DPS DSCC doesn't show operational status

I have DPS 6.3.1 running against 4 6.3.1 directory server instances. On the data sources page of DSCC, the 'operational status' column shows 'Could Not Retrieve Status' for all 4 instances. I've tried upping the log level on the DPS server to see if I could figure out what is causing this. Does anyone know how DPS (or DSCC) goes about figuring out what should be in that column?
Thanks

We don't have a single dscc for all instances. This is because of a strict 3 tier network architecture we are required to have (to the point that tier 1 dps is not allowed to talk directly to tier 3 ds so we have a tier 2 dps pass-thru). So are you saying that dscc in our tier 2 dps environment has to be able to talk to cacaoadm in tier 3 to show operational status of the ds on the dps screens? I was definitely under the impression that the monitoring as configured in dscc, has the dps instances monitoring the ds instances and the dps instances would let dscc know the status. To me, I don't care if dscc in tier 2 knows that the tier 3 ds instances are up, I want to know that the dps servers can talk to ds.

Similar Messages

Office365 - PasswordNeverExpires status doesn't show any status

Dear all,
I have a question about office365 passwordneverexpire setting.
Normally, when I execute the command "get-msoluser -userprincipalname "UserID" |select PasswordNeverExpires ", I can see the status "True/False". But, in my case, it doesn't show any status.
Thanks,
Min

Looks like the "Administrative queues" implementation could have been planned around design time. Then the requests could be assigned and managed by different roles(groups) member with different access levels in OIM.
However, in my current setup - all workflows follows this rule 1) Route the request for manager approval 2) After successful manager approval, route it for application group approval (2nd step of approval). Implementation of "Administrative queues" in this setup looks difficult to me.
Any comment?
Thanks,

MRS (Multi Resource Scheduling) - Show operation status in Planning Board

Because the current MRS thread is some long and complicated I chose to move this question into a seperate thread:
Initial question:
Like many companies, it is not unusual at my customer for their Planners to create orders with multiple operations, particularly since many orders require different crafts to perform the work. When the Planning Board is launched and Planners lok at work scheduled for the past week they want to be able to see at a glance which operations have been completed and which operations, perhaps from the same order, have not and may need to be rescheduled. Their preference is to select "final confirmation" when using transaction IW41 and thereby set the operation system status to CNF when the work on an operation has been completed. They then want to somehow use this CNF operation status to drive something visual in the graphical Demand layout display and Resource layout display to enable the Planner to see at a glance that the operation has been completed. I've tried several approaches with configuration of abstract statuses and the user interface profile without success. My customer's interest in being able to see the completion status of an operation in the MRS Planning Board makes a lot of sense to me. I'm hoping someone can help me with a technique for modifying the Planning Board so that it displays the completion status of an operation in a visual way.
Response from Varun Verma:
Hi Mark,
The problem at your customers end is nothing new.
What you can do ( many other customers have done it in similar way ) is:
1) you integrate the status CNF into MRS.
Check the customizing: Basic Settings -> Assign ERP Objects -> Status
2) configure in MRS that for status CNF, the assignments and demands (only in item work list or Hotlist) is colored to GREEN (or any other color)
Check customizing: Set Up Scheduler Workplace -> Workplace Profiles -> Define User Interface Profiles
Thus the users will know visually, that the green colored assignments are already completed.
By the way, in your work list you can also filter the demands based on their status
Regards
Varun.
Followup question:
Varun,
Thanks for the response. I thought I had tried this but perhaps it's because in the UI profile I had not entered something in both the status groups for assignments and the status groups for demands. I have a bit more testing to do but it appears that the demand status now gets updated from the operation status of PCNF (linked to abstract status WORK_START) and CNF (linked to abstract status WORK_STOP). I also get a red bar (C4) for PCNF and a green bar (C1) for CNF. Do you have a better status group I should be using in place of C1 and C4? Status groups C1 and C4 give me a bar but it doesn't look like the demand bar with a outline and alphanumeric description of the demand, it's just a colored bar.
I know the work list can be filtered based on their MRS "planning" status, however, it doesn't appear to permit filtering by the status of the operation unless I add the operation status as an additional field in the worklist. Is there something I'm missing here? And even if it did, my customer wants to be able to see the CNF status indication in the Demand layout and schedule using the work centers so the worklist is not being shown like it is in the Resource layout.
Mark
Edited by: Mark Scott on Aug 10, 2009 3:35 PM

Hi Mark,
Well I assumed that you have confirmations integration active !! But I guess not because you say that the status is not integrated always.
What you need to do:
1) I assume you have SP05 or later.
2) Implement the user exit: CONFPM05. In the implementation of this exit you need to call FM: /MRSS/RSG_PM_ORDER_CONFIRM
3) Go to customizing: Basic Settings --> Assign ERP Objects --> Status
-- Here, define an abstract status (MRS Status) for confirmed and partially confirmed
-- map it to R3 status CNF and PCNF.
After this, whenever you enter confirmation for PM order from transaction IW41, the status will be integrated.
Now you can use the MRS statuses defined in step 3 to configure the colors.
Implementing the user exit CONFPM05 might require some technical input. But it is easy. Just a few double clicks and copy paste.
Contact an ABAP developer for the same.
This should solve your issue.
Regards
Varun

SE07 doesn't show Import status after upgrade to ECC 6.0

Hi,
we were on 4.7 and we recently upgraded to ECC 6.0 EHP4. When we were on 4.7, after a release, we used to monitor the import status of all the transports going in, using transaction SE07. Looks like this transaction wouldn't work anymore in ECC6.
I can access the transaction, but I cannot expand the "Execution" to see the status of the transports which went in today. 4.7 used to show all the transports which were impoerted on that day.
I know we can check the import logs by pulling up each transport, but SE07 will show you a consolidated list with all the detail and will be very easy to find what we are looking for.
We are on Oracle 11g on Solaris 10. Please help.
Regards,
Vijay

Hi Tony,
I donot think it is an authorization problem. I have tried with a test user with full permissions and also with DDIC user, but still the same.
Regards,
Vijay

3702E-Operational Status DOWN

Hi All,
When we tried connecting ap, its registering to the WLC 5508 with version 7.6.120.0. But it shows operational status as DOWN in WLC and blinking in red,green continuously. If i admin disable it, then it is coming UP and instantly goes DOWN.
Any Suggestion.

see whether you have correct country code configured on your WLC & connected AP is in the right regulatory domain.
Wireless LAN Compliance Status
Post the AP console output to see what's exactly happening.
HTH
Rasika
**** Pls rate all useful responses ****

My App Store Doesn't Show Any Thing , and not working .

Today I've Noticed that My App Store Application is Not Working , and even I Can't Click On any Tabs ,and all of menu bar items such as sign out,sign in doesn't work . and doesn't Show Loading Status Bar, and doesn't show any message as you see in this picture :
I've Tried There Solutions:
Reset PRAM
Delete App Store Cache Files
Signed Out of Itunes And and signed in again
clear History and web site data in safari
But Nothing Changed .
(Sorry My English is Not Good at all , But i'll be thankful if you help me )

Test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
Step 1
Sign in to the App Store by selecting Sign In from the Store menu. If you're already signed in, sign out and then sign in again.
Step 2
Log out or restart the computer.
Step 3
Remove or disable "LittleSnitch" or any similar third-party software that blocks outgoing network connections according to the developer's instructions.
Step 4
Start up in safe mode and log in to the account with the problem.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
After testing, restart as usual (not in safe mode.)
Step 5
If possible, connect to a different network and test.
Step 6
There are reports that resetting the PRAM may solve the problem in some cases. I can't confirm.

Jabber for Windows 9.2.1 Contact Away status doesn't show duration

.Jabber for Windows 9.2.1 Contact "Away" status doesn't show duration. I am wondereing if it is possible with Cisco Jabber client. Microsoft OCS client used to show.

Hi,
This is currently not supported in Jabber.
If you think that this feature should be in Jabber, you can open a TAC case and do Enchancment request with them?
Regards,
Srdjan

HT4623 I have an iPod with iOS 4.2.1 and would like to up date version 5. The pc I normally sync with has XP operating system. So I can't up date to iTunes 10. And my iPod doesn't show the software update button shown in the article. What can I do?

I have an iPod with iOS 4.2.1 and would like to up date to version 5. The pc I normally sync with has XP operating system. So I can't up date to iTunes 10. And my iPod doesn't show the software update button shown in the article. What can I do?

You cannot update it if you can't get the latest version of iTunes. Actually, the latest version of iTunes will run in XP if you have Service Pack 2. Also, you posted in the iPad forum, and your profile shows you have an iPad, but in your post, you say it is an iPod. Is it an iPad or an iPod?

So i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

so i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

If you have not already, I would shut down (power off) your computer. Do this to Reset your shuffle
http://support.apple.com/kb/HT1655
Start up computer. Run iTunes. Connect shuffle.
If you have added a new USB device recently (since the last time it worked properly), you may want to try disconnecting it to see if that makes any difference.

IW32 After business closer operation status not showing CLSD

Dear Friends,
I have a query here. For PM orders system status gets updated as per business transaction. Operation status also gets changed as per header status. But it is okay till technical completion and operation staus gets set as TECO. But after business closer of the order still operation showes TECO status in place of CLSD .
Any clues on this please? Is this the standard feature or I need to search for OSS notes to be applied?
Regards,
Siddhartho Raha

Hi,
That note is no longer released so you cannot see it.
Note 675240 contains an alternative repair report, at end of page 13 you can see similar update following the comment:
*    begin of TECO / CLSD handling
the following section does the update:
IF update = 'X'.
* create an entry in jest that the operations are TECO
   CLEAR wa_jest.
   wa_jest-objnr = <wa_jest_ov>-objnr.
wa_jest-stat = 'I0045'.
-Paul

Apple logo doesn't show on my facebook status., apple logo doesn't show on my facebook status.

How to show apple logo in facebook status?

Welcome to the Apple Community.
Sorry but which icon is it that sometimes doesn't show up.

I use Firefox to access the internet-but when I go off the internet but don't shut down, then go back on Firefox it won't open because "it is already running". Task Manager doesn't show that it is operating so I can't shut it off. What to do?

It is in the question but to repeat.
1. When I go online I use Mozilla Firefox
2. While I am doing other work, I usually close the internet.
3. If I go back on the internet and click on Mozilla it won't come up, stating that "it is already running".
4. Despite that, when I open Task Manager, it doesn't show that it is running so I can't shut it down or open it.
5. If I log off or shut off the computer, then after I log in or reboot the computer, I can open Mozilla.
Thanks from a Mozilla fan.

See "Hang at exit":
*http://kb.mozillazine.org/Firefox_hangs
See "Firefox hangs when you quit it":
*https://support.mozilla.com/kb/Firefox+hangs

ITunes doesn't show anymore downloaded status of apps

After I bought an app in iTunes, on the small tab beside the app, instead of the price showing 0.99, or whatever the price was, it used to say 'downloaded'.
This was helpful, so I knew right away which app I have bought and which I haven't, so I wouldn't need to download it again.
But now, it doesn't show this anymore. That little price tab shows only the price of the app, no matter if I already bought it or not. So if I forget that I already downloaded a certain app, I have to download it again (not pay for it, but anyway I waste my time and my monthly GB Internet usage).
What I did was, I just pressed the 'reset iTunes store cache' and 'reset all dialog warnings', from Edit/Preferences/Advanced Preferences, starting from the Edit tab of the iTunes.
What can I do now, to have again the specification 'downloaded' on the little tab of the already bought apps?

I am trying to get Apple support, but the first answer was total wrong. Apple support thought I want to remove purchase:
"I understand you would like to remove an iTunes Store purchase and I will do my best to assist you.
To hide or show items on your Purchased page, follow the instructions in these articles:"
I replied it with a more detail info. I will let you know if I get the answer from them.

External Hard Drive doesn't show up

hi.
i'm having an issue with my external hard drive. this morning i went to plug it in since that's where i store all of my music, and for some odd reason it didn't work. i have a feeling it's because the night before i unplugged it without ejecting it. my mistake, i know, but now the drive is all messed up. earlier i was able to view the volumes on it in disk utility, and before deciding to erased anything i plugged it into my sister's dell where i transfered everything on the drive. now, when i plug it in my macbook it only shows up in disk utility without the volumes, it doesn't show up on the dell anymore, and when i go to erase everything it tells me "operation timed out".
i'm at a loss of what to do. i tried restarting the macbook, unplugged the cables... nothing seems to work. i would really like to get the thing back to factory settings if that's possible. so if anyone can offer help, it would be most appreciated. the external drive is a 500GB Maxtor OneTouch

Try this:
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Set the number of partitions from the drop down menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
If you plan to use this drive on both your Mac and a PC, then format the drive MS-DOS rather than Mac OS Extended.

Kde doesn't show cd

Hey everyone!
I installed a fresh Arch with KDE on my new laptop and now KDE doesn't show, when a CD gets inserted. I can mount the CD via console and all works fine, but I can't mount it via KDE, because it doesn't show up the notification. USB devices working fine. Has someone an idea?
Best regards!

Ok, I reinstalled k3b with all its dependencies and now KDE shows me the cd. But burning isnt working. I get the following error
Senden der cue Datei nicht möglich
Manchmal hilft es den TAO Modus zu verwenden
If I use the TAO method, I get the following error:
Das Medium ließ sich nicht fixieren
Das Medium könnte immer noch lesbar sein
Versuchen sie bitte den DAO Brennmodu
And this is the long error log:
evices
Optiarc DVDRWBD BC-5540H 101A (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R doppelschichtig, BD-CD-ROM, DVD+R, DVD+RW, DVD+R doppelschichtig) [DVD-ROM, DVD-R sequenziell, Zweischichtige DVD-R sequenziell, DVD-RAM, DVD-RW Eingeschränktes Überbrennen, DVD-RW sequenziell, DVD+RW, DVD+R, Zweischichtige DVD+R, CD-ROM, CD-R, CD-RW, BD-CD-ROM] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Eingeschränktes Überschreiben] [%7]
System
K3b Version: 2.0.2
KDE Version: 4.5.5 (KDE 4.5.5)
QT Version: 4.7.1
Kernel: 2.6.37-zen0-ck-00276-g999b248
Used versions
cdrecord: 1.1.11
cdrecord
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.11
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'Optiarc '
Identification : 'DVDRWBD BC-5540H'
Revision : '101A'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x0040 (BD-ROM)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 3143680 = 3070 KB
FIFO size : 4194304 = 4096 KB
Speed set to 706 KB/s
Track 01: data 693 MB
Total size: 796 MB (78:51.94) = 354896 sectors
Lout start: 796 MB (78:53/71) = 354896 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Reference speed: 2
Is not unrestricted
Is erasable
ATIP start of lead in: -11625 (97:27/00)
ATIP start of lead out: 359849 (79:59/74)
1T speed low: 0 (reserved val 0) 1T speed high: 4
2T speed low: 0 (reserved val 5) 2T speed high: 4
power mult factor: 5 2
recommended erase/write power: 3
A1 values: 02 54 B0
A2 values: 52 D2 36
Disk type: Phase change
Manuf. index: 0
Manufacturer: Illegal Manufacturer code
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 4953
Starting to write CD/DVD at speed 4.0 in real SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
/usr/bin/wodim: CUE sheet not accepted. Retrying with minimum pregapsize = 1.
Errno: 5 (Input/output error), send_cue_sheet scsi sendcmd: no error
CDB: 5D 00 00 00 00 00 00 00 20 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 27 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x27 Qual 0x00 (write protected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.004s timeout 200s
/usr/bin/wodim: CUE sheet still not accepted. Please try to write in RAW (-raw96r) mode.
/usr/bin/wodim: Cannot send CUE sheet.
/usr/bin/wodim: Could not write Lead-in.
Writing time: 7.154s
/usr/bin/wodim: fifo had 64 puts and 0 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord command:
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=4 -sao driveropts=burnfree -data -tsize=354896s -
Best regards!

DPS DSCC doesn't show operational status

Similar Messages

Maybe you are looking for