CISCO Prime Infrastructure 2.0 Link UP DOWN ALERT
Hi,
I want to monitor core switch link up down status and ignore all the access switch link up down. How do I do that? My core switch is nexus 7009 and my access switch is 2960s.
I have tried configuring port group for core switch and access switch and only deploy interface health template to my core switch port group but I still receiving link down alert from my access switchport even without deploying the template to my access switch.
Am I doing it the right way? Help please. Thank you.
Hi Rafael,
Here is the config:
snmp-server community cxxx_ro RO SNMP_ACL
snmp-server community cxxx_rw RW SNMP_ACL
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps transceiver all
snmp-server enable traps tty
snmp-server enable traps cluster
snmp-server enable traps entity
snmp-server enable traps cpu threshold
snmp-server enable traps rep
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps flash insertion removal
snmp-server enable traps port-security
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps power-ethernet group 1
snmp-server enable traps power-ethernet police
snmp-server enable traps fru-ctrl
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps energywise
snmp-server enable traps rtr
snmp-server enable traps vstack
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vlan-membership
snmp-server enable traps errdisable
snmp-server host 10.189.x.x version 2c cxxx_ro
snmp-server host 10.189.x.x version 2c cxxx_ro
and this is the switch interface
interface FastEthernet0/1
switchport access vlan 28
switchport mode access
srr-queue bandwidth share 1 30 35 5
priority-queue out
mls qos trust cos
no snmp trap link-status
auto qos trust
spanning-tree portfast
and yes I configured that on all access port in all switches.
Regards,
Syafiq
Similar Messages
-
Cisco Prime Infrastructure 2.1 not send email alert when link down
Hello everyone
I use PI to monitor 1 switch and 1 firewall . When a link up/down on switch , PI immediately sends an email alert .
But when a link up/down on FW , PI not send any email alert . PI knows link up/down on a FW is a critical alarm ( it's show up on "Alarm Browser") , but not send email.
I enable all SNMP trap on FW , i tested that event on SolarWinds and it immediately sends an email alert . So there is no problem about FW configCauses of Errdisable
This feature was first implemented to handle special collision situations in which the switch detected excessive or late collisions on a port. Excessive collisions occur when a frame is dropped because the switch encounters 16 collisions in a row. Late collisions occur after every device on the wire should have recognized that the wire was in use. Possible causes of these types of errors include:
A cable that is out of specification (either too long, the wrong type, or defective)
A bad network interface card (NIC) card (with physical problems or driver problems)
A port duplex misconfiguration
A port duplex misconfiguration is a common cause of the errors because of failures to negotiate the speed and duplex properly between two directly connected devices (for example, a NIC that connects to a switch). Only half-duplex connections should ever have collisions in a LAN. Because of the carrier sense multiple access (CSMA) nature of Ethernet, collisions are normal for half duplex, as long as the collisions do not exceed a small percentage of traffic.
There are various reasons for the interface to go into errdisable. The reason can be:
Duplex mismatch
Port channel misconfiguration
BPDU guard violation
UniDirectional Link Detection (UDLD) condition
Late-collision detection
Link-flap detection
Security violation
Port Aggregation Protocol (PAgP) flap
Layer 2 Tunneling Protocol (L2TP) guard
DHCP snooping rate-limit
Incorrect GBIC / Small Form-Factor Pluggable (SFP) module or cable
Address Resolution Protocol (ARP) inspection
Inline power
Note: Error-disable detection is enabled for all of these reasons by default. In order to disable error-disable detection, use the no errdisable detect cause command. The show errdisable detect command displays the error-disable detection status. -
Cisco Prime infrastructure Change severity Switches and hubs - link down alarm
Hi, I want to change the severity of the link down alarm in the Cisco Prime Infrastructure 1.3, but in the menu Administration -> System Settings -> Severity Configuration i can not find the alarm. Some body knows where is it? o where i can change the severity of that alarm?
Thanks in advanced.Hi Rollin and Daniel,
the first test i did changing the severity was with a new installation, with no devices added and it worked, when i did it in a Prime infrastructure with devices added it didn´t work, well, for this Prime with devices i upgraded it with the patch for 1.3 version and now it works too, the alarms is ok as the alarm severity, this is the link for the patch:
http://software.cisco.com/download/release.html?mdfid=284652876&flowid=38562&softwareid=284272933&release=1.3.0&relind=AVAILABLE&rellifecycle=&reltype=all
i hope this helps,
Regards,
Milton Tizoc. -
Cisco Prime Infrastructure 2.0 Alarms (switch port down)
We have a cisco Prime Infrastructure 2.0 managing switches, routers and AP.
By default, when a port of a switch goes down, the cisco Prime Infrastructre generates a Critical Alarm for that. (this is a problem, because every phone of laptop disconnection will generate a critical alarm for me)
I found out that if we go to Administration --> Alarm Severity --> Link down, I can change the Alarm from Critical to another type of alarm.(ex: warning)
The problem is that I want to keep the Critical Alarm for my Uplinks ports and for some important switch ports, and I would like to make the alarm as warning for the normal user ports.
I know that I can create Port Groupping and add ports to each group and apply monitoring templates on those groups. But This couldn't Help me solving my alarm problem.
So I just need to know how to manage the alarms severity for each group of ports.
Thank youHi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work? -
Cisco Prime Infrastructure MESH LINK ISSUE
Hi,
a Customer of us has a trouble with cisco Prime Infrastructure 1.2.0.12 and AP mesh link.
There is an huge database ( i suppose the issue can be here ) and when we display some map ( each floor has about 6 RAP and 24 MAP ) we cannot see the MESH information and link draw.
The only way to dipley them is to disable "refresh from network": this way I'm able to show these link..... until a click before.
What i noticied when all was working fine, after i click to some floor:
1) the software started to show the map with normal color and no mesh info displayed ( just ap and coverage cloud )
2) after few time ( less than 1 second ) the map was becoming a little bit lighter and the mesh info was merged to the map
We are missini the second step
Anyone had the same issue ?
best regards
Luigi
PS: I opened a case with WCS version 6.0 ( same issue ) but, after some months, no risult. The last version working fine was WCS 5.2Just to add some more informations:
- disabling "refreshj from network" ( building properties ) the link and mesh info are showed
- while I'm on a floor, after some refresh, i loose the mesh link draw and, if i click on an AP, i loose also mesh info in the popup. It' s like, after some refresh, the AP are no more recognized as Mesh ( !?!? )
regards
Luigi -
Cisco Prime Infrastructure 2.0 import image via WAN link failed.
Cisco Prime Infrastructure 2.0 behind NAT that can copy image on device to Cisco Prime infra but can not deploy from Cisco Prime Infra import image from device. How to solve problem,please ?
Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location. -
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Including Interface Description in Cisco PRime Infrastructure Alarm Message
Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advanceHi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards, -
Cisco Prime Infrastructure 2.0 not showing alerts from switch
Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advanceHi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work? -
When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?
We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
ChristianPI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks -
Cisco Prime Infrastructure 2.0 and Cisco ASA
Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location. -
Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1
Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors ***** -
Cisco Prime Infrastructure 1.3 to 2.1
I have a Cisco Prime Infrastructure version 1.3 virtual appliance and we have a new Prime Infrastructure version 2.1 virtual appliance set up. I would like to get the wireless information put into the new server. This includes the WLC and APs and then the campus maps and the location of each AP on the map Im not sure if the heat mapping is a feature of Prime or if I have to set that up too. But I would like the heat maps.
What would be the easiest way todo this?Are you logged in with a cisco.com (CCO ) userid? I just checked it and it works fine for me.
You can navigate down to it via:
HOME
SUPPORT
PRODUCT SUPPORT
CLOUD AND SYSTEMS MANAGEMENT
CISCO PRIME INFRASTRUCTURE
INSTALL AND UPGRADE
INSTALL AND UPGRADE GUIDESCisco Prime Infrastructure 2.1 Quick Start Guide -
Monitoring ASA in Cisco Prime infrastructure 2.2
Hi everybody. I have some issue with cisco Prime Infrastructure 2.2. We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4. I added ASA to Cisco PI but see only basic component like my device can reachable via and read via snmp. But cannot see CPU, RAM, Device ENV like Temperature, l2l vpn connection, Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20. I need fully monitor ASA and See logs and trap for my device:
CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN Status.
1 Cisco Prime infrastructure can full support ASA for monitoring and logging.. IF YES how can i configure that features in Cisco PI 2.2 for ASA
2 IF not which product Can full support that features for full monitoring and logging ASA devices
I have a little deadline for finishing
thanks everybody beforeI've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches. -
Cisco Prime Infrastructure 1.2 licensing
I have a customer that is running CiscoWorks 3.2 and they also have NCS 1.1 (upgraded from WCS 7.0). They have found that it costs way more to upgrade CiscoWorks to Cisco Prime Infrastructure than it would be to just buy licenses after they finish upgrading NCS to Cisco Prime 1.2.
The main question about Cisco Prime 1.2 is how the licensing works, we need to know if the licensing will work the same as it did for CiscoWorks where they only needed one license for a full stack of switches. They believe that Prime 1.2 will require a license for each switch in the stack, which will cause them to buy several more licenses than what they feel they can afford.
If anyone knows how the licensing works, it would be appreciated.
Thanks.Have you gone through the below link
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide_c07-714720.html
Maybe you are looking for
-
Issues with external hard drive
hello, i recently purchased a seagate external hard drive 2TB. i am trying to copy videos onto the external hard drive from my macbook( mac osx version 10.6.3 but the files wont copy. i checked the details of the external hard drive, formatted for wi
-
Handling Material Variance for 3rd Part PO with No Invoice
How can material variances be handled for 3rd party purchase orders with no invoice?
-
After getting my dreadful speed sorted with the help of the mods I have gone and trashed it by changing routers for a BT business hub! My speed was almost 2.5 now its only 1.2. I quickly swapped back to my old router but its made no difference, here
-
My Mac is running Yosemite 10.1.1 and was working fine until recently. Now it does a hard install overtime I turn it on. Any suggestions?
-
Use only sales unit for a material in a sales order
Hi experts, Sorry in advance if my question has already been asked before. I looked for an answer in forums but I can't find it. One of my colleague told me about a customizing point which I can't find. When creating a sales order, for some materials