000011
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x82740000
sh_offset = 0x02640060
sh_size = 0x00373440
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000008
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000003
to image_info section 0x00000002
sh_name = 0x00000017
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x82AB3440
sh_offset = 0x029B34A0
sh_size = 0x0003EEE4
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000004
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000004
to image_info section 0x00000003
sh_name = 0x00000024
sh_type = 0x00000001
sh_flags = 0x10000003
sh_addr = 0x82AF2324
sh_offset = 0x029F2384
sh_size = 0x0000423C
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000010
sh_entsize = 0x00000000
sh_type = 0x00000008
sh_flags = 0x10000003
sh_addr = 0x82AF6560
sh_offset = 0x029F65C0
sh_size = 0x00000940
sh_type = 0x00000008
sh_flags = 0x00000003
sh_addr = 0x82AF6EA0
sh_offset = 0x029F65C0
sh_size = 0x021FE100
tar file start = 0x84D02F50
cpu type                   : 0x00000019
uncomp_size                : 0x02B3E7F0
monstack                   : 0x800FFFC0
image_info.entry_point   = 0x80100000
image_info.section_count = 0x00000005
image_info.monstack      = 0x800FFFC0
image_info.monra         = 0xBFC26EC4
image_info.param0        = 0x00000002
image_info.param1        = 0x00000000
image_info.param2        = 0x800066A8
image_info.param3        = 0x80100000
image_info.reg_k0        = 0x84D02F50
image_info.reg_k1        = 0x0428E600
Section Index = 0x00000000
    source    = 0x8013C1C0
    dest      = 0x80100000
    bytes     = 0x02640000
Section Index = 0x00000001
    source    = 0x8277C1C0
    dest      = 0x8274CFB0
    bytes     = 0x00373440
Section Index = 0x00000002
    source    = 0x82AEF600
    dest      = 0x82AC03F0
    bytes     = 0x0003EEE4
Section Index = 0x00000003
    source    = 0x82B2E4E4
    dest      = 0x82AFF2D4
    bytes     = 0x0000423C
Section Index = 0x00000004
    source    = 0x8BD69200
    dest      = 0x84D02F50
    bytes     = 0x0428E600
data_size in czip         : 0x00001000
bss end of IOS is         : 0x84D01F50
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, s72033_sp Software (s72033_sp-IPBASEK9-M), Version 12.2(33)SXJ2, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 15-Dec-11 01:29 by prod_rel_team
Image text-base: 0x4010132C, data-base: 0x4274CFB0
Active crashed three times, disabling auto-boot and dropping to rommon
Firmware compiled 15-Nov-11 14:23 by integ Build [100]
*Jan 1 02:27:12.643: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch
*Jan 1 02:27:13.459: %PFREDUN-4-SUP_FORCE_TO_ROMMON: Supervisor forced to rommon with reason: Active crashed three times in a row
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
rommon 1 >

QoS: Multiple acl entries cannot be used in match-any in class Match_XY

Hello All,
I'm getting below error while trying to add the two extended ACL in the class-map for classifying the traffic. Is there any way I can add two extenteded ACL in the same class-map for classifying the traffic.
Error log: "QoS: Multiple acl entries cannot be used in match-any in class Tag_AF13"
device details: cisco WS-C6506-E with Supervisor Engine 2T
IOS version -s2t54-adventerprisek9-mz.SPA.150-1.SY1.bin
R1(config)#class-map match-any Tag_AF13
#match access-group name XX
#match access-group name XY
QoS: Multiple acl entries cannot be used in match-any in class Tag_AF13
Regards,
Thiyagu

Hi Rajan,
Thats because of the logic used for ACl operations, as per your config you are class-map match-any. The match any argument says that the class map must match either of the two arguments supplied.So lets take a look at how the sequence of operations of how this will be interpreted by your class map.
1> Any particular packet will be first matched against the first ACL "XX".
2> Suppose there are 10 entries there if it matches any of those entries the appropriate action will be talen.
3> If none of those entried match the packet there will be an implicit deny at the end of the ACL( default behaviour of ACL's)
4> In that case the packet will match the implicit deny and will get dropped.
5> The packet will under no circumstances go to the next ACL "XY"
Thats the reason multiple ACL's aren't allowed by the IOS.
You can try to collate both ACL's and put them in just one ACL that should work well. If you need help please pots both the ACL's.
Please do let me know if you have any further questions
HTH
Regards
Umesh

Some albums on my iPod have their songs in incorrect order

I guess I’m just old school. I like to listen to my music in the order that it appears on the album. Almost all of the albums have the songs in the correct order, but few do not. In particular, Today was listening to American Idiot (Green Day), what should be the third song has been placed way at the 8th position. In fact the song order for this album as played on my iPod is 1, 2, 4, 5, 7, 9, 11, 3, 6, 8, 10,12, 13.
I have verified that I have the latest iTunes and iPod firmware. I have my iTunes set to keep my music library in sync on my iPod (“Manually Manage music and videos is NOT checked) .
Here is a partial list of things I have already tried
• I have made sure that the music is sorted first by Artist, then by Album, then by Track number in iTunes.
• I have verified that the order is correct in my iTunes music library and the music library’s shadow in the iPod within iTunes
• I have done the 5 R’s
• I have switched to Manually Manage, deleted the offending albums, synced, re-added the albums, WATCHED THE SONGS LOAD IN THE CORRECT ORDER, just to find that they are still listed in an incorrect order when I look at them in my iPod.
Someone please help me and tell me how to fix this.
PC Windows XP Pro

The Cloud by the song indicates that is is an iTunes purchase but it is not downloaded on the iPod. If you only want download iTunes purchases to show in the Music app go to Settings>itunes and pp Store and turn off Show aLL.

Incorrect "Ordered" quantity in the item master data

Hello Experts,
I have a situation where there are two items we have found that show the incorrect ordered quantity in the item master data. This is in fact the ordered column and the items are not production items. One of the items is showing a negative quantity and the other is showing 50,000 LBs less than it should given the one open production order with NO GRPO documents linked. Please advise ASAP..
Thank you,
Taylor

Hi,
You need to check the detect query and the scenarios in the Note No. : 999124.
If the detect query of the Note returns result, you need to log a support ticket to get the database investigated.
Kind Regards,
Jitin
SAP Business One Forum Team

Report Viewer shows incorrect data when viewing pages from last to first

Post Author: Fmorales
CA Forum: .NET
Hello.
I've made a huge report with Crystal Reports for Visual Studio 2005, and sometimes the Report Viewer show data with errors.
If I see all pages of my report in order, 1 first, then 2nd, 3, 4... until the last one.... The report is always correct.
If I see all pages in reverse order, 1 first (shown by default), then last one, then last one-1.... until 2nd.. All years show incorrect, except first one...
In an outer section, for every year, there is a final row which shows summarize calculated data. The error consists in that every value of the row is 0.
It seems that Crystal Report calculates while showing, that's good.. but... Why does it ignore the data before when I see directly the last page?? It forces me to see all pages one by one in ascendant order to ensure data is correct.. I must fix that error.
The way I calculate data in the problematic summarize row is a bit complicated, but I'll try... Let's focus in one only column (the other ones are similar). The summarize value is a formula which simply show a global value :
WhilePrintingRecords;
CurrencyVar margenActual;
which is being increasing or decreasing along the group:
WhilePrintingRecords;
CurrencyVar actual:=actual+CurrentFieldValue;
if {PresupPeriodifMesesAux_DS.TIPO} = 'PAGOS' then CurrencyVar margenActual:=margenActual-CurrentFieldValueelse CurrencyVar margenActual:=margenActual+CurrentFieldValue;
DefaultAttribute
It is placed in the backgrond property of a CrossTab cell in a hidden pre-section... Well.. I know it's a bit complicated, but I have to do that way because it was the only trick I found to make a summarize file before printing data summarized (that's why the line "CurrencyVar actual:=actual+CurrentFieldValue;" appeared in formula). So I also wanted to use this formula to acummulate "margenActual".
In the inner section I reset the actual value (this value always go fine):
WhilePrintingRecords;
CurrencyVar actual:=0;
Before end of year I reset the margenActual value:
WhilePrintingRecords;
CurrencyVar margenActual:=0;
I've tried multiple combinations (using WhileReadingRecords instead WhilePrintingRecords) but data is incorrect or I cannot get rid of visualization page's problem....
Any idea?
Thanks a lot

quote:
Originally posted by:
ntsiii
If you were previously using <mxXML> you WERE using
e4x.
So remove that tag, create an instance variable of the same
name, typed as xml, and in your result handler, do as VarioPegged
suggests, though I would cast/convert to xml first:
companies = XML(event.result);
trace(companies.toXMLString()); to look at your xml
var xlCompanies:XMLList = xmlCompanies..company; //all such
expressions return XMLList, never XML
trace(xmlCompanies.length()); //
Tracy
Ok so the ID of the mxXML was being interpreted as an E4X
variable at compile time?
I tried changing the name of the ID of the HTTPService call
from "marketData" to "MDATA" and assigning the variable marketData
to the result of the HTTPService query, which if I understand you
correctly should basically make everything work as it was before,
but it seems to be a problem.
when I try to run it puts an exclamation point on this line
<toolbox:TreeMap id="treeMap" width="1200" height="800"
dataProvider="{marketData}"
labelField="@cname" weightField="@amount"
colorFunction="{itemToColor}"
toolTipFunction="{itemToToolTip}"/>
That code refers to a SWC file. Apparently it wants
marketData to be a data provider. If I change the dataProvider
reference above to "MDATA" (the ID of the HTTPService) the App
compiles, but I get two errors at runtime:
TypeError: Error #1009: Cannot access a property or method of
a null object reference.
ReferenceError: Error #1081: Property @age1 not found on
mx.rpc.http.mxml.HTTPService and there is no default value.
What should I change this reference to? It won't compile if I
use the variable I made for the e4x results and it is reading
gibberish if I have it read directly from the
HTTPService....?

0weekday1 is showing incorrect values

Hi,
After the upgrade it has been noticed that the Time characteristic 0weekday1 is showing incorrect text mapping in Bex Reports reports.
After analysis and Investigation I found that
In master data it is maintained as follows which is correct
1 - Sunday
2 - Monday
3 - Tuesday
4 - Wednesday
5 - Thursday
6 - Friday
7 - Saturday
But In the multiprovider, when I do F4 on the filed 0weekday1 it is showing the following values
1 - Monday
2 - Tuesday
3 - Wednesday
4 - Thursday
5 - Friday
6 - Saturday
7 - Sunday.
In RSRV it is showing inconsistencies but when I tried to do the correction it is failing.
I have done the info Object repair for 0weekday1 in RSD1. but still the values have not changed.
Please suggest resolutions to this !!!
Thanks,
Shantanu.

Hi,
When I see the master data it is maintained properly as stated above.
But, when I checked the Master Data Read class, it is found that the data is coming from T246 table which is SAP maintained table. And the entries made in T246 table are the one which are incorrectly mapped.
So, my questions are:
1. Can we change the values directly in T246 table.
2. What other programs/objects, etc will be impacted.
3. Do we have something as "Where used list" for the Tables.
Thanks,
Shantanu.

Incorrect Order Multiple in Webshop

Hi experts,
Please help. We have a problem in our webshop wherein it is showing an incorrect order multiple of 1, supposedly it is 3. When we check our backend which is ECC, it is showing the correct delivery unit which is 3. Did we miss to check something? Thanks in advance.
Regards,
Mike

Hi,
Check whether the warehouse assigned is Nettable. If sales order to be considered in MRP, mark Consume Forecast(if you have defined a forecast) in SO, also in General Setting, Inventory Tab mark Consume Forecast
Regards
ShriX.

Report to correct FD33 report is showing incorrect values ??

Hi Guys,
Will appreciate your help on below issue.
The "RVKRED88 - Reorganization of SD credit data after updating errors" report is showing incorrect values.
It is specially observed for invoice correction requests that are credit blocked.
The doc flow is like Order (say value 1000 $), delivery, shipment, Picking, GI, billing, accounting all cleared/complete.
The invoice corrrection req (say value -ve 50$) was then created with reference to the billing doc.
The RVKRED88 report shws the original order as open and also shows an open delivery value of 1000$ + 50$= 1050$.
Is this behaviour correct? If not what might be the cause of this? and how to correct it?
Regards,
Naminator
Edited by: Naminator on Jul 7, 2009 6:22 PM

I am not sure, how come you are getting correct numbers for UK plant if BX is not loaded. You can get numbers correctly only in one situation which is your initial stock at that plant was ZERO, which is practically not possible.
You said you are loading for Denmark only.
Was the BF init done only for UK?
How come you are loading BF Delta for UK only?
Did you check properly that BX is not loaded into production by changing the date range. Make sure you put the lowest date range in the from field. I would put 01/01/1000
As you said ISS is coming right because those are movements and they dont have to do anything with initial stock, but initial stock and movements affec your Total Stock Key Figure.
- Danny

CP-7821 showing incorrect timeing

Hi,
We are using cisco CP-7821 IP phones but some IP phones are showing incorrect time. Need assistence for fix this issue.

Hi Aman,
As per your suggestion, I checked the firmware version of IP phones and i found that some IP phones which are showing correct timing having firmware version
sip78xx.10-1-1SR1-4.loads
And some which are showing incorrect timing having firmware version
sip78xx.10-2-1-12SR1-4.loads
> Time zone is correct because only 4 out of 30 showing incorrect time.
Neeraj

Permissions are incorrectly ordered Error

I was looking to change some permissions on out AD when I right clck on the root in our domain hit properties then the security tab I get a Pop up
The permissions on THISMOMAON.COM are incorrectly ordered, which may cause some entries to be innefective.
Tor order the permissions correctly click reorder.
To leave the permissions unchanged (the view will be read only) Click cancel.
If this were just a folder or OU I'd just hit reorder but since I don't know exactly what it does it makes me nervous hitting reorder on the root. But since I don't all the settings are grayed out as in read only. Does anyone know what this means?
Jason

I was looking to change some permissions on out AD when I right clck on the root in our domain hit properties then the security tab I get a Pop up
The permissions on THISMOMAON.COM are incorrectly ordered, which may cause some entries to be innefective.
Tor order the permissions correctly click reorder.
To leave the permissions unchanged (the view will be read only) Click cancel.
If this were just a folder or OU I'd just hit reorder but since I don't know exactly what it does it makes me nervous hitting reorder on the root. But since I don't all the settings are grayed out as in read only. Does anyone know what this means?
Jason
Take a system state backup of at least one DC with global catalog. Once done, run the reorder action outside of Business hours. If you noticed that something went wrong then you can do an authoritative restore.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

IP TCP intercept cisco 6500

Hi,
does anyone has experience with ip tcp intercept configuration on cisco 6500 for protecting network against TCP SYN flooding.
Which mode is recommended to configure (intercept or watch) and how can affect CPU on cisco 6500?
Any infos regarding that would be much appreciated.
Thank you
Salja

Hey Salja,
In Sup720 for TCP Intercept the support is as follows:
Watch mode: Initial TCP packets (SYN, SYN-ACK and ACK of SYN-ACK) and terminating TCP packets (FIN, RST) of a TCP flow is sent to RP for processing in SW. All other TCP packets of the flow are handled in HW using netflow (if TCP packets come in before the netflow entry is created it will get punted to SW). Note that the rate of netflow entry creation is limited and if new TCP connections come in at a rate faster than the rate at which netflow entries can be created in HW there will be large number of packets hitting the CPU.
Intercept Mode: For Intercept mode without timeout the behavior is similar to Watch mode mentioned above. Intercept mode with timeout all packets of a TCP flow is handled in SW by the RP.
So its not advised to use TCP intercept on 6500 as it may degrade box performance. I would suggest using firewall for this feature.
HTH.
Regards,
RS.

Cisco 6500 power supply and module (hot-swappable?)

Hi everyone!
We have currently a Cisco 6500 with 2 power supply of 3000w. We want to replace these PS for 2 new ones, which have higher wattage: 6000w.
Can we replace them without needing to turn the 6500 off?. I mean, What happens if we insert a 6000w PS and the switch is working with one 3000w PS?
Is it possible to do this replacement "on hot"?
And second, we also have a ws-x6708-10g-3c module. Can we insert this module "on hot"? Without needing to turn the Catalyst 6500 off?
Thanks a lot! and looking forward to an answer.

Depends on your setup the table should be able to help:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/pwr_envr.html#wp1020384
Configuration Change
Effect
Redundant to nonredundant
•System log and syslog messages are generated.
•System power is increased to the combined power capability of both power supplies.
•Modules marked power-deny in the show power oper state field are brought up if there is sufficient power.
Nonredundant to redundant (both power supplies must be of equal wattage)
•System log and syslog messages are generated.
•System power is decreased to the power capability of one supply.
•If there is not enough power for all previously powered-up modules, some modules are powered down and marked as power-deny in theshow power oper state field.
Equal wattage power supply is inserted with redundancy enabled
•System log and syslog messages are generated.
•System power equals the power capability of one supply.
•No change in module status because the power capability is unchanged.
Equal wattage power supply is inserted with redundancy disabled
•System log and syslog messages are generated.
•System power is increased to the combined power capability of both power supplies.
•Modules marked power-deny in the show power oper state field are brought up if there is sufficient power.
Higher or lower wattage power supply is inserted with redundancy enabled
•System log and syslog messages are generated.
•The system does not allow you to operate a power supply of different wattage even if the wattage is higher than the installed supply. The inserted supply shuts down.
Higher or lower wattage power supply is inserted with redundancy disabled
•System log and syslog messages are generated.
•System power is increased to the combined power capability of both power supplies.
•Modules marked power-deny in the show power oper state field are brought up if there is sufficient power.
Power supply is removed with redundancy enabled
•System log and syslog messages are generated.
•No change in module status because the power capability is unchanged.
Power supply is removed with redundancy disabled
•System log and syslog messages are generated.
•System power is decreased to the power capability of one supply.
•If there is not enough power for all previously powered-up modules, some modules are powered down and marked as power-deny in theshow power oper state field.
System is booted with power supplies of different wattage installed and redundancy enabled
•System log and syslog messages are generated.
•The system does not allow you to have power supplies of different wattage installed in a redundant configuration. The lower wattage supply shuts down.
System is booted with power supplies of equal or different wattage installed and redundancy disabled
•System log and syslog messages are generated.
•System power equals the combined power capability of both power supplies.
•The system powers up as many modules as the combined capacity allows.

CISCO 6500 VS HUAWEI S9700

I NEED COMPARISON BETWEEN CISCO VS-C6509E-SUP2T vs S9700 , becuse i have a very compettive offer from huawei , really i need to onvince my customer that cisco 6500 is better than huawei 9700 in performance

where is the link that shows theat information
Something that "big" and launching in the next few months will not bet published. You'll need to talk to a Cisco R&S SE to get more information.

Cisco 6500 --ACL entries showing incorrect order.

Similar Messages

Maybe you are looking for