Download DNL_CUST_CND Successful or not?

Hello,
I have been downloading the objects DNL_CUST_CND and DNL_CUST_CNDALL. In R3AM1 (Monitor Objects), both Objects have status GREEN. But when I look in SLG1 (Display Logs) I see a lot of items with Problem Class Medium and 3 items with Problem Class Important (message : "Determination of values for application was interrupted").
I assume I have to correct the errors in the SLG1 log, or can I just proceed?
Any suggestions about the "Determination of values for application was interrupted" error? I cannot find any information on it.
Thanks in advance,
Jeroen

Hi Jeroen,
Look for the errors in SLG1, Some times it gives error like Table /SAPCND/T685 has been posted in the database with errors     or converting FIELD_TIMESTAMP into table. For these general errors reffer to the oss note 314542.
If the error mentioned in SLG1 is not relevent for your conditions then you can move ahed.
<b>Reward points if it helps!!</b>
Best regards,
Vikash.

Similar Messages

  • Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

    Hello，everyone.
    I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
    I download .bit file to FPGA and succeed.
    When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
    and the process is about 68% it fails.
    The message below the IMapct is as belows:
    done.
    PROGRESS_END - End Operation.
    Elapsed time =      0 sec.
    // *** BATCH CMD : identifyMPM
    // *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
    '1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
    done.
    INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
    but the original bitstream file remains unchanged.
    UserID read from the bitstream file = 0xFFFFFFFF.
    INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
    INFO:iMPACT - Current time: 2014/3/13 8:48:14
    // *** BATCH CMD : Program -p 1
    PROGRESS_START - Starting Operation.
    Maximum TCK operating frequency for this device chain: 66000000.
    Validating chain...
    Boundary-scan chain validated successfully.
    INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C >  120.00C]
    1: Device Temperature: Current Reading:  230.52 C, Max. Reading:  230.52 C
    1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
    1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
    '1': Programming device...
     Match_cycle = NoWait.
    Match cycle: NoWait
     LCK_cycle = NoWait.
    LCK cycle: NoWait
    done.
    INFO:iMPACT:2219 - Status register values:
    INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
    INFO:iMPACT:579 - '1': Completed downloading bit file to device.
    INFO:iMPACT:188 - '1': Programming completed successfully.
     Match_cycle = NoWait.
    Match cycle: NoWait
     LCK_cycle = NoWait.
    LCK cycle: NoWait
    INFO:iMPACT - '1': Checking done pin....done.
    '1': Programmed successfully.
    PROGRESS_END - End Operation.
    Elapsed time =     23 sec.
    Selected part: XCF128X
    // *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
    // *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
    INFO:iMPACT - Current time: 2014/3/13 8:49:32
    // *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
    PROGRESS_START - Starting Operation.
    Maximum TCK operating frequency for this device chain: 66000000.
    Validating chain...
    Boundary-scan chain validated successfully.
    INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C >  120.00C]
    1: Device Temperature: Current Reading:  230.52 C, Max. Reading:  230.52 C
    1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
    1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
    '1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
    INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
    '1': Downloading core...
     Match_cycle = NoWait.
    Match cycle: NoWait
     LCK_cycle = NoWait.
    LCK cycle: NoWait
    done.
    INFO:iMPACT:2219 - Status register values:
    INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
    INFO:iMPACT:2492 - '1': Completed downloading core to device.
    Current cable speed is set to 6.000 Mhz.
    Cable speed is default to 3Mhz or lower for BPI operations.
    Current cable speed is set to 3.000 Mhz.
    Setting Flash Control Pins ...
    Setting Configuration Register ...
    Populating BPI common flash interface ...
    Common Flash Interface Information Query completed successfully.
    INFO:iMPACT - Common Flash Interface Information from Device:
    INFO:iMPACT - Verification string:  51 52 59
    INFO:iMPACT - Manufacturer ID:         49
    INFO:iMPACT - Vendor ID:              01
    INFO:iMPACT - Device Code:            18
    Setting Flash Control Pins ...
    Using x16 mode ...
    Setting Flash Control Pins ...
    Setting Configuration Register ...
    '1': Erasing device...
    '1': Start address = 0x00000000, End address = 0x008CE03B.
    done.
    '1': Erasure completed successfully.
    Setting Flash Control Pins ...
    Using x16 mode ...
    Setting Flash Control Pins ...
    Setting Configuration Register ...
    INFO:iMPACT - Using Word Programming.
    '1': Programming Flash.
    done.
    Setting Flash Control Pins ...
    '1': Flash Programming completed successfully.
    Using x16 mode ...
    Setting Flash Control Pins ...
    Setting Configuration Register ...
    '1': Reading device contents...
    done.
    '1': Verification completed.
    Setting Flash Control Pins ...
    Current cable speed is resumed to 6.000 Mhz.
    '1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
    `Elapsed time =    814 sec.
    and i find many people have met the same thing. But they are spartan  series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
    I have read the status Registers and find there is an over-temperature state 
    and in Impact i could not readback the registers. It is strange.
    I am anxious about this problem and have not solved it yet
    What reasons may it be?
    Hope for your answer, thank you

    Hi~I want to know if you solve the configuration problem for virtex-6?
    As I encounter the  same configuration problem, I want to consult  you with some question.
    Can I have your email?
    gszakacs wrote:
    I have measured the VCCINT and find it is 1.0V, not 2.997V;
    That is not at all surprising.  I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
    my Reference board is ML605
    That would have been nice to know at the beginning...
    It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide.  See table 1-27, table 1-33 and the note below it about switch S1.
    I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA.  Have you tried power-cycling to see if the FPGA boots from the flash?
    I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that).  That will not only show the bits of the configuration status register, but also describe what each bit means.  Among other things you can check the state of the FPGA's configuration logic and the Mode pins.
     

  • Configuration data download to FPGA was not successful.

    I have designed a board with the Spartan 6 LX9 TQFP144 Package.
    I am able to load a bitstream to the device with the digilent HS-2. However the fpga can not selfconfigure from
    the attached SPI Flash.
    Here is the console output from iMPACT:
    GUI --- Auto connect to cable...
    INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
    INFO:iMPACT - Digilent Plugin: found 1 device(s).
    INFO:iMPACT - Digilent Plugin: opening device: "JtagHs2", SN:210249983579
    INFO:iMPACT - Digilent Plugin: User Name: JtagHs2
    INFO:iMPACT - Digilent Plugin: Product Name: Digilent JTAG-HS2
    INFO:iMPACT - Digilent Plugin: Serial Number: 210249983579
    INFO:iMPACT - Digilent Plugin: Product ID: 30900152
    INFO:iMPACT - Digilent Plugin: Firmware Version: 0109
    INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
    INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 10000000 Hz
    Attempting to identify devices in the boundary-scan chain configuration...
    INFO:iMPACT - Current time: 27.07.2015 16:19:26
    PROGRESS_START - Starting Operation.
    Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 2
    INFO:iMPACT:1777 -
    Reading C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
    INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
    done.
    PROGRESS_END - End Operation.
    Elapsed time =      0 sec.
    Selected part: N25Q128
    Unprotect sectors: FALSE
    INFO:iMPACT - Current time: 27.07.2015 16:20:19
    PROGRESS_START - Starting Operation.
    Maximum TCK operating frequency for this device chain: 25000000.
    Validating chain...
    Boundary-scan chain validated successfully.
    '1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations.
    INFO:iMPACT - Downloading core file C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9_spi.cor.
    '1': Downloading core...
     LCK_cycle = NoWait.
    LCK cycle: NoWait
    done.
    '1': Reading status register contents...
    INFO:iMPACT:2219 - Status register values:
    INFO:iMPACT - 0011 1100 1110 1100
    INFO:iMPACT:2492 - '1': Completed downloading core to device.
    '1': IDCODE is '20ba18' (in hex).
    '1': ID Check passed.
     '1': IDCODE is '20ba18' (in hex).
    '1': ID Check passed.
     '1': Erasing Device.
    '1': Using Sector Erase.
    '1': Programming Flash.
    '1': Reading device contents...
    done.
    '1': Verification completed.
    '1':Programming in x4 mode.
    '1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
    INFO:iMPACT - '1': Flash was not programmed successfully.
    PROGRESS_END - End Operation.
    Elapsed time =     78 sec.
    If i read that correctly Data was written to the Flash but the fpga was not able to configure from that data.
    Done-pin is connected to 3.3V via a 470 Ohms Resisor.
    The Flash is a N25Q128A13ESE40G, Datasheet here: http://www.farnell.com/datasheets/1674445.pdf
    I can perform a readback, checksum and an erase.
    If i do a read device status this is the console output:
    INFO:iMPACT - Current time: 27.07.2015 16:36:27
    Maximum TCK operating frequency for this device chain: 25000000.
    Validating chain...
    Boundary-scan chain validated successfully.
    '1': IDCODE is '20ba18' (in hex).
    '1': ID Check passed.
     '1': IDCODE is '20ba18' (in hex).
    '1': ID Check passed.
     '1': IDCODE is '20ba18' (in hex).
    '1': ID Check passed.
     INFO:iMPACT - '1': Reloading FPGA configuration data stored in flash...
    INFO:iMPACT:182 - done.
    On the Flash side I have pulled s# and Hold up to 3.3V with 100k Resistors.
    Can someone help me to find the problem?

    So does the FPGA try to read the SPI flash when it boots ?
    out with scope, probe the clock and the data , see if you can see it streamig out when you boot.
    If so, then one other thing I see wrong a few times is data path of the SPI, single bit or 4 bits of data.
        you have to make certain the bit file was created in the same width as the fgpa is expecting,
          In ISE I think its in Impact where you make the SPI flash file and specify this .
     

  • V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

    Hello，everyone.
    I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
    The flash is JS28F512P30E. The iMpact version is 14.7. 
    FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
    M[2:0] is 010 in Master BPI.  Ican  program FPGA through JTAG. The FPGA_DONE pin 's  LED can always flash.
    The error is shown as below. the full  IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
    Using x16 mode ...
    Setting Flash Control Pins ...
    '1': Erasing device...
    '1': Start address = 0x00000000, End address = 0x004E4AFF.
    done.
    '1': Erasure completed successfully.
    Using x16 mode ...
    Setting Flash Control Pins ...
    INFO:iMPACT - Using Word Programming.
    '1': Programming Flash.
    done.
    '1': Flash Programming completed successfully.
    '1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
    PROGRESS_END - End Operation.
    Elapsed time =    692 sec.
    Hope everyone give more advices. Thank you.
     

    Thank you very much!
    I can read ack the mcs file, but the file is much bigger than the original mcs file.
    The flash datasheet is in the attachment.
    I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
    asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
    ps:  The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .
     

  • Why is my downloaded Lightroom CC (2015) does not start? The download is successful otherwise okay. The shortcut appears on the desktop etc. But the program does not start.

    Why is my downloaded Lightroom CC (2015) does not start? The download is successful otherwise okay. The shortcut appears on the desktop etc. But the program does not start.

    Thank you help ! [?]
    2015-04-29 19:58 GMT+02:00 kglad <[email protected]>:
        Why is my downloaded Lightroom CC (2015) does not start? The download
    is successful otherwise okay. The shortcut appears on the desktop etc. But
    the program does not start.  created by kglad
    <https://forums.adobe.com/people/kglad> in *Creative Cloud Download &
    Install* - View the full discussion
    <https://forums.adobe.com/message/7495290#7495290>

  • Adobe Flash states successful when downloaded, however it will NOT work and disappears?

    I've tried numerous time to install, uninstall and install again flash player from adobe. I go to watch a video and it still states I need to update to newest version even after doing so. I'll shut down my computer and when I turn on my computer it's gone. When I go under system preferences it's there and it shows it's sucessfully running, however, it's not. What am I doing wrong, what am I missing?

    What I'm trying to confirm is, you downloaded the Flash Player Installer, and you get a .dmg (disk image) file, on your Desktop (or wherever it was downloaded).  You double-clicked that downloaded .dmg file, to "mount" the disk image, to open a Finder window with the installer (called Install Adobe Flash Player).  You double-clicked that installer to RUN the installer app and install Flash Player.  So, just downloading the installer does not install Flash Player...  I'm trying to confirm you ran the installer after downloading it.

  • Message to download latest version w/not disappear

    i keep getting a message that i NEED a new version of Adobe Flash Player in order to play games [i.e. SongPop on Facebook] ... i ALREADY have the latest, however, i downloaded it anyway, and the MESSAGE is still there when i go to play a game ... i've downloaded it a few times and the MESSAGE remains and will NOT allow me to play any games ... i even DELETED the Adobe Flash Player and started ALL over again, to NO avail ... how do i get PAST this???  thanks for your help!  patidee

    please note: i just went into TOOLS and it said that I.E. wasNOT my browser, so i made it my DEFAULT fyi ... attached are screens shows indicated that the FLASH PLAYER was downloaded, but when i go to PLAY a game or use MUZY i get the message to UPGRADEFrom: [email protected]
    To: [email protected]
    Subject: RE: message to download latest version w/not disappear
    Date: Tue, 26 Mar 2013 10:15:53 -0400
    Operating System is Windows 7 - Browser is Internet Explorer ... when i went to the page you suggested the box was BLANK, indicating that Adobe Flash Player was NOT installed, however, when i got to my Program Files it is listed THERE ... i have a screen shot showing it was Installed SUCCESSfully ... i have a screen shot showing it is among the list of programs on my computer; i don't UNDERstand this at all; why won't it RECOGNIZE it???
    Date: Tue, 26 Mar 2013 05:12:39 -0700
    From: [email protected]
    To: [email protected]
    Subject: message to download latest version w/not disappear
        Re: message to download latest version w/not disappear
        created by Sunil_Bhaskaran in Installing Flash Player - View the full discussion
    Please let us know your operating system and browser.
    Go to the following page and let us know what version of Flash Player you see there. http://helpx.adobe.com/flash-player/kb/find-version-flash-player.html
    Thanks,
    Sunil
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5179631#5179631
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5179631#5179631
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5179631#5179631. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Installing Flash Player by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • Purchased TV Show from iTunes directly downloaded to iPhone 3G not playing

    Hey everyone,
    I've just run into a weird issue, I just purchased & downloaded an episode of a TV show over a Wi-Fi network directly onto my iPhone 3G running the latest firmware. The download completed successfully, but when I try to play the TV Show from the iPod menu the iPhone gives me 'This movie could not be played' error message, even though everything looks ok.
    I am currently on holiday in the United States (not sure if it's relevant but I have an Australian iTunes account) and do not have access to my computer to try and troubleshoot the problem properly.
    Any ideas as to why this could have happened or has anyone encountered a problem like this before? I'm a bit peeved because I paid for it and have no way of re-downloading.

    I curently have, and have had in the past, a simmilar problem, except that the file will begin to play (in this latest case the first 48 seconds). Then the image will freeze on a frame, the sound will stop, while the scrub bar will still count upward (says that 49 seconds have played, then 50 seconds, then 51, etc). If I try to fast forward, the frame goes black, with no sound. I can rewind to the beginning, and play the first 48 seconds all I like, but always ends on the same frame.
    As I said, this is not the first episode with this has happened. I've only ever tried downloading "Hero's". The first time it happened was a season 3 episode on a second generation iphone running the then current firmware. I am currently using an iphone 3GS with version 3.1.2 firmware.

  • When I download a document, I get a message saying download was successful, but a blank screen where the document should be. What am I doing wrong?

    When I download a document, I get a message saying download was successful, but a blank screen where the document should be. What am I doing wrong?
    I go to an internet company and try to download a document from it. A tab pops up saying the download was successful, but all I see is a blank screen with UI at the top. I don't understand where the download is going.

    Thanks so much for your reply fanboy20. 
    Yes, just made sure of that.  I do have the latest version of Flash player.  But I have just staggered upon the answer.  Chalk it up to being a newbi.  I was not putting my apple tv to sleep and it would not allow me to see
    you tube on my computer while it was still operating on my TV.  When I realized that, I put the apple tv to sleep and bingo, my computer runs you tube fine.   Thanks again for your response.

  • Attachments dont download from Gmail in Safari, They disappear,I even tried re-downloading Safari and that download disappeared, it is not in my downloads folder, I actually searched in finder for the file and it is nowhere on my computer.  Please help!

    Attachments dont download from Gmail in Safari, They disappear,I even tried re-downloading Safari and that download disappeared, it is not in my downloads folder, I actually searched in finder for the file and it is nowhere on my computer.  Please help!

    Oh my gosh I had the EXACT same problem, and for ages I couldn't figure out how to fix it until today. Here's what I did:
    First I went onto my computer, opened itunes, and un-installed tumblr, vine and kik. These were the apps I was having problems with (it said I had them on my phone but, like you, they didn't show).
    Then I went to the itunes store, searched for each one, and it said I could update them so I did (just FYI: for tumblr a window popped up saying "please click ok to confirm you are 17 years or older", so I did that also)
    When I went back to my phone and tried installing them again (still on my computer), it worked!
    I hope this helps, because it was incredibly frustrating. Good luck!

  • HT203167 I had to replace my harddrive on my IMAC and downloads from ITUNES do not show up. How do I restore my previous library?

    I had to replace my harddrive on my IMAC and downloads from ITUNES do not show up. How do I restore my previous library?

    It has always been very basic to always maintain a backup copy of your computer for this very occasion.  Use your backup copy to put everything back.
    If for some reason you have failed to maintain a backup copy, not good, then you can redownload some itunes purchases in some countries:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • I rented Argo in iTunes on my iPad, it downloaded, yet it does not show up in my library.

    I rented Argo in iTunes on my iPad, it downloaded, yet it does not show up in my library. I have the most updated version of iTunes on my laptop and Apple TV. I logged onto my computer (Windows) and tried renting it again, iTunes store told me 'you have already rented this movie'. Is there an issue with rentals today? Help!

    Roaminggnome - Thanks for your reply, you made my day! This is my first time renting a video, so I didn't realize you had to go into a different app to watch it. Enjoy the rest of your weekend

  • My hard drive went bad and I lost a lot of purchased items from the iTunes store. I want to re-download them but can not. They still show up on my purchased items. How do I solve this?

    My hard drive went bad and I lost a lot of purchased items from the iTunes store. I want to re-download them but can not. They still show up on my purchased items. How do I solve this?

    Update to iTunes 10.3.1
    After you have finished, you can re download your iTunes purchases without having to re purchase.
    iTunes 10.3.1
    " Download Previous Purchases. Download your past music purchases again at no additional cost. Your purchases are available in the iTunes Store on your Mac or in the iTunes app on your iPhone, iPad, or iPod touch. Previous purchases may be unavailable if they are no longer on the iTunes Store."
    "Available on iTunes in the U.S. and Canada only. Title availability is subject to change."
    From here.  http://www.apple.com/itunes/

  • I have purchased Wedding Style By Miracle Design - it is showing in the downloads but I can not get it into lightroom - I am using a mac and the instructions are for windows.

    I have purchased Wedding Style By Miracle Design - it is showing in the downloads but I can not get it into lightroom - I am using a mac and the instructions are for windows.

    Return, cancel, or exchange an Adobe order

  • Regarding iTunes U courses, would I be able to link to books/sites (like say an amazon hardback book or link to a kindle book they can purchase and download).  Considering that not all books are available on iBooks I'm hoping this is allowed.   Also the p

    Regarding iTunes U courses, would I be able to link to books/sites (like say an amazon hardback book or link to a kindle book they can purchase and download).  Considering that not all books are available on iBooks I'm hoping this is allowed.   Also the possibility on monetizing since amazon gives commission for linking.  
    This question is for both the uncredited (private) courses and the bigger accredited accounts.    I am a  developer trying to learn how to help my area schools and also have some ideas for my own courses.    Obviously keeping within the iTunes U app would be preferred in most cases (to the learning experience) since they can take notes and see them within the app itself.
    If the reply comes from a non-apple employee please let me know (or better yet, link to) where that is clarified.   I would hate to develop something just to later find out it is against the apple iTunes U agreement.

    Fair question
    And, to be even more fair, I have to tell you that I get that every single day. And it's getting worse (or better, depending on how you look at it).
    I always try to let people know it's a long way until you get to a confortable point, a point where you can create something. And that's exactly what I am trying to do, or at least asking how/if I should do it. And then I let them know where to start. That's what I want.
    Thanks.

Maybe you are looking for