Convert KI DAQ libraries from LabView 5.0 to 2009
Hello everybody!
I have in the following zip containing the 4 libraries that can control my PCI 3102 acquisition card from Keithley.
Unfortunately, these libraries were implemented in LabView 5.0 and I have the new 2009.
I saw on other posts that the easiest solution is to ask if someone has intermediate version of LabView (like 8.0 or 8.2, preferably 8.2.1 according to the FAQ http://zone.ni.com/devzone/cda/tut/p/id/8387). In these versions, the libraries will be opened without any problem, and you could just save them in the earlier release so that I can open them in 2009.
It could be very nice if one of you could do it so that I can avoid installing LabView temporary version just to convert these 4 libraries!
Thanks in advance for the help.
Attachments:
KI DAQ Examples.zip 1428 KB
Well, the easiest thing to do would probably be to get up to date code from Keithley.
Here they are but you did not include the low level functions so you would need to convert those or get them from Keithley.
Attachments:
KICT Examples_71.zip 970 KB
Similar Messages
-
How to read the gain list of a DAQ card from labview?
Hi,
Its known that you can set the gain of an ADC of a DAQ card by setting the high and low values.
Different cards have got different signal ranges corresponding to different gains.
My question is ... Is it possible to read the gain list of a DAQ card from labview?
It is definitely possible to read the signal ranges available for the device. It would be very helpful if some one can tell me the method to read the gains corresponding to the signal ranges.
(Even the device specification provides only the signal range but not the gain corrsponding to it )
Thanks
Message Edited by Vsh on 04-08-2008 03:50 AMHi Vsh,
It appears that you have found the gains applied for the various ranges (I assume from the user manuals). So if I understand your question correctly, you are looking to poll the card for the current gain (or the various gains available)
Because DAQmx selects this for you (unlike Traditional DAQ), there is not a way to poll directly. If you want, you could poll the min/max values and then use this to figure out the range setting (and thus the gain).
Please refer to this post, it gives more information about the gains/ranges in general.
I would suggest putting in a product suggestion if you would like this feature. Those go into the decision making process for our R&D team, meaning they actually do look at them. If you wish, I can submit a suggestion internally was well for you, that way your suggestion gets 2x the exposure. Let me know if you want me to do this.
Neal M.Applications Engineering National Instruments www.ni.com/support -
Uograding from labview 8.5 to 2009
I'm thinking about upgrading from LabVIEW 8.5 to 2009. We currently call a large number of VIs from TestStand 4.01 - What risks do you see in making this move (i.e. drivers, breaking code)
The same risks one would see in updating, from, say 7 to 8, or 6.1 to 8.5. If you're using Toolkits then you should first check to make sure there are 2009-compatible versions of toolkits. As far as drivers are concerned, it's the same thing. What drivers are you using? If it's DAQ, then just make sure you get the latest DAQ software.
Some things will be different, but nobody can predict what problems you're going to have because we don't know what your code is doing. Your best bet is to look over the Release Notes for 2009 and see if you are using anything that has been drastically changed in 2009. -
I want to take the .DAQ file from the MAX program and convert it to a text file. From my understanding this file contains all the information for the channels and hardware that is currently set up on the system. I want to use this data as a file so that others can set up the experiment again in the future and this data would be helpful. Thanks in advance for any help in regard to this matter.
HAL;
I'm attaching a Labview example to this answer which does that with the properties of your virtual channels configuration in MAX. Other than that, there isn't any way, at this time, to convert the .daq file to a text file.
Hope this helps.
Filipe
Attachments:
vrtchstf.zip 19 KB -
Down convert from LabView 9.0 to 8.6
I would greatly appreciate it if someone could convert the attached file from LabView 9.0 to 8.6.
Thank you.
Solved!
Go to Solution.
Attachments:
Read_Value_From_Excel_LM6.vi 26 KBOnce again, saved in 8.0
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Read_Value_From_Excel_LM6_nijams.vi 36 KB -
Please Convert Vis from Labview 2013 to Labview 2011
Please convert the attached Vis from Labview 2013 to Labview 2011
Solved!
Go to Solution.
Attachments:
Convert from2013 to 2011.zip 255 KBHere you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Attachments:
Converted to 2011.zip 176 KB -
Can't launch DAQ assistant in LabVIEW
Hi
I cannot launch DAQ assistant from LabVIEW, but i can do that from MAX. DAQ from MAX is not that flexible because i can't customized the code or convert it. I 've tried all the various ways to open DAQ assistant and i finally realized something, on the block diagram, i open Tools/Advance/Edit palette/Express/Input/DAQ is missing (question mark) and many more functions are missing.
I'm using the evaluation software of Labview 8.6 and NIDAQmx 8.7.1
Can you please tell me what is wrong. I really need to launch NI DAQmx from LabVIEW.
Rgds
Paul
Solved!
Go to Solution.Hi Christ
Thanks for the feedback.
From Block diagram interface: Function palette/Measurement
I/O ? (there is nothing just MAX config).
But from Front Panel: Modern/ I/O controls, i can see DAQmx names controls
which i don't think i need now.
What do mean reintalling DAQmx with LV
support, is it different from the LabVIEW evaluation software or i just have to
reinstall the LV
evaluation software.
Rgds
Paul -
Conversion from LabVIEW 2011 to 8.2
Dear All
Can any body help me to convert the attached file from LabVIEW 2011 to LabVIEW 8.2.
Kind Regards
Muhammad Irfan
Solved!
Go to Solution.
Attachments:
LabVIEW 6281-40 Replace.vi 76 KBThis is what the Version Conversion board is for. But here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
LabVIEW 6281-40 Replace.vi 99 KB -
Conversion from LabVIEW 2012 to 8.2
Dear All
Can any body help me to convert the attached file from LabVIEW 2012 to LabVIEW 8.2. Please send the file in doc or pdf as well.
Kind Regards
Muhammad Irfan
Solved!
Go to Solution.
Attachments:
PVT - Mathscript Node.vi 83 KBHere you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
PVT - Mathscript Node.vi 90 KB -
Convert Keithley 6485 Driver and Examples Libraries from LV5 to LV8.6
Can someone please convert the attached Keithley 6485 Driver Library and Examples Library from LabView v5 up to LabView v8.6 - these are the current libraries that Keithley have on their website.
Photon999
Attachments:
KE6485.LLB 2952 KB
KE6485 Examples.llb 795 KBForum member smercurio_fc converted these files for another member to 8.2 which you should be able to open in 8.6. Below is the link.
http://forums.ni.com/t5/Version-Conversion/Upconvert-Keithley-6485-to-10-from-5-1/m-p/2108260#M1151
Hope this helps. -
Convert from Labview 5.1 to labview8.6
Hello Everyone,
Can any one please convert this vi from labview 5.1 to labview 8.6 or labview 2009
Thanks in advance
Nadim
[email protected]
Attachments:
4-Channel Power Spectrum with estimate.vi 750 KBHi,
Here it is in LV 8 but there are some VI's missing (DAQ)
Kees
Attachments:
4-Channel Power Spectrum with estimate.vi 402 KB -
Need to convert to labview 11 from labview 12
hello
I need to convert the following Labview 12 VIs to Labview 11.
thank you in advance
Attachments:
QAM Demodulation.vi 30 KB
QAM Modulation.vi 30 KB
rx QAM.vi 57 KBThe conversion was done here: http://forums.ni.com/t5/Version-Conversion/need-to-convert-from-Labview-12-VI-to-Labview-11/m-p/3021...
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines -
Error message from labview when trying to set up the DAQ assistant
I recieve a message from labview when I try to set up the DAQ assistant and select a channel to use. The error I get states "An exception occured within the external code called by a Call Library Node. This might have corrupted LabView's memory. Save any work to a new location and restart labview". Labview then freezes. I have reset the DAQ device in trying to slove this but I still get the same message. How do I solve this?? thanks - mars2006
Hi Mars-
It sounds like your NI-DAQ installation may have become corrupted. I would suggest uninstalling and reinstalling the DAQmx 7.4 driver to correct this problem and ensure that you're up to date. This download is available here: NI-DAQ 7.4
If the problem persists you may want to uninstall and reinstall LabVIEW and then NI-DAQ in that order. The error message will usually give an indication as to which VI the error occurred in. Please let us know which VI is failing if you're unable to avoid the error with these suggestions.
Have a good day-
Tom W
National Instruments -
Convert from LabVIEW 2011 to LabVIEW 9.0
Please convert from LabVIEW 2011 to LabVIEW 9.0
Attachments:
Watlow Vis.zip 76 KBLooks like somebody forgot to attach the zip file. Here you go.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Watflow.zip 57 KB -
Converting from LabView 4.0 to 9.0
I also need to convert this llb from LabVIEW 4.0; to 9.0. Anyone willing to do this for me? see attached and thanks...
Attachments:
gj18i.llb 247 KBHey!! Could somebody help me?? I have an labview 2009 and it would be nice if somebody could convert these files (version 4.0.1) for me! Thx
Attachments:
lgy1m.llb 73 KB
Maybe you are looking for
-
ITunes won't open from dock or apps
When I click on the iTunes icon on the dock, it bounces once (sometimes twice), then stops bouncing and nothing opens. I tried opening from the application folder and nothing. I tried downloading the most recent version, but then I can't open the .dm
-
How to creat a global variable?
I want to creat a start button of global variable to control different programs in the sequence structure. But I do not know how to creat it. Thanks for answering. Solved! Go to Solution.
-
Create condition table V/57
Hi all, I'm trying to create a new condition table for output determination and need it to be based on the Sales office, and the customer account group KTOKD. However, the field KTOKD is not available as an allowed field when creating the condition t
-
Problem with fixing pagerdeluxe and progressbar while using jsf-ibm.jar
hi, I am having a jsf data table with <hx:pagerdeluxe> to navigate, and i am using (jsf-ibm-unknown-vers.jar) jar, this works fine. I need to insert a progress bar in my jsf and used <hx:progressBar> but this was not available in the old jar, So i up
-
How can I play youtube on OSX 10.5.8?
If I upgrade to Snow Leopard 10.6 will I be able to get an Adobe Flash Player current enough to play youtube videos?