Cisco Switching and Apple Computers
I was wondering if anyone has any experience with running Macs' on their Cisco networking equipment. It seems to only be one generation of IMacs' that disable ports on our switches. I do realize many variables may have a role in disabling port settings but it's only a chosen few that it happens with. Not having the authority to program each port being disabled to run in full duplex mode versus default settings from manufacturing in auto-negotiate I'm at a loss. Even after explaining the solution, nothing gets done. My question is could someone post some documentation of some sort backing up my theories? Also if anyone could please include anything about proper port settings for access points on our VLANs that also become disabled at times. I do know through research done that all access points should be classified as such on the network. Am I correct in stating this also? I thank you in advance for any information or help you may provide for me and posts will be rated.
check out the following links, hope this helps :
Using VLANs with Cisco Aironet Wireless Equipment :
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml
Wireless Virtual LAN Deployment Guide :
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
Similar Messages
-
Linksys SLM2005 Switch and Apple Computers HELP!!
I have a MBP 17 inch, MB 13 Inch and and ATV. I have a Linksys SLM2005 Switch. When ever I plug in an apple computer into the switch, it keeps telling me that a cable is disconnected and the port light on the switch will not light up. I can take the same cable to a PC or any other device that is not an apple product, and it will work just fine, lighting up a light and allowing access into the switch.
Can anyone tell me what is going on here?? Why will my Macs not work, I have tried to manually set the ip address as well, to no avail. just keeps acting as though there is nothing connected. I have tried all resets as well. Any help here would be great.
ThanksWhat are you using the switch for?
-
What are the problems associated with Minecraft game and Apple computers
What are the problems with Minecraft game and Apple computers. I've read that the two are incompatible.
You have a very limited amount of time before night falls and the monsters might come out. You have to HOLD DOWN the mouse button to hit things to change them. Hit the earth to dig a cave. Hit a tree repeatedly to get wood.
A two button mouse is superior, because a lot of actions require a left click. <-- OH That is why they say it is not compatible!
It is compatible, you just need to left click sometimes! -
Cisco switches and virtual ip address(load balancing address) on xenapp portals
Hi I am quite new in configuring cisco switches and stumble across an issue after installing xenapp7.6 with load balanced portal to the ddc`s
It seems i only can ping or get access to portal if using real ip address behind cisco switch from other subnets in my network.
I can ping ddc01 and ddc02 and connect to the portal with http without problem. However when i triy to access the load balancing address of the ddc`s
it wont answer to ping or http
In same subnett it is no problem connecting to the load balancing address of the ddc`s, but in loactions on other subnets i only can access real server ip
eks
dd01 192.168.1.4 ok ping and access behind cisco switch from subnets
ddc02 192.168.1.5 ok to ping access behind cisco switch from subnets
load balancing for both ddc 192.168.1.6 not able to get answer og access from subnets, only in same subnett
Is there any way to configure switch to access the load balancing address of the ddc`s ?
Regards
Pål Arne RøbergWrong forum. This forum is dedicated to feedback related to CSC framework itself. You should not wish for response here.
Moved by moderator, no longer apply. -
How to view the login log in window NPS after login cisco switch and without SQL server database
how to view the login log in window NPS after login cisco switch and without SQL server database
in summary
there is only log with event id 4400
A LDAP connection with domain controller XCPAWS20.cyberport.noc for domain NOC2 is established.Hi adil,
For your issue, you can create a custom security token service (STS) and then set up a trust relationship between a SharePoint 2010 farm and the custom STS.
For more information, you can refer to the articles:
http://forums.asp.net/t/1335229.aspx?Sharing+Authentication+Ticket+Between+ASP+NET+and+Sharepoint
https://msdn.microsoft.com/en-us/library/office/ff955607(v=office.14).aspx
http://www.paraesthesia.com/archive/2011/02/01/working-with-windows-identity-foundation-in-asp-net-mvc.aspx/
Best Regards,
Eric
Eric Tao
TechNet Community Support -
Cisco wireless and Apple Mac woes
Hello all,
I've been working with Cisco wireless and WLC's for a couple of years now but the recent onslaught of Apple Mac's is giving me heart burn. I've seen this at numerous sites now and need to throw it to eht community for guidance.
Basically we have had a number of instances where the Macs just fall off the wifi. Sometimes it's when they wake from sleep and other times when roaming between AP's (1131s with same SSID's). Our standard install is WPA2 and per ap local authentication. PC's work fine and never an issue.
We have completed a survey with a spectrum analyser and no RF interefence is present nor errors on the radio interface.
Questions:
- Is there a preferred Cisco config/setup for Mac's to work reliably? I've heard loads of rumors but nothing concrete and nor can I find anything specific.
- Should I be setting up WDS in case there is an authenticating issue.
- For those who are Mac gurus and happen to be reading. What Mac options we should look at?
This has all come to a head because the clients IT company who recommended the Macs (different from us doing the network infrastructure) are insisting that the problem is Cisco incompatibility and that we should rip out the Cisco kit and install airports (what tha!!!).
Thanks in advance for any pointers.
For those who like a config here it is .... Vanilla stuff really
Building configuration...
Current configuration : 2236 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP4
no logging console
enable secret xxxxxxxxxxxxxxxxx
no aaa new-model
dot11 syslog
dot11 ssid Home
vlan 1
authentication open
authentication key-management wpa
guest-mode
mbssid guest-mode
wpa-psk ascii xxxxxxxxxxxx
dot11 ssid avnet
vlan 2
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii xxxxxxxxxxxxxxxx
username abcd password 1234
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
encryption vlan 2 mode ciphers tkip
ssid Home
mbssid
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.10.54 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
no ip http server
no ip http secure-server
bridge 1 route ip
line con 0
line vty 0 4
login local
endYeah!! even i have come across multiple issue with MAC and Cisco.. these are the below settings which i normally do on the cisco gears and most of the times this solved the issue..
on the IOS AP disable Aironet Extentions and set the poer local and ofdm to max
no dot11 extension aironet
power local cck max
power local ofdm max
end
On the WLC, disable Aironet IE..
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull -
Cisco Switches and Dell EqualLogic PS series integration
Scanrio: In head office there is Dell EqualLogic PS series and in branch also same for replicaiotn from head office to branch i want to know the ios feature set of Switch and Router.
If the Dell EqualLogic systems are using iSCSI to communicate there is no specific feature required on the Cisco gear. The Cisco gear will pass iSCSI traffic just like any other IP traffic.
Make sense?
Cheers,
Brad -
Cisco switches and 802.1.x
Hi, there !
I have a question for you.
Cisco all switches, is it impossible to present for 802.1x ?
I try to put a network access server in our network to authenticate.
Thanks.
I will wait your answer.
Regards.Most Cisco switches will handle 802.1x, but it depends on the switch and the OS. Which specific ones are you considering?
Wes -
OK, Just bought the new WRT 300vl wireless broadband router.
I accessed the router through a direct ethernet connection the web base way.
Tried to set up the router using the url way but am getting no
where, it acknowledges that I am conversing with the router on settings, but when I try to connect to the internet my powerbook says I am not connected. I am using safari, but I read in some help section that I must use Microsoft internet explorer in order for this router to be set up properly?
Does Linksys have a setup/help guide for apple computers using OSX?
It says on one pdf that it is compatible with MacIntosh computers
but really,
when did Apple last produced a Macintosh?
I have an apple powerbook not a Macintosh powerbook.
Should I take this router back to the store and find
a wireless N router brand that is more compatible with
Apple computers?
I am sorta in a fix because my old wireless
hub went out and I also rely on my VOIP phone to communicate.
I am currently using a neighbors computer to relay this message.
help and
Thanks.All faqs and knowledge base articles from linksys are on the linksys support pages. There should be something for macos, too, I guess.
I wouldn't worry about the naming "Macintosh". Apple changed the names so often you'll find the weirdest things those requirement sections at times. The router will work fine with a computer running macos. I had never problems running my iMac through a RV042 or WRT54G, wired or wireless.
To figure out what the exact problem is: could you please check the Status tab on the router configuration? Post the status output please. Also, if it is unconnected there, press the connect button and post the exact error message you get if you get one.
If you are connected on the Status page, please also try a ping command in a "Terminal" window. Lookup the gateway and DNS server ip addresses on the status page. Then ping those ip addresses, e.g.,
ping 123.234.211.121
Post if it succeeds or the exact error message if not. -
Cisco Switches and HP Interoperability with Spanning-Tree (RSTP)
Hello All.
I read a lot of information from this forum about Spaning-Tree interoperability between HP Switches and Cisco Switches.
Rather than having questions I would like to post that I manage to configure successfully HP and Cisco using RSTP (802.1w).
SWPADRAO]display stp root
MSTID Root Bridge ID ExtPathCost IntPathCost Root Port
0 32768.cc3e-5f3a-2939 0 0
[SWPADRAO]display stp brief
MSTID Port Role STP State Protection
0 GigabitEthernet1/0/47 DESI FORWARDING NONE
0 GigabitEthernet1/0/48 DESI FORWARDING NONE
[SWPADRAO]display stp instance 0
-------[CIST Global Info][Mode RSTP]-------
CIST Bridge :32768.cc3e-5f3a-2939
Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC :32768.cc3e-5f3a-2939 / 0
CIST RegRoot/IRPC :32768.cc3e-5f3a-2939 / 0
CIST RootPortId :0.0
BPDU-Protection :enabled
Bridge Config-
Digest-Snooping :disabled
TC or TCN received :17
Time since last TC :0 days 0h:1m:52s
SWNHAM17#show spanning-tree VLAN0001
Spanning tree enabled protocol rstp
Root ID Priority 32768
Address cc3e.5f3a.2939
Cost 4
Port 26 (GigabitEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 61441 (priority 61440 sys-id-ext 1)
Address 001b.54db.7200
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 Interface Role Sts Cost Prio.Nbr Type
Gi0/1 Altn BLK 4 128.25 P2p
Gi0/2 Root FWD 4 128.26 P2p
SWNHAM18#show spanning-tree VLAN0001
Spanning tree enabled protocol rstp
Root ID Priority 32768
Address cc3e.5f3a.2939
Cost 4
Port 26 (GigabitEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 61441 (priority 61440 sys-id-ext 1)
Address 001b.0cbc.4300
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 Interface Role Sts Cost Prio.Nbr Type
Gi0/1 Desg FWD 4 128.25 P2p
Gi0/2 Root FWD 4 128.26 P2pHello, David.
Your command doesn't work because it's made only for tha ports that has command "spanning-tree portfast" in them. Try change spanning tree mode at the HP switch to MSTP if this is possible. -
Cisco Valet and Apple TV2 problem.
I just installed a new Cisco Valet router, and though my lap and desktops work fine, I'm unable to get past the "setting time and date" notification when trying to wirelessly connect my Appletv. I tried rebooting the module, but even after waiting considerable time, I simply end up with the screensaver. Any suggestions would be appreciated from this new member
BobWhat is the answer to that problem? I have a cisco router and have the same issue. Thanks
-
Cisco Aironet and Apple Airport - Pb with roaming
Hello,
I'm having a problem with roaming between one Cisco Aironet 1232AG AP and one Airport Extreme basestation. Both AP are on the same subnet, hidden network and WEP 40bits.
0->Cisco->Apple->Cisco->....... works fine
0->Apple->Cisco doesn't works
0-> means Pwk restarted
Any clues?
ThanksNo. I tried with both AP on the same channel or on a different channel same issue. Also, same problem with WEP 128bits. However the issue disappears with WPA personal (TKIP or AES-CCMP)
-
How to set up Qos for Microsoft Lyncs 2013 in cisco Switches and Router
Hi
as i am new to Qos part , please send the complete qos configuration command has to apply in my cisco 2960s switchs as well as 4506 chassis(L3 mode act as my router).
as i know from microsoft, DSCP 46 and 34 should give highest priory
please send the completed configuration for priorities this DSCP
thanks
SujishHi,there,
The rule setting should be same as in Exchange 2010,you can configure it via outlook or OWA if you have full access permission. I also believe it should be something related to Repliation,would you please check the event log to see if the
AD and Exchange replication has completed.
In some cases, replication can take longer depending on how many AD sites and Exchange servers in the environment:
http://support.microsoft.com/kb/148381
http://support.microsoft.com/kb/158989
Hope these useful!
Regards,
Sharon
Sharon Shen
TechNet Community Support
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. -
Palm devices and Apple computers
I was thinking about getting a palm T5 and I was wondering how well palm devices work with macs. Does the iCal sync ok and everything else (i know there is a palm desktop version for mac but i do not want to use that, i like ical to much) so does iCal sync fine and how about other apps, can they sync with my palm, Mail? Address book? etc....
Thank you,
TMThanks, Wade. I didn't know that.
I've actually already installed the Palm Desktop software, so does this mean I'm good to go?
I realize this sounds pretty clueless, but I must confess that's how I am when it comes to this new phone/pda. I've also never used iSync before. In fact, until you mentioned it, I didn't even know it was installed.
I just opened iSync for the first time and tried to sync up with my Treo via bluetooth, and it found the device (very cool!) but was unable to sync. I got a message saying "iSync can not connect to this device."
When I tried to pair the device using the bluetooth setup assistant, it found the device, but all the boxes were grayed out and it said that "there were no supported services found on your mobile pphone."
Any idea what I'm doing wrong. -
Icuii and Apple computers.
Hi,
I wanted to know if we can run the IcuII video conference program on an Imac ?
Thank you for your help.
DGmaestro.Based on their website, it appears this application is compatible with Windows only.
Maybe you are looking for
-
How to run a Java applet on a website.
Hi, I am trying to run the code below [DrawLines.java|http://www.dgp.toronto.edu/~mjmcguff/learn/java/01-drawingLines/] import java.applet.*; import java.awt.*; public class DrawingLines extends Applet { int width, height; public void init() {
-
Retiming with same number of frames
Hi (couldn't find this) - If I want to convert my source video to a new frame rate -- but keep exactly the same number of frames -- what is the best way to do that? Do I just set my desired frame rate in the Encoder tab and then set duration to 100%
-
Table in header (new Pages)
Hi, One year ago I create letterhead paper in Pages. Now, when I open in new Pages I can't see header. So I make new table, texts and when I want copy to header- table is deleted. Any ideas?
-
Transparency Issues When Printing Illustrator File
I'm having a problem when I print a PDF or an AI file, a black box shows up around the transparent figure in the left corner. I've tweaked all of the transparency flattners to no avail. When I export as a JPEG the box isn't there. Its just driving me
-
"Write to measurement file" express VI (TDMS foormat) keeps file opened
Hello! I am trying to use "Write to measurement file" express VI to write TDMS data obtained from DAQmx in LV2011. Each run of the same write function creates new file. It seems that last written file remains to be opened until program stops or next