DAQ Assistant Connection Diagram has different pinnouts than on the SCC-68

When looking at the Connection Diagram on LabVIEW 8.2.1 (from DAQ Assistant) The diagram shows pins 34, 66, 31, and 63 ABOVE pins 68, 33, 65 & 30. However, when looking at the physical layout on the SCC-68, these pins are transposed. That is to say that pins 68, 33, 65 & 30 are ABOVE 34, 66, 31, and 63 respectively.
Is this an error? If not, what is the logic behind this?

Hi RVallieu,
I think the disprepancies in the connection diagram that you are seeing are related to the type of connection you want to do. For instance, if you are doing differential measurements (good for rejecting Common Mode Noise Voltage), you would connect the positive lead to ai4 (pin 28) and the negative to ai12 (pin 61). On the other hand, if you are doing Single-Ended Ground Referenced (RSE) using channel 4, you would connect the positive lead to ai4 (pin 28) and the negative to ai gnd (pin 64). Whichever of these measurements that you choose, make sure that you configure the measurement type in MAX when you set up your task or in the VIs in LabVIEW under terminal configuration. Here is a link to a document that describes the differences in these measurement types. Table 1 breaks the information down into Signal Type and Input Configuration.
I opened up both the Device Pinouts in MAX for the 6221 and the manual for the SCC-68 (page 39) and compared the pins and they seem to correlate. Since the SCC-68 works with multiple M and E series DAQ devices, they should be the same.
As far as your measurement value is concerned, Ben has a good point that you may not have configured the accessory correctly in MAX. To do this, right click on your 6221 device and go to properties. Then in the accessory tab, you can select the SCC-68. This knowlegdebase describes the differences between SCB-68 and SCC-68 in case you were wondering. Hopefully this information will help!
Regards,
Vanessa L.
Applications Engineer
National Instruments

Similar Messages

Computer has different name than Itunes for Ipod Touch

I have an Ipod Touch 4th Generation 32gb. I have had no problems with it or with Itunes. My Mom came last Saturday to visit and she needed to charge her Ipod Touch so I hooked it to my computer where I always have a cord and charged it for about 45 minutes or so. I have no problem with my Ipod or with Itunes BUT when I go look at the device now on my computer,when it is connected to USB cord, it show "Marys Ipod" now instead of "Steves Ipod". In Itunes, it is still "Steves Ipod" and I can sync and all but I really want to get rid of "Marys Ipod" off my computer even though when I open it up, it is my ipod, just mislabed. I know because it has my pictures and her's is only 8gb. My Ipad2, is fine when I hook it up to the USB cord, It says "Steves Ipad" but when I hook my USB cord to my ipod touch, it still reads "Marys Ipod". Is this something I should be concerned about or is it not worth the hassle of trying to restore, etc? I have tried to change the name, but Windows won't allow. I do have Windows 7. I have also got the new update on Itunes and the new software(5.0) version.
I am stumped. I have googled this and have searched for over 3 hours today on how to fix this. Ready to bang my head against the wall. I have did a reboot on Ipod, I have restarted the computer. I have not reinstalled anything including Itunes.
Does anyone have any suggestions on what I can do? I would sure appreciate the help. Thanks in advance.

shellymoe
Currently Being Moderated Re: Computer has different name than Itunes for Ipod Touch
Jul 22, 2012 12:23 PM (in response to Toploader21120)
I just found the answer to this after hours of searching online. Make sure your iPod is hooked up to your computer & turned on.
Click on "Start" and in the search box type "regedit". This will display a program called "Registry Editor". Open it.
Click on the "Edit" tab and select "Find...". Type "Mary" in the search box and click "Find Next". It will bring up a list of everything that has "Mary" in it. (You may have to click on "Find next" under the "Edit" tab in order to find the associated items that have something to do with both "iPod" and "Mary".) What you need to pay attention to is not the NAME, but the DATA column. For me, the wrong iPod name was listed in 2 places in the data column. The actual names of those 2 items were "FriendlyName" and "Label".
Once you find the associated items that have to do with both the iPod and "Mary", right click on one of them. Select "Modify...". A box will open giving a "Value Name" box and a "Value Data" box. The "Value Data" box should say "Mary's iPod". All you have to do is change it to "Steve's iPod" and click "OK". Repeat the "Modify..." and renaming of the "Value Data" steps for every item that says something about "Mary's iPod".
Close the Registry Editor. Open "my computer" and see that it changed the name of your iPod back to "Steve's iPod".
Best Answer So far.....it really works...Thanks a million

Hi, when typing on my macbookair keyboard, i get a different text than on the keyboard - for exemple, typing "t", i get "t(". Any clue how to solve that? Thanks a loy

Hi, when typing on my macbookair keyboard, i get a different text than on the keyboard - for exemple, typing "t", i get "t(". Any clue how to solve that? Thanks a lot

Correct - another example, when i type "1" it writes "A1".
Hope this helps?

Ever since moving to OS 10.9.x my MacBook Pro has operated slower than before the change. Today I accessed the "monitor" and there scrolling up on the screen was this: "2/18/14 6:38:56.524 PM Wormhole[267]: pathToFramework: /Users/jbrad723/Library/Wormhol

Ever since moving to OS 10.9.x my MacBook Pro has operated slower than before the change. Today I accessed the "monitor" and there scrolling up on the screen was this:
"2/18/14 6:38:56.524 PM Wormhole[267]: pathToFramework: /Users/jbrad723/Library/Wormhol
2/18/14 6:38:56.524 PM Wormhole[267]: pathToFramework: /Users/jbrad723/Library/Wormhole/Wormhole.app/Contents/Resources/GoBridgeDemon. app/Contents/Frameworks/OTiTransfer.framework
2/18/14 6:38:56.527 PM Wormhole[267]: updateState: 5
2/18/14 6:38:57.525 PM Wormhole[267]: pathToDemonBundle:/Users/jbrad723/Library/Wormhole/Wormhole.app/Contents/Resour ces/GoBridgeDemon.app
2/18/14 6:38:57.525 PM Wormhole[267]: pathToFramework: /Users/jbrad723/Library/Wormhole/Wormhole.app/Contents/Resources/GoBridgeDemon. app/Contents/Frameworks/OTiTransfer.framework"
What is this?

Looks like remote access software.
http://wormholeremote.com

I update my iTunes to update my ipad and my computer died during this and now my ipad won't connect it has an iTunes sigh on the screen

I update my iTunes to update my ipad and my computer died during this and now my ipad won't connect it has an iTunes sigh on the screen

Hello Macahoy18,
Thank you for using Apple Support Communities.
For more information, take a look at:
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Have a nice day,
Mario

DAQ Asst Connection Diagram & Error 50103

Hello LabVIEW Community,
I am currently trying to integrate two different VIs which both require an AIGND on my SCB-100.
The SCB-100 has two separate AIGNDs (pinouts 1 and 2), but in the two DAQ Asst VIs I am using, the connection diagram for both asks for pinout 2.
I think this is leading to a Error 50103 about reserved resources.
Is there any way to switch one of the DAQ Assts' AIGND to pinout 1?
Thank you all for your help.
Sincerely,
Sincerely,
Ethan A. Klein
SB Candidate in Chemistry & Physics
Massachusetts Institute of Technology
Class of 2015
Solved!
Go to Solution.

Thank you very much, Mr. Knutson.
I didn't do a thorough search. I assumed it had something to do with my two DAQ Assistants, and figured it was that they shared a pinout as the error said something about resources being reserved.
Sincerely,
Sincerely,
Ethan A. Klein
SB Candidate in Chemistry & Physics
Massachusetts Institute of Technology
Class of 2015

AR Invoice has different currency than that of Sales Order.

SR 3-3082378321, Release 11.0.2.
Customer is reporting 3 Invoices (autoinvoiced at 3 different times) are having USD currecny_code where their (internal) sales order are in JPY. All other internal orders and invoices are fine. This problem is not reproducible at will, but it has happened 3 times in the past 2 months.
Need help on debugging the root cause of it. Support has done following:
1) reviewed Autoinvoice concurrent logfile and for the troubled invoice it shows:
=====
Customer_trx_id = 172207
Trx_currency_code = USD
trx_number = 6000042547
trx currency = :USD:
sys currency = :USD:
======
Where for a good one, it has:
=====
Customer_trx_id = 17220x
Trx_currency_code = JPY
trx_number = 600004254x
trx currency = :JPY:
sys currency = :USD:
======
This happened where system is selecting * from TAX_LINES_INVOICE_IMPORT_V. We understand data in TAX_LINES_INVOICE_IMPORT_V are fetched from ra_interface_lines_all table. This means data in ra_interface_lines_all table already has wrong currency_code.
2) We collected concurrent program logfile of the Receivables Interface Program , and it doesn't reveal anything relates to currency.
3) Customer stated there is no custom code for Receivables Interface program.
4) Customer is on 11.0.2 and we ran shp11ord.sql (per note 117627.1), that doesn't reveal any currency information neither.
5) We collected output from inv_info_110.sql for a good and bad invoices, and we see difference as follows:
=====
TRX_NUMBER TRX_ID TYPE STATUS TRX_DATE SOB CUST_ID RATE_TYPE RATE_DATE RATE
6000041899 170695 NSO OP 2/18/2011 1 1026
Good record has following:
=====
TRX_NUMBER TRX_ID TYPE STATUS TRX_DATE SOB CUST_ID RATE_TYPE RATE_DATE RATE
6000038751 163874 NSO OP 9/25/2010 1 1026 User 9/25/2010 120
The difference are the Rate_Type, Rate_Date, and Rate. The bad invoice has null value for these fields whereas the good one have all of them populated. Again, both orders (on Order Entry side) have currency of JPY.
6) Customer also confirmed that no one has ever manually changed anything in ra_interface_lines_all table.
Any idea what else we can do to sort out a root cause of this issue? Any pointers will be greatly appreciated.
Thanks and best regards,
Mark

Thanks for your input. But my problem is that on a same day, they have most invoices are generated fine while only one invoice goes like this. Therefore I can't see this is relating to any user type, nor gl rates issue.
I am actually looking for some inside on how to debug it. I can't trace the Autoinvoice on Production instance as the problem doesn't happen at will, and it has been only happened few times in the past couple months.
thanks, mark.

How to ORDER BY Different column than in the group by clause.

Hello, I have this sql statement
SELECT COUNT([Tags]) AS CNT, [Tags]
FROM [Tags], [Images]
WHERE
([Images].[Tags] LIKE '%' + [Tags].[LongTag] + '%') AND
([Tags].AllowTagPost = 'True' )
GROUP BY [Images].[Tags]
HAVING COUNT([Tags]) > 30
ORDER BY [Tags].[LastTagPost] DESC
It returns the tags, the number of occurances sorted by count. However, I want to sort it by a column in the Tags table named LastTagPost (DATETIME) The idea is to get the tag that hasn't been used in the longest time and also has more occurances
than 30 in the image table. When I try to order by this column i get an error that i'm sure most of you are all to familer with.
Error:
Column "Tags.LastTagPost" is invalid in the ORDER BY clause because it is not contained in either an aggregate function or the GROUP BY clause.
Any help would be greatly appreciated.

Couldn't you just include the LastTagPost as a MIN?
DECLARE @tags TABLE (LastTagPost DATETIME, LongTag VARCHAR(100), allowTagPost CHAR(5))
DECLARE @images TABLE (tags VARCHAR(10))
SELECT COUNT(i.Tags) AS CNT, i.Tags, MIN(t.LastTagPost) AS lastTagPost
FROM @Tags t
INNER JOIN @Images i
ON i.Tags LIKE '%' + t.LongTag + '%'
WHERE t.AllowTagPost = 'True'
GROUP BY i.Tags
HAVING COUNT(i.Tags) > 30
ORDER BY LastTagPost DESC
Don't forget to mark helpful posts, and answers. It helps others to find relevant posts to the same question.

Ipad 4 has different speaker than ipad 2?

I had an ipad 2 before and the ipad 4 sound much much better ... So, it s diffrent speaker inside?

Yep it does. Sound seems better than both iPad 2 and 3.

IPod has different dates than iCal

I have a problem with how my 4th Gen iPod and Nano sync with iCal. Some - not all - of the appointments get moved around. I have a series of recurring appointments on Thursday in iCal that show up on Wednesday on both iPods. I have synce'ed the iPods several times but the problem still persists. Also, I noticed that "All Day" appointments in iCal show up as 3PM appointments on my iPod. What do I need to do to fix this? I can't trust my iPod as a calendar app if it gets the appointments wrong!

I have a similar problem with my iPod/Calendar. There is a manual work around that worked for me. Seems to be a problem with iSync. Here is more details http://discussions.apple.com/thread.jspa?messageID=1747727&#1747727

My scanned document has different images than the original

Scanning a document as PDF. Some of the letters on the original do not appear on the scanned version

What options do you use?

Items in the shopping cart appear with different price than in the catalog

Hi All,
We are running SRM 5.0 (Classic Scenario) with external catalogues.
After selecting items from the external catalogue and transferring them to the shopping cart, the items appear with different price(the problem exists in the productive system)
The strange thing is that there is no dependence or sequence between the differences. For example, in one shopping cart, one item is with correct price, the price of the other item is not correct (when I click on the icon which is showing item details in the catalogue, the price is different than the one in the shopping cart). Sometimes the difference is significant, sometimes not - if the item price in the catalogue is 22.34 EUR, in the shopping cart is 21.22EUR or if the item is 45.62EUR in the shopping cart is 45.60 EUR. There is no logic.
I tried to create a shopping cart in the support system, with the same items from this catalogue, and they are sent back in SRM with the correct prices.
I traced all OCI parameters, sent from the supplier catalogue, and everything is correct.
At the example given below the price in the shopping cart ordered in the productive system is 69.00CZK, and after that during the test the correct price of 73.870CZK has appeared.
NEW_ITEM-DESCRIPTION==Durable-KeyClip-keytag%2C+black
NEW_ITEM-MATNR==
NEW_ITEM-MATGROUP==
NEW_ITEM-QUANTITY==10
NEW_ITEM-UNIT==EA
NEW_ITEM-PRICE==73.870
NEW_ITEM-PRICEUNIT==1
NEW_ITEM-CURRENCY==CZK
NEW_ITEM-NEW_ITEM-LEADTIME==1
NEW_ITEM-VENDOR==
NEW_ITEM-VENDORMAT==0176%2F1957001
NEW_ITEM-MANUFACTCODE==
NEW_ITEM-MANUFACTMAT==
NEW_ITEM-CONTRACT==
NEW_ITEM-CONTRACT_ITEM==
NEW_ITEM-SERVICE==
NEW_ITEM-EXT_QUOTE_ID==
NEW_ITEM-EXT_QUOTE_ITEM==
NEW_ITEM-EXT_PRODUCT_ID==23109
NEW_ITEM-EXT_SCHEMA_TYPE==UNSPSC
NEW_ITEM-EXT_CATEGORY_ID==55121504
NEW_ITEM-LONGTEXT_1%3A132==Durable-KeyClip%0D%0Akeytag%2Cblack%0D%0A%0D%0A6pc
I checked the error log in SLG1 for BBP_OCI, and no error message exists. In my opinion the problem can be in supplier system, because otherwise all items will be with wrong price. And at the moment, there are shopping carts in which all items are with the correct price!
It is not something in the user profile, because in one shopping cart created by one user some items are correct, some of them not.
I also checked with the supplier, they said that they haven't change the price, recently.
Has somebody of you met this problem?
In the IMG-> Define External Web Services (Catalogs, Vendor Lists etc.) I have set all parameters for the standard call structure: the URL of the supplier, our company ID and password for their catalogue.
In the Detail view for the catalogue, the following parameters are set
u201CAdditional functions in the product catalogueu201D field:
-     Display product data again in the catalogue
-     Validate product data from SAP Enterprise Buyer
-     Find supply sources
u201CTechnical Settingsu201D field
- Use Error Log
Thanks,
Desi

That means that we are not maintaining material numbers in SRM, so there are no predefined price or info records for that materials in R/3 system, or in SRM.
In the set up of external catalogues, validation of the price is set. Which means that, if a new shopping cart is created from already existing one, and meanwhile, a change of the price is done by the supplier in the catalogue, the new item price will be adopted in the shopping cart.
No prices are maintained in the SRM system, everything is from the supplier catalogue.
Desi

How do I address songs to a different album than on the computer?

I've just bought the new Iphone 3G but have hardly used Itunes before, that's why I need some (perhaps for you beginners) help.
I've got plenty of albums and I do not want to have all songs on all albums in my phone. That's why I want to create a couple of new albums with my favourite songs from different artist and add to my other albums on the phone. My problem is that I do not want to change the info about what album the song belongs to on my computer, only on the Iphone.
For example: I want to create an album with "the best of Faith no more" and I want it to contain 2 songs ("Ashes to Ashes" from the album "Album of the year" and "Epic" from the album "The Real Thing"). I want the new album (in my Iphone) to appear like any other album when I go through the cover flow (with a specific image, here is my first problem due to two different images on the two songs). Moreover I still want the song "Ashes to Ashes" belong to the album "Album of the year" on my computer (and that it has the image shown from the same album), but not on my Iphone (here it's supposed to belong to "the best of faith no more" and have a suiting image for my new album).
The only solution I can come up with is to make different playlists, but then they will not be shown in cover flow will they!?
When I have synchronized the music I can not edit the songs on the Iphone... so it seems I have to do, what ever I have to do, on my computer before I synchronize... :-/ (on my girlfriends iPod you can edit your songs on the iPod after you've synched, but not on my iPhone it seems...)
How do I solve my problem?
Cheers!
/Niclas

Yes, but that is not what I want. I want them to appear with my "custom made" album in cover flow on my phone. But still I want them to belong to it's original album on my computer...
I just want to gather some songs from an artist and put it all to one album without changing the album information (on the songs that are still on my computer)where it comes from!
Perhaps that isn't posible!? it is posible with my girlfriends iPod so I thought it would be with my iPhone as well
/N

Can a HP B210 AIO printer be connected to 2 different wireless networks at the same time?

I live in a household that has 2 different wireless networks in it (both me and my roommate have our own networks) and we just bought a new B210 series AIO printer. The printer detects both of our networks but only will print from one network at a time. If I want to print from my network I have to manually go to the wireless network wizard on the printer and select my network and re-enter my password. Is there any way that I can set up the printer to acknowledge both networks without having to constantly switch back and forth?

HI,
Sorry to say that what you want to do is not possible,
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

Photosmart C510A has different IP Addresses for the Zeen Wi-Fi and another for the Printer Wi-Fi

I recently changed ISP's and when I input the new Wi-Fi address it connected to the Zeen but not the Printer Wi-Fi, how do I change to the correct IP Address
This question was solved.
View Solution.

ok...read some more on the forum. Finally fix the problem by doing a factory reset and installing again.All is fine again....wireless connected!

DAQ Assistant Connection Diagram has different pinnouts than on the SCC-68

Similar Messages

Maybe you are looking for