Does BPM's required for these scenarios

Hi everyone,
Would anyone send me the steps for File-RFC-File and Http-RFC-FIle scenarios.
I created an Remote enabled function module with fileid and destination as import parameters and filecontent as export parameter.
My scenario is when i send the fileid as request, i should get filecontent as response to a file in xml format.
Do i need to do these scenarios in BPM, or can we do without BPM also.
Regards,
Varun

Hi,
Refer
Send RFC to SAP XI u2013
Send RFC to SAP XI Asynchronous
Ref: that
RFC Scenario using BPM --Starter Kit
the configuration steps will be;
1. 1 Sender agreement - Sender File CC
2. 2 Receiver Agreements - Recv. RFC CC and Recv. File CC
3. 3 Receiver Determination - File o/b -> BPM, BPM -> R3 (RFC) and BPM -> File (I/b)
4. Corresponding Interf. Detr. for the above Recv. determinations
HTTP to RFC - A Starter Kit
HTTP to RFC - A Starter Kit
thanks
Swarup

Similar Messages

I have a G5 and bought and upgraded to osx 10.5. now i need to upgrade to 10.5.6 or higher, but when i download and try to install, i get message "this volume does not meet requirements for this update".

i am trying to sync an ipad to a power mac g5. i bought and upgraded to osx 10.5 and have tried to download and 10.5.6 or higher, but i keep getting same message: "you cannot install mac os x update on this volume. this volume does not meet requirements for this update". help!

Mac OS X 10.5.8 Combo Update
Java for Mac OS X 10.5 Update 5
To me, in all such updates, goes without saying maybe: backup, repair permissions, repair your drive (Disk Warrior does more reliable and thorough job, and it comes out to pennies if you don't wait until needed). Clone your system so you can restore or use the backup - just in case.
I'd even do a fresh format after your clone is done and do a full OS clean install and update, and then a quick import from Setup Assistant.
Mac computer with USB 2.0 port
Mac OS X v10.5.8 or later
iTunes 10.2 or later recommended
(free download from www.itunes.com/download)
iTunes Store account
Internet access
I'm going to assume there is something with the partitions on the drive, partition table most likely, though I know I've seen others with that error message - doesn't really point to cause, rarely does (make sure latest firmware update etc is sometimes included but again, we know that isn't why).

Advise required for the scenario logic

Hi Experts,
SCENARIO NAME: FILE(text format) to IDOC.
requirement.
ex. input is 10 line items if any of the line item fails that supposed to throw exception what ever success lines are there that should process with out any fail or idoc should generated.
there no multi mapping. only one structure.
thanks

Hey,
You need to use 1:N MultiMapping here. In PI, each message is a single unit of work, either the complete message fails or passes.
For your case, you need to generate an IDOC for each Line item. This way, if one message fails(read line Item), other messages (read line Items) won't be affected.
As far as alerts are concerned, you can simply configure alerts using ALRTCATDEF or CCMS. That will take care of sending e-mail in case of failure.
Below is the Blog to do Multimapping and generate Multiple receive structures from a single source structure. Please note that the Blog is old and you don't need to use BPM for it:
Illustration of Multi-Mapping and Message Split using BPM in SAP Exchange Infrastructure
Thanks
Aamir

BPM Design required 1:N scenario

Hi Frnds,
I am working on one scenario JMS to (IDOC,RFC,MAIL).
1) when i receive message from MQ first level i wl apply XSLT Maping then it gives one message it contains 3 sub messages.in this case i have to send mail (confirmation mail ).
1.1 I have to map XSLT Mapping out put to MBGMCR IDoc or DESADV IDOC or RFC based on conditions.
      If SAP PO not found(RFC LookUp to retrieve PO Value) i have to send RFC message to SAP
      If SAP PO found ,the value =12 then i have to send MBG MCR IDOC
        If SAP PO found value is 10 0r 11 I Have to send MBGMCR IDOC and DESADV IDOC to SAP.
final confirmation mail...
my receievrs 5 .. how to design Intergratipn process,i developed message mapping and Operation mapping,but i am not clear about IP.
many thanks,
raj

Hi prateek thanks for you replay,but i need some clarity,
I developed 5 Interface mapping,
1)to post message in to RFC
2)to post message in to IDOC(mbgmcr if po =12)
3)to post message in to IDOC(mbgmcr if po = 10 or 11)
4)to post message in to IDOC(desadv if po=10 or 11)
5)Mail(rfc response value si have to send as a mail)
first four interface mapping wil have first step is XSLP Mapping second level maping is Message mapping.
in message mapping i retrieved PO value(RFC LookUp) based one PO value i created target.
my design approch correct? or i need to chnage design..
many thanks,
Raj

What Permission Set Is Required For This Scenario?

Hello,
I currently have an environment where I have limited users to being able to create/delete databases that only they have created. I did this by creating a Login with Public access and granting them the CREATE ANY DATABASE permissions to their
login. This works great as the users can create a database and delete their database but not anyone else's. The issue I have is the following scenario:
Database A is backed up from Server 1 (a different server than the restore server) and the DB was created by User 1
Database A is restored to Server 2 by User 2 who has CREATE ANY DATABASE permission (successfully).
User 2 can see the restored database, but cannot access it: The database is not accessible error.
When I view the database I see that the DB Owner is listed as User 1.
I've been trying to figure out how to be able to allow the user to become the new owner so they can edit/delete the database, but still not affect other databases that they do not own.
I've played with various permission sets but they end up being able to delete other user databases which I'm trying to avoid. I also don't want to have to change the owner myself.
Is there a permission set that I can grant that will allow this scenario?

That's a valid statement, let me explain my scenario and perhaps there is a better way to construct what I'm after.
I have a QA server where different developers create databases. All the databases backed up on the QA server are stored in a shared folder. This shared folder is accessible on our DEV server. We have a different set of developers
who at times need to restore one of the QA backups on the DEV server for different testing reasons. The permission set applied was simply to prevent someone from accidently deleting someone else's database. Restoring someone else's database in
our environment is not a concern.
With this in mind, I was hoping there was an additional permission I could grant that would allow the user restoring the database to become the new owner. I don't want the burden of approving it as it will always be approved.
I clicked on the connect link, but it returns as invalid -
The system has encountered an
unexpected error. We apologize for the inconvenience. The issue will be
addressed as quickly as possible.

Details required for these terms

Hi All,
can any body explain these terms in detail.
Main Attributes on item master window
i. Primary
ii. Tracking => - primary
- primary & secondary
iii. Pricing => - same as above.
iv. secondary => Defaulting
any response will be highly appreciated.
Regards
Asad

I think you might wany another forum. This is about portal specific topics, and yours looks like it's ERP functional.

How does the bandwidth required for a voice call v...

I want to have Skype calls with participants in (4) different locations. Some locations have a strong, reliable internet connection. Other locations have less strong and/or less reliable internet connections.
From the Skype website, I see the bandwith needed/recommended for voice calls, but I can't figure whether the needed/recommended bandwith increases with the number of call participants.
Thanks in advance for guidance on what (if anything) I can do to improve efforts to help folks with poor broadband access stay connected!

Connect and sync. That will backup your iPhone settings, and sync your contacts, apps, etc. to your computer via iTunes. Before you hand your iPhone in for the exchange, select Settings > General > Reset > Erase All Contents and Settings - that initiates a secure wipe of the phone contents and cannot be stopped once you start it.
When you get your new phone, connect it and sync, choosing the option to restore from backup. That and the subsequent sync will transfer all of your old settings, contacts, music, apps, etc., to the new iPhone. The only thing that will not transfer are the Wi-Fi passwords and the voicemail password. Those must be set up again on the new phone (that's a security measure).

HT4929 I have 2nd generation I-pod which does not meet requirements for ICloud. However, I was told that after I moved to ICloud if I connected my iPod to my Mac via the USB connection that my calendar and contacts would sync, but this didn't happen.

I have a 2nd generation Ipod and just moved to Icloud. I had been told my an Apple tech that although my contacts and calendar would not sync automatically I could connect the Ipod to my Mac via the USB port and ITunes would sync the calendar. Now I find that this is not happening. I am not happy that I will have to enter/edit calendar and contact info on two devices. Is there something I can do to fix this problem? Thanks.

one more detail, after a restore, when I attempt to reload music to the ipod, if I try and move, say, 20 files, the transfer seems to work as it should but then stalls on the last file. Eventually, the status will change to "Updates Files on (my ipod)" a and suggests the iPod is syncing even though I have the auto sync feature turned off.
This process eventually works itself out, and seems to take longer relative to the number of files I attempt to transfer. Once done, howver, if I try and eject and dismount the iPod, iTunes stalls with the spinning pinwheel and I am warned that the iPod is syncing again with the spinning candy cane status bar. Eventually thisd works itself out and the iPod dismounts from iTunes and the desktop and eventually the iPod is free to disconnect.
Then if I try and play the music I just transfered, the iPod says there is no music loaded.
Ideas?

How does OOB breadcrumbs work for multisite environment

Hi
I am currently using CatalogNavHistory and CatalogNavHistoryCollector to display breadcrumbs in my catalog pages.
My doubt is with ATG10.1 we are using multisite environment for our project. So one category will be part of more than one site.
So how does OOB CatalogNavHistory and CatalogNavHistoryCollector handle the breadcrumbs for these scenario?
Thanks
Ajay

Dear KK,
IF You want to use the EURO currency as transaction currency and Your Local currency is Australian Dollar, the System correectly will take the Exchange rate EURX.
EURO is used for the old european currencies
EURX for all the other foreign currencies
EMU indicator that means European Monetary Union has to be flagged if the referency currency is EUR.
I hope this can help You.
Mauri

Environemnt required for Installing essbase??

Hi
I am Planning to Install essbase in my Organization on Linux servers and Can some one help me out with prerequisites required??
Installing essbase 9.3.1
How many servers do i need??
Do i need one seperatley for shared services and one seperately for essbase server??
What is the ram required for these servers and we have to build application that will have a size of 40gb in future
Do i need to have 16 processors for each of the server??
Since the previous organisation i worked for had made their application run on 4 thred and each thread has 4 cpu'c??
I Had an idea to get Servers each with 32gb of ram with 16 cpus each
Can any one suggest me are these requirements sufficient or What are the Components i need to install on each servers
Is this the correct way of setting hardware??
Thanks
Kumar

Hi Atul,
Can you send me any document which gives the general information about the Configuration details for installing Essbase software.....
In your earlier reply, you have mentioned have that increment in CPU and RAM size does not result in increasing perforrmance. In application optimization way, I agree this is not helpful. But if hardware configuration is good, system performance will be better right...Please clarify me I am wrong.
Regards,
Upendra...

Goods receipt not required for freight items

Hi Experts,
We are using freight charge as extra line item in purchase order. Now client want that there shouldn't be any goods reciept if it is "Freight" item. I am thinking to use different material group or item category. Please advise if it is possible that if user enter PO number in MIGO then freight item should not appear (Based on material group or item category).
Also we are using quantity variance in Invoices, is it possible system don't block freight items as goods receipt is not required for these.
Regards,
Kamal

Hi,
For not receiving the goods with respect to freight line item in PO,
1. First uncheck the Goods receipt indicator in PO delivery tab,.
2. also uhchek GR based invocie verification in Invocie tab,
3. As GR based invocie verisfication is not activated system will not block for quantity variance.
Regards,
Bharat.

Error while create TSW ticket processing for DES Scenario

Hi Experts ,
I am facing an error while doing TSW - ticketing process for DES scenario
For STO creation under movement type O - Origin T - Transfer.An error is coming while actualizing the ticket
Error states : " you do not have authority to access the shipment ( Return code 4)
Request all experts to look into the issue and kindly reply
Thanks in Advance

Hi,
Error states : " you do not have authority to access the shipment ( Return code 4)
It seems authorization problem,kindly take help of basis team for authorization
kapil

Bandwidth requirement for voice calls

Hi All,
Need expertise advise on the following concern about voice call.
1. Bandwidth requirement for video call across all other endpoint(using Polycom / Lifesize end point at their end)
a)Standard Video
b)1K HD Video
c)4K HD Video
2. Plus can we determine bandwidth required for all the following below:
a. 1 to 1 VC end point ( Cisco TP – Cisco TP)
b. Bridge call ( Cisco TP to Polycom / Lifesize)
c. 1 to 1 VC end point ( Cisco TP – Polycom / Lifesize)

Thanks for the info Wayne. I missed out information about the endpoint.
Client using CTS 3010. Acoording to datasheet it says
11.9 Mbps (1080p, 30 fps best motion handling), 10.1 Mbps (1080p, 30 fps better motion handling), 8.8 Mbps (1080p, 30 fps good motion handling)
6.4 Mbps (720p, 30 fps best motion handling), 4.5 Mbps (720p, 30 fps better motion handling), 3.1 Mbps (720p, 30 fps good motion handling)2
My question is does the bandwidth required for both ways or only one way?
And I'm aware CTS 3010 doesn't support 4K video.

ALE Configurations for IDOC2IDOC scenario

Hi Experts,
Can anyone list down wht r the ALE configurations are required for IDOC2IDOC scenario?
1. Sender SAP ---> XI
2. XI ---> Reciever SAP
Please provide me the TCodes with the details that are needed for the above scenario?
Your help is higly appreciated
Rgds
Faisal....
Edited by: Abdul Faisal on Jul 28, 2008 11:49 AM

Hey,
Steps for ALE settings:-
Steps for XI
Step 1)
     Goto SM59.
     Create new RFC destination of type 3(Abap connection).
     Give a suitable name and description.
     Give the Ip address of the R3 system.
     Give the system number.
     Give the gateway host name and gateway service (3300 + system number).
     Go to the logon security tab.
     Give the lang, client, username and password.
     Test connection and remote logon.
Step 2)
     Goto IDX1.
     Create a new port.
     Give the port name.
     Give the client number for the R3 system.
     Select the created Rfc Destination.
Step 3)
     Goto IDX2
     Create a new Meta data.
     Give the Idoc type.
     Select the created port.
Steps for R3.
Step 1)
     Goto SM59.
     Create new RFC destination of type 3(Abap connection).
     Give a suitable name and description.
     Give the Ip address of the XI system.
     Give the system number.
     Give the gateway host name and gateway service (3300 + system number).
     Go to the logon security tab.
     Give the lang, client, username and password.
     Test connection and remote logon.
Step 2)
     Goto WE21.
     Create a port under transactional RFC.(R3->XI)
     Designate the RFC destination created in prev step.
Step 3)
     Goto SALE.
     Basic settings->Logical Systems->Define logical system.
     Create two logical systems(one for XI and the other for R3)
     Basic settings->Logical Systems->Assign logical system.
     Assign the R3 logical system to respective client.
Step 4)
     Goto WE20.
     Partner type LS.
     Create partner profile.
     Give the outbound or inbound message type based on the direction.
                In your Sender R3:- outbound
                In your Receiver R3:- Inbound.
Step 5)
     Goto WE19
     Give the basic type and execute.
     fill in the required fields.
     Goto IDOC->edit control records.
     Give the following values.(Receiver port,partner no.,part type and sender Partner no. and type)
     Click outbound processing.
Step 6)
     Go to SM58
     if there are any messages then there is some error in execution.
     Goto WE02.
     Check the status of the IDOC.
     Goto WE47.
     TO decode the status code.
Step 7)
     Not mandatory.
     Goto BD64.
     Click on Create model view.
     Add message type.
BD87 to check the status of IDOC.
In case if not authorized then go to the target system and check in SU53, see for the missing object
and assign it to the user.
SAP r3
sm59(status check)(no message)
WE02(status check)
WE05(status check)
BD87(status check)
WE42 process code
WE47 status info.
<removed by moderator>
regards,
       Milan
Edited by: Mike Pokraka on Jul 28, 2008 5:04 PM

Minimum parameters and values required for 11g database

Hi
Can anyone please provide me with the list of parameters and the minimum value required for these parameters in 11g database (11.1.0.6.0).
Thanks

user8940828 wrote:
Thanks for your help
But this basic parameters did not mention the following parmeters . What can be the mimimum value that can be assigned to these parameters.
dml_locks
log_checkpoint_interval
log_checkpoint_timeout
open_cursors
open_links
parallel_max_servers
processes
session_cached_cursors
session_max_open_files
job_queue_processes
log_buffer
shared_pool_size
sort_area_retained_size
sort_area_size
db_cache_size
pga_aggregate_target
ThanksI suggest you to start letting the default parameters and then tune them step-by-step.
Eg:
- open_links => If you dont have database links you can avoid to set it.
- processes: number of backgroud processes + expected session/users for your application. if you have 1000 users connecting at the same time you would set a value higher than 1000.
- shared_pool_size, db_cache_size, sort_area_size, pga_aggregate_target are not mandatory if you use automatic memory management by Oracle.
- etc.

Does BPM's required for these scenarios

Similar Messages

Maybe you are looking for