Cisco SG300 VLAN rate-limit
I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. Does anyone have an idea for configure vlan rate-limiting on SG300? And please describe CIR & CBS for me. Thanks.
http://www.cisco.com/en/US/partner/products/ps10898/prod_command_reference_list.html
Cisco Small Business 300 Series Managed Switches Command Line Interface Guide Release 1.3
Select CIR and CBS according to your design. You can use a larger CBS when performance is not ideal.
49.23 rate-limit (VLAN)
Use the Layer 2 rate-limit (VLAN) Global Configuration mode command to limit the
incoming traffic rate for a VLAN. Use the no form of this command to disable the
rate limit.
Syntax
rate-limit vlan-id committed-rate committed-burst
no rate-limit vlan
Parameters
• vlan-id—Specifies the VLAN ID.
• committed-rate—Specifies the average traffic rate (CIR) in kbits per second
(kbps). (Range: 3-57982058)
• committed-burst—Specifies the maximum burst size (CBS) in bytes.
(Range: 3000-19173960)
Default Configuration
Rate limiting is disabled.
Committed-burst-bytes is 128K.
Command Mode
Global Configuration mode
User Guidelines
Traffic policing in a policy map takes precedence over VLAN rate limiting. If a
packet is subject to traffic policing in a policy map and is associated with a VLAN
that is rate limited, the packet is counted only in the traffic policing of the policy
map.
This command does not work in Layer 3 mode. It does not work in conjunction with
IP Source Guard.
Example
The following example limits the rate on VLAN 11 to 150000 kbps or the normal
burst size to 9600 bytes.
switchxxxxxx(config)# rate-limit 11 150000 9600
Similar Messages
-
High cpu - Rate-limit cisco 6500
Hello,
my device is cisco 6509.
Explanation of the case:
Received to interface vlan (L3) 600M traffic (configured with Rate limit - 50 M).
Result :
1. 100 % cpu
2. the traffic was limited to 50M
How can I prevent High Cpu in this situation ?
Thanks.I would suggest opening a case, or asking in a different forum. This form is for discussion about existing bugs for which a bugid has been identified.
-
Hello friends,
I have a problem; now i'm changing the router that have at work of Cisco 3925 to Cisco ISR 4451X but in the new router i can't put the command that have in my old router:
rate-limit input access-group 110 16384000 3072000 6144000 conform-action transmit exceed-action drop
Can someone help me telling what command replace it or which is the equivalent?
Atte.
PercyEdison,
Thanks for helping with this it is greatly appreciated. I have been playing around with this and have managed to get the policing working successfully on the SVI.
The problem was basically the direction the policing was being applied. Initially I was applying the service policies to the customer SVIs in an inbound direction. This would only be traffic coming into the VLAN interface from within the VLAN; therefore, in terms of internet traffic this would be upload and NOT the required download.
In order to resolve this, I have applied the service policy to the Internet facing VLAN. Please see below -
Class Maps and Policy Maps
class-map match-all CUST-A-VL10-CMAP1
match input-interface FastEthernet1/0/24
class-map match-all CUST-A-VL10-CMAP2
match access-group name CUST-A-VL10-ACL-POL
policy-map CUST-A-VL10-PMAP1
class CUST-A-VL10-CMAP1
police 100000 18750 exceed-action drop
policy-map CUST-A-VL10-PARENT-PMAP1
class CUST-A-VL10-CMAP2
set ip precedence 1
service-policy CUST-A-VL10-PMAP1
VLAN Confguration
interface Vlan300
ip address ************
service-policy input CUST-A-VL10-PARENT-PMAP1
This works successfully and polices the traffic as expected. However, I have now run into the problem with assigning multiple service policies to the VLAN interface. As this is the internet facing VLAN for the routing of traffic to and from the internet, all customer service policies need to be applied to this interface. When I attempt to apply more than one service policy to this VLAN i receive the following error -
(config-if)#service-policy input CUST-B-VL20-PARENT-PMAP1
Policy map CUST-A-VL10-PARENT-PMAP1 is already attached
Looks like another couple of hours needed working around this problem!!
Thanks
Nick -
Can I rate-limit on the sub-interface in cisco asr 1013?
Hi,
I am looking for the command of rate-limit on a sub-interface in cisco asr 1013.
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.2(2)S, RELEASE SOFTWARE (fc1)
IOS XE Version: 03.06.00.S
Please let me know if it is possible in cisco asr 1013. If yes then what are the commands.
ZobairThe ASR no longer supports the rate-limit command, but it does support the same functionality in a QoS policy.
Please find a sample configuration -
ASR1004(config)#policy-map test
ASR1004(config-pmap)#class class-default
ASR1004(config-pmap-c)#shape average 10000
Applying for both ingress and egress : -
ASR1004(config)#int gig1/1/0
ASR1004(config-if)#service-policy output test
or
ASR1004(config-if)#service-policy input test -
Hello!
On my 3750me i do next configuration:
int vlan 999
ip address 10.0.0.1 255.255.255.252
rate-limit input 100000 8000 8000 conform-action transmit exceed-action drop
rate-limit output 100000 8000 8000 conform-action transmit exceed-action drop
Nothing happens. Please help rate-limit vlan. How can i do it?Hello,
don't know if you are still interested in this anyway I have 3 suggestions:
1. Check if mls qos is enabled (sh mls qos)
2. use MQC policer instead of old CAR
3. check the stats using sh mls qos interface x/x/x/ stat
regards,
Riccardo -
I'm throwing this out in hopes of finding a solution. I just purchased the Cisco SG300-28 to replace an old Catalyst 3548 switch. I have three VLAN's and I use a separate routing appliance. My VLANS I use are 1 (management/Trunk), 100 (Regular Access), and 101 (Restricted Access). On the Catalyst 3548 I statically assigned the ports for the Vlans. My servers use trunk ports to communicate between the VLANs for various services.
My problem is that when I setup the SG300-28 for trunk ports for the servers, I can communicate with them so long as I'm on another port that's not setup for the other two VLANS. Vlan 100 and 101 don't route or get DHCP anymore. I am also not able to ping back into the Vlans from the trunk ports.
I believe my issue is that I don't understand the difference between the old way of statically assigning Vlans to the ports from the new way. I was using V3 of the Cisco Networking Assistant which is different from the Web Interface of the Cisco SG300. It also could be that I wasn't using the trunk ports properly.
Either way, any assistance would certainly be appreciated. Thank you.
DJ SmithI did get this switch figured out finally and I apologize for not getting back to this sooner. I had crafted a response only to have this board dump it so I am using notepad to
save everything before posting.
Here is a basic diagram
/--------------{CISCO SG300-28}------------------------------------\
| | | | |
| | | | |
[Cisco 3548] [VMWare ESXi 3.5] [Windows SVR 2003] | |
[Port 13] [Port 28] [Port 27] [Ports 1-6] [Ports 7-12]
/ \ | | |
/ \ | | |
/ \ | | |
/ \ [VLAN1, 100] [WrkStns] [WrkStns]
/ \ [VLAN100] [VLAN101]
[Astaro GTWY ] [MS Svr 2008]
[VLAN1,100,101] [VLAN1 ]
VLAN1 - Management
VLAN100 - Main Network
VLAN101 - Restricted Network
I just put the main players on this setup. The problem I was having is that the workstations wouldn't communicate with any of these devices.
My problem was understanding how to use the web interface of the SG300 to get the devices to talk to the other devices.
In the Cisco 3548 setup using the Cisco Networking Assistant you setup the ports to the VLANS was very staight forward. Set 802.q and VLAN ID to the VLAN you wanted or ALL in
the case of the Servers.
With the Web interface, this is what I discovered:
Under Create VLAN, I had to create VLAN 100 and 101
Under Interface Settings, Set Ports g1-g6 to General. Administrative PVID to 100.
Then Set Ports g7 - g14 to General. Administrative PVID to 101
Then set Port g27 to General. Administrative PVID left to 1
Also set Port g28 to General. Again, left PVID to 1
Go to Port to VLAN settings;
Change VLAN ID = to 100 press GO
Select g1-g6 to untagged. Checked PVID box. Also checked g13, g27, g28 to tagged.
Changed VLAN ID = 101 Press GO
Select g7-g14 to untagged. Checked PVID box. Also checked g13, g28 to tagged. Verified g27 to untagged.
After that it was setup up like my old setup. Everything communicating as it should. -
Rate-limit command 3560 does it exist?
I have just come across a command in my router IOS which might be useful too me. I was wondering if the following command is available on a 3560 Switch. I don't see it on my 3550 but the IOS is quite old. I don't have a 3560 avaiable currently to check.
Config t > int vlan x > rate-limit input/output
does this exist on the 3560? I am also interest if it does in the Bits per second range and if available input/output.
Thanks for any helpHello,
what kind of feature are you looking for?
CAR?
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_command_reference_chapter09186a0080087f26.html#wp1037428
For command list check the following link:
Catalyst 3560 Switch Command Reference, Rel. 12.2(25)SEE
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/cr/index.htm
For QOS configs:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/scg/swqos.htm
If you need to rate limit traffic on an interface check:
Limiting the Bandwidth on an Egress Interface
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/scg/swqos.htm#wp1253412
Hope this help a bit,
if it does, please rate this post.
Vlad -
Service-Policy Or Bandwidth Rate Limit for IP
Hii Netpros,
Is this possible to configure the Service Policy(for Bandwidth) or Bandwidth Rate Limit for Single IP. For eg: If we want to configure the Service Policy(for Bandwidth) or Bandwidth Rate Limit of 2Mb for only IP " 10.10.10.3" on network i.e the Host or device which is configured with this IP can access upto 2Mb only.
Actual Network :- We need this to configure this for wireless customers, Actually we have created one Vlan 2 (IP:- 10.10.10.1/29 @ our end router) , 10.10.10.2 on Basestation wiresss device (Vlan 2 allowed on this wireless device) and this wireless device is working as point to multipoint wireless. i.e 2 or more then 2 wireless customers or last mile will connect to this basestation wireless. Wireless customer-1 is 10.10.10.3 (2Mb bandwidth) and Wireless Customer-2 10.10.10.4 (512Kb).
Hence we require to limit the bandwidth for this 2 wireless customers having different bandwidth. how to acheive & control bandwidth @ our end router for them. please suggest.
ThanksThis topic is probably better suited in another Infrastructure forum, but I suppose it depends on which features are supported by your Cisco hardware and software. This doc discusses a variety of options:
http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpolsh.html
For example, with the older CAR (committed access rate) approach:
interface FastEthernet5/0
rate-limit input access-group 101 20000000 [normal burst size] [excess burst size] conform-action transmit exceed-action drop
rate-limit input access-group 102 5120000 [normal burst size] [excess burst size] conform-action transmit exceed-action drop
access-list 101 permit ip 10.10.10.3 0.0.0.0
access-list 102 permit ip 10.10.10.4 0.0.0.0
You can observe CAR in action with "show interfaces fa5/0 rate-limit" for example. -
Hi,
Iam looking for a way to Rate Limit - Vlan interfaces,
Somting like this .. or do I need to change the service-policy to rate-limit for it to work
Interface Vlan2
Description Customer-A
service-policy input police-customerA-traffic
service-policy output police-customerA-traffic
ip address 10.10.10.1 255.255.255.252
Interface Vlan3
Description Customer-B
service-policy input police-customerB-traffic
service-policy output police-customerB-traffic
ip address 10.10.11.1 255.255.255.252
Interface Vlan4
Description Customer-C
service-policy input police-customerC-traffic
service-policy output police-customerC-traffic
ip address 10.10.12.1 255.255.255.252
Interface GigabitEthernet3/1
Description Trunk - Customer-A - Customer-C
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2,4
switchport mode trunk
Interface GigabitEthernet3/1
Description Trunk - Customer-B
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 3
switchport mode trunk
Is that posible ??, or do i need to make user based rate limit based on Source / destination adresses, and move the service policy to the physical interface ??
Hardware in this case Cisco 7609 running MPLS
Thanks in advance.
/PeterCan you explain your network topology a little?. This would help me to understand your network setup and help you in this issue accordingly.
-
Hi,
My network infrastructure as simple as following:
LAN(edge switches 3560).......>Aggregator switch(3750)........>Firewall(ASA 5510)........>Router.......>Internet
I define 3 wireless VLANs with 3 SSIDs on the Aggregator switch(3750):
1. one SSID for company employees.
2. one SSID for wireless IP phones.
3. one SSID for company guest which access only internet.
And the wireless APs connected to the LAN(edge switches) direct with trunks.
My question is how to apply a rate limit for SSID for company guest to access internet with B.W. of 128kbps only.
I tried policy map to be applied on the aggregator switch(3750) on the VLAN interface, but, it is not working.
So, any suggested help, please.Hi Ahmed:
With autonomous APs, rate limiting isn't possible. All the autonomous APs support is QoS and that's pretty iffy. At the core of the issue, you're dealing with radio waves and which ones arrive at the radio first, and who was prevented from talking because someone else was talking. Dealing with these QoS and traffic shaping/policing issues are really tough with wireless because the transmission medium itself is unreliable.
The "Configuring QoS" chapter of the autonomous AP configuration guide
http://tools.cisco.com/squish/5aCf1
will show you how you can map priority tagging to an SSID so that in that path from radio receiver to outbound on the fastethernet interface toward the rest of the network, you can control which SSID's packets get up into the network first, but the reverse path is a different story. Because the wireless medium is half-duplex acknowledged, you can have a high priority packet out there on the radio interface trying to be beamed out to the client, and if the client isn't sending their ACK or what have you, it's going to sit and retry until its 63 retries are done before it gets out of the way to let the next high priority packet have a turn at getting transmitted out.
Once the traffic gets past the edge switch, the fact that it was at one time wireless is irrelevant. You should look at it as a general "rate limiting one VLAN's traffic over another" and check with the routing protocols or traffic shaping folks.
Sincerely,
Rollin Kibbe
Network Management Systems Team -
3750X rate-limit (QoS)
Hello,
I'm trying to configure a rate-limit in a 3750X but I'm not seeing any result...
These are my configurations:
RF#show run
Building configuration...
Current configuration : 23410 bytes
! Last configuration change at 08:53:35 UTC Sun Mar 14 1993
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname RF
boot-start-marker
boot-end-marker
no aaa new-model
switch 1 provision ws-c3750x-48p
system mtu routing 1500
ip routing
ip domain-name erf.carco.com.mx
rep admin vlan 100
mls qos
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 2
vlan 4
vlan 6
vlan 8
vlan 10
vlan 20
vlan 21
vlan 22
vlan 23
vlan 25
vlan 26
vlan 30
vlan 50
vlan 53
vlan 70
vlan 81
vlan 91
vlan 92
vlan 93
vlan 95
vlan 96
vlan 99
vlan 100
vlan 102
vlan 110
vlan 122
vlan 129
vlan 200
vlan 213
vlan 227
vlan 333
vlan 357
vlan 417
vlan 444
vlan 500
vlan 502
vlan 555
vlan 700
vlan 712
vlan 910
vlan 911
vlan 951
vlan 1105
vlan 1508
vlan 1830
vlan 1870
vlan 1890
vlan 1891
vlan 1892
class-map match-any test
match access-group 100
policy-map test
class test
police 150000000 512000 exceed-action drop
interface Loopback0
ip address 10.20.40.106 255.255.255.0
interface Port-channel22
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
rep segment 10
interface Port-channel24
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
rep segment 10
interface FastEthernet0
no ip address
no ip route-cache
shutdown
interface GigabitEthernet1/0/1
interface GigabitEthernet1/0/2
interface GigabitEthernet1/0/3
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
no logging event link-status
shutdown
speed 1000
duplex full
interface GigabitEthernet1/0/4
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
speed 1000
duplex full
interface GigabitEthernet1/0/5
interface GigabitEthernet1/0/6
interface GigabitEthernet1/0/7
interface GigabitEthernet1/0/8
interface GigabitEthernet1/0/9
interface GigabitEthernet1/0/10
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/11
interface GigabitEthernet1/0/12
interface GigabitEthernet1/0/13
interface GigabitEthernet1/0/14
interface GigabitEthernet1/0/15
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/16
interface GigabitEthernet1/0/17
interface GigabitEthernet1/0/18
interface GigabitEthernet1/0/19
interface GigabitEthernet1/0/20
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/21
interface GigabitEthernet1/0/22
interface GigabitEthernet1/0/23
interface GigabitEthernet1/0/24
interface GigabitEthernet1/0/25
switchport access vlan 910
switchport mode access
interface GigabitEthernet1/0/26
interface GigabitEthernet1/0/27
interface GigabitEthernet1/0/28
interface GigabitEthernet1/0/29
interface GigabitEthernet1/0/30
interface GigabitEthernet1/0/31
interface GigabitEthernet1/0/32
interface GigabitEthernet1/0/33
interface GigabitEthernet1/0/34
interface GigabitEthernet1/0/35
interface GigabitEthernet1/0/36
interface GigabitEthernet1/0/37
no switchport
bandwidth 150000
ip address 10.20.103.13 255.255.255.252
rate-limit output access-group 100 24000000 3000000 3000000 conform-action transmit exceed-action drop
logging event link-status
interface GigabitEthernet1/0/38
interface GigabitEthernet1/0/39
interface GigabitEthernet1/0/40
interface GigabitEthernet1/0/41
interface GigabitEthernet1/0/42
interface GigabitEthernet1/0/43
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
channel-group 24 mode on
interface GigabitEthernet1/0/44
interface GigabitEthernet1/0/45
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/0/47
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
channel-group 22 mode on
interface GigabitEthernet1/0/48
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,7,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
logging event link-status
shutdown
interface GigabitEthernet1/1/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,60,70,91-93,95,96,99,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/1/2
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,60,70,91-93,95,96,99,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/1/3
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,6,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
logging event link-status
shutdown
interface GigabitEthernet1/1/4
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,6,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
logging event link-status
shutdown
interface TenGigabitEthernet1/1/1
interface TenGigabitEthernet1/1/2
interface Vlan1
no ip address
shutdown
interface Vlan6
description ***LANERF**
ip address 10.20.6.106 255.255.255.0
no ip redirects
interface Vlan23
description < TRANSITO MUR >
no ip address
no ip redirects
interface Vlan100
description < VLAN MAN >
ip address 10.20.100.106 255.255.255.0
no ip redirects
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 7 032368342B2F0F
ip ospf dead-interval minimal hello-multiplier 4
router ospf 1
router-id 10.20.40.106
auto-cost reference-bandwidth 100000
area 0.0.0.0 authentication message-digest
area 1.80.1.1 authentication message-digest
redistribute connected subnets
redistribute static subnets
passive-interface default
no passive-interface Vlan23
no passive-interface Vlan100
no passive-interface GigabitEthernet1/0/37
network 10.20.6.0 0.0.0.0 area 0.0.0.0
network 10.20.40.106 0.0.0.0 area 0.0.0.0
network 10.20.91.6 0.0.0.0 area 0.0.0.0
network 10.20.100.106 0.0.0.0 area 0.0.0.0
default-information originate
ip http server
ip http secure-server
access-list 100 permit ip 10.50.80.0 0.0.0.255 10.80.80.0 0.0.0.255
access-list 100 permit ip 10.80.80.0 0.0.0.255 10.50.80.0 0.0.0.255
snmp-server community ASComRO RO
line con 0
line vty 0 4
login
line vty 5 15
login
event manager applet track_qos_down authorization bypass
event syslog pattern "TRACKING-5-STATE: 15 ip sla 15 reachability Up->Down"
action 1 cli command "enable"
action 2 cli command "configure terminal"
action 3 cli command "interface giga1/0/37"
action 4 cli command "rate-limit output access-group 100 400000000 50000000 50000000 conform-action transmit exceed-action drop"
action 5 cli command "end"
event manager applet track_qos_up authorization bypass
event syslog pattern "TRACKING-5-STATE: 15 ip sla 15 reachability Down->Up"
action 1 cli command "enable"
action 2 cli command "configure terminal"
action 3 cli command "interface giga1/0/37"
action 4 cli command "no rate-limit output access-group 100 400000000 50000000 50000000 conform-action transmit exceed-action drop"
action 5 cli command "end"
end
ERF#
ERF#show mls qos
QoS is enabled
QoS ip packet dscp rewrite is enabled
ERF#show mls qos inter gigabitEthernet 1/0/37
GigabitEthernet1/0/37
trust state: not trusted
trust mode: not trusted
trust enabled flag: ena
COS override: dis
default COS: 0
DSCP Mutation Map: Default DSCP Mutation Map
Trust device: none
qos mode: port-based
When I apply the command I'm seeing a gauge using a 3rd party but I'm not seeing that the traffic will be truncated @ 50Mbps.
Any thoughts???Hi
Bandwidth commands allocates the particular amount of bandwidth you mention or configure over there.
Basically you have the liberty to configure upto 75% of the available interface bandwidth to different classes.
most widelys used with CBWFQ technique..
so while configuring up the same better to watch out for the exact bandwidth value keyed in on the interface to have your alloocation work properly.
policing basically used for limiting the traffic or to control the bursts by dropping them or marking them with different ip precedence or DSCP values.
its very much similar to the rate-limit command applied on the interface level which again uses token bucket system either single or dual based on the configuration parameters.
for more info on above mentioned clis do check these links..
http://www.cisco.com/en/US/tech/tk543/tk545/tsd_technology_support_protocol_home.html
http://www.cisco.com/en/US/tech/tk543/tk544/tsd_technology_support_protocol_home.html
regds -
Communication problem between Cisco 3560 and Cisco SG300.
Dear Support,
I have a Cisco SG300 and Cisco 3560 switches.
3560 is my Core Switch and SG300 is access switch.
From 3560 VLAN information is not passed to SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Please suggest how this issue is resolve.
Regards,
JItesh Mahajan.Dear Aleksandra,
Below Configuration is right or wrong for 3560 and SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan remove VLAN 1
switchport native vlan 1
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Regards,
JItesh Mahajan. -
Possible to rate limit console input?
I built a tool that allows us to input device information such as IP, VLAN, etc, etc and this tool builds the entire config file that can be pasted into a switch/router. The problem is that when I start getting down near the banner and motd sections, the console cannot keep up with the input and it drops lines of input.
Is there a way to rate limit the input when large configs are pasted into con 0?I built a tool that allows us to input device information such as IP, VLAN, etc, etc and this tool builds the entire config file that can be pasted into a switch/router. The problem is that when I start getting down near the banner and motd sections, the console cannot keep up with the input and it drops lines of input.
Is there a way to rate limit the input when large configs are pasted into con 0? -
Cisco SG300 - IGMP and multiple switches
Hi all,
I have read through various Cisco documents and tried various configurations and i have been unsuccessful
Here is the network layout
Cisco SG300-10 in Layer 3 mode, managing all VLANS created and inter-vlan traffic is working fine
Ports 1-4 are in LAG 1 with LACP enabled, Ports 5-8 are in LAG 2 again with LACP enabled, port 9 is connected to the ASA 5505 (Trunk port, all VLANS) and port 10, again a trunk port I use for management
LAG 1 and 2 are connected to Cisco SG300-52 switches
again traffic between the switches is working ok, what we would like to do is the following
on VLAN 7, we have multiple devices streaming using UDP multicast, what we would like to do is allow PC's on VLAN 5 to be able to pick up these streams as and when they need to, the devices broadcast on their own unique UDP ranges
Could someone please explain to me what I need to configure on the Layer 3 switch and the other two Layer 2 switches in order for this to work?
If i put a port into VLAN 7 and can view the stream without a problem, also if there is any fine tuning to be done once this is working
Thanks
AndyJason,
The only advantage you would get from using SFPs (fiber tranceivers) in the GBIC slots would be if you needed to make a run of over 100m between the switches. Unless you have a very large property with switches at either end you are just as well to use the copper ports in the setup you described. There is also nothing wrong with chaining the SG100s together if necessary to free up a port on the RV320. The only other thing to consider is if you are using VLANs. Each unmanaged SG100 will only pass a single VLAN so if you need segregated distribution coming from the RV320 you would need to put each SG100 on its own port. Or, you could run a trunk from a port on the RV320 to your SG200 and then split off your untagged VLANs from there. Hope this answers your question and have a nice day.
Regards,
Mike.V -
Per user bandwidth rate limit.
How to configure per user bandwidth rate limit for wireless guest client, authentication server is ISE 1.2 & wireless controller is 5760.
The Cisco 5760 WLC supports better QoS than other c
ontrollers, allowing prioritization of mission-crit
ical
applications:
●
The Cisco 5760 WLC supports four wireless hardware
queues and priority-based queuing compared to
software-based queuing in existing controllers.
●
The Cisco 5760 WLC follows MQC based commands, allo
wing usage of exact commands for configuring
QoS on different types of network devices.
●
The Cisco 5760 WLC supports QoS policies to be appl
ied in a hierarchical fashion with more granularity
per SSID per radio, while on the current controller
s granularity is per WLAN.
●
The Cisco 5760 WLC supports approximate fair bandwi
dth to make sure of fairness at client, SSID, and
radio levels for Non-Real Time (NRT) traffic. There
fore, if one user consumes excessive bandwidth, we
can
limit the amount of bandwidth that user receives an
d thereby not deprive other users.
Maybe you are looking for
-
Is Adobe really turning its back on me?
In 2005, I purchased the entire Adobe Creative Suite 2 Premium. I really only needed and wanted Photoshop CS2, but for the extra money, I bit the bullet and got the rest thinking that I may end up using it. It worked great and still does, with the ex
-
IPhoto/Facebook export issues
My iPhoto is not exporting to Facebook properly. Either it simply does nothing after I click on the appropriate buttons (when it used to say " X photos upload to your Facebook Album", or it crashes and closes or it uploads the incorrect photos. I hav
-
why the *** the messagin app is not able to send txt mesage to two or more receipants at a time, when i am able to send the same message to both of them seperately....as it is sending to each person properly, its not prob with SIM/wifi/messaging cen
-
Burning a playable DVD. No technical jargon please!
I have asked a simliar question before and it is probably quite elementary but I am not familiar with how to do this. I want to take a "movie" from FCP and burn it to a DVD (that will play in a player) using DVD studio pro or whatever works. What is
-
The photos are clear for the firt instant the appear during palyback and for the 3 or 4 seconds they are on the screen any pattern or design in the photo, say a patterned tablecloth, the pattern goes wavy, distorted, and then at the last moment befor