CRC Errors and Sound Problems

Everytime I try to install something from my CD drive I get CRC errors. I sometimes get sound distorsions when I'm playing but those are not permanent and the original sounds come back after a couple of minutes. Can you help me fix this.
Intel P4 2.6
MSI 865PE Neo2
Radeon 9800 Pro
OCZ EL DDR PC-3200 / 400MHZ / Platinum / Dual Channel (2x512)
Maxtor SATA 80 Gig
CD Rom Creative 52X
LG DVD / CD Writer Combo 16X / 52X

Quote
Originally posted by Starscream
I'm using Slow performance and I just bought my computer. The problems started the first time I tryed to install XP Pro and never stopped after that.
No offence.....
Gen copy of XP Pro???????
This does not sound like a MainBoard issue............???? But will help all I can.
Del

Similar Messages

CRC Error and input Error how can fix these

FastEthernet0/13 is up, line protocol is up
Hardware is Fast Ethernet, address is 0004.4d27.66cd (bia 0004.4d27.66cd)
Description: EDL-P-Box-NO-4
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 250/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex (Full), Auto Speed (100), 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 18:52:43, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 12000 bits/sec, 6 packets/sec
5 minute output rate 24000 bits/sec, 6 packets/sec
     14488019 packets input, 2783320210 bytes
     Received 345346 broadcasts, 0 runts, 0 giants, 0 throttles
     261028 input errors, 259429 CRC, 1599 frame, 0 overrun, 0 ignored
     0 watchdog, 84207 multicast
     0 input packets with dribble condition detected
     19658279 packets output, 3529106068 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
PAD-8-1-10.179#cle
v

Hi,
Check out the below explanation for CRC error and farme error and few useful links to trouble shoot these type of problems
The CRC error rate is 1.75915% (greater than 1 in a million packets),
and the collision rate is less than 0.1%.
This can indicate excessive noise or transmission problems on the LAN or the LAN
bus itself. A high number of CRCs is usually the result of collisions or a station
transmitting bad data.
TRY THIS: Check cables to determine whether any are damaged. If 100BaseTX is being
used, ensure Category 5 cabling is being used and not another type, such as Category
3.
There have been 1599 'frame errors' reported.
This indicates the number of packets received incorrectly, having a CRC error
and a non-integer number of octets. On a LAN, this is usually the result of collisions
or a malfunctioning Ethernet device.
TRY THIS: Monitor the level of frame errors over time. If they are increasing,
try swapping interfaces and or ports to identify the problem.
http://www.cisco.com/en/US/customer/products/hw/modules/ps2033/products_tech_note09186a008009446d.shtml
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1904.html
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1904.html
Hope that helps out your query !!
Regards
Ganesh.H

CRC error and collisions

We discover a incrasing problem ved CRC errors and Collisions on catalyst 2950 and catalyst 3560 connected to clients (PC?s)with Gigabit NIC. Gigabit NIC?s is common on all new PC?s. The NIC?S are forced to 100 Mb half duplex and newest drivers.
The configuration on switchport is as follow: 100 Mb half duplex
Anybody know why ?

The matched duplex will elimiate the collision problem. But for the CRC, there may be another issue.
According to below link, CRC errors occur when a number of frames arrive with an invalid CRC.
CRCs on the Ethernet are usually an indication of cabling problems. Verify whether all network cable connections are clean, and ensure there is nothing that can cause electromagnetic interference on the cabling.
http://www.cisco.com/en/US/products/hw/wireless/ps441/products_tech_note09186a0080177aa0.shtml
Hope this helps.

CRC errors and input errors on Te 1/2 of Cisco WS-C3560X-48 switch

Hi All,
I am observing CRC errors and input errors on one of the Te1/2 interface of WS-C3560X-48 Cisco switch. I have not observed any CRC errors or input errors on the connected interface at other end. Can you please let us know whether the issue is with cable or SFP module.
Effected interface:
TenGigabitEthernet1/2 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is f866.f243.e6b6 (bia f866.f243.e6b6)
Description: *** MAN-SW1B***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 254/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 29000 bits/sec, 30 packets/sec
5 minute output rate 45000 bits/sec, 37 packets/sec
68905128 packets input, 8272036576 bytes, 0 no buffer
Received 68904979 broadcasts (68812046 multicasts)
0 runts, 0 giants, 0 throttles
146170 input errors, 130065 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 68812046 multicast, 0 pause input
0 input packets with dribble condition detected
83524620 packets output, 12642123488 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Other end.
TenGigabitEthernet1/4 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet Port, address is 503d.e53b.9703 (bia 503d.e53 b.9703)
Description: *** DMZ-SW1B ***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s, link type is auto, media type is 10GBase-SR
input flow-control is on, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 32000 bits/sec, 27 packets/sec
5 minute output rate 21000 bits/sec, 22 packets/sec
918379921 packets input, 312586470396 bytes, 0 no buffer
Received 881142868 broadcasts (875016400 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
463132111 packets output, 240865283601 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

When there are more than two members in a cluster (stack), the Gigabit interface operates at half-duplex. Since collisions can result at half-duplex, some CRCs errors are normal.

Ipod 5 keeps getting CRC Error and temperature message

my ipod touch Gen 5 keeps getting the message that The temperature is too high and needs to cool down. So I shut it down. This message is constantly popping up whether I am 30 seconds into a song or I open my mail. But once I turn it off it turns itself back on. It will not stay turned off. my ipod has also been crashing on a daily basis too. When I look at the diagnostics the common factor is CRC Error. I have ios 8.1.2. I would also like to add that the Bluetooth function barely works and the time is never correct I try and fix multiple times a day but it usually crashes or "overheats" before I can. Please help! I haven't gotten it wet or left in the sun, these problems started after the last update. im ready to snap it in half and be done with Apple products forever.
-chels

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. The message likely means a hardware problem
Apple Retail Store - Genius Bar

Curve 8330 Voice dialing and sound problems, Please help!

I got this black berry curve 8330 from a friend on the weekend to replace my broken Pearl. He said it worked fine but it sometimes had a voice dialing problem. After wiping all the personal data and activating the phone the voice dialing went nuts. Every 6 to 9 sec the voice dialing would activate with no sound. meaning you don't hear the lady voice say, "say a command". After reading many forums posts I download memmax and removed all VAD files. But I will still left with no sound. I went and did a test on the hardware and the speaker and microphone both worked fine. Puzzled I tried playing a ringtone, , it plays maybe the first second of the file and then the sounds goes away but I am able to get it back by press the Speaker/$ key. I then tried making a phone call and the phone was working just fine. About an hour later I tired calling someone and the issue had raisin again. This time I was unable to get the sound back. (I tried resetting many times with no success.) I could still play media files, but was unable to get sound making or receiving calls (this includes the other party not being able to hear me as well.) I tired changing profiles with no success. I then did some more reading and tried updating the OS. Once that was done and voice dialing had been reinstalled and started acting up again. SO I removed it and basically everything happened all over again. So right now I have a phone that I can’t make calls on but I can still text and use the internet. Does anyone know a solution to this problem? Should I try wiping the OS and reinstall or is this phone toast?

The msi nforce package 2.29 fixes the NVMCP.SYS error and turns it into a very rare system freeze. 8o
Very rare!
been waiting almost 9 months for this fix so i could pull the damm soundblaster out! :O

Router CRC error and IP conflict

Hi All,
I just setup my Cisco router 1921/K9 router via lease line. I managed to reach both end using ping command via local network. After an hour, my local LAN with different subnet starting to act weird, IP conflict error message pop up on the screen. It gradually spread over the network, PC by PC.
By issuing #sh int s0/0/0 and #sh int giga0/0 , I can see an input error, and CRC error. "Reliability" was perfect 255/255. Duplex and Speed all set to 100Mbps full duplex.
I have been looking into this matter for a few days, but still no idea what is actually going on. When I unplug LAN cable from giga interface to my local LAN cisco switch, IP conflict has disappeared.
Has anyone encounter this issue before? Kindly assist.

Hi,
As per my understanding you are facing 2 different issues one is related to IP conflict and other is CRC and i don't think both have any co-relation as such.
- Are you using DHCP to assign IP address to the users or static? Check if anyone is using the same IP addresses causing this problem.
- For CRC error check with your provider. To isolate any hardware related problem you can try loop test.
If you feel your query has been answered please mark this as answered. In case you have any additional query please feel free to contact.
Thanks & Regards
Sandeep

Satellite L750D - BIOS update 2.1 and sound problem

Hello
I have little problem. I have been downloaded from your website BIOS 2.1 for Toshiba Satellite L750D (PSK32E).
I have been updated BIOS to 2.1 and start problem with sound. When I start game, music or something other only 2 first minutes sound plays properly but then it stops for no reason. No sound at all. I have been reinstalled op system but the problem is still there.
Sound works for 2 minutes only then is completely off. Every start application with sound plays 2 minutes and stop all quiet is. I have made a probe on my mother laptop its a twin laptop. I have been updated bios same problem 2 minutes and then no sound. My operating system is win 8 pro 64 my mother laptop is with win 7 x64 premium.
Two BIOS updated 2.1 ver on L750D and the problem is same. Please fix BIOS.

The BIOS seems to be very old. I was released nearly 1.5 years ago so to be honest I doubt its and BIOS issue.
I had the similar issue with my other notebook equipped with an Realtek sound card.
The sound appeared again after plugging and removing the headphone jack
But i could solve this installing the newest sound driver update from Realtek driver page.
But it seems that your Satellite does not support Realtek sound chip but Conexant sound chip.
Therefore the solution might not be useful for you.
However, I think you need to update the sound driver.I recommend you to google for Conexant SmartAudio HD driver and to test the newest available driver version.
In internet I could found the Conexant SmartAudio HD Driver version 8.65.9.51 for Win 7/ Win 8 / Win 8.1
Not quite sure if this is the newest version but you can test it.
In order to manually update your driver:
1. Go to Device Manager (right click on My Computer, choose Manage and then find Device Manager in the left panel)
2. Right click on the hardware device you wish to update and choose Update Driver Software
3. Choose to select the location of the new driver manually and browse to the folder where you downloaded the driver

Regarding Workflow Error and Notification problem

Hi,
I am working on Workflow. I imported data first time in Data Manager and created new workflow. Now while "Launching" this workflow it is showing error "The record is currently used in workflow".
I was using this repository for other data with different workflow but i deleted all previous data and workflow. Why it is showing this error? When i have new set of data with new workflow than i think i should not show this error.
Other Question is regarding Notification:
To notify the person we have to make following changes :
1) Have to use Notify stencil and have to give e mail ids in User detail
2) In my server ini file i have to give my mail server name.
After making this changes I am not getting any mails. Please guide me for the same.
Please guide me how to rectify this error and what are the prerequisites?
Thanks in advance,
Ronak

Hi Ronak,
Couple of issues with emailing:
1. You need to restart your repository after updating .ini file to effect the changes.
2. Your SMTP server should relay mails without SMTP authentication.
3. You can also send emails to outside domains such as yahoo or others if your SMTP server permits.
Check with your mail server administrator and perform a simple SMTP telnet test to make sure your SMTP server is not an issue.
Hope this helps
Venkat

IMovie 11 export unsync, transition problem, and sound problem

Hi all. I have done a 1 hour and 36 min long movie on my weeding and it's made of around 80 "clips", where in some places the original sound is used and in some places external sound is placed instead. In some places iMovie text boxes is used and in some places the video has filters and slow motion (so a lot of random filters, effects, etc and chapters).
So my problem? 3 weeks ago I wanted to just test the video before doing everything done and exported it as mov HD1080 and it worked good on other devices. When improvements done I tried to export it again. But as it is now, when I export is, regardless if its to iDVD, iTunes, MOV HD720 or 1080, and regardless if its "finilized" first or not, or if its shared to "media library", the transitions is not working (un sync) and the sound is fading out to 0% during all the transitions before up to the original level.
I have for real exported the film more than 25 times and average export time is 6 hours due to the high quality and the time duration.
When just in the project view looking and listening, everything is just perfect. As soon as I finilize the project, or export it, even in the project preview it doesnt work. I also tested to install miDVD pro (10$) and WonderShare DVD Creator (39$) to just sharing the project to them, but the result was the same.
I just want to be able to export it as it is in the project.
I have macbook 13, moutain lion, iMovie 11
Any suggestions?
Thanks in advance!

I have iMovie '11 and cannot create a HD 1080p movie. I've got a 27" iMac with a 2.93 GHz Intel Core i7 processor (I purchased this computer last month). I tried like crazy to export the HD movie last night (it's one of the new trailers -- the one that looks like Indiana Jones & it's less than 1 minute long) but no dice due to a "HEAP" error. I tried to export the movie a couple of times this morning. It went a little further in the rendering until the HEAP error popped up again (this was from a fresh reboot). The really odd thing is that when I render it in HD 720p, my movie clips are black. No video. The built-in trailer stuff from iMovie '11 is there, just none of my clips show up (they're all black).

Adobe Application Manager Download Error (and other problems)

Last week I purchased a Creative Cloud membership (Student and Teacher Edition, if that matters at all). When I tried to download applications, the Adobe Application Manager seemed to be unable to connect and instead displayed "Download Error. Press Retry to try again or contact customer support." I read some of the responses to this problem on the forums, and after trying several things, I got it to work (I'm honestly not sure what I did that caused it to work). However, it is now failing to work again and I can't seem to fix it this time. As an additional problem, When I tried to open Adobe Premiere Pro (which I managed to download when I got the App Manager working for a while), I got the opening screen that asked me to open a project or start a new project. No matter what I clicked on, Premiere Pro closed with an error message. Just as with the App Manager (and at the same time), I managed to get Premiere Pro to work (it seemed to work after I set permissions so I thought I solved it), so I was able to use it for a day. However, now the problem has returned.
I don't know if these two problems are related, but they started working at the same time and stopped working at the same time, so I'm posting them together in case there is a connection. I am running Windows Vista on my home computer. I can sign on to the creative cloud online without problem so it recognizes me as a creative cloud subscriber. My Internet connection is working fine. I have disabled all firewalls and it still doesn't work. Very frustrating, obviously.
Thanks for your time and any help or suggestions you can give.
- KP

Kardypaine for your Internet configuration difficulties I would recommend reviewing Sign in or activation errors | CS6, CS5.5 Subscriptions, CS6 Perpetual - http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html.
For the failure of Premiere Pro to open you will want to review the install log to see if you received an installation error. You can find details on how to locate and interpret the installation logs at Troubleshoot with install logs | CS5, CS5.5, CS6 - http://helpx.adobe.com/creative-suite/kb/troubleshoot-install-logs-cs5-cs5.html.

Blue Screen and Sound Problems, In Desperate Need of Assistance

About a week and a half ago, my computer officially stopped showing anything on the display when I tried to start it up. It had been doing it on and off for a long time, but I would eventually get it to display. Not this time...
My husband and I took our 30" Cinema Display and G5 tower to the iStore. The display was tested, and it worked fine. The associate said the problem was the video card.
After doing much research, I decided upon the flashed GeForce 7800 GS, per the suggestions of japamac on this forum. After I received and installed it, the display worked again and everything seemed great! It came with a CD with a patch on it, saying it was for *10.4.9 or later*, so I installed the patch and ran the permissions command. I had to go on a business trip immediately as the permissions command was running, so I left the computer to do it's thing, knowing it would sleep after a while.
When I got back home from my trip, I eagerly hopped on my computer. I attempted to awake it from sleep, however it froze. I was not able to tell if the permissions command ever finished completely.
I restarted the computer and everything seemed fine. A few hours later, my husband hopped on the computer about to test the new card on a game, but it froze before he could do anything. We restarted the computer, and that's when the blue screen issue started.
I tried resetting the PRAM, starting it up on the install disc (which didn't work), I tried holding down the S key (which also didn't work), and I tried holding down shift for Safe Boot.
The Safe Boot works, in fact I'm on my G5 right now. I did the permissions command again, thinking that it must've not ran all of the way and the permissions were broken. When it finished it gave me a massive list of "permissions differ"s with 10 "Warning: SUID file "____" has been modified and will not be repaired" messages at the end.
I contacted the seller on ebay, who ended up telling me the patch was only for Tiger, despite the file saying "or later". I really thought I messed up the permissions badly from that and tried running the permissions repair, but that did not help.
Thinking I had no other choice, I backed everything up and I reinstalled Leopard (choosing to Archive). After it finished reinstalling, the computer restarted and it booted up normally. I thought my problem was solved! However, once I let it sleep and came back later, it was frozen. I restarted and had the blue screen problem all over again, to my disappointment.
I tried restarting, the PRAM, the permissions (which did not list those SUID warnings anymore)... There was once that I restarted and it gave me the blue screen, I tabbed twice, hit enter, and entered my password though I couldn't see anything. I heard the computer moving like it was logging in. I pushed the power button on my display, and magically the screen displayed my desktop with the "Are you sure you want to put your computer to sleep?" window.
However, this only happened once, and afterward I noticed an issue when I tried to wake the computer from sleep. It would try to wake up, then go back to sleep, try to wake up, go back to sleep... So I contacted the ebay seller again, explaining what had happened and that it made me think it is an issue with the card itself, not permissions. (Fearing that if it is permissions, I would have to reinstall the OS again, but choose to erase the disk this time.) I asked if the seller knew anything about this.
The seller contacted me back saying, "Hello again, yes, wake from sleep is a common issue of many modified cards for Mac , so you better turn it off if you are not use it, its better for both the video card and power supply of your G5,
hope you understand about it , thanks". Well, that really would have been nice to know in advance... but regardless, the more important issue is the blue screen on startup.
On top of all of this, when I tried to watch a video tonight I noticed the sound was not working. I made sure it wasn't muted, I made sure the optical cable was connected, nothing. I restarted, nothing. I did not have any problems whatsoever with the sound before this, and I'm not sure if it has anything to do with the card (I wouldn't think so), or that something needs to be reinstalled since I reinstalled the OS. The System Prefs > Sound, Is not finding any devices.
I've restarted the computer so many times since the initial failing of the video card, I really hope all of the restarting hasn't damaged anything. As old as my Mac is, it's been working perfectly normally until the graphics card went out. After that, it's seemed like everything is falling apart. Thank you for reading my long history of difficulties, and I hope someone (maybe japamac?) can help me!

Hi-
I understand why you would suspect the latest hardware addition, and the conflicting/misunderstood advice given by the seller isn't helping.
I don't know of any cards that have "known" issues with sleep from the flashed realm.
Of the 10 different makes and models that I use or have used, flashed by myself or others, I have never seen an issue with sleep.
This includes 2 different Geforce 7800 GS cards.
The most common reason for a blue screen at boot is an incompatible Login or Startup item.
These are disabled during a Safe Mode boot.
http://www.thexlab.com/faqs/startupitems.html
As for the Geforce 7800 GS, there was a patch for OS 10.4.9 only. This was to allow for the proper reporting and use of the appropriate OpenGL engine.
After 10.4.11, and in Leopard, the OpenGL engine is properly selected for the card.
Since this is simply a reporting issue, and not a performance issue, the patch is not a mandatory thing.
There is an issue with the ROMs used in some Geforce cards that causes a boot delay (a blue screen) for up to 6 minutes.
Most guys don't use those ROMs anymore, but I guess that someone may not have bothered to get the new ROM.
Removing the AppleHWSensor.kext from /System/Library/Extensions will correct this issue.
This, however, is historically a G4 issue only.
There are a couple possible scenarios that I think may apply to you:
1- The card is overheating, thus the occasional success or Safe mode only boots.
Check that the fan is spinning.
2- The auxiliary power is not connected, or has a poor connection.
Sometimes the pins on a Molex adapter (the female side) are so tight that they push out, rather than allowing the male pin in.
Conversely, a stretched out female pin would not properly contact the male pins of the graphics card.
Double check connections at the optical drive and at the graphics card.
While inside, reseat the graphics card.
3- If the card was prepared for use in a G4 by cutting the traces of pins #3 and #11, this can cause problems in the G5.
Most cards work fine, but some Geforce cards complain.
As well, if the pins were taped, the tape should be removed for use in a G5.
http://themacelite.wikidot.com/pins-3-and-11
If the traces are cut, return the card.
If the pins are taped, remove the tape.

SOLUTION to video and sound problems

I know this seems like a very long process, but it actually doesn't take too long (at least with music videos), and it's well worth having the audio and video ligned up properly. So hope it works for you all, let me know how it goes :)
i know a lot of people around are having problems with the video and audio not being together when using converters with mpg files. i've been trying different settings all day and i've come up with the conclusion that muxed mpg files WILL NOT have the audio in sync no matter what settings you use.
HOWEVER, you can download a small, FREE program VirtualDub (which can be downloaded at http://virtualdub.sourceforge.net/). (it requires NO INSTALLATION, which is brilliant)
so, once you've got this program opened:
1. first put your muxed video into there (drag it or "file>open file")
2. then go to "video>compression" and select "microsoft MPEG-4 Video Codec V2" and then press "OK".
3. after that, go to "file>save as AVI", select where you want to save it and then press OK.
NOW you have a non-muxed video file, that you can convert using any of the regular converters (Xillisoft, Videora.. etc.) Personally i use Xillisoft's IPod Video Converter, and ta da, you know have a correctly sync'ed audio and video file compatible with the ipod.
hope it helps everyone else
P4 Windows XP Pro
EDIT: oh yeah, and after you have your converted file using Xillisoft or Videora, you can delete the AVI file and keep the original if you want.

hmm.. ok.. well perhaps you might need the codec installed on your computer.. this is strange i thought it was default..
can you try telling me what options you do get in there? and i'll search to see if you can download it.. OR you can try just selecting another one, i think at this point it doesn't really matter which one, as long as you use one, because an uncompressed AVI is absolutly HUGE. so try another one from the list (preferabley one that says 'no known restrictions' i think) and let me know if the sound is still good after youthen convert again using videora or xillisoft

New layout, CSS errors and Firefox problems

Hi
Could it be that some of the Firefox problems are caused by:
1) The wrong mime type for the CSS files? Currently it appears to be:
application/x-css
shouldn't it be
text/css
2) Errors in the CSS files and inline CSS of.
http://forums.oracle.com/forums/categoryHome.jspa?categoryID=84
Can recommend using:
http://jigsaw.w3.org/css-validator/
==== New layout ======
The border error on the download button has been fixed, but the alt attribute of the upper right search icon is still "faq", shouldn't it be "Search"
<img src="images/search-16x16.gif" width="16" height="16" border="0" alt="Search">
Axel

There are a number of fixes still to be made, but most of them will wait until our upgrade (still a few months out).

Windows 7 and Wireless Mighty Mouse, Wireless Keyboard and sound problem

Hi,
I just installed Windows 7 x64 Ultimate on my iMac 24" white ( OS X Leopard 10.5 ). Surprisingly, it installed without any problems. The only problems I have now are the Wireless Mighty Mouse and the Wireless Keyboard ( alu ).
After I installed Windows I inserted the Leopard Instal DVD and installed Boot Camp. I got a message right away saying that: "This program has known compatibility issues...". I clicked Run program and continued. Soon I got the same warning, but this time not for Boot Camp, but Intel Chipset Device Software. I clicked Run program yet again and it continued installing. Then I got a different warning: "Service KeyAgent' failed to start. Verify that you have sufficient privileges to start system services." I clicked Ignore and installation continued. I got another "Service Mac HAL' failed to start. Verify that you have sufficient privileges to start system services." warning, clicked Ignore again and after that it finished soon and I restarted the computer.
When I came back into Windows there was no Apple folder anywhere or any sign that I have just installed Boot Camp ( should there be? )
I installed Boot Camp Update 2.1 for Windows XP ( because Vista x64 version wouldn't start ) and basically I got the same warnings I did when I installed Boot Camp from the Leopard DVD ( described above ). I also tried to instal Boot Camp Update 2.2 for Windows, but it didn't start. I also downloaded Bluetooth Update 1.0, but all I got was a message saying: "This update is not intended for this computer and will not be installed.".
There is also no sound.
This is basically it, I really hope some of you who run Windows 7 with wireless keyboards and mice can help me, because I desperately need this to work ( I use a Windows only program for school ).
PS. I have a 2007 iMac 24" white and while it is not on the we're-not-supporting-that list for the infamous Windows 7 Boot Camp update, all other iMacs from its generation are. Any ideas?

Found a solution for the "Boot Camp x64 is unsupported on this computer model" message. Here is the link: http://www.techulous.com/hardware/how-to-apple-boot-camp-64-bit-for-windows-7-on -unsupported-macs.html
Everything works ( for ) now. Yay!

CRC Errors and Sound Problems

Similar Messages

Maybe you are looking for