CRIO-9067 Real-time unexpected error restart (Hex 0x661)

Hi all,
I recently moved to LV2014 SP1 and NI-RIO 14.5 to support development of a cRIO-9067 Linux RT controller. The past two days of development have seen LabVIEW crash numerous times (eight at last count), along with numerous VIs being in an undeployable state due to some unseen error (there's no broken run arrows anywhere, and a LV restart seems to cure what was broken).
The above issues are tolerable, if somewhat annoying. What's concerning is the most recent error I received this morning. I had just run the top level VI from source (and verified it was running), went to make myself a coffee and came back to this error.
LabVIEW: (Hex 0x661) The LabVIEW Real-Time process encountered an unexpected error and restarted automatically.
The VI wouldn't have been running for more than 10 minutes. I've since tried to reproduce the error without luck.
This is somewhat concerning as the application for this cRIO will be 24/7 process control. Is this a known issue with the newer Linux RT controllers? Is there anything that can be done to detect the error in LabVIEW?
Below is a screenshot of the software installed on the controller:

You should be able to access the error logs on your controller through MAX.
Is There an Error Log File for My Real-Time Controller?-http://digital.ni.com/public.nsf/allkb/E734886E027D0B6586256F2400761E30?OpenDocument
How Do I Locate the Error Logs on My cRIO if I Don't Have MAX? - http://digital.ni.com/public.nsf/allkb/9D2F9D4F8C834D678625766D00633837
Could you post the error log files for the Compact RIO targets that reproduce the error?
It’s possible that a memory leak is occurring someplace in your program that causes the crash.
Also, are you using the System Config Set Time.VI anywhere in your application? There has been a reported issue with this VI in relation to this error, but the hex code error is not common. We can try to cross-compare the issue internally to see if there are simlarities to the reported case.
Additionally, is this crash repeatable with other code, say a simple shipping example? I would imagine that the crash is related to a routine called in your program, but it’s possible there is a corruption in the software installation on your target.
Also, what is the ProcessCommandMessage.vi responsible for/doing in your application?
Will M.
Applications Engineer
National Instruments

Similar Messages

X121e randomly wake up from suspended status and real time clock error

Hi all
Previously I considered my x121e suffer from overheating issue and causes real time clock error (RTC). However, after more testing and investigation, I believe the problem is related to other hardware issues and I like to hear people opinion before sending the laptop back to Lenovo.
The machine goes into suspend status either pressing the power button or closing the lid from Windows7 (clean install) without problem. However, it would wake up itself randomly, "beep" twice and screen shows RTC and CMOS checksum error. This happen more often when I am holding the machine (i.e. some movement/vibration). I wonder:
- Is it the RTC battery problem, cause the RTC to wake up the machine?
- Other hardware failure?
The laptop has a clean OS installed/recovered. Latest 1.16 Bios installed. No USB or memory card attached. Ram replaced and not the cause.
Please advise
Howard

Hello,
I am unsure; you would have to contact Lenovo directly and find out how they handle this situation. They may want the ThinkPad X121e back so they can run thorough diagnostics on it, just in case the problem is something else. That way it gets fixed the first time.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Error: 0271: Real Time Clock Error - Check Date and Time settings.

Hello all,
I have lenovo T430s laptop that is configured with Bitlocker encruptions and TPM PIN entry. I don't think that has anything to do with the error msg I am getting but here it is. Error: 0271: Real Time Clock Error - Check Date and Time settings.
Press Esc to continue or F1 to enter setup. I am unable to get into BIOS or even the login screen for Windows 7.
Any advice would be appreciated.

Thanks to everyone for the help. Just want to close this out. I had a IBM/Lenovo technician here today and he replaced the CMOS battery. Upon the change, the computer is fine being reconnected to the dock (the three times I tried it). So it has been resolved with the battery. Surprised by the incompatibility claim because I am not having issues now. Wondering if it's just a USB 2.0 vs. 3.0 thing (and Lenovo trying to sell more peripherals, of course).
Thanks!

Real Time Clock Error - Check Date and Time settings, System CMOS Checksum bad

Hello everybody,
Can help anyone to resolve my problem.
I have an Thinkpad W520 (42823FG), BIOS 8BET60WW 1.4 When I disconect AC power and remove battery and connect again, I see this message on screen:
"Real Time Clock Error - Check Date and Time settings, System CMOS Checksum bad
Press Esc to continue or F1 to enter Setup"
Is this a system board problem or CMOS battery problem ?
Thank you

Hello and welcome,
It's probably (hopefully) just the CMOS battery. The easiest way to find out is to just replace that battery.
Page 85 of the Hardware Maintenance Manual:
Hardware Maintenance Manual
Here's an example of the battery. I'm not recommending (or not) this vendor:
http://www.ebay.com/itm/New-Lenovo-ThinkPad-W500-W510-W520-W530-W700-W701-W701ds-CMOS-RTC-Backup-BAT...
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Hypervisor: Create Standalone Real-Time Application (Error at deploying: File not found)

Hello,
I am using Hypservisor. With "Build Specifications" in the project explore I want to create a standalone real-time application.
In my first try I only want to print some texts onto the real-time console (HyperTerminal) using the function "RT Debug String.vi". I built the real-time application successfully and got the rtexe-file locally on the windows system. But as I tried to deploy the application to the target system, I got the error: "File not found". Please check the attached file "error.txt" for details.
I don't understand which file is not found. Or I used "\" as path separators. Is it wrong? I'd appreciate if you'd have any idea of the problem. Thank you very much.
Regards,
Scarletice
Solved!
Go to Solution.
Attachments:
ERROR.txt ‏1 KB
builds.zip ‏153 KB

Hello Casey,
Thank you very much for your reply and your interest in our project. We are using Real-Time Hypervisor for the setup of our test stand. We use the Windows system to show the GUI and the Real-Time system for the real-time machine control and online data storage. We use shared variables and shared memory for the data exchange between the two systems.
The system works generally quite fine now. But we still have to face new problems at each step forwards. I'm sure, I'll have more questions. I'd appreciate your advices. Thanks sincerely.
Best regards,
Scarletice

.vi's unable to run because of real-time Startup error

See that attached files for the error. Whenever I try and deploy the code onto the robot the attached error comes up. Is there any fix for this or is this a new error? I have also tried a completely new C-Rio project so that it is the basic settings that FIRST gives us. This same error comes up with that one also so I am thinking it is a computer problem on my end.
Attachments:
Error part 1.JPG ‏30 KB
Error part 2.JPG ‏14 KB

It sounds like there is a start up application already on the cRIO that has different versions of these VIs as dependencies. I'd recommend turning on the NO APP setting on your cRIO. Depending on which cRIO you have this will either be a hardware switch on the cRIO or a setting you can change in Measurement and Automation Explorer.
Miles G.
National Instruments
Applications Engineer

How To Re-Compile ONE Component in Real-Time Without CF Restart?

Is there a way?
I've seen tricks for restarting the application, but I suspect this still kills all active sessions, and we have quite a few going on.
I just have one CFC I need to recompile to get some changes in place, but I don't want to upset the entire apple cart.
Is there a way?
RLS

I like this idea and will give it a shot next time for sure. It would be so nice to find a way to do that without having to restart CF in Production to make a hotfix.
I will review those settings to see what the impact might be. I wouldn't want to affect long-term efficiency for short-term occasional satisfaction.
BKBK, thank you very much for your help and suggestions!
RLS

I cant open Photos om my mac. Just upgraded to Yosemite. The message I get is: An unexpected error has occurred. Please quit and restart the application. I have done this several times but nothing seems to work. iPhoto is gone. What do I do?

I just upgraded to Yosemite on my mac from 2010. Everything seems to work, accept Photos. When I try to open it i push the "Get started" button, then the picture with "Preparing Library" comes up. Then a message appears with the text "An unexpected error has occurred. Please quit and restart the application." I have done this several times, but nothing happens. What do I do?

I just upgraded to Yosemite on my mac from 2010. Everything seems to work, accept Photos. When I try to open it i push the "Get started" button, then the picture with "Preparing Library" comes up. Then a message appears with the text "An unexpected error has occurred. Please quit and restart the application." I have done this several times, but nothing happens. What do I do?

Error -1074384569; NI-XNET: (Hex 0xBFF63147) The database information on the real-time system has been created with an older NI-XNET version. This version is no longer supported. To correct this error, re-deploy your database to the real-time system.

Hello
I have a VeriStand-Project (VSP) created with my Laptop-Host (LTH) which works with my PXI, while
deploying it from my LTH. Then I have installed the whole NI enviroment for PXI and VeriStand use on a
industrial PC (iPC). I have tried to deploy my VSP from the iPC to the PXI but the following error
message arose on my iPC:
The VeriStand Gateway encountered an error while deploying the System Definition file.
Details: Error -1074384569 occurred at Project Window.lvlibroject Window.vi >> Project
Window.lvlib:Command Loop.vi >> NI_VS Workspace ExecutionAPI.lvlib:NI VeriStand - Connect to System.vi
Possible reason(s):
NI-XNET: (Hex 0xBFF63147) The database information on the real-time system has been created with an
older NI-XNET version. This version is no longer supported. To correct this error, re-deploy your
database to the real-time system. ========================= NI VeriStand: NI VeriStand
Engine.lvlib:VeriStand Engine Wrapper (RT).vi >> NI VeriStand Engine.lvlib:VeriStand Engine.vi >> NI
VeriStand Engine.lvlib:VeriStand Engine State Machine.vi >> NI VeriStand Engine.lvlib:Initialize
Inline Custom Devices.vi >> Custom Devices Storage.lvlib:Initialize Device (HW Interface).vi
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * • Unloading System
Definition file... • Connection with target Controller has been lost.
The software versions of the NI products (MAX/My System/Software) between my LTH and the iPC are
almost the same. The only differences are:
1. LabView Run-Time 2009 SP1 (64-bit); is installed on LTH but missing on iPC. The iPC has a 32-bit system.
2. LabView Run-Time 2012 f3; is installed on LTH but missing on iPC.
3. NI-DAQmx ADE Support 9.3.5; something strage on the LTH, because normally I am using NI-DAQmx 9.5.5 and all other DAQmx products on my LTH are 9.5.5. That means NI-DAQmx Device Driver 9.5.5 and NI-DAQmx Configuration 9.5.5.. On the iPC side all three products are 9.5.5.. That means NI-DAQmx ADE Support 9.5.5, NI-DAQmx Device Driver 9.5.5 and NI-DAQmx Configuration 9.5.5..
4. Traditional NI-DAQ 7.4.4; The iPC has this SW installed. On the LTH this SW is missing.
In order to fix this problem I have formatted my PXI and I have installed the following SW from the iPC:
1. LabVIEW Real-Time 11.0.1
2. NI-488.2 RT 3.0.0
3. NI_CAN 2.7.3
Unfortunately the above stated problem still arose.
What can I do to fix this problem?
I found a hint on http://www.labviewforum.de/Thread-XNET-CAN-die-ersten-Gehversuche.
There it is written to deploy the dbc file againt.
If this is a good hint, so how do I deploy a dbc file?
I would feel very pleased if somebody could help me! :-)
Best regards
Lukas Nowak

Hi Lukas,
I think the problem is caused by differenet drivers for the CAN communication.
NI provides two driver for CAN: NI-CAN and NI-XNET.
NI-CAN is the outdated driver which is not longer used by new hardware. NI replaced the NI-CAN driver with NI-XNET some years ago, which supports CAN, LIN and the FLEXRAY communication protocol.
You wrote:
In order to fix this problem I have formatted my PXI and I have installed the following SW from the iPC:
3. NI_CAN 2.7.3
NI CAN is the outdated driver. I think that you should try to install NI-XNET instead of NI-CAN on your PXI-System, to get rid of the error message.
Regards, stephan

CRIO: error while compiling real-time application

My code can be run when the cRIO is connected to PC with Ethernet cable.
But when I want to compile (build) my code, I get the following massage.
Also the picture of the massage is shown below.
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
Error 6 occurred at Copy in AB_Targetfile.lvclassostBuild.vi->AB_Application.lvclassostBuild.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: Generic file I/O error.
E:\2013_05_23a_research\2013_05_27a_Richard's\exercise\2013_07_07_exampleFinder_1DMAFIFO\examples\CompactRIO\Module Specific\NI 9234\builds\NI 9234 Getting Started\NI-cRIO9024-UConn\My Real-Time Application\c
Solved!
Go to Solution.

Hi Cashany,
What version of LabVIEW Real-Time are you working with? What cRIO are you deploying to? What version of the NI-RIO Drivers are you using?
Behind your error dialog you have a Load Save Warnings dialog. What is the full expected path that LabVIEW is expecting to find this VI at? Have you tried correcting this conflict by moving the file to the expected path or changing your project to expect it from the new path?
Also I notice that the paths that are listed are rather long. Is it possible that your problem is related to this KnowledgeBase, Error 6 Occurs at Create Folder When I Build my Real-Time Executable?
Miles G.
National Instruments
Applications Engineer

I have tried to install Windows 7 Beta multiple times, but I always get the following error statement while copying temporary files or just as "Setup is starting" is displayed: "Windows Setup experienced an unexpected error. To install Windows, restart t

Restarting the installation results in the same error message. Any ideas on what's wrong? Here are some details:
my computer is lenovo g585.
I am running windows8. It's licence will be closed in one week.
I have windows7 OS genune.
While installing this (with sandisk pendrive ) the unexpected error occurs.
I am using avast antivirus, I have turned off this while installing.
So any help or suggestions would be greatly appreciated!
Thanks in advance!

Is OS already installed on your HDD?
Check this link : http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-setup-experienced-an-unexpected-error-to/e28d6f6e-7afc-4ad8-ae99-a92f90cf9083
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

HT3728 When I reconnect my Time Capsule after a factory reset, the Airport Utility shows ther message"Unexpected error. Try again." I also get this if I redo the factory reset.

The Time Capsule is not providing a wireless connection.
When I reconnect my Time Capsule after a factory reset, the Airport Utility shows ther message"Unexpected error. Try again." I also get this if I cancel the Airport Utility app and restart it. I performed the factory reset again, restarted the Airport Utility and received the same error. What are the steps to debug and fix the wireless problem?
My Time Capsule is connected to my FIOS router and to my Mac Mini. I am still able to connect to the Internet from the Mini via ethernet. It seems that the Time Capsule acts as a bridge for the ethernet connections between Internet to FIOS, FIOS to Time Capsule, and Time Capsule to Mac Mini.

Which model TC is this? The A1xxx number from the base please.
Try the setup in full isolation from the network.. so unplug the TC from the network.. and turn off wireless in the mini.. so you have mini--ethernet--lan port TC.. and nothing else.
Do the factory reset.
Now check if TC comes up in airport utility..
If it fails, turn on ipv6 local link.. if you are using 6.3 utility this could be necessary.
Still fails, try loading the v5 utility.. you will need to plug the computer back into the FIOS to get internet. Then depending on OS.. Lion according to your profile.. you can just down the utility.. ML takes more steps.
See below.
Do you have an iphone or ipad.. download the airport utility app and use those for the setup.. that can sometimes work better.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 (now 6.2 if you updated) so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0

I tried updating iTunes to version 11.1.1, but installation fails each time even when I did it manually as was suggested. The message I receive is: "The installer has encountered an unexpected error installing this package. This may indicate a problem"

I tried updating iTunes to version 11.1.1, but installation fails each time even when I did it manually as was suggested. The message I receive is: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."

Hi hongkongpom,
Just wanted to say that after posting the problem, I had a chat with an iTunes' Tech Support, her name is Rebekah. My problem was resolved after that. Will list the chat history below in hopes that it may help you as well.
Good luck!
Samia
Chat Transcript
Friday, October 4, 2013 05:55 AM
Duration: 81 minutes 28 seconds
Rebekah:
Welcome to AppleCare chat support. Please give me a moment to look over your information.
Rebekah:
Hi, Samia! My name is Rebekah. If we get disconnected, please chat us back. http://www.apple.com/support/ipod/contactEnter the case number from the initial email we sent you. This gives the next advisor you chat with immediate access to your case history.
Rebekah:
Could you please confirm your serial number? I want to be sure we provide the best service possible for you, Samia!
SAMIA:
Sure, it's 8L8395UY2C5
SAMIA:
My problem is with iTunes.
Rebekah:
Thanks for that confirmation. Just a heads up, this is iOS Tech Support. We do support iPod touches, iPads, and iPhones, but not the iPod classic. But no worries! I can get you in touch with a phone Advisor who can get you in touch with the department that specializes in iPod classics and would be able to better assist you. Would that be OK?
SAMIA:
I wasn't able to install the new version of iTunes (version 11.1.1). The installation keeps failing. The they suggested the I install it manually and that failed too. I will attach the message I received.
SAMIA:
I don't have a problem with iPod.
SAMIA:
Just iTunes
Rebekah:
No problem! We can certainly troubleshoot iTunes as much as possible. It may come to the point that you may have to transferred, but we can do as much as possible during this chat!
Rebekah:
Thanks for the screenshot. It is a bit small so I am unable to fully see the message that you are receiving. What is the error message you are receiving?
SAMIA:
This is the message I received in case you weren't able to open the attachment: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."
Rebekah:
Thanks for that info!
SAMIA:
Pleasure!
Rebekah:
What version of Windows (XP, Vista, 7) do you have?
SAMIA:
Windows 7
SAMIA:
Windows 7 Home Premium
Rebekah:
Thanks for that confirmation. I do apologize for the delay, Samia. I am researching this error code now. You mentioned trying to install iTunes manually. To be sure I am on the same page, what steps did you take to do that?
SAMIA:
Well when the indsatalltion failed I was given instructions to select Download Only from Tools and then install manually. When I did it, I window popped up with the following items: - AppleApplicationSupport
SAMIA:
- AppleMobileDeviceSupport64
SAMIA:
- Bonjour64
SAMIA:
iTunes64
SAMIA:
SetupAdmin
SAMIA:
I selected Repair in all of them instead of Remove and all worked but iTunes64
SAMIA:
That's when I received the message that I sent you earlier.
SAMIA:
By the way, this is the fir st time something like this occured. I never had problems with installation before.
Rebekah:
I completely understand what you're saying. Since that Repair did not resolve the issue, our best option is to uninstall iTunes and its components and redownload it. To do this, we will follow the steps in this article: Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
Rebekah:
First, we will want to quit iTunes and/or Apple Software Update if those are open at this time.
SAMIA:
Rebekah, the instructions you gave says, "For Windows XP, follow these steps to remove and reinstall iTunes and other software components for Windows XP."
SAMIA:
I closed all applications
SAMIA:
Also, my iTunes doesn't open anymore after the new failed installation.
Rebekah:
The section that says "For Windows XP…" is in case we opened up the wrong article, as we have the one for Windows Vista, 7, or 8. There is a link to click ("these steps") in those directions that would take us to the article for uninstalling on a Windows XP.
Rebekah:
So no worries! We have the right article!
Rebekah:
On the computer, we will want to click on Start > Control Panel. In Control Panel, we will click the "Uninstall a program" link.
SAMIA:
I thought so after doing a little exploration.
SAMIA:
done
Rebekah:
Alright, we'll want to select iTunes from the list of currently installed programs. Then we will click Uninstall. When asked if you would like to remove iTunes, let's click Yes.
Rebekah:
After the uninstallation is complete, we don't want to restart your computer if you're prompted.
SAMIA:
Done
Rebekah:
Then if you see other iTunes entries on the list, we'll want to remove them the same way.
Rebekah:
Then we will remove all instances of Apple Software Update the same way you removed iTunes.
SAMIA:
Okay, but do I have to remoce iCloud as well?
SAMIA:
Rebekah, I received the same error message again when uninstalling
Rebekah:
We actually do not need to remove iCloud. After the Apple Software Update, we will want to remove all instances of Apple Mobile Device Support
Rebekah:
How strange! Are you able to click past that and allow the process to continue or has it stopped it completely?
SAMIA:
I am unable to uninstall iTunes either
SAMIA:
Stopped completely
SAMIA:
I treied clicking Repair
Rebekah:
Alright, after trying the Repair option, let's see if it will allow us to continue uninstalling or not.
SAMIA:
I tried that but unfortunately, it isn't working. I still get that same message with error code 2324.
Rebekah:
This error code is not something that I am finding in my sources, Samia. So there is a chance that it is being caused with the Windows computer itself. However, I did find a link that may be able to help with uninstalling iTunes from Windows' support site: http://support.microsoft.com/mats/Program_Install_and_Uninstall
SAMIA:
Rebekah, you're a genius! It worked! iTunes is no longer there. What next?
Rebekah:
Awesome! I'm glad that worked!
Rebekah:
To be sure I am on the same page, what was the last component we uninstalled?
SAMIA:
iTunes
SAMIA:
Shall I remove the Apple Application Support, Apple Mobile Device Support, and Apple Software Update
Rebekah:
That is correct! However, we do want to uninstall it in the order I mentioned above. So Apple Software Update first, Apple Mobile Device Support next, and then Apple Mobile Device Support.
SAMIA:
Got it, but is the second one to uninstall Apple Mobile Device Support OR Apple pplication Support?
Rebekah:
The second one is Apple Mobile Device Support.
Rebekah:
The Application Support will be the last component we uninstall.
SAMIA:
Thanks! I'm on it.
SAMIA:
Done! ll 3 are gone, well 4 with iTunes. Now what?
Rebekah:
Awesome! Also, I just noticed that I accidentally typed Apple Mobile Device Support twice, I do apologize for any confusion! Now we will remove all instances of Bonjour and then remove all instances of Apple Application Support.
SAMIA:
There was only 1 instance with Bonjour. I don't know what the instances are for Apple Application Support
Rebekah:
Yes, Bonjour is often only listed once. Is the Apple Application Support listed at all?
SAMIA:
No
SAMIA:
Since I removed it
Rebekah:
Oh, perfect! If it was removed, we should be set!
Rebekah:
We have removed iTunes and its components now! From here, our next step is to restart the computer. Then once you reboot, you can redownload iTunes from apple.com/itunes
Rebekah:
That should allow you to download iTunes!
SAMIA:
Shall I downloaad the latest vesion?
Rebekah:
You will want to first restart the computer as shown in the article. That will ensure that this process goes smoothly and that everything was removed correctly! Then you can try downloading iTunes again.
SAMIA:
Okay, thanks Rebekah!
Rebekah:
You're very welcome! I'm glad I could help! And of course if you have any issue after the reboot and download, you can always chat us back, as chat is open 24 hours! You will just need to give your case number and the next Advisor would have all my notes!
SAMIA:
Thanks again for all your help, for I couldn't have managed with out it. Have a nice day!
Rebekah:
You're very welcome! I know how important iTunes is and I'm glad we could get you on a path to resolution!
Rebekah:
I hope you have a lovely day!
Rebekah:
It's been a pleasure speaking with you! Thanks for chatting with us Samia. If you don't have any more questions, select End Chat from the upper left corner of the chat window.
SAMIA:
Will do, thanks.

Error in Real Time Collaboration

Hi
We got an issue in our project.
When ever any user log's into Portal it is giving a message called
With title Real-Time Collaboration(You are logged to the same portal already. Real-time collaboration capabilities will not be available in the current portal session until you terminate the other session and then restart this one by refreshing the browser or logging on again.)
We are using EP6 SP13
And we are having 2000 Portal users every one is getting this error in portal.
And After restarting the Server we are not getting that error. And again after a month it again starts.
Thanking you in advance for help
From
Srikanth

Hi Srikanth,
We also faced the same error and it was because the same users have already logged into the portal once or more than once.
The capabilities of real time collaboration feature might not work if an user has made multiple login to the portal using same id.
Hope the issue should be same with you.
With regards
Deepa
Plz reward points for helpful answers.

Help? I keep getting "Unexpected Error" everytime I try to use my new Airport Express to extend my network from my 500GB Time Capsule.

I am trying to extend my network from my 500GB Time Capsule using the new Airport Express I just bought, but no matter what I try I keep getting "Unexpected Error. Try again". The Express is still flashing Amber. I cannot get it to turn green. What am I doing wrong here? Please help me.

Locate the AirPort Express in the same room as the Time Capsule for the setup.
Power off and restart the Time Capsule
Shut down and restart the Mac. Turn on the wireless on the Mac and temporarily disconnect the Ethernet cable from the Mac to the AirPort Express. In other words, you want to set up the AirPort Express using wireless, since that is the way that it will be used.
Hold in the reset button on the AirPort Express for 9-10 seconds and release. Allow a full minute for the Express to restart.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click directly on AirPort Express.
AirPort Setup will open up and take a minute to analyze the network, then announce that the Express will be configured to extend the Time Capsule network.
Enter a device name that you want to use and click Next
Wait a minute while AirPort Setup configures everything, and hopefully announces a message of Setup Complete. Click Done.
Now move the AirPort Express to a location that is about half way between the Time Capsule and the area that needs more wireless coverage. Avoid obstructions in the signal path between the Time Capsule and AirPort Express as much as possible.
Walls, ceilings, mirrors, heavy furniture, etc. just kill the wireless signal quality. Keep any cordless phones as far away from either router as possible.
It would be much better if you could plan to connect the Time Capsule and AirPort Express using an Ethernet cable, as best case.....you will be losing about half of the network speed trying to use wireless to extend.

CRIO-9067 Real-time unexpected error restart (Hex 0x661)

Similar Messages

Maybe you are looking for