CUCM and H323 gateway-Cause i = 0x80A6 - Network out of order

Hi,
I cant get calls into the CUCM from a H323 gateway. Incoming external calls here out of service message or Number Unobtainable. I've attched logs if anyone can help?
Rich

Hi Alex,
Thanks for reply. I should've attached the full config as it shows the Translation Rules. See below.
Can anyone help?
voice translation-rule 2
rule 1 /^56/ /5\2/
rule 2 /^6/ /5/
rule 3 /2/ /52/
voice translation-rule 3
rule 1 /^1$.........$$/ /01\1/
rule 2 /^2$.........$$/ /02\1/
rule 3 /^7$.........$$/ /07\1/
rule 4 /^8$.........$$/ /08\1/
rule 5 /^4$......$$/ /01914\1/
rule 6 /^2$......$$/ /01912\1/
voice translation-rule 6
rule 1 /^[1-9]/ /90\0/ type international international
voice translation-rule 7
rule 1 /^1/ /901/
rule 2 /^2/ /902/
rule 3 /^3/ /903/
rule 4 /^4/ /904/
rule 5 /^5/ /905/
rule 6 /^6/ /906/
rule 7 /^7/ /907/
rule 8 /^8/ /908/
rule 9 /^9/ /909/
voice translation-profile INCOMING
translate calling 7
translate called 2
voice translation-profile OUTGOING
translate called 3
voice-card 0
dsp services dspfarm
interface FastEthernet0/0
ip address 192.168.178.66 255.255.255.192
ip pim dense-mode
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 192.168.178.66
interface FastEthernet0/1
no ip address
duplex auto
speed auto
no keepalive
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
control-plane
voice-port 0/1/0
translation-profile incoming INCOMING
compand-type a-law
cptone GB
description ISDN2 .......... lines 1+2
voice-port 0/1/1
translation-profile incoming INCOMING
compand-type a-law
cptone GB
description ISDN2 .......... lines 3+4
ccm-manager music-on-hold
mgcp fax t38 ecm
dial-peer cor custom
dial-peer voice 999 pots
destination-pattern 999
port 0/1/0
forward-digits all
dial-peer voice 9991 pots
destination-pattern 999
port 0/1/1
forward-digits all
dial-peer voice 112 pots
destination-pattern 9112
port 0/1/0
forward-digits 3
dial-peer voice 1121 pots
destination-pattern 9112
port 0/1/1
forward-digits 3
dial-peer voice 9999 pots
destination-pattern 9999
port 0/1/0
forward-digits 3
dial-peer voice 99991 pots
destination-pattern 9999
port 0/1/1
forward-digits 3
dial-peer voice 100 voip
preference 2
destination-pattern 52...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.0.150
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 101 voip
preference 1
destination-pattern 52...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.203.20
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 1 pots
translation-profile outgoing OUTGOING
preference 3
destination-pattern 0T
translate-outgoing called 10
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/0
forward-digits all
dial-peer voice 11 pots
translation-profile outgoing OUTGOING
preference 4
destination-pattern 0T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 9 pots
translation-profile outgoing OUTGOING
preference 1
destination-pattern 9T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/0
forward-digits all
dial-peer voice 91 pots
translation-profile outgoing OUTGOING
preference 2
destination-pattern 9T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 2 pots
translation-profile outgoing OUTGOING
destination-pattern 2......
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 21 pots
translation-profile outgoing OUTGOING
destination-pattern 2......
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 52982 voip
preference 1
destination-pattern 562982
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.0.150
dtmf-relay h245-alphanumeric
no vad

Similar Messages

Cause 1 = 0x82A6 Network out of order - ISDN error

When we are try to make outgoing call, we are getting the below error :
cause 1 = 0x82A6 Network out of order
Incoming call there is no problem in the Same E1 PRI line, ISP saying there is no problem from thier side.

We are using h323 gateway. When I am using csim start the outgoing calls fails
ISA-VG1#un all
All possible debugging has been turned off
ISA-VG1#csim start 93XXX6306
csim: called number = 93XXX6306, loop count = 1 ping count = 0
csim err csimDisconnected recvd DISC cid(570049)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0
Router#sh gateway
H.323 ITU-T Version: 4.0   H323 Stack Version: 0.1
H.323 service is up
This gateway is not registered to any gatekeeper
Alias list (CLI configured) is empty
Alias list (last RCF) is empty
ISA-VG1#csim start 93XXX6306
csim: called number = 934466306, loop count = 1 ping count = 0
*Feb 5 13:06:47.949 UTC: ISDN Se0/3/0:15 Q931: Sending SETUP callref = 0x3957
callID = 0xCE73 switch = primary-net5 interface = User
*Feb 5 13:06:47.953 UTC: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x
3957
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
        Called Party Number i = 0x80, '34XXX6306'
                Plan:Unknown, Type:Unknown
*Feb 5 13:06:48.049 UTC: ISDN Se0/3/0:15 Q931: RX <- SETUP_ACK pd = 8 callref
= 0xB957
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
csim err csimDisconnected recvd DISC cid(570048)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0
ISA-VG1#
*Feb 5 13:06:48.049 UTC: ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8 callref
= 0xB957
        Progress Ind i = 0x8288 - In-band info or appropriate now available
*Feb 5 13:06:48.097 UTC: ISDN Se0/3/0:15 Q931: RX <- RELEASE pd = 8 callref =
0xB957
       Cause i = 0x82A6 - Network out of order
*Feb 5 13:06:48.097 UTC: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callr
ef = 0x3957
Incoming calls are perefect, Please let me know the problem is from ISP Side ?

"Network out of order" and "Short message transfer rejected"

Guys,
I have a BB 9300 3G Curve and I have trouble sending SMS. This is a peculiar problem since I
#1 am able to send an SMS problem free sometime
#2 get an error message saying "Network out of order"
#3 get an error message saying "Short message transfer rejected"
Plus, this problem is not specific to a particular contact number. I get different messages (1,2,3 above) for the same number at different times. I have tried putting my SIM in a different handset and it works perfectly fine.
Someone please HELP!

Simply try pulling out the battery and leaving it out for a couple minutes. Usually, that is the fix-all to glitches. If not, you should contact your wireless mobile provider and see if they can help you. Usually, they are very easy to get along with and want to help you. But I think the battery pulling out will help you. It's happened to me before and I had to do that.

I have an iMac mid 2010. After Disk utilities said the drive was corrupt, I ran the hardware test (extended) 3 times. No problems. I than ran Disk utility again and got 2 messages in red-keys out of order, and --Volume corrupt, can't be repaired. I tried

I have an iMac mid 2010. After Disk utilities said the drive was corrupt, I ran the hardware test (extended) 3 times. No problems. I than ran Disk utility again and got 2 messages in red…keys out of order, and ……Volume corrupt, can't be repaired.
I tried to do a system install, but message said…disk can't be changed. Will a complete erase and install fix this ?
Everything is backed-up.

There's hardware and software.
Your drive could physically be in good condition but something has caused the file structure to be messed up (it just happens sometimes). The directory that keep track of files is corrupt. Disk Utility can help determine if that is the issue. In some cases it can repair the problem but it cannot do it to a drive that is being used to boot the system while you are doing that. You have to boot from another drive. Some things DU cannot repair and you need to try a stronger utility such as Diskwarrior.
A failing hard drive (one with mechanical issues) can be a cause of file structure issues but this is by no means always the case. Apart from looking at the SMART diagnosis feature of Disk Utility (and smart isn't totally reliable) there often isn't a way to tell if a drive is failing until it suddenly happens, which is why you need to maintain backups.
In your situation it does sound serious and not just minor directory corruption. You can try erasing (formatting) the drive, You may need to do this if it is really corrupt, in which case there could be underlying physical issues. I use old technology but if you have the patience you can try erasing the drive with the security option of writing zeros once (don't do more unless you are going on a 3 week vacation). This makes the drive not simply assume everything is okay by forcing it try every part of the drive by writing data. If something is gong wrong you may find it marks a lot of bad sectors, or flat out refuses to format. Then you know you need a new drive.

Network out of order (38)

Hi have a 1760 router. I can make call but i can not receive calls and send me this error:
dur 00:00:00 tx:0/0 rx:0/0 26 (network out of order (38))
IP 0.0.0.0:0 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g729r8 pre-ietf
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
240B : 2007 1001116340ms.2006 +-1 +130 pid:96300 Originate 6301
dur 00:00:00 tx:0/0 rx:0/0 26 (network out of order (38))
IP 0.0.0.0:0 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g729r

Who is calling you, using what protocol, and what the router is supposed to with the call ?

Sms network out of order for one contact

I have had my curve for a while and i cannnot seem to send an sms to one of my contacts only as oit comes up with the network out of order error message! Help Please

Step 1: Remove your battery while your phone is powered on then replace it a few seconds later.
Step 2: Try once again to send that contact an SMS.
Step 3: Thank me for the helpful advice and have a good life with your new-found happiness.
(After that, I really hope my suggestion works!)
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

Phone keeps on telling me network out of order

Help! Everytime I try to send sms on my z10 it keeps on telling me network out of order. This is the first time that it has happened to me and it's really bothering me. How can I fix this?

That seems strange. Try registering your phone on the network once again.
To do this, swipe down from the top of your homescreen and select Settings>About and switch the Category menu to Network. Next, press the three dots in the bottom right corner and register your phone again.
Try that and post back with your results.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

SMS: Network out of order

I got my blackberry curve 8520 on friday, o2 contract, registered it all, sorted and working, then on sat swapped my pay and go number to my contract number so i wouldn't have to tell everyone. they said it would take 24 hours to swap so i wouldn't be able to text which i was fine about.
Its now been more then 24 hours and whenever i try to send an SMS i shows a X and says "Network out of order". I can email, blackberry messenger, call, facebook send and recieve etc. only thing i cant do is send a SMS??
Pulled battery out and SIM. But will not work.
Anyone got any ideas?
Thanks

Get your sms service number from your service provider, google it.
1. Go to options
2. go to sms
3. service center and change the number to the right service number.
Hopefully this will work for you.

-shift-and-spacebar-functions-of-a-keyboard-are-out-of-order

i-have-a-HP HDX16t Premium Series Notebook PC.the-shift-and-spacebar-functions-of-a-keyboard-are-out-of-order.they-are-not-jamed,i-can-push-them,but-there-is-no-spacing-between-words,and-shiftbar-does-not-perfom-its-function-please-help-to-correct-the-problem-i-am-taking-classes-online-have-to-wright-research-papers-thank-you-in-advance-galyna

galyna wrote:
i-have-a-HP HDX16t Premium Series Notebook PC.the-shift-and-spacebar-functions-of-a-keyboard-are-out-of-order.they-are-not-jamed,i-can-push-them,but-there-is-no-spacing-between-words,and-shiftbar-does-not-perfom-its-function-please-help-to-correct-the-problem-i-am-taking-classes-online-have-to-wright-research-papers-thank-you-in-advance-galyna
If I understand correctly, you are saying that neither of the shift keys work and that the spacebar does not do anything? Which operating system is installed and  what keyboard is installed? (see image) Click on it and you will see which keyboard is installed. Do you have a multilingual user profie setup? That is the reason my keyboard shows in the taskbar.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

B10 build TableView row selection causes columns to stretch out of order

When running the following css on a tableRow to change the selected highlight colour. If you have 50 of more rows and need to use the arrow keys to scroll the columns become stretched and out of order
.table-view .indexed-cell .cell: selected {
-fx-border-color: #f8c27f;
-fx-background-color: rgb(230,230,230);
}

Could you please post a bug in the JavaFX Jira at http://javafx-jira.kenai.com. If you file it under the 'runtime' section against the 'controls' component, it will be looked at as soon as possible. Ideally you'd include a small test application as an attachment.
Thanks!
-- Jonathan

NETWORK OUT OF ORDER

according to this http://btsc.webapps.blackberry.com/btsc/dynamickc.do?externalId=KB13324&sliceID=1&command=show&forwa...
i should change the Network Send over.. but it doesnt say GPRS..
my phone only have options:
..circuit switched
..circuit switched preferred
..packet switched preferred
..packet switched
please help.thankss!!

this solution has worked for me:
go into text messages (click menu button) click options, change "send text-only message as:" from "Always SMS" to "Always MMS". then try to text a contact, it has worked for me

My blackberry curve 8530 keeps saying the network is out of order?

I was at camp all week and had it turned off and when I got home and turned it on I tried textiing my friend and call my parents but it kkept saying that my network was out of order? I dont quite understand and I've taken the battery out and everything I'm not sure what to do and I really need my phone. Help?

Hi brittany097,
Welcome to the Support Community!
The following KB article should provide more information on the error message you receiving. "Network out of order error message received when sending an SMS message" http://bbry.lv/GGTq5j
Hope this helps.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

Why we dont' see H323 gateway and SIP trunk "registered" in CCM?

in CCM admin, we see the status of H323 gateways and SIP trunks have no "registered to xxxx" status.

Unlike devices with other protocols, there is no registration mechanism for these.

I hv a macbook and hv not been able to figure out whr to enter d gateway pathway in the network settings so as to get my internet started on my machine.. help me..

i hv a macbook and hv not been able to figure out whr to enter d gateway pathway in the network settings so as to get my internet started on my machine.. help me..

If you go to System Preferences (under the Apple menu) and select the Network pane, then select the interface you want to use (probably Wi-Fi or AirPort if you are wireless, or Ethernet if not.) If using a static IP address you can set your router address here. If you are using DHCP, it is not needed, since the computer will pick it up automatically.
Best of luck.

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except join not extend and I can not get a network on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Rout/

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
Airport gets it address DHCP.

Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
Note that the Express will not provide any additional wireless coverage when it "Joins".

CUCM and H323 gateway-Cause i = 0x80A6 - Network out of order

Similar Messages

Maybe you are looking for