Don't want to beat a dead horse, but...

This is the "I can't get ARD to Observe or Control a computer, though I can see it's there, what application is running, and I can also send it messages." thing again.
I have seen thread's on this before, and it seems like a semi-common problem.
I have tried some new things and felt it would be good to at least document what I have tried and learned from it to see if I can bring some new light on the subject.
I have 9 computers varying from G4's through G5's and a Imac all running OSX(tiger) 10.4.11. I am using ARD 3.2 and all of the computers are running ARD client 3.2.1. We are also all on the same network and all have Apple Remote Desktop enabled with full privileges. All of these computers are accessible with Observe and Control accept 1 of the G5's. So here are some things I have tried on my 1 renegade Mac.
First I thought it was a port problem cause some of the other macs were having problems with VNC server being on the 5900 port, after I changed the VNC server to 5902 I was able to get those running fine. So in the terminal I ran a command I learned from the Tiger Discussion Board (thanks Camelot).
# sudo lsof -i -P
This told me what ports are running and what is using them, the ones I am interested in are running on 5900 and 3283. On a computer that is working properly I find that port 5900 is being used by AppleVNCS and in some cases OSXvnc-se, and port 3283 is being used by ARDagent. Now on the mac in question I didn't see 3283 being used at all, so i figured my problem lied in getting ARDagent running. After talking to Apple Tech Support over the phone I was given a few ideas
1. Disable Apple Remote Desktop in System Preferences, and then re-enabled it.
2. Try logging on as a different user.
After realizing that I knew a little more about computers then the average Grandma (sorry grams) they were willing to give me a Terminal commands to try and provoke the service to run. As long as I understood that apple nether supports or condones the use of Terminal commands.
$ sudo /System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/Resources/k ickstart -activate -configure -access -on -restart -agent -privs -all
This effectively enabled port 3283 and ARDagent.
Alas in the end none of this worked, and the final solution seems to be having to reformat the G5. So I figured that instead of this being a big waste of time I would put this here in the hopes that this may help someone down the road.
Thanks for Reading.
Moderith

Glad you started this thread cos I was thinking along similar(ish) lines.
After reading all this psu stuff on here I dunno whether to pass my Thermaltake down the line to my wifes nforce2 setup and get something like a 480W Tagan TG480-U01. The Chieftec psu in her system only has 1 fan and I dont think that is helping her temps cos her Barton is running loads hotter (42C+) than my AMD 64 (30C). The thermaltake is probably just on the boundary in my setup. If it was wasnt for my wife's heat issue I would probably stick with my thermaltake for the Amd 64 system and run a second (cheapo 400w) psu above it using a relay switch that I got and then power all the fans and hdd coolers etc with that.
What ya reckon guys?

Similar Messages

  • Beating a dead horse but...Insufficient bandwidth error on Tiger 10.4.6

    So I'm running a new Macbook pro i just took out of the box, my girlfriend is doing the same. It's come with the latest version of Tiger. Here's the thing: with iChat my girlfriend and i get the all-to-familiar Insufficient Bandwidth message when we try to connect. I can connect with another friend on a standard Macbook, and my girlfriend can connect with me on the PC at my work, but we cannot connect with each other.
    We're both running off of Cable Modem router wifi and have bandwidth of at least 750 mbps. I've been through the support pages, opened port channels, adjusted quicktime streaming preferences, but to no avail. Any more ideas or any other tips to get this to work. Visual communication was the primary reason for the purchase of these computers, and we're frustrated to no end that it simply will not work after troubleshooting.
    Macbook Pro   Mac OS X (10.4.6)  

    HI theBen,
    Welcome to the Apple Discussions.
    At the ned of the day this can come down to the way your individual modems do NAT when using Port Forwarding, Port Triggering or DMZ and just not talk to each other properly.
    This is because there are about six different ways manufacturers use to achieve NAT.
    UPnP can help avoid this problem.
    See here for more info http://www.ralphjohnsuk.dsl.pipex.com/page15.html#CertainBuddy
    The iChat error messages are not always clear as to the exact problem and as you guessed ports can also be part of the problem.
    11:22 AM Monday; June 19, 2006

  • Processor Whine on the Newest MBPs (hate to beat a dead horse, but...)

    I was curious as to whether the infamous CPU whine (which I experience extensively on my Blackbook) still exists on the newest MBPs (i.e., Santa Rosa). My Blackbook has featured no less than three of the major known (or "unknown" if you are Apple) issues--the whine, the screwed-up trackpad, and persistent difficulties awaking from sleep--and I need to find another option. I suspect that the whine is still there on Santa Rosa MBPs, but I figure that it may be drastically reduced. I also hear that the trackpad is much better on MBPs than on Macbooks. Thanks.

    It is definitely the processor. I have had the exact same problem (as stated above) and I am sure that it is the processor (I know because I used a program to modulate the processor load with a slider and you could hear the noise change pitch until--finally--it went away). My hypothesis is that when the MagSafe adapter is plugged in, the computer switches over to a more high performance mode in which the computer uses more of the available resources, meaning that the processor has to do less work, and thus goes into an idle state more often. And yes, I think that frequency=intensity here. Another hypothesis might be that the adapter somehow amplifies the noise electromagnetically (this might make sense since the MagSafe both--obviously--conducts electricity and is secured by a magnet). At any rate, I didn't think that the noise was the processor at first, either, but as it turns out it is. And despite what others say, I think it's an Intel screw-up and not Apple, although Apple should take responsibility (more responsibility, that is). Indeed, I have had all sorts of problems with my Intel Macs, whereas I never, not once, had a problem my PPC Macs.

  • Beating a dead horse: Access Time Capsule files w/ an internet browser $

    I know I'm beating a dead horse here, but I have spent 2 days and countless hours looking up how to access my TC using an internet browser. I've read about port fwding and dynamic vs. static IPs. I cannot figure this out. If someone could help me and actually get it to work, I would be willing to pay them a reward for there services thru paypal. I don't want to sign up for Mobile Me or pay for any monthly subscriptions. I just wanna be able to access my TC and it's files where ever I am using an internet browser. Here's what I've got:
    MacBook 2GHz Intel Core 2 Duo
    Mac OS 10.6.4
    Verizon Fios router model MI424WR-GEN2 w/ a dynamic IP
    My TC is connected by ethernet to the Verizon router which enables me to use the WiFi on the TC
    Do I have to sign into my Verizon router and change setting?
    I'm pretty network illiterate so a good step-by-step would be great.
    Thank so much to whoever can help me.

    After all the setting have been put in, I'm getting an error that won't let me update the TC. It wants me to correct 2 problems. "The DHCP range you have entered conflicts with the WAN IP address of your Airport wireless device. What's that?
    This error message is due to the fact that the TC is performing as a router (its default) and not as a bridge (as it should be) because it is downstream of your Verizon-provided router.
    I apologize as I just realized when I first responded to you, that I had assumed that the TC was the only router in your network configuration. As such I had provided you with instructions based on that assumption.
    As such, at least two things need to change in the instructions that I provided: 1) The Verizon-supplied router is your main Internet router and it is the one that needs to be configured for Port Mapping/Forwarding, not the TC, and 2) The TC should be reconfigured as a bridge. (ref: AirPort Utility > Select the TC > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode)).
    So I used the "with Time Capsule password", was that right?
    Yes, that would be correct.
    Here are the "adjusted" instructions:
    AirPort Utility > Select the TC
    o Note the value of the IP Address. This is the IP address of the TC that was assigned by the Verizon-supplied router. We are going to want to change this to a static IP address. For now, just note what IP address range it is in, i.e., 10.n.n.n or 192.168.n.n, etc.
    Manual Setup > Internet > Internet Connection
    o Connection Sharing = Off (Bridge Mode)
    Manual Setup > Internet > TCP/IP
    o Configure IPv4 = Manually
    o IP Address = select an IP address just outside of the range provided by your Verizon router. For example, if the router is supplying IP addresses in the range of 192.168.0.2 - 192.168.0.50, enter 192.168.0.51 here.
    o Subnet Mask = 255.255.255.0
    o Router Address = This would be the LAN-side IP address of your Verizon router. Most likely it is 192.168.0.1
    o DNS Servers = you would need to get these from your ISP, or just use the OpenDNS servers
    o Domain Name = you can leave this blank
    Manual Setup > Disks > Files Sharing tab
    o Enable file sharing (checked)
    o Secure Shared Disks = With Time Capsule password
    o AirPort Disks Guest Access = Not allowed
    o Share disks over Ethernet WAN port (checked)
    Manual Setup > AirPort > Base Station
    o Enter a Base Station Password and verify it in the Verify Password box.
    o When you have made all the changes, click Update.
    Port Mapping instructions would be specific for your Verizon router. If you don't already, you may need to download a copy of the User Guide for this router in order to configure Port Mapping properly. The key is that the IP address for the port mapping would now be the private static IP address that you assigned to the TC. The Public & Private ports would be the same.

  • G3 os 10.3.9- question- beating a dead horse

    i know i am beating a dead horse and this has probably been asked a million times.
    ibook g3- 500mhz os 10.3.9
    i have always had pc's and i got the first iphone when they first came out, and had every once since, loved those **** phones.(really loving the iphone 4)
    my question is this, i am looking for tips also
    i recently came across a ibook g3 from a trade i made off craigslist.
    the ibook looks great, almost new.
    but i noticed that it surfs the net pretty fast but when i go to certain sites like worldstar or youtube it either cancels the browser or the video looks choppy and wont play smooth.
    what web browser is best for my os and also what can i do to make the youtube videos work smoothly, i have a bunch of softwear on the ibook i want to delete if it is slowing down the computer, excell, word, entourage, ect.
    mostly looking to just use the laptop for music, photos and surfing the web(facebook), and watching youtube video's
    any tips or advise, remember i am new to the mac world(outside of iphones)''
    thank you to all who answer,
    p.s. i know i got a outdated and old laptop but i got a good deal on it, traded away 2 old verizon cell phones i had that where collecting dust

    Hi, Paul. Welcome to Apple Discussions.
    Gerald's linked User Tip applies mostly to people working in Mac OS X 10.4.
    Here is the applicable section for Mac OS X 10.3.9:
    For any video URL on YouTube, add &fmt=5 to the end of the URL, and this will force videos to run in quarter VGA mode (320x240). The video quality will be degraded, but you should maintain a stable frame rate that is uninterrupted and capable of streaming without the need to pause and wait for the entire video to load.
    Also, if you restart the iBook, and don't have any other applications running except for the browser you're using to watch the video. Firefox will probably be more successful than any other browser for watching YouTube. Also, as the User Tip hints, pausing the video while it's loading and waiting until it's fully loaded can help.
    If the RAM has not been maximized with a 512 MB module in the one user-accessible RAM slot, that can help speed things up, too.
    The iBook G3 500 MHz came out in 2001; YouTube didn't start up until 2005. So you may be able to understand from that information why the 500 MHz iBook has a hard time with YouTube videos.
    Good luck with it.

  • Gamma issue... beating a dead horse

    so so confused, about this gamma shift from After Effects to Final Cut. I rendered the same clip out 4 different times and each time it has different gamma. Here are my render settings:
    1. v210 Codec
    2. Quicktime Animation
    3. Apple FCP Uncompressed 8bit
    4. ProRez 422 HQ
    The first 3 I thought were uncompressed or "slightly" compressed. The v210 codec looked like crap. The best was Animation & FCP Uncompressed... but again they look different. This is complete madness. And it did not matter if I selected use Legacy. Out of all our gear only Final Cut is gamma crazy... Can someone explain to me why such a difference in these clips. I know I'm beating a dead horse here. Thanks for any helpful tips or pointers

    Mine is fluctuating. Mine worked without having the Match Legacy Gamma Adjustment on and then off then on. I did something which seemed to overwrite a setting and reset something. Not sure.
    Try this.
    In project settings, Turn on the Blend Colors Using 1.0 Gamma.
    Render something in the render que. My video suddenly got darker and the results were darker than normal.
    I went back, checked it off, re-rendered it, and it worked out perfectly.

  • I have imported three gmail accounts into mac's mail client.  can i do anything to distinguish between them?  e.g., can i have each one appear in the mail list in a different color?  I don't want to do it by sender, but by email account.

    i have imported three gmail accounts into mac's mail client.  can i do anything to distinguish between them?  e.g., can i have each one appear in the mail list in a different color?  I don't want to do it by sender, but by email account.

    Welcome to the Apple Community.
    Enter the details of her second account at system preferences> mail, contacts & calendars.

  • I am trying to change my email address for an Apple ID and it is saying that it is already in use. I then sign in with that Apple ID and it says that the account is not set up yet, I don't want to set up the account, but I do want to use the email address

    I am trying to change my email address for an Apple ID and it is saying that it is already in use. I then sign in with that Apple ID and it says that the account is not set up yet, I don't want to set up the account, but I do want to use the email address in my original Apple ID! HELP!

    Welcome to the Apple community.
    Once you have created a rescue address, you cannot delete it, nor can you change it to the same address as used by your ID. There are numerous providers you can get additional email addresses from, such as Hotmail, Yahoo, Google etc etc.

  • Urgent my site don't want to open on Internet Explorer but is ok on Safari

    Urgent my site don't want to open on Internet Explorer but is ok on Safari
    This is a site I made for my client http://www.ajanatransportation.com/ everything was ok until I instal the text effect on the top (It's an XML flash text)
    I didn't see it before tonight... My client didn't say anything but I'm sure is not very happy!
    Well can anybody tell me what do I need to do to fix that problem Please>>>>
    To me it's like a missing div or something like that...
    JP

    Hi JP,
    my IE 8 shows your website correctly in my oppinion (hope I understood your concern in the right way), please have a look here:
    First phase:
    Second phase:
    Third phase:
    By the way, your "automatic srolling news on the top" starting with "Welcome to Ajana Transportation" also works fine.
    Hans-G.
    P.S.
    If you would come closer to the rotate idea, we should use for the required time segments simply the same images and call them in a multiple manner in the list.

  • TS1702 When trying to delete apps that I don't want, I get them to shake but no 'x' appears; what do I do?

    When trying to delete apps that I don't want, I get them to shake but no 'x' appears; what do I do?

    These apps you wish to delete aren't ones that came included with the iPad, are they? Those cannot be deleted. If these are apps you installed, try restarting your iPad:
    http://support.apple.com/kb/HT1430
    and see if it will then let you delete those apps.
    Regards.

  • Sorry to be kicking a dead horse, but...

    I have read the posts on viewing todo lists through Mail, etc. I have also read the posts on using third-party applications.
    I am thoroughly unsatisfied with Apple's inability or unwillingness (or combination of the two) to allow iCal todo list items to sync directly in to iCal on the iPhone. This is iRidiculous. We pay several hundred dollars for the device, and then an annual fee for .me accounts, and a simple operation, which is central to one's ability to organize using Apple products, is simply impossible?
    Please do something. And by something I don't mean archiving discussions on this topic so that comments cannot be posted.

    This is a user to user help forum only.
    All threads here are archived automatically after 90 days from the first post date when there has been no activity. The threads and posts are still available with a search, but it accomplishes nothing to bring up some 90 day plus old thread which has had no activity for a long period of time. There is nothing preventing you or anyone else from starting a new thread here to kick a dead horse. Many here don't use the search function and post the same question that gets posted and answered on a regular basis over and over and over and over again.
    These discussions are primarily for technical support issues and questions which are answered by fellow users only, not for just whining/ranting/complaining. Apple does not provide direct support or answer any questions here.
    Not sure where the problem lies with syncing To Do's, but there must be an issue we are not privileged to. Syncing To Do's with iCal is one thing and probably more easily doable than with syncing To Do's or Tasks with Outlook at the same time.
    You can use this link to provide Apple constructive feedback.
    http://www.apple.com/feedback/iphone.html

  • I don't want to download itunes 7.2 but I can't buy music!

    Everytime I go to buy a song it takes me to a page that says I should download iTunes 7.2 for free and install iTunes Plus but I don't want to! Can I not download any song without having downloaded iTunes 7.2 or something?
    I have dial-up, so downloading 7.2 who crash my computer and it seems sometimes when I download stuff to my computer it deletes it later.
    Will I have to download iTunes 7.2 to download songs now? Or is there something I can click to keep downloading songs with an older version of iTunes?

    Looks like we have the same problem - see if anyone comes up with the answer on my question posted yesterday "Do I have to upgrade from itunes 5 to itunes 7.2"

  • I don't want to use Yahoo for searching, but Firefox makes me

    For some reason, whenever I use the search bar, Yahoo operates as the search engine. I don't want to use Yahoo. How to I get it to go away so Firefox uses Google instead?

    The Firefox "address bar" is known as the "Location bar". The article that describes your issue is [[Location bar search]] - it explains how to change the Internet Keyword search service in the [[Location bar search#w_internet-keyword-search|Internet Keyword search]] section, under
    [[Location bar search#w_changing-the-keyword-service|Changing the keyword service]]
    To change it to Google (the default service), enter '''about:config''' in the Location bar (address bar), find the preference <nowiki>keyword.URL</nowiki> and then right-click on it and select "Reset", as explained in the article.
    P.S. I'm wondering how it got switched to Yahoo in the first place .... maybe a Yahoo toolbar or other add-on you installed?

  • ReTranscoding...Beating a dead horse.

    Okay, so i've previously posted some issues with Encore CS4 wanting to transcode BluRay compliant Mpeg2 files...
    Here's some of the steps i've taken to ensure conformity.
    A) All transcoded BluRay Mpeg2 files were encoded in AME with the CORRECT and defaulted presets made within AME..No matter what, Encore wants a transcode...
    Fine...
    B) Open Encore, and allow a transcode that is accepted by Encore's presets. SAVE THE PRESET...
    C) Use the SAVED PRESET in AME to guarantee that it's a legitimate stream..Run the encode.
    D) Encore still requires transcode,  although it was an Encore saved preset!!!
    But regardless, no matter what i try, Encore insists on running the files through it's own encoder/stream analyzer...
    E) Okay, download Restream and Media info...There is no difference in Encore's and AME's encoded streams. They're identical.
    F) Use Encore's encoded streams to use in a new project...Even the compliant .m2v's want a transcode in a new project...
    But regardless, no matter what i try, Encore insists on running the files through it's own encoder/stream analyzer...
    I'm starting to come to the conclusion that something is missing, and Encore has a failsafe mechanism to need to read through the .m2v files...
    THIS IS ONLY ON HD MATERIAL, including h.264 encodes..
    This isn't an issue with SD material..
    Does anybody have any further insight??
    Thanks...

    But that was the point in CS4, the preset was wrong.  You select the preset, then change that element
    It's greyed out...No selection possible for MPEG2 Blu-ray..
    Yes, you're correct for the H.264 Blu-ray..You can decide the profile. Mine is defaulted to High..
    I don't see an .epr file.
    If you've custom made one, it should reside under
    C:\Users\*your name*\AppData\Roaming\Adobe\Adobe Encore\4.0\Presets
    or
    C:\Users\*your name*\AppData\Roaming\Adobe\Adobe Media Encoder\4.0\Presets
    The system presets reside under C:\Program files(x86)\Adobe\Adobe Encore CS4\Presets
    Do a *.epr search in the top corner of the search string, and they're surprisingly scattered all over the place...
    Here's a sample of AME and the options for MPEG2-BluRay options.

  • K9A2 Platinum BIOS - Beating a Dead Horse?

    I heard a rumor (posted on the AMD processor forums in one of my posts) that MSI has stopped adding to the K9A2 Platinum (V1 board) BIOS.  They will not be adding a selective disable to the TLB bug, they will not be adding a northbridge multiplier setting.  Any truth to this horrible rumor?  My support request with MSI to add a northbridge multiplier so I can actually get my memory speed up where it is rated was met with the likes of "we probably won't be doing that".  Is BIOS 1.3 going to be the last one?  I don't really WANT to go back to BIOS P.0E just so I can unlock the northbridge multiplier.  It has a bunch of other issues with memory.  This board is priced quite low considering... I wonder if they ended up losing money on it and decided to stop supporting the V1 board?

    Quote from: exidous on 29-February-08, 19:03:18
    I would probably consider not being able to turn the TLB errata fix off a problem. Going from the original BIOS (v1.0 I think) to 1.3 lowered my computers performance by about 10%ish. This includes FPS in games and all 3DMark scores.
    Now it could be something totally different causing the lowered performance as I do not know when MSI added the "fix". I never run virtualization programs so the fix does only harm in terms of performance.
    I did ask MSI about the posibility to disable TLB fix in BIOS and this what they answered:
    Quote
    Dear Sir/Madam,
    Thanks for contacting MSI Technical Support.
    We will make a specifal Customer BIOS version for you.In this BIOS you can Enable and Disable the TLB errata fix(Add this Option for you).Please wait some days.If we complete it and we will contact you ASAP.
    Best wishes
    MSI Technical Support Team
    And today they sent:
    Quote
    Please download the Customer BIOS version(A7376ACI.101 which add the item of TLB) from MSI User FTP.
    Here is the link:
    ftp://ftp.msi.com.tw/BIOS/7376/

Maybe you are looking for