Connection at system start

Hi,
since system upgrade (about 2 weeks ago) i have problem with estabilish internet connection at system start.
To connect i have to:
ifconfig ra0 10.14.1.4 broadcast 10.14.1.255 netmask 255.255.255.0
iwconfig ra0 essid WiNet-AP14 mode 2 channel 7
but, even before it iwconfig and ifconfig looks ok:
iwconfig:
ra0 RT2400PCI ESSID:"WiNet-AP14"
Mode:Managed Channel=7 Bit Rate:11 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
ifconfig:
ra0 Link encap:Ethernet HWaddr 00:0C:76:CA:85:7C
inet addr:10.14.1.4 Bcast:10.14.1.255 Mask:255.255.255.0
inet6 addr: fe80::20c:76ff:feca:857c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17 Base address:0x4000
any ideas?
/etc/rc.conf and /etc/conf.d/wireless seems to be fine.
i'm using card with rt2400 chip. drivers from http://rt2x00.serialmonkey.com/wiki/ind … =Main_Page (i tried with beta and daily)
sorry for my english.
Last edited by edpl (2007-06-21 12:57:34)

in /var/log.everything.log
i found line:
Jun 22 13:57:45 skrzynia ra0: no IPv6 routers present
and in messages.log:
Jun 22 13:59:50 skrzynia ***RT2400***: !!! MLME busy, NIC will be reset!!!
Last edited by edpl (2007-06-22 13:22:24)

Similar Messages

TS1567 My apple iphone is not getting started and i can find only apple logo when connected to system\

apple phone 3g is not getting started and i can find only apple logo when connected to system and my system is not recognizing the mobile device. kindly help me in this regard

Put the device in DFU mode (google it) and restore as new.

OSX Mavericks Wifi connection problem when system starts

My macbook pro unable to connect to the preset wifi when system started, same whether starts and ready from sleep-mode, or previous shutdown mode.
This starts to happen just several weeks recently.
However, after restart the entire OSx, the connection (auto detect and connect) would be back to normal.
What's wrong? and any idea to solve this problem? Restart the OS takes very long time, and I don't like to waste time everytime open the laptop.
Please help. Thanks.

Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Wireless Diagnostics - About
Also try turning off Bluetooth

STARTSAP_NBAS - status NO SYSTEM START

Hi all,
I'm upgrading R/3 4.7 to ERP 6.0 SR3 NUC; Windows 2008 + SQL Server 2008. I'm in weekend downtime. In phase status STARTSAP_NBAS I have the error:
UPGRADEPHASE STARTSAP_NBAS
...started at 20140222060031
# Reading Parameter File "D:\usr\sap\put\bin\ALPALL.LST" at 20140222060031
..finished at 20140222060636 with status NO SYSTEM START.
...begin dialogue at 20140222060636
tp.ECO log:
SAPup> Starting subprocess tp.exe with id 5024 at 20140222061006
EXECUTING D:\usr\sap\<SID>\SYS\exe\run\tp.exe pf=D:\usr\sap\put\bin\SHADOW.TPP unlocksys <SID>
Environment: dbms_type=mss
Environment: dbs_mss_schema=<sid>
initial value of NLS_LANG: '<NULL>'
This is D:\usr\sap\<SID>\SYS\exe\run\tp.exe version 372.05.88 (release 700)
Warning: Parameter INTERRUPT is no longer used.
Warning: Parameter DAYLIGHT_SHUTDOWN is no longer used.
Warning: Parameter WITH_TACOB is no longer used.
Warning: Parameter IMPDP_BY_EVENT is no longer used.
Warning: Parameter INTERRUPT is no longer used.
Warning: Parameter DAYLIGHT_SHUTDOWN is no longer used.
Warning: Parameter WITH_TACOB is no longer used.
Warning: Parameter IMPDP_BY_EVENT is no longer used.
TRACE-INFO: 1: [     dev trc,00000] Sat Feb 22 06:10:08 2014                                                         2182 0.002182
TRACE-INFO: 2: [     dev trc,00000] DlLoadLib success: LoadLibrary("dbmssslib.dll"), hdl 0, addr 0000000187740000
TRACE-INFO: 3:                                                                                                           10 0.002192
TRACE-INFO: 4: [     dev trc,00000]      using "D:\usr\sap\<SID>\SYS\exe\run\dbmssslib.dll"                                9 0.002201
TRACE-INFO: 5: [     dev trc,00000] Thread ID:5516                                                                   1590 0.003791
TRACE-INFO: 6: [     dev trc,00000] Thank You for using the SLODBC-interface                                           11 0.003802
TRACE-INFO: 7: [     dev trc,00000] Using dynamic link library 'D:\usr\sap\<SID>\SYS\exe\run\dbmssslib.dll'              19 0.003821
TRACE-INFO: 8: [     dev trc,00000] dbmssslib.dll patch info                                                           40 0.003861
TRACE-INFO: 9: [     dev trc,00000]    SAP patchlevel 0                                                                 9 0.003870
TRACE-INFO: 10: [     dev trc,00000]    SAP patchno 353                                                                  8 0.003878
TRACE-INFO: 11: [     dev trc,00000]    Last MSSQL DBSL patchlevel 0                                                     11 0.003889
TRACE-INFO: 12: [     dev trc,00000]    Last MSSQL DBSL patchno         350                                               9 0.003898
TRACE-INFO: 13: [     dev trc,00000]    Last MSSQL DBSL patchcomment Work process can not be cancelled (1740162)         12 0.003910
TRACE-INFO: 14: [     dev trc,00000] lpc:(local) connection used on SAP<SID>                                             534 0.004444
TRACE-INFO: 15: [     dev trc,00000] ERROR: -1 in function ExecuteAndFlush (SQLExecDirect) [line 5520]               78212 0.082656
TRACE-INFO: 16: [     dev trc,00000] (15157) [42000] [Microsoft][SQL Server Native Client 10.0][SQL Server]Setuser failed because of one of the following reasons: the database principal '<sid>_shd' does not exist, its corresponding server principal does not have server access, this type of database principal cannot be impersonated, or you do not have permission.
TRACE-INFO: 17:                                                                                                           29 0.082685
TRACE-INFO: 18: [     dev trc,00000] <if user_name() != '<sid>_shd' setuser '<sid>_shd'> failed -- connect terminated       32 0.082717
TRACE-INFO: 19: [    dblink ,00433] ***LOG BY2=>sql error 15157 performing CON [dblink#8 @ 433]                       57 0.082774
TRACE-INFO: 20: [    dblink ,00433] ***LOG BY0=>Setuser failed because of one of the following reasons: the database principal '<sid>_shd' does not exist, its corresponding server principal does not have server access, this type of database principal cannot be impersonated, or you do not have permission. [dblink#8 @ 433]
TRACE-INFO: 21:                                                                                                           23 0.082797
tp returncode summary:
TOOLS: Highest return code of single steps was: 0
ERRORS: Highest tp internal error was: 0232
tp finished with return code: 232
meaning:
connect failed
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
ERROR: Connect to <SID> failed (20140222061008, probably wrong environment).
Process with ID 1756 terminated with status 232
<SID>Adm User has this environment variables:
dbms/type = mss
dbs/mss/server = <HOST>
dbs/mss/dbname = <SID>
dbs/mss/schema = <sid>
I check the following SAP Notes:
- 128126 - Database connect for external tools
- 525677 - Problems when starting shadow instance
- 592514 - MSSQL: internal database users, permissions and security
- 1294762 - SCHEMA4SAP.VBS
- 1727986 - Upgrade Phase MAIN_NEWBAS/STARTSAP_NBAS: Error Starting SAP
- 1910759 - Start of Shadow Instance Failed during upgrade
but any of them, help me to fix the stopper.
Can anybody give me any idea, please?

Hi Javier,
Have you tried by executing script mssupgsps.sql ,which you can find under D:\usr\sap\put\bin.This script will create stored procedure sap_upg_getrelease.
After execution provide grant with following
add setuser '<sid>'
grant all on sap_upg_getrelease to <sid>_shd
Hope this will help you.
Regards,
Gaurav

Cannot connect to GET STARTED page

Hello,
First off, I am sorry, I did a search and saw numerous posts on this issue, but about all of them either ended their replies after a user asked "Did you do this or that ?" or they just stopped posting... at most I saw some topics where it magically worked later on, but no real step-by-step instructions.
So, the problem: I installed XE 11g, no apparent problems during install (no warnings so I assume everything is OK), tried the GET STARTED link, but it said it can't connect.
System: Win XP PRO SP3, 2 gb ram using Firefox 7.0.1
DB: Oracle 11g Express Edition
Antivirus: avast 6 (firewall included), but disabled during testing...
lsnrctl:
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
STATUS of the LISTENER
Alias                     LISTENER
Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Produ
ction
Start Date                05-OCT-2011 02:36:42
Uptime                    0 days 0 hr. 21 min. 51 sec
Trace Level               off
Security                  ON: Local OS Authentication
SNMP                      OFF
Default Service           XE
Listener Parameter File   E:\Database\Oracle\app\oracle\product\11.2.0\server\network\admin\listener.ora
Listener Log File         E:\Database\Oracle\app\oracle\diag\tnslsnr\EASTFRONTIERS03\listener\alert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=EASTFRONTIERS03)(PORT=1521)))
Services Summary...
Service "CLRExtProc" has 1 instance(s).
Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "PLSExtProc" has 1 instance(s).
Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "xe" has 1 instance(s).
Instance "xe", status BLOCKED, has 1 handler(s) for this service...
The command completed successfullytns:
XE =
(DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = 127.0.0.1)(PORT = 1521))
    (CONNECT_DATA =
      (SERVER = DEDICATED)
      (SERVICE_NAME = XE)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
    (CONNECT_DATA =
      (SID = PLSExtProc)
      (PRESENTATION = RO)
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
    (CONNECT_DATA =
      (SID = CLRExtProc)
      (PRESENTATION = RO)
) listener:
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SID_NAME = PLSExtProc)
      (ORACLE_HOME = E:\Database\oracle\app\oracle\product\11.2.0\server)
      (PROGRAM = extproc)
    (SID_DESC =
      (SID_NAME = CLRExtProc)
      (ORACLE_HOME = E:\Database\oracle\app\oracle\product\11.2.0\server)
      (PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
      (ADDRESS = (PROTOCOL = TCP)(HOST = 127.0.0.1)(PORT = 1521))
DEFAULT_SERVICE_LISTENER = (XE)Services:
OracleJobSchedulerXE
OracleMTSRecoveryService
OracleServiceXE (started)
OracleXEClrAgent
OracleXETNSListener (started)sqlplus:
SQL> connect
Enter user-name: SYS
Enter password:
ERROR:
ORA-01089: immediate shutdown in progress - no operations are permitted
Process ID: 0
Session ID: 0 Serial number: 0alert_xe:
Wed Oct 05 02:37:35 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit record
Starting ORACLE instance (normal)
LICENSE_MAX_SESSION = 0
LICENSE_SESSIONS_WARNING = 0
Shared memory segment for instance monitoring created
Picked latch-free SCN scheme 2
Using LOG_ARCHIVE_DEST_1 parameter default value as USE_DB_RECOVERY_FILE_DEST
Autotune of undo retention is turned on.
IMODE=BR
ILAT =18
LICENSE_MAX_USERS = 0
SYS auditing is disabled
Starting up:
Oracle Database 11g Express Edition Release 11.2.0.2.0 - Production.
Using parameter settings in client-side pfile E:\DATABASE\ORACLE\APP\ORACLE\PRODUCT\11.2.0\SERVER\CONFIG\SCRIPTS\INIT.ORA on machine EASTFRONTIERS03
System parameters with non-default values:
sessions                 = 172
memory_target            = 760M
control_files            = "E:\DATABASE\ORACLE\APP\ORACLE\ORADATA\XE\CONTROL.DBF"
compatible               = "11.2.0.0.0"
db_recovery_file_dest    = "E:\Database\Oracle\app\oracle\fast_recovery_area"
db_recovery_file_dest_size= 10G
undo_management          = "AUTO"
undo_tablespace          = "UNDOTBS1"
remote_login_passwordfile= "EXCLUSIVE"
dispatchers              = "(PROTOCOL=TCP) (SERVICE=XEXDB)"
shared_servers           = 4
job_queue_processes      = 4
audit_file_dest          = "E:\DATABASE\ORACLE\APP\ORACLE\ADMIN\XE\ADUMP"
db_name                  = "XE"
open_cursors             = 300
diagnostic_dest          = "E:\DATABASE\ORACLE\APP\ORACLE"
Wed Oct 05 02:37:53 2011
PMON started with pid=2, OS id=2308
Wed Oct 05 02:37:53 2011
PSP0 started with pid=3, OS id=1168
Wed Oct 05 02:37:54 2011
VKTM started with pid=4, OS id=1920 at elevated priority
VKTM running at (10)millisec precision with DBRM quantum (100)ms
Wed Oct 05 02:37:54 2011
GEN0 started with pid=5, OS id=372
Wed Oct 05 02:37:54 2011
DIAG started with pid=6, OS id=1580
Wed Oct 05 02:37:54 2011
DBRM started with pid=7, OS id=1552
Wed Oct 05 02:37:54 2011
DIA0 started with pid=8, OS id=2668
Wed Oct 05 02:37:54 2011
MMAN started with pid=9, OS id=2132
Wed Oct 05 02:37:54 2011
DBW0 started with pid=10, OS id=3716
Wed Oct 05 02:37:54 2011
LGWR started with pid=11, OS id=3952
Wed Oct 05 02:37:54 2011
CKPT started with pid=12, OS id=2992
Wed Oct 05 02:37:54 2011
SMON started with pid=13, OS id=2616
Wed Oct 05 02:37:54 2011
RECO started with pid=14, OS id=1764
Wed Oct 05 02:37:54 2011
MMON started with pid=15, OS id=4012
Wed Oct 05 02:37:54 2011
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
starting up 4 shared server(s) ...
ORACLE_BASE from environment = E:\Database\Oracle\app\oracle
Wed Oct 05 02:37:55 2011
AUD: OS Error = 1717 encountered while writing audit record
Wed Oct 05 02:37:54 2011
MMNL started with pid=16, OS id=1516
Wed Oct 05 02:37:57 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit record
Shutting down instance (immediate)
Shutting down instance: further logons disabled
Stopping background process MMNL
Stopping background process MMON
License high water mark = 1
All dispatchers and shared servers shutdown
AUD: OS Error = 1717 encountered while writing audit record
Starting ORACLE instance (normal)
Wed Oct 05 02:38:02 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit record
Wed Oct 05 02:38:03 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit record
Wed Oct 05 02:38:03 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit record
Wed Oct 05 02:38:03 2011
AUD: OS Error = 1717 encountered while writing audit record
AUD: OS Error = 1717 encountered while writing audit recordFrom what I could gather from other posts here (and on other sites) the problem is I don't have anything listening on 8080. Other than that, all seems OK (I think).
So, can anyone tell me\help me on why that one isn't starting ? I reinstalled this 6 times and still can't figure out the problem... (as you saw, I even replaced the tns hostname with 127.0.0.1 out of paranoia). It's seriously driving me mad. Every topic I searched for (from the problem itself to even a step-by-step for dummies) shows an install, then the interface working... I see some questions regarding "I can't connect to..." but most are unanswered :(
Thanks in advance!
P.S. let me know if I forgot to mention anything relevant

TheNomad wrote:
orafad: Sad to say that was the full output...
C:\Documents and Settings\User>sqlplus / as SYSDBA
SQL*Plus: Release 11.2.0.2.0 Production on Thu Oct 6 12:55:47 2011
Copyright (c) 1982, 2010, Oracle. All rights reserved.
Connected to an idle instance.
SQL> select 1 from dual
2 /
select 1 from dual
ERROR at line 1:
ORA-01034: ORACLE not available
Process ID: 0
Session ID: 0 Serial number: 0
SQL>
jgarry: I believe what you explained may be related to the fact some reported the DB doesn't work properly when the event log is full (I just emptied mine so it doesn't apply). Normally I disable it but without it started, the DB is not working properly (not that I can get it started anyway).
There was a post on a site I found hinting at 3 things:
1. ORACLE_HOME must be defined as an env-var
2. ORACLE_SID must be defined as an env-var
3. there might be a problem with spfile
Regarding those:
1. shouldn't the setup declare it automatically ? I don't have it declared, but I added it (no change)As Orafad pointed out, Windows is different. It does have a search hierarchy it follows to figure out what the environment should be. So first, unset what you set and go into a cmd window and:
sqlplus sys as sysdba
Edit: Oops, I meant
sqlplus / as sysdba
startup
2. same as above, except I am not sure what SID to add so I didn't declare it ... The only 2 I have are PLSExtProc and CLRExtProc in tnsnames by default. I tried with each but the only thing that changes is instead of getting the shared memory realm error I get a TNS adapter error... trading one error for another is not funFor XE, the ORACLE_SID is XE (unless you do screwy things to change it). So now that I see you had some other db installed before, I suspect an environment collision. Delve into your registry and see what oracle definitions you have - this is a lot of work, things are spread around some, but searching for oracle is usually a good start. I'm not up on the 11.2 details (or others, really, I just have vague memories of seeing MOS notes that purported to explain clean up entirely, without truly doing so, and I avoid Windows as much as possible). I would uninstall XE, uninstall the other one, then search the registry for any leftover stuff, then install XE and see if it all magically works. But that is a fairly brain-dead way to deal with it.
So that said, you can set up a little batch file to set your environment in a cmd window (specifically ORACLE_HOME and ORACLE_SID), and go into sqlplus / as sysdba and give the startup command. If you get the memory realm error, you have one of those wrong, if you get the tnsnames errors you can fix those following the advice in Ed Steven's blog. You can run tnsping to see which tnsnames.ora you are using, if you use one (which is determined by an @ sign in your connection string, which you should not need to connect locally, but if you do, you need to have XE defined in the tnsnames.ora, and may need to set TNS_ADMIN to get the right one).
Your tnsnames.ora should have an entry like this:
XE =
(DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = Yourcomputer.yourdomian.whatever)(PORT = 1521))
    (CONNECT_DATA =
      (SERVER = DEDICATED)
      (SERVICE_NAME = XE)
)You might want to search for any tnsname.ora on your computer, the default correct one would be: C:\oraclexe\app\oracle\product\11.2.0\server\network\ADMIN\tnsnames.ora
3. I don't have that file in the folder but I suspect it might be created on a first successful launch of the DBWithout an spfile you need to use a pfile, then create a pfile from spfile. But there should be one at C:\oraclexe\app\oracle\product\11.2.0\server\dbs\SPFILEXE.ORA (if you used default installation).
>
Other than that I didn't find anything helpful in logs (or don't know where else to look), nor on sites.
I did have WAMP installed at a point (uninstalled it) but if it were to conflict I guess SETUP would tell me (since the XE license doesn't let you use 2 DBs at the same time)Is that some mysql thing? That shouldn't interfere. It's only installing multiple Oracle products related some what to the Oracle database that can be a problem, and normally isn't with the more recent stuff.
I swear to god this is killing my neurons :(When you find the solution, you will slap your forehead.
Edited by: jgarry on Oct 6, 2011 9:36 AM

RSA1 - Source system connection : No connection to system possible

Hello friends,
I am creating a Source system connection from our BW system. I have already established the working RFC connection to source system which works fine, both side client is open & system is modifiable.
Bit i am getting error : No connection to system possible
No connection to system possible
Message no. RSAR501
Diagnosis
Logical system cannot be accessed.
System Response
Error during the retrieval of the logon data store d in secure storage
Procedure
Use transaction SM59 (for BAPI and SAP source systems) or DBCO (for database source systems) to check the RFC parameters of source system . Also check whether the system can be accessed in the network and whether the necessary application and system programs have been started.
I have already implemented SAP note 1276270 - RSAR 501 for source system restore due to router string /H/ without success.
thanks
ashish

Error during the retrieval of the logon data store d in secure storage
Have you tested the remote login also ?
Regards,
Subhash

URGENT: connection to system landscape Directory (SLD) could not be openend

Hi ,
information: when login as adminstrator yesterday, it asked for a new password & i given a new password to the administrator
Error in portal: Failed to resolve JCO destination name 'WD_GPMS_RFC_METADATA_DEST' in the SLD
My Findings
1) http://...../sld , given j2ee_admin, pwd .
then clicked on Administration --> showing --> status running.
2) Logged into portal with j2ee admin , CA --> web dynpro ,
Create Jco Destination , Maintain JCo destinatations , start assigned SLD are in the disabled mode.
Check SLD Connection is in enable mode.When clicked on test connection ,
it is giving the following message :
connection to system landscape Directory (SLD) could not be openend successfully.
3) Also CIMClient test giving failed .
With Regards,
NSM

Hi Nikil,
i had seen your reply after i had resolve the issue by my own. As my administrator password got changed, i had changed SLDDSUSER password. Both adminstrator password & SLDUSUSER password should be same.
(any how iam rewarding you with points as mostly it is correct answer)
Thanks
Hussain.

Auto Start IChat program at System Start?

Is there a way to automatically start IChat when the system starts? IE: Auto Login so I don't have to "Manually" start it each time?

NOTE for some.
It is worth noting that on some (Slower) Macs that, as the Start Up procedure actually connects to the Network quite late in the order of things, you may have problems.
The Mac will in fact start to launch apps listed in the Login Items before the whole Start Up procedure has finished.
This can mean if iChat is the only item or high on the list in Login Items that it can not find the Network and Log In before Start Up has finished.
You may have to delete iChat from it's position in the list as it is not drag-able and re-enter it to have it later in the order of things.
4:32 PM Sunday; March 29, 2009

No connection to system possible

Hi,
We upgraded from 4.6c to ECC6 and we had separate BW 3.0b. but we didn't upgrade BW to ECC6.
So now my task is to re-do all infoobjects, cubes etc in ECC6.
Now i'm trying to figure out, any easy method to do it via RFC connection between BW 3.0 and ECC6 BI, can copy all the objects back to BI.
So when i go to BI source system creation for BW 3.0 getting the following error:
==========================
No connection to system possible
Message no. RSAR501
Diagnosis
Logical system cannot be accessed.
System Response
RFC destination %%ashost=172.16.33.31,sysnr=,clien t=000,logon_screen=X does not
Procedure
Use transaction SM59 (for BAPI and SAP source systems) or DBCO (for database source systems) to check the RFC parameters of source system . Also check whether the system can be accessed in the network and whether the necessary application and system programs have been started.
===========================
In SM59 i can able to remote logon to BW 3.0 from ECC6 and also vice versa.
So i'm just thinking, whether i'm going on the correct path or this cannot be done at all.
Thanks.

Hey Ani,
I found the following on SDN:
RSAR 154 error while trying to connect an R3 system in BW
Since your on 3.0 maybe Note 581273 applies to you.
Anyways do check the access with sm59 on BOTH system.
Hope this helps,
Andreas

CacheRefreshException: Connection to system RUNTIME using application...

Hi experts,
I have a following problem: SXI_CACHE is not functioning with following message.
com.sap.aii.ib.server.abapcache.CacheRefreshException: Connection to system RUNTIME using application RUNTIME lost. Detailed information: Error accessing "http:<xihost>:80xx/run/hmi_service_id_fresh_swcv/int?container=any" with user "XIDIRUSER". Response code is 404, response message is "Not Found".
I have checked users, passwords and roles - everything looks ok. RFC connections too. It is about Netweaver 2004s (SP09) Java stack restart. I tried many Sap notes, but have not found nothing eficient.
It seems to me, that port shall be in range 5xx00 not 80xx. Manually, I have tried 5xx00 port in broser and it works.
Integration Engine (ICM) port was in range 5xx00 which I have changed to 80xx (in TC SMICM, Exchange profiles and SLD) according to recomendations. All this started to happen after J2EE Stack restart.
Why is it pooling wrong port ?
Regards
Jurica

FYI
In mean time we found the problem:
On of exchange Profile parameters (com.sap.aii.connect.integrationserver.httpport) was set to wrong port - to 80xx instead of 5xx00. After Java Stack restart from SMICM, everything was ok again.
So, this is actually Java Stack port parameter, com.sap.aii.connect.integrationserver.r3.httpport is ABAP Stack port.
Regards
jurica

Default Connections (SYS, SYSTEM, DBSNMP, SYSMAN) Unavailable When SQLOpens

I installed the 32-Bit version of Oracle 11gR2 on my Windows 7 x64 system because the x64 version wouldn't install. I downloaded the 32-Bit version of SQL Developer with JRE, but when I run SQL Developer, the default connections (SYS, SYSTEM, DBSNMP, and SYSMAN) are not available.
I have entered the tnsnames directory on the Database:Advanced Preferences screen, and restarted my PC, but there's obviously something I'm missing.
Suggestions?
Thanks.

Hi Paul,
Once I connect to the Network Adapter, will the default ids show up?The SQL Developer Help says (and I believe this procedure works even if you cannot "connect" to the local database):
To create (automatically generate) a database connection for each unlocked user account in the Oracle database instance
on the local system, right-click the Connections node and select Create Local Connections. The connections are placed in
a folder named Auto-Generated Local Connections. Note that for these autogenerated connections (except for the one
named system-<database-name>), you will always be prompted for the password when you connect, and you cannot edit
the user name or password in the connection properties dialog box.Next, if this what you are actually asking, and you have a local database installed, then you need to make sure your database listener is up and running. Open a command line and try these commands:
lsnrctl statusIf it is not already started, either start it with
lsnrctl startor otherwise from your Windows Administrator Tools -> Services -> Oracle<home>Listener (right-click: Start)
Hope this helps,
Gary

DEBUG CONNECT SESSION system privilege

Hi everyone. It's my first post to this forum so I'd like to say hello :)
I'm completely new to PL/SQL language. I'm using PL/SQL Developer and I want to make a simple testscript but when I launch it communicate appears
Debugging requires the DEBUG CONNECT SESSION system privilege
could You tell me how to set that? Greetings. P.

in the xp:
start>run>cmd
in the cmd console:
1. set oracle_sid=<bobens_83-here_goes_your_db-name>
2. sqlplus /nolog
3. conn sys as sysdba
4. sqlplus may asks for password - if it does, bobens_83, supply the password that was chossen during the install process.
5. grant DEBUG CONNECT SESSION to =<bobens_83-here_goes_your_db-username>
6. exit sqlplus
7. exit cmd
in the xp:
try to debug using PL/SQL Developer.
Have fun,
Amiel Davis

Dúvida - NF-e: Maintain Connected Authority Systems - layout 3.10

Boa noite!
Estou realizando o customize da SPRO, porém notei que só posso inserir a seguinte entrada para um mesmo CNPJ:
Ou seja, quando tento colocar os demais estados o erro de chave duplicada é retornado devido aos campos logical system e Company's Own CNPJ. Dessa maneira, quando executo o novo programa de status de serviço (/XNFE/NFE_CHECK_SRV_STATUS) relalizando o debug noto que existe uma verificação durante a execução da função (/XNFE/SRVSTA_READ_CUST) na qual, por mais que eu tenha cadastro todos os cUF na spro que ficam registrados na tabela (/xnfe/tcuf) o status de serviço acaba sendo executado apenas para o que existe na tabela (/xnfe/govpar) alimentada pela configuração da NF-e: Maintain Connected Authority Systems da imagem que enviei posteriormente. Sendo assim só é executado o status de serviço para SP e não para todas as cUF que estão na atividade NF-e: Define Service Status Request for Authority (SEFAZ). Abaixo segue trecho do código que verifiquei que realiza esse controle no debug:
SELECT * FROM /xnfe/govpar INTO TABLE lt_govpar
                              WHERE doctype = iv_doctype.
*--- 2. Version determination
IF lt_govpar IS NOT INITIAL.
    SELECT * FROM /xnfe/xmlversdet INTO TABLE lt_xmlversdet
                       FOR ALL ENTRIES IN lt_govpar
                             WHERE doctype = iv_doctype
                               AND logsys   = lt_govpar-logsys
                               AND ( cnpj     = lt_govpar-cnpj
                                OR   cnpj     = ' ' )
                               AND messtype = iv_messtype.
*--- 3. Service status check parameter
    SELECT * FROM /xnfe/tcuf INTO TABLE lt_tcuf.
    LOOP AT lt_govpar ASSIGNING <ls_govpar>.
*--- Get corresponding entry from version determination
      READ TABLE lt_xmlversdet WITH KEY doctype = <ls_govpar>-doctype
                                        logsys = <ls_govpar>-logsys
                                        cnpj    = <ls_govpar>-cnpj
                              ASSIGNING <ls_xmlversdet>.
      IF sy-subrc <> 0.
*--- If nothing is found try with blank CNPJ
        READ TABLE lt_xmlversdet WITH KEY doctype = <ls_govpar>-doctype
                                          logsys = <ls_govpar>-logsys
                                          cnpj    = ' '
                                ASSIGNING <ls_xmlversdet>.
      ENDIF.
      IF sy-subrc IS INITIAL.
*--- Get corresponding entry for service status check parameter
        READ TABLE lt_tcuf WITH KEY doctype = <ls_govpar>-doctype
                                    cuf     = <ls_govpar>-cuf
                                  ASSIGNING <ls_tcuf>.
        IF sy-subrc IS INITIAL.
          ls_stacheck-cuf       = <ls_govpar>-cuf.
          ls_stacheck-tpamb     = <ls_govpar>-tpamb.
          ls_stacheck-xmlvers   = <ls_xmlversdet>-xmlvers.
          ls_stacheck-sscperiod = <ls_tcuf>-sscperiod.
          ls_stacheck-tzone     = <ls_tcuf>-tzone.
          ls_stacheck-respcont = <ls_tcuf>-respcont.
          ls_stacheck-checkcont = <ls_tcuf>-checkcont.
          APPEND ls_stacheck TO et_stacheck.
        ENDIF.
      ENDIF.
      CLEAR: ls_stacheck.
    ENDLOOP.
ENDIF.
Sendo assim, como faço para que na atividade NF-e: Maintain Connected Authority Systems eu possa inserir todos os cUF com para os quais executarei o status de serviço e posteriormente enviarei notas?
Obrigado.,

Bom dia Luís,
Exatamente! De fato o que ocorreu foi uma confusão, pois na versão anterior era possível enviar o status de serviço mesmo se você não possuísse uma filial para o estado em questão. Quando fui fazer a migração do cliente todos os estados estavam configurados para emitir status de serviço, porém não há necessidade de enviar o status de serviço para um estado visto que você não possui uma filial para emissão de Nota no mesmo.
Abs.,

NF-e: Maintain Connected Authority Systems - Já existe uma entrada com a mesma chave

Bom dia!
Estou tendo um problema para adicionar novas entradas na SPRO - OUTBOUND -NF-e: Maintain Connected Authority Systems para configuração do layout 3.10:
Sendo assim, como devo configurar todos os estados para a SEFAZ se o sistema lógico e CNPJ são chaves da tabela /xnfe/govpar?
Com isso, não consigo executar todos os status de serviço no layout novo através do report (/XNFE/NFE_CHECK_SRV_STATUS) depois de cadastrálos na atividade NF-e: Define Service Status Request for Authority (SEFAZ,) pois durante a execução do report (/XNFE/NFE_CHECK_SRV_STATUS) além da tabela /xnfe/tcuf a tabela /xnfe/govpar também é verificada.
Grato.,

Bom dia Luís,
Exatamente! De fato o que ocorreu foi uma confusão, pois na versão anterior era possível enviar o status de serviço mesmo se você não possuísse uma filial para o estado em questão. Quando fui fazer a migração do cliente todos os estados estavam configurados para emitir status de serviço, porém não há necessidade de enviar o status de serviço para um estado visto que você não possui uma filial para emissão de Nota no mesmo.
Abs.,

Upgrade phase STARTSAP_NBAS error: SYSTEM START failed

During an upgrade from BW 3.5 to BI 7.0, I get the following error
message in phase STARTSAP_NBAS:
SYSTEM START failed, code -2
-2: the test rfc did not work.
Try to log on to the system with user DDIC
When I try to log on to the system as user DDIC, I get the following
error message:
DB-Error -0
The same thing happens when I try to log on as SAP*. I am certain that
the password I submit is correct. I have not changed this password at
any time.
I have included SAP_BASIS support package 14 into this upgrade, and
this requires kernel version 133 at least (Note 822379). This kernel
was copied into the usr\sap\put\exenew directory before the upgrade
began. However, the system still seems to run on kernel version 111.
I have tried to put the 133 kernel into
F:\usr\sap\BWS\SYS\exe\nuc\NTAMD64 so that it is copied into
F:\usr\sap\BWS\SYS\exe\run during system startup, but then all my work
processes die. The gateway also seems to be down using this kernel.
Please help!
Regards,
Thomas

Hi.
I made a stupid mistake.. the kernel I was using was unicode, but I should use a non-unicode kernel..
Regards,
Thomas

Connection at system start

Similar Messages

Maybe you are looking for