Cisco Unity playing closed message

Hi everyone, our Cisco 3800 went down this morning and after powering back up the time was off by 30 minutes or so. I have corrected the time but the system insists on playing the closed message and we are not closed. I cannot get a hold of anyone at our provider's office. There has to be an easy fix for this. Any advice?
This topic first appeared in the Spiceworks Community

The System Call Handler has an attached active schedule, where I marked the open hours. So I can differ between open/closed hours transfer rules.
The restriction tables are ok.
Do you mean the CSS of the CTI Route Point directory number? If so, then yes.

Similar Messages

What Greeting does unity play when it encounters a Holiday

If we have a check mark in "Observe Holidays" what gretting will unity play when it encounters a Holiday?

Hi Dustin,
Holiday Settings
When a Holiday setting is in effect, Cisco Unity plays closed greetings and observes closed transfer rules.
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_administration_guide_chapter09186a0080443b5e.html#wp1548625
Setting up a Holiday Greeting for Cisco Unity
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_tech_note09186a008011aa09.shtml
Hope this helps!
Rob

Cisco Unity Express - No Audio on Every 4th Message

Hi everyone! New to the site and pretty new to Cisco phone systems. I am supporting a Cisco Unity Express Ver. 3.1 system that has an odd problem and I cannot find the same problem anywhere so thought I would ask here. On every 4th call when you leave a message there is no audio. There is just dead air and the duration of silence is as long as you talked in the message. This happens with all calls internal and external. We have 12 ports and it is not port specific. For example port 602 is fine 3 out of 4 calls, but port 610 may be bad 2 out of 4 calls. The only pattern is every 4th call the message left is dead air when playing back from the phone and the email attachment. Any chance there is some magical checkbox out there that I need to check!?

Update CUE software and check again.

Cisco Unity 7 Problem in Message Store Wiard. Showing some SRV Records Missing in DNS Table. Please suggest and help on this matter.

Installed Cisco Unity 7 on Windows Server 2000 and Unity Server is on Domain,and Exchange we are using is Exhcnage 2007. When we reach at Message Store Wizard it is showing some error at the end that " Failed reaching for Unity in Active Directory Global Catalog. The SVR Record may be missing in DNS Table" . It shows when we slected Exchange in Process and the Selected Storage Group. And the it takes time and then shows error. Please try to resolve this issue soon, we need this solution urgently. We have already spent several days on different issues regarding Unity.
If you need to talk regarding this matter, Please contact on +919780660619, and the conatct person name is Manav.
Thanks in Advance
Rosy

Rosy,
We cannot call you from this forum. If you truly need a call, you can open a TAC case. The info I can tell you is that you need to fix this in your dns. A simple google search of "no SRV record Windows 2000 server" comes up with numerous resources that can help you fix this. Here is just one example.
http://support.microsoft.com/kb/241505
and
http://www.petri.co.il/active_directory_srv_records.htm
I would also advise you, if you are doing a new install with Unity 7 and that version of Exchange, that you use Windows 2003 as the OS. Even MS doesn't support Windows 2000 Server any more so if you end up having an OS issue on your Unity server, we will not be able to get MS to help you. From a support perspective, I would advise you to use Windows 2003 Server in this implimentation.
Thanks!
Tray

Cisco Unity Connection 8.5 Single Inbox - Unified Messaging?

For the Cisco Unity Connection 8.5, to enable Single inbox unified messaging do we need to get additional licensing for this feature?

Hi Ali,
LicIMAPSubscribersMax
Users with IMAP access to voice messages or with single inbox (single inbox available in Connection 8.5 and later only)
Sets the maximum number of users who can use:
•A third-party IMAP client to access voice messages.
•The unified messaging feature "Synchronize Connection and Exchange Mailboxes (Single Inbox)" on the Unified Messaging > Unified Messaging Services page and on the Users > Users > Unified Messaging Accounts page.
For single inbox, the total number of users in classes of service for which single inbox is enabled must not exceed the licensed maximum. This applies regardless of the number of users in those classes of service who are configured to use single inbox. In addition, all users who are configured for single inbox must be in a class of service for which single inbox is enabled.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/administration/guide/8xcucsag310.html
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

Unity 5.0.1 pin error playing failsafe message

Hi
I have a Unity 5.0.1 ES86. Whenever a subscriber enter a wrong PIN system play failsafe message
“This system is temporarily unable to complete the call, call again later” and disconnects.
Thanks

This problem occurs when using a language other than US english , switch back to US(english ) and see if the problem persist
For any other language contact TAC , and they will provide with a non Unity patch (#99)

Cisco Unity Express 8.6.6 Voice Mail not deleting when e-mail with attachment deleted

I have a Cisco Unity Communications Manager rel 9.1.2 that supports a remote location with a Unity Express rel 8.6.6 voice mail service module in the voice gateway to insure if WAN goes down the location still has voice mail. We have Voice Mail to E-Mail working. The problem is that when the e-mail with the voice mail is deleted the message stays in the Unity Express Voice Mail Box. All of our local users on the same Call Manager Cluster using a local Unity Connection Cluster rel 9.1.2 have the voicemails deleted when the e-mail is deleted.
How can I resolve this issue?

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Voice mail is not stored in cisco unity 7.0(2)

We have configured exchange2003 and cisco unity in the same MCS(7845 IBM) box. We have done with integrating it to CCM 7.1.3 using SCCP. When we make a call from sub A to sub B, if sub B doesnt answer the call it is forwarded to Cisco Unity and the greetings are played. when we tried to record the message and play back it is not played back also when we send that message, message is not reaching sub B (phone keypresses are taken). Please any one help me to solve this issue.
Thanks,
Nithiya.

Adding Languages
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/upgrade/guide/ex/5xcuruge030.html#wp1104842
If the other question is about an AA all you need is a CTI RP with CFA to VM, a call handler with matching DN and record the greeting.
If you need more options configure new call handlers and use the caller input config from the first call handler.
HTH
java
If this helps, please rate
www.cisco.com/go/pdihelpdesk

Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

Hello,
Currently Running:
Cisco Unified Communications Manager 8.6.2
Cisco Unity Connection 8.6.2
Problem:
when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
I also have the message relaying to my E-mail and I get the same in the subject line.
"Message from Cisco Unity Connection Messaging System (Unknown extension)"
This tends to be a big deal with the Sales team as customers will call and say "Call me back"
But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
Any help will be appreciated.
Thanks
Tim

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Unity 5.0(1) System error when calling into CUGA (Cisco Unity Greetings Administrator)

When I call into CUGA (Cisco Unity Greetings Administrator), I get a failsafe message and the system hangs up. The below events are written in EventViewer. GUSI and AvCsMgr Diags attached.
Any help would be much appreciated.
Event Type: Error
Event Source: CiscoUnity_Miu
Event Category: Error
Event ID: 531
Date: 5/28/2011
Time: 5:23:51 PM
User: N/A
Computer: NYLCNJUN01
Description:
Cisco Unity's telephony component has encountered a serious error.
EXPLANATION:
A serious failure has occurred on port 53 while trying to open a wav file or stream. Depending upon the severity of the failure, parties on this call could experience unexpected behavior or be disconnected. In some cases, further calls on this port will not be handled correctly.
TECHNICAL DETAILS:
Thread 0x00002220 had a failure on port 53 in method CAvMiuWave::GetLength()
DESCRIPTION: AvWav WavOpenEx2 failed with 0x00000000.
DETAILS:
FileName: Welcome.
CALLINFO:
CallerID: 2003406
CalledID: 3007910
RedirectingID: 3007910
Origin: Internal
Reason: FwdUncond
Trunk: 0.
CALL SEQUENCE:
[15:17:29:794 - 0x00002100] Drop() - S_OK
[17:23:51:209 - 0x00001D6C] LINE_APPNEWCALL(0x000115D3)
[17:23:51:209 - 0x00001D6C] SetEvent(NewCall)
[17:23:51:209 - 0x00001D6C] SetEvent(CallInfoArrived)
[17:23:51:302 - 0x00002220] Answer() entered
[17:23:51:302 - 0x00002220] lineAnswer(0x000115D3) - 0x00011439
[17:23:51:302 - 0x00001D6C] LINE_REPLY(0x00011439 | 0x00000000)
[17:23:51:427 - 0x00001D6C] StopIO(TERM_REPLAY) entered
[17:23:51:427 - 0x00001D6C] StopIO(TERM_REPLAY) - S_OK
[17:23:51:427 - 0x00001D6C] LINECALLSTATE_CONNECTED(0x000115D3 | Active)
[17:23:51:427 - 0x00002220] WaitFor(0x00011439 | CONNECTED) - CONNECTED
[17:23:51:427 - 0x00002220] Answer() - S_MIU_CONNECTED
[17:23:51:427 - 0x00002220] GetMediaLength() entered
[17:23:51:427 - 0x00002220] WavOpen(Welcome) - 0x00000000
[17:23:51:427 - 0x00002220] GetMediaLength() - 0 | E_FAIL
[17:23:51:427 - 0x00002220] Play() entered
[17:23:51:443 - 0x00002220] WavOpen(Welcome) - 0x00000000.
Event Type: Error
Event Source: CiscoUnity_Wav
Event Category: Error
Event ID: 807
Date: 5/28/2011
Time: 5:23:51 PM
User: N/A
Computer: NYLCNJUN01
Description:
Cisco Unity's multi-media component has encountered a serious error.
EXPLANATION:
A serious failure has occurred on port 53 while opening an audio stream. Depending upon the severity of the failure, parties on this call could experience unexpected behavior or be disconnected. In some cases, further calls on this port will not be handled correctly.
TECHNICAL DETAILS:
Thread 0x00002220 had a Failure on Port 53 in AvWav
DESCRIPTION:
File: H:\views\CUESB1_view\un_Miu\UnityAvWav\WAV.cpp(1095)
Method: WavOpenEx
Failure: call to mmioOpen(Welcome) failed(101).

Tommer,
I found the issue that caused problem.
One of the Unity Admins (hand slapped) used RDP in Console mode which redirected the custom wave driver. This is a known issue with using RDP in Console mode in Windows 2003. There is a MS Hotfix 928046 that should have prevented this from happenning, but it was alraedy installed. A Server reboot cleared the condition and its all working again.
Thanks for the reply.

Cisco Unity - Greeting settings

Hello,
I have the following situation, a manager will forward his phone to his assistent. His assistent has her phone "Forward All" to Voicemail. But when they do this they hear the standard unity greeting and not the personal greeting.
I've checked in the greetings settings and activated the internal one , but that doesn't seem to work.
The only way we can get this to work is to put the full e.164 number in the forward, it seems to trick the unity to act as a external caller.
Kr,
Yannick

Hi,
the "Forwarded Route" was no good, that seems to edit the option for everyone
So we have 2 phones:
Phone 1: Manager number 1234
Phone 2: Assistent number 1235
Phone 1 is forwarded to Phone 2 in a "Call Forward All" to "1235, at this time Phone 2 has a call forward all to the voicemail checkbox
From the moment someone calls Phone 1 he is directly transferred towards Phone 2, Phone 2 is also forwarded to voicemail, so the original caller will reach the voicemail of Phone 2, but the original caller doesn't hear the personal greeting, he hears the standard cisco unity message of: "Hello , Welcome to cisco unity, from a touch dialpad ......, and we want it to just play the self recorded greeting of the user of Phone 2

Cisco Unity 7: Voice mail cann't get the name or Number phone of the caller

Hi,
I have installed Cisco Unity Messaging Unified version 7 and integrated with Exchange 2010.
I have two scenario, and I want to know if are normal or not:
1. If the 2 IP phones are subscribed with Cisco Unity: the first IP phone call the other IP phone and let a voice mail. When the second IP phone check his message vocal it can get the name of the caller or his number phone (the message is: You have One message from XXXX) and he get e-mail as objet: Voice Mail from XXXX.
2. If one IP phone is not subscriber with cisco unity call other Ip phone subscribed with cisco unity and let him a voice mail. The second IP phone when check his message vocal it can’t get the name of the caller or his number phone: The message is: You have one voice mail xxxx; without indicate from!! and he get a e-mail as object: Voice mail from Unknown.
Please, I want to know if the second scenario is normal ? if not, who to resolve this problem? I want that he indicate the number of caller same he isn't subscriber with cisco unity?
Thanks a lot,
Best regards,
Omar YUNSI

So for the 2nd scenerio you would want to check what your Message Subjects were set to. For Unity 7 open Web SA, click Configuration and then Message Subjects. Make sure that the Outside Caller Message has %CALLERID% in it somewhere. The value %CALLERNAME% will return unknown if we do not receive a name from the PSTN.
Try setting the Outside Caller Message to:
%U% %P% Voice Message from %CALLERID%
and that should get you your desired results.
The default Message subject is:
%U% %P% Voice Message from %CALLERNAME% (%CALLERID%). So with that it would say Voice Message fom Unknown (xxxx) if it was not able to determine the name of the user which is usually normal from a PSTN call.
Just to note, the From address is always going to say from Unity Messaging System, it will only be the subject that has the extension in it.
Bryan

Unable to create a notification for a group (Cisco Unity Express 3.2)

There is Cisco ISR 2821 with CME 7.1 and Cisco Unity Express 3.2.
I am trying to create notifications for a group named AAA in CUE.
I do following (GUI):
1. Go to Configure -> Groups
2. Click on the group name AAA.
3. In Group Profile window 'Enable notification for this user/group' option is enabled.
4. Go to Mailbox tab. There is an associated mailbox with ticks against Enabled and Fax Enabled.
5. Go to Notification tab and see the warning:
No Notification Devices found for User/Group
Also, there are another several groups on this system and I am able to turn notification on for them. These groups have the same owners and members that AAA has. Moreover, if I create a new group and set it up absolutely the same as AAA, I can turn notifications on for it.
The problem in this way is that we have our custom greetings and after I created a new group, for example BBB, with the same settings (as AAA, inluding Primary Extansion and Primary E.164 Number) and remove these numbers from AAA, then it works and users would receive notification about new voice messages. BUT, when I call BBB I listen to standart Cisco greeting promts.
I don't undestand why it happens, because all these greetings are determined in Voicemail -> Auto Attendant section and I did not any changes here at all.
How can I fix this 'notification' problem?
Thanks.

Process with success:
unzip the packet in: C:\APEX
1. Install:
@apexins SYSAUX SYSAUX TEMP /i/
2. Change to password:
@apxchpwd,
3. Run apex_epg_config.sql
On windows:
@apex_epg_config.sql (page 30, the guide of intallation)
Important:Replace SYSTEM_DRIVE:\TEMP by C:
E.g.: @apex_epg_config C:
After this, follow the next steps
4. ALTER USER ANONYMOUS ACCOUNT UNLOCK;
Finish! Just execute apxldimg.sql script if you is upgrading from a preview release.
Now try the connect on the browser IE6 o later:
http://localhost:8080/apex/apex_admin
Then create your workspace.
Edited by: [email protected] on 10/03/2009 11:59

Cisco Unity Connection 8.5.1 SU3 to 8.5.1 SU6 & Upgrade to 9.1.2

Two questions !
Firstly - I am upgrading to the latest patch level as I want to upgrade the systems to 9.1.X
I am installing UCSInstall_UCOS_8.5.1.16900-6.sgn.iso onto the inactive partition on the publisher then onto the inactive partition on the subscriber.
Then I plan to switch versions out of hours.
Question - will messages / data that has happened between the installation on the inactive partition and the switch version be preserved ??
So if I install onto the inactive partition at 1pm, then an important message is left at 2pm and I switch version at 3pm, does the iimportant message exist on the active partition at the end ??
Second question -
I have UCCX-8.5.1 SU4 (HA), CUC 8.5.1 SU6 (HA) and CUCM 8.5.1 SU6 (1 pub, 2 sub) - so 7 VM's in total.
If I want to migrate to -
UCSInstall_UCOS_9.1.2.12900-11.sgn.iso & UCSInstall_UCCX_9_0_2_UCOS_9.0.2.11002-27.sgn.iso
in which order should the installations take place ?? CUCM Publisher last ?? Publisher first ??
Thanks
James

Hi James,
+5 to my friend Aman for his good tips here
Messages are preserved during the "switch-version" so the messages left before the command is run will be preserved as they are stored in a "common" partition;
Switching to the Upgraded Version of Connection 8.x Software
If you chose not to automatically switch to the upgraded partition at the end of the upgrade, do the following procedure when you are ready to switch partitions.
To Switch to the Upgraded Version of Connection 8.x Software
Step 1 If you do not have a recent backup, back up the server by using the Disaster Recovery System. For more information, see the Disaster Recovery System Administration Guide for Cisco Unity Connection Release 8.x athttp://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/drs_administration/guide/8xcucdrsag.html.
Step 2 Sign in to Cisco Unified Operating System Administration.
Step 3 From the Settings menu, select Version.
Step 4 On the Version Settings page, select Switch Versions, and the following occurs:
•Connection services are stopped.
•Data from the partition where the older version is installed is copied to the partition where the newer version is installed. If changes to the database schema require updates to the format of data, that occurs in this step. Note that messages are stored in a common partition, so they are not copied.
•The Connection server restarts and switches to the newer version.
Note You can check the status of the installation of the upgrade software by using the CLI command show cuc version. The upgrade is complete when the inactive partition has the upgraded software and the active partition has the old software.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/8x/upgrade/guide/8xcucrugx/8xcucrug009.html#wp1056720
The upgrade order is shown here (above link) as well, which is Pub followed by Sub;
Task List for Upgrading Connection 7.x or 8.x Software to the Shipping 8.x Version in a Connection Cluster
Cheers!
Rob

Issue on Cisco Unity Connection after performing 'utils ntp restart'

Hello everybody.
There's a client with Cisco Unity Connection 8.5.1.10000-206. After doing a 'utils ntp restart', the following message showed up:
Communication is not functioning correctly between the servers in the Cisco Unity Connection cluster. To review server status for the cluster, go to the Tools > Cluster Management page of Cisco Unity Connection Serviceability.
The client states that there was no service for 5 minutes and wants to know if performing this task shoud be disruptive or not and if there is any official document from Cisco stating this.
See SrvConnUnity_1.jpg sent by the client after performing the ntp restart.
Right now the service is normal (see SrvConnUnity_2.jpg attached). The client also sent a 'utils ntp
status':
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
synchronised to local net at stratum 11
   time correct to within 12 ms
   polling server every 64 s
Current time in UTC is : Fri Apr 26 16:01:23 UTC 2013
Current time in America/Argentina/Buenos_Aires is : Fri Apr 26 13:01:23 ART 2013
admin:
Could anybody help me with this? What steps should I take? Many thanks in advance.
Best,
Patricio

Hello Patricio,
On the command line guide you won't see any downtime requirements for the Unity Connection server:
Command Line Interface Reference Guide for Cisco Unified Communications Solutions Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/8_5_1/cli_ref_851.html
Utils ntp restart
This command restarts the NTP service.
Command syntax
utils ntp restart
Parameters
None
Requirements
Command privilege level: 0
Allowed during upgrade: Yes
Also on the caveats i do not see any particular mention for this: (Caveats could be found applicable to CUC)
Release Notes for Cisco Unified Communications Manager Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/rel_notes/8_5_1/cucm-rel_notes-851.html
Breaking up the output of the "utils ntp status" there are are two considerations:
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
First, you are using the ip address 127.127.1.0 which is the referenced used for the local system clock, the asterisc means is the preferred option as there is no other IP available. This is not a good practice and not recommended.
Secondly the stratum is unreliable, meaning too high to reach or too low to be accepted by Unity Connection.
If you would happen to run 'utils diagnose test' you would have probably seen an output as the following example below:
admin:utils diagnose test
Log file: platform/log/diag1.log
Starting diagnostic test(s)
===========================
test - disk_space          : Passed (available: 25680 MB, used: 7849 MB)
skip - disk_files          : This module must be run directly and off hours
test - service_manager     : Passed
test - tomcat              : Passed
test - tomcat_deadlocks    : Passed
test - tomcat_keystore     : Passed
test - tomcat_connectors   : Passed
test - tomcat_threads      : Passed
test - tomcat_memory       : Passed
test - tomcat_sessions     : Passed
test - validate_network    : Reverse DNS lookup missmatch
test - raid                : Passed
test - system_info         : Passed (Collected system information in diagnostic log)
test - ntp_reachability    : Passed
test - ntp_clock_drift     : Passed
test - ntp_stratum         : Failed
The reference NTP server is a stratum 11 clock.
NTP servers with stratum 5 or worse clocks are deemed unreliable.
Please consider using an NTP server with better stratum level.
Please use OS Admin GUI to add/delete NTP servers.
skip - sdl_fragmentation   : This module must be run directly and off hours
skip - sdi_fragmentation   : This module must be run directly and off hours
test - ipv6_networking     : Passed
And on the RTMT (Real Time Monitoring Tool) you would have seen a Critical event:
Condition:
The best external NTP server, , is stratum , which is unacceptably high. External NTP servers must be <= strata 8 and should be <= strata 5. NTP server strata can be verified using the CLI 'utils ntp status' command ('st' column). Try using different NTP servers.
Problem cause:
All specified external NTP server(s) have unacceptably high stratum values. Network issues exist or the designated servers have unreliable stratum values.
Information is self explanatory and therefore reassures the need of having a NTP different from the server itself.
By the snippet you sent we can know that it is the publisher server, as the Subscriber polls this information from the Publisher.
Installing the Operating System and Cisco Unity Connection 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/installation/guide/8xcucig020.html
"Cisco recommends that you use an external NTP server to ensure accurate system time on the publisher server. Ensure the external NTP server is stratum 9 or higher (meaning stratums 1-9). The subscriber server will get its time from the publisher server"
Documentation also reaffirms the need for that NTP to be accessible otherwise your system can be degraded. Some addtional information which would be interesting to know is:
- Why did they had to restart the NTP in the first place?
System Requirements for Cisco Unity Connection Release 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/requirements/8xcucsysreqs.html
"A network time protocol (NTP) server must be accessible to the Connection server"
On the Cisco Unity Connection Serviceability> Tools> CLuster Management screen shot you sent i see that the ports were "Not Available" and that the customer stated "there was no service for 5 minutes".
By no service did they mean that over the phone they heard a disconnected tone or a failsafe message?
Additionaly after the servers resolved from SBR the Subscriber never recovered entirely as it did not start the Conversation Manager service.
Bottom line if they are able to reproduce it then it would be worth a while checking with TAC
Best regards,
David Rojas Peck
Cisco TAC Support Engineer, Unity
Email: [email protected]
Mon, Wed, and Fri 12:00 pm to 9:00 pm ET, Tue and Thu 8:00 am to 5:00pm ET
Cisco Worldwide Contact link is below for further reference.
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html

Cisco Unity playing closed message

Similar Messages

Maybe you are looking for