Can I rate-limit on the sub-interface in cisco asr 1013?

Hi,
I am looking for the command of rate-limit on a sub-interface in cisco asr 1013.
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.2(2)S, RELEASE SOFTWARE (fc1)
IOS XE Version: 03.06.00.S
Please let me know if it is possible in cisco asr 1013. If yes then what are the commands.
Zobair

The ASR no longer supports the rate-limit command, but it does support the same functionality in a QoS policy.
Please find a sample configuration -
ASR1004(config)#policy-map test
ASR1004(config-pmap)#class class-default
ASR1004(config-pmap-c)#shape average 10000
Applying for both ingress and egress : -
ASR1004(config)#int gig1/1/0
ASR1004(config-if)#service-policy output test
or
ASR1004(config-if)#service-policy input test

Similar Messages

Do the sub-interface of ASA firewall has limit of bandwidth

do the sub-interface of ASA firewall has limit of bandwidth? or how does the bandwidth of the physical interface divided among the sub-interface? is there a cisco documentation url link that explains this?

Nakayama-san,
The configuration recommendation to limit the traffic entering the router was intended for legacy (i.e. non-ISR routers). Since you are using a 2811, I would recommend that you test WAAS without these limitations configured.
Thanks,
Zach

Can we specify limit on the number of records to be fetched?

Can we specify limit on the number of records to be fetched from the database?
I have millions of records in my DB and I want to fetch say some 50,000 latest records to optimize the performance of reports.
Is it possible in any version of Crystal Reports?
Regards,
Amrita

Hi Amrita
Do you have any groups in your report. If yes then this is what you need to do:
1) Insert a section below on the Details section so that there is a Details A and Details B.
2) Create the following formulas:
@Formula1
WhilePrintingRecords;
NumberVar Number := 0;
@Formula2
WhilePrintingRecords;
NumberVar Number;
Number := Number + 1;
3) Place @Formula1 in the Group Header. Format the formula to Suppress.
4) Place @Formula2 in Details A. Format the SECTION (not the formula) to Suppress.
5) Format the Details B section to conditionally Suppress by selecting the X+2 button INSTEAD of the selecting the Suppress box. This launches the conditional formatting Formula Editor.
6) Enter this formula:
{@formula2} > 3
When you preview the report you will only see 3 records per group.
Let us know if you need any further help with this.
Regards
Girish Bhosale

Include multiple sub-interfaces in Cisco ASA for VPN tunnel

I am trying to create a VPN tunnel between two Cisco ASAs where one ASA has multiple sub-interfaces.
Say, In Cisco ASA 5550(in datacentre), I created multiple subinterfaces with VLAN ID as below:
Inside, int0/1 : 10.1.1.0/24
DMZ, int0/1.100: 10.1.100.0/24 (VLAN 100)
Production, int 0/1.101 : 10.1.101.0/24 (VLAN 101)
Management, int 0/1.102: 10.1.102.0/24 (VLAN 102)
And another Cisco ASA 5505 is only configured with 1 x inside interface Inside, int 0/1: 192.168.1.0/24
So far, I have only been able to provide outside access to one of the sub-interfaces as NAT rule on inside interface didn't work for VLANs. Hence had to issue Global NAT rule to be applied on Production subinterface so that production VLAN can have outside access. I have managed to establish VPN tunnel between two ASAs on Production sub-interface only, Source interface = Production subinterface
Additional settings:
Have ACL to allow all sub interfaces to access outsite ( lower security level)
NAT rules is configured on Production subinterface with Source NAT Type as Dynamic PAT; when this was configured with source interface as inside, PCs behind various VLAN coun't access internet.
I want to establish a site-to-site VPN tunnel with multiple sub-interfaces of Cisco ASA 5550 to Cisco ASA 5505. Would you please suggest what I am missing in my configuration? I need to be able to access multiple VLANs of datacentre from remote site.

I am trying to create a VPN tunnel between two Cisco ASAs where one ASA has multiple sub-interfaces.
Say, In Cisco ASA 5550(in datacentre), I created multiple subinterfaces with VLAN ID as below:
Inside, int0/1 : 10.1.1.0/24
DMZ, int0/1.100: 10.1.100.0/24 (VLAN 100)
Production, int 0/1.101 : 10.1.101.0/24 (VLAN 101)
Management, int 0/1.102: 10.1.102.0/24 (VLAN 102)
And another Cisco ASA 5505 is only configured with 1 x inside interface Inside, int 0/1: 192.168.1.0/24
So far, I have only been able to provide outside access to one of the sub-interfaces as NAT rule on inside interface didn't work for VLANs. Hence had to issue Global NAT rule to be applied on Production subinterface so that production VLAN can have outside access. I have managed to establish VPN tunnel between two ASAs on Production sub-interface only, Source interface = Production subinterface
Additional settings:
Have ACL to allow all sub interfaces to access outsite ( lower security level)
NAT rules is configured on Production subinterface with Source NAT Type as Dynamic PAT; when this was configured with source interface as inside, PCs behind various VLAN coun't access internet.
I want to establish a site-to-site VPN tunnel with multiple sub-interfaces of Cisco ASA 5550 to Cisco ASA 5505. Would you please suggest what I am missing in my configuration? I need to be able to access multiple VLANs of datacentre from remote site.

Rate Limit on the MPLS Tag interface

In MPLS Networks, we generally enable tag-switching IP and MTU (1526) configuration on the specific interface . Say if the above commands are applied in the 2 mb Lease Line Serial interface , How do i rate Limit to 64K ?
Can anyone provide me this info w.r.t the configuration?
Regards
Srikant

Generic rate-limiting should be possible. Here's a URL explaining how to configure this feature.
http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_command_reference_chapter09186a00801a7ee1.html#1080850
Hope this helps,

FAQ: Where can I learn more about the SpeedGrade interface?

The SpeedGrade interface can be confusing if you don't know where to look. See this video tutorial by Patrick Inhofer for a full tour of the SpeedGrade CC interface.

Apple has what they call "online seminars" available on the main Logic page
http://www.apple.com/logicpro/
If you look on the bottom right hand side of the page, you see a link for online seminars. You'll have to go through a regstration process, then you can watch 3 or 4 streaming Quicktime videos of people using different functions in Logic. There's nothing really in depth there, but it does show you a few useful shortcuts and methods.

I can not receive email through the webmail interface

This started today. I am able to send from my verizon account to my netzero, but do not receive anything when I send from netzero to verizon. There are no error messages. I am using IE 9 (Win 7) and also tried with firefox. Is anyone else having issues in S/E Pennsylvania (Swarthmore)? Thanks, Jose
I also use zoho to manipulate my VZ mail (I leave a copy on the server) and the issue persists there, Zoho support could not find any issues on their end
If a forum member gives an answer you like, please give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. Thanks !!!
http://forums.verizon.com/t5/Verizon-net-Email/Fix-for-Missing-Inbox-sent-folders-etc-with-Internet-Explorer-11/m-p/647399
Solved!
Go to Solution.

I have a very long blocked senders list and I added netzero to the list by mistake. (HUGE FACEPALM)
If a forum member gives an answer you like, please give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. Thanks !!!
http://forums.verizon.com/t5/Verizon-net-Email/Fix-for-Missing-Inbox-sent-folders-etc-with-Internet-Explorer-11/m-p/647399

High receive discards on Sub-Interfaces in Cisco ASA.

Hello Everyone,
Over the past few weeks Solarwinds is reporting high receive discards on two of our subinterfaces created on Cisco ASA. No errors are observed on other subinterfaces. I checked the trunk port interface on the switch for any errors but found none. These errors are visible only under subinterface. What could be the issue?
Regards

I have the same problem too.
I have Cisco ASA 5515 with the next version:
Cisco Adaptive Security Appliance Software Version 9.1(4)
My interface configuration is the next:
PortChannel5 made with Interface GigabitEthernet 0/2 + Interface GigabitEthernet 0/3
Subinterfaces in PortChannel5
Nagios Graphs shows:
- many input discards in virtual subinterfaces
- many output discards in interface Gi0/2 and Gi0/3
- PortChannel5 output discards is the sum of discards in interface Gi0/2 and Gi0/3
if I run the snmpwalk command against the ASA the following results were obtained:
Interface description
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c XXXXXXX 10.255.16.1 | grep ifDescr
IF-MIB::ifDescr.2 = STRING: Adaptive Security Appliance 'asa_mgmt_plane' interface
IF-MIB::ifDescr.3 = STRING: Adaptive Security Appliance 'Internet' interface
IF-MIB::ifDescr.4 = STRING: Adaptive Security Appliance 'LAN_MPLS' interface
IF-MIB::ifDescr.5 = STRING: Adaptive Security Appliance 'GigabitEthernet0/2' interface
IF-MIB::ifDescr.6 = STRING: Adaptive Security Appliance 'GigabitEthernet0/3' interface
IF-MIB::ifDescr.7 = STRING: Adaptive Security Appliance 'stateifha' interface
IF-MIB::ifDescr.8 = STRING: Adaptive Security Appliance 'statelink' interface
IF-MIB::ifDescr.9 = STRING: Adaptive Security Appliance 'Internal-Data0/1' interface
IF-MIB::ifDescr.10 = STRING: Adaptive Security Appliance 'cplane' interface
IF-MIB::ifDescr.11 = STRING: Adaptive Security Appliance 'mgmt_plane_int_tap' interface
IF-MIB::ifDescr.12 = STRING: Adaptive Security Appliance 'management' interface
IF-MIB::ifDescr.13 = STRING: Adaptive Security Appliance 'Virtual254' interface
IF-MIB::ifDescr.14 = STRING: Adaptive Security Appliance 'Port-channel5' interface
IF-MIB::ifDescr.15 = STRING: Adaptive Security Appliance 'VLAN_USGLB_OOB' interface
IF-MIB::ifDescr.16 = STRING: Adaptive Security Appliance 'VLAN_USGLBHSTHYP_MGNT' interface
IF-MIB::ifDescr.17 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_OM' interface
IF-MIB::ifDescr.18 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_MGNTOM' interface
IF-MIB::ifDescr.19 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_MGNT' interface
IF-MIB::ifDescr.20 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_SRVF' interface
IF-MIB::ifDescr.21 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_SRVB' interface
IF-MIB::ifDescr.22 = STRING: Adaptive Security Appliance 'VLAN_USGLB_DMZ' interface
Input discards
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c xxxxxxxxxx 10.255.16.1 | grep ifInDiscards
IF-MIB::ifInDiscards.2 = Counter32: 0
IF-MIB::ifInDiscards.3 = Counter32: 0
IF-MIB::ifInDiscards.4 = Counter32: 0
IF-MIB::ifInDiscards.5 = Counter32: 0
IF-MIB::ifInDiscards.6 = Counter32: 0
IF-MIB::ifInDiscards.7 = Counter32: 0
IF-MIB::ifInDiscards.8 = Counter32: 0
IF-MIB::ifInDiscards.9 = Counter32: 0
IF-MIB::ifInDiscards.10 = Counter32: 0
IF-MIB::ifInDiscards.11 = Counter32: 0
IF-MIB::ifInDiscards.12 = Counter32: 0
IF-MIB::ifInDiscards.13 = Counter32: 0
IF-MIB::ifInDiscards.14 = Counter32: 0
IF-MIB::ifInDiscards.15 = Counter32: 12481926
IF-MIB::ifInDiscards.16 = Counter32: 9927941
IF-MIB::ifInDiscards.17 = Counter32: 134120211
IF-MIB::ifInDiscards.18 = Counter32: 124695686
IF-MIB::ifInDiscards.19 = Counter32: 27081148
IF-MIB::ifInDiscards.20 = Counter32: 2941537222
IF-MIB::ifInDiscards.21 = Counter32: 32714719
IF-MIB::ifInDiscards.22 = Counter32: 4008856
Output discards
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c xxxxxxxxxxxx 10.255.16.1 | grep ifOutDiscards
IF-MIB::ifOutDiscards.2 = Counter32: 0
IF-MIB::ifOutDiscards.3 = Counter32: 0
IF-MIB::ifOutDiscards.4 = Counter32: 0
IF-MIB::ifOutDiscards.5 = Counter32: 3635696
IF-MIB::ifOutDiscards.6 = Counter32: 119099
IF-MIB::ifOutDiscards.7 = Counter32: 0
IF-MIB::ifOutDiscards.8 = Counter32: 0
IF-MIB::ifOutDiscards.9 = Counter32: 0
IF-MIB::ifOutDiscards.10 = Counter32: 0
IF-MIB::ifOutDiscards.11 = Counter32: 0
IF-MIB::ifOutDiscards.12 = Counter32: 0
IF-MIB::ifOutDiscards.13 = Counter32: 0
IF-MIB::ifOutDiscards.14 = Counter32: 3754795
IF-MIB::ifOutDiscards.15 = Counter32: 0
IF-MIB::ifOutDiscards.16 = Counter32: 0
IF-MIB::ifOutDiscards.17 = Counter32: 0
IF-MIB::ifOutDiscards.18 = Counter32: 0
IF-MIB::ifOutDiscards.19 = Counter32: 0
IF-MIB::ifOutDiscards.20 = Counter32: 0
IF-MIB::ifOutDiscards.21 = Counter32: 0
IF-MIB::ifOutDiscards.22 = Counter32: 0
Output discards may be normals, but I don't understand input discards in virtual subinterfaces of PortChannel5
By the other hand, show interface command in subinterfaces don't show error or discards packets
FIREWALL01/pri/act# sh interface VLAN_USGLBVRM_SRVB detail
Interface Port-channel5.1020 "VLAN_USGLBVRM_SRVB", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 1020
Description: VLAN_USGLBVRM_SRVB
MAC address 6073.5c69.0917, MTU 1500
IP address 10.255.19.65, subnet mask 255.255.255.192
Traffic Statistics for "VLAN_USGLBVRM_SRVB":
42067433644 packets input, 45125599467459 bytes
28153119062 packets output, 8866514693262 bytes
32715765 packets dropped
Control Point Interface States:
Interface number is 21
Interface config status is active
Interface state is active
Control Point Vlan1020 States:
Interface vlan config status is active
Interface vlan state is UP
FIREWALL01/pri/act# sh interface VLAN_USGLBVRM_SRVF detail
Interface Port-channel5.1019 "VLAN_USGLBVRM_SRVF", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 1019
Description: VLAN_USGLBVRM_SRVF
MAC address 6073.5c69.0917, MTU 1500
IP address 10.255.19.1, subnet mask 255.255.255.192
Traffic Statistics for "VLAN_USGLBVRM_SRVF":
30475814698 packets input, 14615432248013 bytes
27472348465 packets output, 20872697455933 bytes
2941588838 packets dropped
Control Point Interface States:
Interface number is 20
Interface config status is active
Interface state is active
Control Point Vlan1019 States:
Interface vlan config status is active
Interface vlan state is UP
FIREWALL01/pri/act#
Can anyone explain why so many input errors appear in the subinterfaces?
Thanks in advance!

ASR9000/XR - BNG - L3 sub-interface limit for trunk (4096) error - what is the work around?

We currently have 7,500 broadband subscribers that we will be terminating on our ASR 9001.
Each one of our customers will be terminating on a sub-interface on a bundle.
On the 9k, there will be a QoS policy applied to rate-limit their broadband connection (see example below).
The challenge that we are running into right now is scaling beyond 4096 L3 sub-interfaces. When running through this in our lab, we receive the following fail message:
RP/0/RSP0/CPU0:BNG(config-subif)#show config failed
Tue Mar 10 18:32:07.552 UTC
!! SEMANTIC ERRORS: This configuration was rejected by
!! the system due to semantic errors. The individual
!! errors with each failed configuration command can be
!! found below.
interface Bundle-Ether10.6941171
!!% The L3 sub-interface limit for the trunk interface has been reached: Trunk limit for L3 subinterfaces on Bundle-Ether10 is 4096
We have added the following on to each of the sub-interfaces to "fake" out the NPU, but even with SPD configured, we are receiving the max 4096 message:
service-policy output <POLICY> subscriber-parent resource-id 0
service-policy output <POLICY> subscriber-parent resource-id 1
service-policy output <POLICY> subscriber-parent resource-id 2
service-policy output <POLICY> subscriber-parent resource-id 3
It is my understanding that we have a total of 4 resource ID's to use (0-3) and the ASR 9001 will support up to 32,000 sub-interfaces (system wide or 8,000 sub interfaces per resource-id).
See attached image for reference this design.
Main question to the community is what is the work around to scale beyond 4096 L3 sub-interfaces??
In our case it is not feasible to bring in additional bundles and spread the customers out.
Look forward to your responses.
Below is a sample configuration:
policy-map 10M_D
class class-default
shape average 10100000 bps
end-policy-map
policy-map 10M_U
class class-default
police rate 10300000 bps
exceed-action drop
end-policy-map
interface Bundle-Ether10.650102
description ---INT: GigabitEthernet0/0/1.650102 NAME: TEST #1---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 0
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 102
interface Bundle-Ether10.650103
description ---GigabitEthernet0/0/1.650103 NAME: TEST #2---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 1
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 103
interface Bundle-Ether10.650104
description ---INT: GigabitEthernet0/0/1.650104 NAME: TEST #3---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 2
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 104
interface Bundle-Ether10.650105
description ---INT: GigabitEthernet0/0/1.650105 NAME: TEST #4---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 3
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 105
interface Bundle-Ether10.650106
description ---INT: GigabitEthernet0/0/1.650106 NAME: TEST #5---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 0
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 106
interface Bundle-Ether10.650107
description ---INT: GigabitEthernet0/0/1.650107 NAME: TEST #6---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 1
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 107
interface Bundle-Ether10.650108
description ---INT: GigabitEthernet0/0/1.650108 NAME: TEST #7---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 2
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 108
interface Bundle-Ether10.650109
description ---INT: GigabitEthernet0/0/1.650109 NAME: TEST #8---
service-policy input 10M_U
service-policy output 10M_D subscriber-parent resource-id 3
ipv4 point-to-point
local-proxy-arp
ipv4 unnumbered Loopback10
encapsulation dot1q 650 second-dot1q 109

xander,
Thanks for sharing the QinQ username, works perfectly.
couple of design questions for you.
#1 - If i have >7500 subscribers that will be terminating on this bundle, would this be the best design to ensure that i can scale up to 32,000 subscribers on the BE <leveraging the subscriber-parent resource-id (0-4)>
EXAMPLE
interface Bundle-Ether10.100
description BE10.100 – Area 1 - BNG customers - QinQ
ipv4 point-to-point
ipv4 unnumbered Loopback0
service-policy output <POLICY> subscriber-parent resource-id 0
service-policy type control subscriber IP_PM
ipsubscriber ipv4 l2-connected
initiator dhcp
encapsulation ambiguous dot1q 100 second-dot1q any
interface Bundle-Ether10.200
description BE10.200 – Area 2 - BNG customers - QinQ
ipv4 point-to-point
ipv4 unnumbered Loopback0
service-policy output <POLICY> subscriber-parent resource-id 1
service-policy type control subscriber IP_PM
ipsubscriber ipv4 l2-connected
initiator dhcp
encapsulation ambiguous dot1q 200 second-dot1q any
interface Bundle-Ether10.300
description BE10.300 – Area 3 - BNG customers - QinQ
ipv4 point-to-point
ipv4 unnumbered Loopback0
service-policy output <POLICY> subscriber-parent resource-id 3
service-policy type control subscriber IP_PM
ipsubscriber ipv4 l2-connected
initiator dhcp
encapsulation ambiguous dot1q 300 second-dot1q any
interface Bundle-Ether10.400
description BE10.400 – Area 4 - BNG customers - QinQ
ipv4 point-to-point
ipv4 unnumbered Loopback0
service-policy output <POLICY> subscriber-parent resource-id 4
service-policy type control subscriber IP_PM
ipsubscriber ipv4 l2-connected
initiator dhcp
encapsulation ambiguous dot1q 400 second-dot1q any
#2 - How do I verify in XR the CoA speed profile that is pushed down from RADIUS to a given subscriber?
I thought I might see the dynamic policy using the command below, but no luck.
Do you know the correct command?
RP/0/RSP0/CPU0:bng-asr9001#show policy-map inter be10.1.ip5
Wed Apr 1 14:12:06.390 UTC
Bundle-Ether10.1.ip5 input: __sub_55ffffff8b7dffffffad
Class class-default
Classification statistics (packets/bytes) (rate - kbps)
Matched : 126959/10831088 14
Transmitted : N/A
Total Dropped : N/A
Policy __sub_55ffffff8b7dffffffad_child1 Class class-default
Classification statistics (packets/bytes) (rate - kbps)
Matched : 126959/10831088 14
Transmitted : N/A
Total Dropped : 325/322582 0
Policing statistics (packets/bytes) (rate - kbps)
Policed(conform) : 126634/10508506 14
Policed(exceed) : 325/322582 0
Policed(violate) : 0/0 0
Policed and dropped : 325/322582
Policed and dropped(parent policer) : N/A
Bundle-Ether10.1.ip5 output: __sub_6effffff81ffffffbfffffffdb
Class class-default
Classification statistics (packets/bytes) (rate - kbps)
Matched : 199642/280153690 453
Transmitted : N/A
Total Dropped : N/A
Policy __sub_6effffff81ffffffbfffffffdb_child1 Class class-default
Classification statistics (packets/bytes) (rate - kbps)
Matched : 199642/280153690 453
Transmitted : N/A
Total Dropped : 26930/38989025 61
Policing statistics (packets/bytes) (rate - kbps)
Policed(conform) : 172712/241164665 392
Policed(exceed) : 26930/38989025 61
Policed(violate) : 0/0 0
Policed and dropped : 26930/38989025
Policed and dropped(parent policer) : N/A
RP/0/RSP0/CPU0:bng-asr9001#
#3 - CoA QoS profile -> I'm using the following avpair for ingress / egress qos. However when validating against a speed test server, my results are well above the 10Mbps / 10Mbps I have provisioned. Actual is more of in the ~15Mbps/15Mbps range.
Am I missing additional config in the policing section?
cisco-avpair = "ip:qos-policy-in=add-class(sub, (class-default,class-default),police(10000))",
cisco-avpair += "ip:qos-policy-out=add-class(sub, (class-default,class-default),police(10000))"
Appreciate it in advance xander!
-ae

LMS 4.2 sub-interface not available in the instance selection window creating poller

Hi All,
I have sub-interfaces created on the switch and are in active(up/up) state,but these sub-interface not available for selection in the instance window while creating the poller, and am not able to monitor the traffic on these sub interface in the performance management.
LMS will not display the interfaces in the instance selection window if they are not active,but here the sub-interface are in active state but these are
not available. can anyboody help me out ??
Thanks,
Channa

Any Idea..??

Can't get the Home interface of a Session bean,please!

when I run a client of a SessionBean,(use command "java ....";
the Exception was thrown:
java.lang.ClassCastException
at com.sun.corba.se.internal.javax.rmi.PortableRemoteObject.narrow(PortableRemoteObject.java:293)
at javax.rmi.PortableRemoteObject.narrow(PortableRemoteObject.java:134)
at clientTest.ClientTest.main(ClientTest.java:35)
the mothed main() :
java.util.Properties jndiProperties = new java.util.Properties();
jndiProperties.put("java.naming.provider.url","iiop://localhost:3700");
jndiProperties.put("java.naming.factory.initial","com.sun.jndi.cosnaming.CNCtxFactory");
try {
javax.naming.directory.DirContext jndiCtx = new javax.naming.directory.InitialDirContext(jndiProperties);
Object obj = jndiCtx.lookup("ejb/Stock");
System.out.println(obj);
StockHome sh = (StockHome)PortableRemoteObject.narrow(obj, StockHome.class); //exception was thrown
}catch (javax.naming.NamingException ne) {
ne.printStackTrace();
} catch (Exception e){
e.printStackTrace();
Must I run it in the jar file deployed to appServer?
it's very inconvenient!
Thanks!!

Hello
Inline there are the answers
[email protected] (Grand Gana) wrote:
Hi !
I want to know how to get the local interface of a session ejb from a
jsp page ???
My session ejb is in a jar, and my jsp page is in a war. (they're not
together in a ear)You cannot call your EJB by a local interface by this way.
The war and the ejb-jar must be in the same ear.
This is due to classloading architecture.
I can have access to a remote interface of an other session ejb from
a
jsp page doing :
     InitialContext ctx = new InitialContext();
     Object objref = ctx.lookup("article.ArticleManagerHome");
     ArticleManagerHome home = (ArticleManagerHome)
PortableRemoteObject.narrow(objref,
ArticleManagerHome.class);
But I can't have access to the local interface from the same jsp page
doing :
     MyManagerLocalHome home = (MyManagerLocalHome)ctx.lookup
("article.MyManagerLocalHome");
I get the following error :
javax.naming.NameNotFoundException: Unable to
resolve 'article.ArticleManagerLocalHome' Resolved: 'article'
Unresolved:'ArticleManagerLocalHome' ; remaining
name 'ArticleManagerLocalHome' This is another problem.
Check the jndi name in the ejb-deployment descriptor or check the jndi on your
server to verify that a local interface implementation has been bound to it.
>
What should I do ???
(I don't want to put them in the same ear)
An EJB reference in the web.xml of my war ??? How ?
A lookup with java/comp/... ??? How ?
I don't understand !!! It's so difficult to do simple things !
Bloody EJBs !!!Noooooo ;)
But I can agree with you on local interfaces ....
The J2EE specs speak about "same virtual machine" ....
But classloading architecture "speaks about" "same classloader" (same ejb-jar)
or "related classloaders" (war and ejb in same ear).
I think something is still missing ....
>
TIA
JCMark

Sub-interfaces on PO

Hi, I have put 2 physicl interfaces (te0/8 & 9) on the ASA-5585 into a PO and am assigning ips/vlans to the sub-interfaces. I have 2 issues: - Why am I not able to ping the other sub-interface from the ASA itself? (I can ping the 1st one), Secondly, why the IPs are not visible in "sh int ip brief" ?Although I can see them in "sh ip" ..
/actNoFailover(config-if)# int po17.100
/actNoFailover(config-subif)# vlan 100
/actNoFailover(config-subif)# ip add
/actNoFailover(config-subif)# ip address 100.1.1.1 255.255.255.0
/actNoFailover(config-subif)# int po17.101
/actNoFailover(config-subif)# vlan 101
/actNoFailover(config-subif)# ip address 101.1.1.1 255.255.255.0
/actNoFailover(config-subif)# int po17.102
/actNoFailover(config-subif)# vlan 102
/actNoFailover(config-subif)# ip address 102.1.1.1 255.255.255.0
/actNoFailover(config-subif)# ping 100.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 100.1.1.1, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 30/32/40 ms
/actNoFailover(config-subif)# ping 101.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 101.1.1.1, timeout is 2 seconds:
/actNoFailover(config)# sh int ip brie
Interface                  IP-Address      OK? Method Status                Protocol
TenGigabitEthernet0/8      unassigned      YES unset up                    up
TenGigabitEthernet0/9      unassigned      YES unset up                    up
Port-channel17             unassigned      YES unset up                    up
Port-channel17.100         unassigned      YES manual up                    up
Port-channel17.101         unassigned      YES manual up                    up
Port-channel17.102         unassigned      YES manual up                    up
Please advise?

Hello Sande,
That is correct! Please mark this question as answered so future users having a similar problem can learn from your
solution.
Regards,
Julio

SGE2000 QoS: Ingress Rate Limit BUG ?

I buyed a new unit of SGE2000. Thirst I changed firmware to newest one (3.0.0.18) so I do not know what firmware was installed before.
The problem is that it is not posssible to change Ingress Rate Limit to value lower than 3500...
Hardware Version
00.00.01
Software Version
3.0.0.18
Boot Version
2.0.0.03
Manual says:
Ingress Rate Limit — Defines the amount of bandwidth assigned to the interface.
For FE ports, the rate is 62 - 100,000 Kbps.
For GE ports, the rate is 62 - 1,000,000 Kbps
====
Default value for Ingress Rate Limit field is 3500, while I change it to eg. 512 the combobox is opening with warning information:
"Entered value in highlighted field must be an Integer. Range 3500...1000000"
"Committed Information Rate (CIR)" field allow to put a value down to 64, so it is ok.
Should I downgrade firmware to v3.0.0.17 ?
Any help appreciated.

My appologies for the lack of reply here. I checked with the PM for the product and they asked me if there is a case open with the Small Business Support Center (SBSC) on this issue. Have you had a case open on this yet? If not can I ask you to log a case and then respond back to this postig with the case number please? It seems this is a bug so the product team will need to process the fix for this via the standard problem identification/case reporting process.
Thanks in advance!

HSRP using sub-interfaces,

I'm planning a design that will need two 2950s to support 4 vlans. Non-local traffic will be routed out via one of two HSRP routers (one pair of vlans using router 1 as a primary, the other pair using router 2).
I've dug around the cisco documentation but can't find an answer to the following...
Does HSRP run ok over sub-interfaces?
For example, VLAN 1 default gateway will be HSRP (virtual) router's f0/0.1 x.x.x.x, VLAN 2 default gateway will be HSRP router's f0/0.2 x.x.x.x, etc.
Any ideas?

Hi Dwatson,
YES, HSRP supports on sub-interfaces also & there wouldn't be any problems.YES the default gateway would be the HSRP standby ip address specified on the sub-interface for the vlans.
eg.
Router A
interface FastEthernet0/0.1
description ***ABC***
encapsulation dot1Q 1
ip address 172.16.1.2 255.255.0.0
standby 1 ip 172.16.1.1
standby 1 timers 5 15
standby 1 priority 108
standby 1 preempt
Router B
interface FastEthernet0/0.1
description ***ABC***
encapsulation dot1Q 1
ip address 172.16.1.3 255.255.0.0
standby 1 ip 172.16.1.1
standby 1 timers 5 15
standby 1 priority 109
standby 1 preempt
Note donot give any ip address on the fastethernet interface.
interface fasthethernet 0/0
no ip address
hope this helps.
rate this post if cleared

WLC 5508 and Anchor/GuestNet rate limit traffic?

Running WLCs 5508s 7.0.116.0 with GuestNet and Anchor setup, how can I limit the bandwidth on the GuestNet SSDI to 2 Mbps, etc?
The DMZ WLC (Anchor) runs thru a ASA 5508 7x, can I rate limit traffic via ASA?

That's really a matter of preference. This document describes things to keep in mind when altering these QoS profile configurations, FYI.
http://www.cisco.com/en/US/partner/docs/wireless/controller/7.0MR1/configuration/guide/cg_controller_setting.html#wp1254532
It really depends on how many guests, what type of traffic, etc, to make a judgement call as to where you should set these. I'm sorry but I don't have any examples from existing configurations, but hopefully the document explains how to best alter these settings.

Can I rate-limit on the sub-interface in cisco asr 1013?

Similar Messages

Maybe you are looking for