CUA restore user data after system refresh

We recently copied our PRD ECC6 system to DEV.  In the new DEV, a client (client 301) was created by way of a client copy to replicate the environment prior to the refresh.  This new client has only one user - the CUA user for the CUA RFC.
Our CUA resides in an independent system.  The user and authorisation data for client 301 exists in the CUA.  How do I, or even can I push the user and authorisation data from CUA to client 301 on DEV?

Report RSCCUSND in the CUA system will allow you to push out data to the child system.  You may need to manually re-create user groups in the child system for this to work.

Similar Messages

  • Is there a process/program  to update tables/data after System Refresh?

    We are planning a refresh of SAP R/3 47 and SRM EBP 4.0. Copies of all data from our production system will be refreshed onto our test environment. 
    Is there a program that can be run to reset the "Destination" targets as there is with "source" using BDLS?
    We can copy out certain tables and reimport, but we fear that we may be missing something. If anyone has informatoin on the process for performing a refresh, we would appreciate hearing about it.
    Thanks,
    BIll
    Message was edited by: William Olliver
    Using BDLS and clearing out some of the custom tables (allowing normal programs to rebuild data points) did the trick. 

    Hi Bill,
    BDLS takes care of the table entries that correspond to the Logical System.  This takes care of almost 80-90% of the entries. 
    Keep in mind however, you will need to change all the entries that correspond to an backend RFC destination or other webservers once a copy is made; as those are not updated by BDLS. 
    Some of these are (as it is entirely dependent on the scenarios being implemented):
    DEFINE BACKEND SYSTEMS:
    --IMG>SRM>...
    ORGANIZATION STRUCTURE
    --Use standard program RHOMATTRIBUTES_REPLACE
    --Plus, Change other attributes: POrg,PGrp,Plants...
    EDI/IDOC/ALE entries for partner profiles
    --WE21 etc.
    TWPURLSVR, TWPURLPATH, etc
    --Table entries
    WORKFLOW Verification Steps
    --IMG>Workflow...
    MIDDLEWARE PARAMETERS in R/3 and SRM.
    --Table Entries
    CATALOG ENTRIES
    --IMG>Master Data...
    Hope this helps.
    -Sachin Sethi

  • Logical System Conversion after system refresh failed

    Hello,
    Logical System Conversion after system refresh couldn't complete as the printer was locked. This job was run in the background. In SM37, the  job log of RBDLSMAP shows as job finished, but it took only 40 seconds. Now I see that the logical system got changed(Converted) in the client settings scc4 but I know that this client being a production client and would run for couple of hours. Here is the job log information.
    02/18/2009 16:09:33 Job started                                                                     00           516          S
    02/18/2009 16:09:33 Step 001 started (program RBDLSMAP, variant &0000000000000, user ID ABCD)      00           550          S
    02/18/2009 16:09:33 Output device PRN1 is locked in the SAP system                                  PO           349          I
    02/18/2009 16:10:19 Job finished                                                                    00           517          S
    When try to rerun bdls again, it shows that it is already available and it says "The new logical system name is already assigned to the current client".
    Any suggestions on this?
    Thanks,
    Mahesh

    Hi ,
    Rerun the BDLS again as this took very little time.
    When you try to run again it popsup message saying it already exists just delete that and again put the Logical system name and run it will run that time.
    May be while scheduling the job you gave for spool I am not sure why is it looking for Printer which is locked.
    Thanks.

  • Acct assignment cat. of item not in user data; Inform system admin

    Hi all,
    We are on a SRM EBP 5.0 project and we are getting the following error when we try to create a purchase order from the purchasers login.
    "Acct assignment cat. of item not in user data; Inform system admin"
    The complete details of the screen shot are as follows:
    The following error text was processed in the system DS1 : Acct assignment cat. of item not in user data; Inform system admin.
    The error occurred on the application server lndnysap1_DS1_01 and in the work process 0 .
    The termination type was: TH_RES_FREE
    The ABAP call stack was:
    Form: ABORT_PO of program SAPLBBP_PO_UI_ITS
    Form: ADD_TO_MSG_LOG of program SAPLBBP_PO_UI_ITS
    Form: ADD_TO_MSG_LOG_MULTI of program SAPLBBP_PO_UI_ITS
    Form: SET_PRICING of program SAPLBBP_PO_UI_ITS
    Form: DETERMINE_EXTERNAL_SCREEN of program SAPLBBP_PO_UI_ITS
    Module: DETERMINE_EXTERNAL_SCREEN of program SAPLBBP_PO_UI_ITS
    We did the following steps :
    Created shopping cart- employer and WF triggered apprd. by manager.
    Purchaser did "Carry Out Sourcing ", and if we say "Create Purchase Order", the PO gets created with a information message that "Incomplete purchase order 11/1 is created "
    When we go to  "Process Purchase Order" for the completion of the same. If we see Follow-on documents "Purchase Order Held" occurs.
    In the tab Item Data details Pricing tab we get this error.
    Do any of the SRM gurus can suggest us what to do?
    In our admin logon it shows
    "Server for pricing is not running. Start Server"  occurs after every run of this process purchase order from the purchasers login, though our IPC is working fine.
    Will be of great help if somebody replies soon.
    Sincerely,
    Sridhar.

    Hi,
    IPC has to be configured.
    Please check the following threads :
    https://forums.sdn.sap.com/click.jspa?searchID=211089&messageID=2714527
    https://forums.sdn.sap.com/click.jspa?searchID=211089&messageID=2715019
    Kind regards,
    Yann

  • SAP License issue after system refresh.

    Hi,
    After system refresh, refreshed system has License info of source system. When trying to apply license from unix, it gives below error, saying system number is incorrect to apply new license. Looks the system number of source system is causing issue. I checked, there is no data in MLICHECK table. I could see some info in "saplikey" table. System is 700 system.
    sidadm> saplikey -install "/home/SID/sid_multiple.txt pf=/usr/sap/SID/SYS/profile/SID_DVEBMGS01_sapsidci
    This system's system number is "000000000710287641", but there is a license key
    for system number "000000000711311441" in file "/home/SID/sid_multiple.txt".
    sidadm>
    Thanks.

    First check whether you have deleted all invalid licenses?
    use below command to delete invalid licenses
    sidadm>saplicense -delete
    And apply new license based on new hardwarekey with below command
    sidadm>saplicense -install
    *I think there should be some invalid licenses lying in your system
    Regards
    Nick Loy

  • After System Refresh Variants missing

    Hi,
    We have used Export / Import method to build QAS system from production
    ABAP export file.
    After System refresh we got the same Production client with all
    configurations, Variants, Object including data.. Which is Perfect.
    But, as per our business we don't want to use the same production
    client number in Quality System., so we done Cliet Copy to copy to
    different client (ex: Client 200) using SAP_ALL profile.
    Question: But after client copy we found that some Data, Objects,
    Variants are missing in the new client (200).
    Ex: In Client 100 (Copy of production client) table T009 is having 10
    entries, but after client copy in client 200 the same table doesn't have any
    entry in that including standard and Z.
    Please help me on this, how do I get clone / copy of 100 client
    (original client)
    Thank You,
    Ramesh

    Hi Ramesh,
    Looks like your client copy didn't bring all the data and Objects, Did you checked logs, Is there any error message ? The client copy completed with all the tables ?
    You can try Remote client copy method .
    You can manually export the variants from the source client to Target client and you need to export the Variants from the table VARID, VARI, VARIT and VARIS.
    You can use the below forum procedure to export and import variants.
    how to export RFC destination to file in order to import it in an other sys
    Since, not only the variants you are missing data and Objects, I would suggest for re-copy the client.
    Regards,
    Arjun

  • I want to restore my data after my pad was reset, but the latest backup was 5 months back. What can I do?

    I want to restore my data after my pad was reset, but the latest backup was 5 months back. What can I do?

    There is nothing that you can do. If you don't have a more recent backup, you can't magically create a current backup now. You can use the 5 month old backup, or simply start all over again. You can download most of your purchased content again as long as you use the same Apple ID that you used to make the purchases.

  • Lost Quickbooks data after System Recovery

    Is there anyway to recover Quickbooks data after system recovery?

    Quickbooks is an accounting tool designed and marketed by the Intuit Inc. mostly used for financially-related processes anywhere in any big or small organization. So, financial means quite important and very useful data to store..so there are number of possibilities of QBW file or QuickBooks database corruption.
    Read More:  http://www.filesrecoverytool.com/quickbooks-recovery.html
    use free trail version demo

  • Restore periodic batch job after system refresh

    Hi all
    I am going to do a system refresh and is there anyway to restore my periodic batch jobs after the system refresh or i need to reschedule all of them manually.Thanks in advance.

    You'll need to do them manually.
    Regards
    Juan

  • Restore SECSTORE security store after system refresh?

    When we refresh a QA system from PRD, we first export the RFCDES table from QA, then perform the homogeneous system copy from PRD -> QA, and then import the RFCDES table we saved prior to the copy.  This restores the various RFC destinations in the QA environment.
    In recent releases, the password information has been moved out of the RFCDES table into the Secure Store; it looks like this is based on tables RSECTAB and RSECACTB.  However, when we transport the contents of these tables and then bring them in again after the refresh, the RFC destination passwords are still marked invalid.
    Has anyone refreshed a QA system while saving the RFC destinations, using the secure store?  If so, how?
    Thanks,
    Rich

    Hi ,
    As an initial check , please check for error/informaiton on Kernel.
    OSS notes 816861 & 522536  will help you.
    Regards
    Nagaraju

  • How to recover backup user data after a restore

    I had a disk fail and could not boot. while in the restore software I was able to backup user data to a USB drive. Now that I've restored from the restore partition and got it running windows 7 home again, I don;t see how to recover the user data made with the low level software. Windows back up doesn't seem to recognise it and I can't find an HP utility to get at it.
    A program saved with the .wim back up files brought up an HP restore manager application that then copied the filed to my new C drive but how do I actually get it to recover them into their appropriate places and recreate users etc.
    Or, should I just consider myself lucky to still have copies of the files at all?  I'll not be real happy about that because it will be a tom of work to recreate everything manually even with the files.
    I'm hoping someone out there has a better solution for recovering all my user data into my new restored initial image.
    thanks,
    -dcb

    Hello dcbrower, You may be able to use the program Universal Extractor to extract the files in the .wim file.
    This is a Free program that can be found at this  Link. .
    Just extract the files in the wim file to a location you would like.
    Please click the White Kudos star on the left, to say thanks.
    Please mark Accept As Solution if it solves your problem.

  • Source System Problem after system refresh in RSA1 trx

    Hi,
    We have R/3 4.7 Test source system created in our SCM 2007 Test System. The source system check was OK.
    The R3 Test system was refreshed with Production data few days back and now my source system is not working. When i perform Source System check it says:
    BI unknown in source system
    BI IDoc type ZSSB006 is not the same as source system IDoc type
    I performed following steps in R3 Test system after its system refresh:
    1. Created logcal system and created RFC.
    2. Created port in trx we21.
    3. Created partner profile in trx we20.
    4. For the outbound parameter RSSEND, I had to create idoc type that should be same as in my SCM system i.e. ZSSB006.
    5. Created idoc type using trx we30 as a copy of RSSEND and added entry in table EDIMSG. Now, i could also create outbound parameter RSSEND with idoc type ZSSB006.
    After performing the above steps i also replicated the datasources for the R3 Test source system, but its still showing above error.
    I also checked the RSBASIDOC table in SCM test system. It has correct entry for my source system. But there is no such entry in RSBASIDOC table in the R3 test system.
    Someone pls help me.
    Regards,
    Chintan

    Hi
           Need to restore the All Dalaload connection settings after refresh the system which either R/3 or SCM.
    RSA1 -> select the Source system -> Right click -> Restore , It'll ask the connecon paramters like RFC , method of activations. Then check the connection test of the Source system .
    Check the the note for further  info...
    Note 886102 - System Landscape Copy for SAP BW and NW BI
    Hope halp you...
    Regards,
    Sureshram

  • Time Machine Restore - User Profile and System on two drives

    Hello,
    I need some help and I think here's the best place to get it.  I need to do a restore from Time Machine to a new system.
    My old (2008) Mac Pro as "died" and after having the nice people at the Mac Store look at it, I realized that it would be cheaper to buy a used system than to repair mine.  My CPUs are dead (2000$ to get them replaced) and one of my Raid 0 drive is dead too.   
    Old system:
    2008 Mac Pro 2.8 ghz (with Raid Card)
    Drive 1:  OCZ  (SSD drive) ---> System
    Drive 2:  Raid 0 (wiht Apple Raid card) ---> User profile
    New system:
    2008 Mac Pro 3.2 ghz (NO raid card)
    Drive 1: OCZ (Same from previous)
    Drive 2: 500 Gb (which came with the new system)
    Now I have done the Time Machine already but it only brought me back to the same point.   I have renamed the Drive 2 in the "new" system to "Raid 0" as it was the name it had in the previous system and it allowed me to logging to the system but I do not have any of my data on it.
    How could I restore my User Profile to Drive 2 on the New system ?
    Hopefully this isn't too confusing.
    Thanks for all the help.
    Richard

    The "full restore" from Time Machine is only for OSX drives.
    For data-only drives, use the Time Machine browser (the "Star Wars" display).  See Time Machine - Frequently Asked Question #15.
    Depending on your setup, you may also want to review Transferring Home Folders not on a Startup volume.

  • Delta Setup/Link  Broke After System Refresh in Sandbox with Prod

    Hi All,
       We have done the System Refresh for Sandbox with Production in BW. After that, we tried to load 0FI_GL_4 Delta and it failed with 'Queue 0FI_GL_4 is not available in the Source System' in Monitor. It means something went wrong in System Refresh process and the Delta setup broke. The 'Status' traffic light for 0FI_GL_4 DataSource is in RED in 'BW Delta Queue Maintenance' (RSA7) in R/3 system. When I display this Status (Red traffic light) it says 'There are still no parameters available for the delta transfer'.
       Since the Delta link broke, I have deleted the 0VENDOR_ATTR Master Data DataSource in RSA7 in R/3 and Initialized the Delta in BW for this 0VENDOR_ATTR and it completed successfully and now 0VENDOR_ATTR Master Data DataSource in RSA7 in R/3 is in GREEN.
       But, we have GL InfoCube which has 120 million records and if we initialize the Delta it will take atleast 7-10 days. It will take atleast 2 weeks for all the InfoCubes and ODS's.
      How could we restore the Delta setup/link and the Status of the DataSources will turn into GREEN in RSA7 in R/3, PLEASE ?
    Thanks in advance.

    Hi,
    Ask your BASIS team to run BDLS. That should take care of the problem. It'll repoint the delta queues to the correct source system. With the refesh the delta DS will point to the system it was refreshed from, hence the problem.
    Cheers,
    Kedar

  • Windows 8.1 will not activate on HP19-2113w after system refresh.

    Everything was working fine on my PC.  Then the other day it crashed and said there was a disk error and that it had to scan the whole drive to find the error. It finished scanning, but windows 8.1 would not load sucessfully.  Therefore I did a system refresh thru HP recovery.  After doing that windows would start up normally, but I lost my activation.  When I tried to activate the response was "Key doesn't work try again later" or something like that.  Kept trying, no luck.  I thought it may have been an error with the system refresh, so I did the total system reset (after saving personal data).  Now I am having the same problem with activation, and If I try to navigate the normal way to the activation screen, the screen disapears.  I can get to activation using command prompt.   but key still does not work.  The key I am using I retrived from my BIOS data.  Also, I ran the refresh and reset from the origional hard drive partition.  I hope someone has a solution to this.  Thanks is advance Bill   

    Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your desktop computer will not activate after performing a system refresh, and I would be happy to assist you in this matter! In order to correct this issue, I suggest following the steps in this resource on Windows 8 product activation, which should help to activate Windows 8.1 on your system. Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards

Maybe you are looking for

  • Taking 1080i AVCHD and making a 720p video/project?

    So 1080i is a little bit overkill for me, especially since I dont actually own an HDTV or anything so i was just curious as what the workflow would be for going down to 720p? Can I just make a new 720p sequence and drop the 1080i footage in there and

  • Can I hold a conference call on Face Time?

    Can I set up and hold a conference call on Face Time, using four different locations simultaneously?

  • Can anyone tell me why there's an extra space here?

    Can anyone tell me why there's an extra space here? http://www.libertywebmarketing.com/test/test.html SOURCE CODE: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="

  • What Is Wrong With My Program Help

    This Is The Assignment I Have To Do: Write a Java program that prints a table with a list of at least 5 students together with their grades earned (lab points, bonus points, and the total) in the format below. == Student Points == Name Lab Bonus Tota

  • LiveCycle Designer vs FormsCentral

    I had Adobe Acrobat Pro X which included LiveCycle Designer.  I used this to create a couple of forms which I now need to make changes to.  My firm has upgraded us to Adobe Acrobat XI which does not include LiveCycle but does have FormsCentral.  Can