DTP Born with Incorrect Real-Time Status

Hi Gurus,
What am I doing wrong? When I create a DTP for Real-Time Acquisition, I am getting "Real-Time Status" as "Incorrect" even with a DTP Type correctly set for Real-Time. I have no option to change it for following status:
- New, Without Data Package
- Ready
- Transport Package Read
- Transport Package
- New Transport Package to be Deleted
- Stopped
- Active
- DTP/Infopackage to be closed
I am having quiet few problems to set up DTP with Real-Time Data Acquisition.
Kind Regards,
Gilson

Hi
Not a Guru ,but wanna give it a shot..
Prerequisites for creating Infopackages -
Check
1)The DataSource for which you want to create an InfoPackage supports real-time data acquisition.
2)If you are transferring data into BI using the service API, you have already created an InfoPackage for initializing the delta process for this DataSource, and have completed the initialization.

Closing Requests in the Monitor for Real-Time Data Acquisition
Prerequisites
The daemon is inactive or has errors.
Procedure
In the context menu of the PSA or DTP request, choose Close Request
Barring all those steps mentioned above if I copy you properly ,I put 2 cents on the authorization issue related to RDA.
Check OSS note- 943898
IF at all the note applies to you ,since the patch is not released ,have to go ahead with correction instruction.
Hope it Helps
Chetan
@CP..

Similar Messages

Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q with a real time mode but it is not working but when i run it with uploading it into the PXI it save in to the file

Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q and DAQ NI PXI-6229 with a real time mode but it is not working but when i run it without uploading it into the PXI it save in to the file please find attached my vi
Attachments:
PWMs.vi ‏130 KB

other problem is that the channel DAQmx only works at real time mode not on stand alone vi using Labview 8.2 and Real time 8.2

Skill Group Name is not coming on Cisco CTI Tool Kit real time status

Hi,
I have UCCE 9.0.3 in my environment but when supervisor is monitoring agent state on CTI Toolkit Team Real Time Status we are not able to see Skill Group name.
For your reference I have enclosed screen shot of that.

Hi,
first, read this document: Recommended Tracing Levels for Troubleshooting IPCC Issues. Apply the recommended trace levels to the following services:
CTI OS Server
CTI Server
But first take note of the original values (so you can switch back to normal tracing).
Dump the logs for both the above services: How to Use the Dumplog Utility.
For instance: dumplog ctisvr /hr 1 /of c:\temp\ctisvr.log
Post the logs to here.
G.

How come you can not use more than 126GB of a 1.5TB diskdrive with LabVIEW Real Time?

How come you can not use more than 126GB of a 1.5TB diskdrive with LabVIEW Real Time?
This is only 8.3% of the available disk drive space!
http://digital.ni.com/public.nsf/allkb/E7E2F5657B6026358625750B007201A6?OpenDocument
National Instrument's solution is either reformat you drive to less than 126GB or replace the drive with one less than that size.
Please NI, tell me you are going to fix your LabVIEW Real Time soon, and that we won't have to wait for LabVIEW RT 9.2.1 in 2011 for this one to be fixed.
http://upload.wikimedia.org/wikipedia/commons/9/90/Hard_drive_capacity_over_time.svg
Drives as large as 126GB or more have been around since about mid 2002. That's about 7 Years now and LabVIEW Real Time STILL can't use drives larger that 126GB! Please NI. Do something.
We deserve fixes to the old versions of LabVIEW RT. How about updates to LabVIEW RT. Such as 7.0.2, 7.1.2, 7.6.2, 8.0.2, 8.2.2, 8.6.2.
We don't need new features or versions of LabVIEW RT such as 9.0 until we have some of bugs fixed in the existing versions.
Kevin.
Message Edited by kmcdevitt on 05-29-2009 03:39 PM
Solved!
Go to Solution.

Coq rouge wrote:
NI is not making the Real Time OS in house. I do not remember which firm that is making it. Anyway you are allowed to use a hard drive that has been partitioned. And 126GB is some space is it not? I remember Bill Gates declared one time that 640Kb ram should be more than enough for any PC application also in the future
Coq Rouge (formerly t06afre),
The RealTime OS is an NI Product that is purchased from NI.
NI may or may not outsource design, developement, or manufacturing of the products that it sells under its own Company name.
For this reason I would be concerned if I were a PXI Embedded Controller designer/developer in the United States.
Yes, 126GB is some space. I see that there are now 2TB drives available. 126GB would be 6.3% of a new 2TB drive. Should we all be happy with being able to use 6.3% of the available drive space. Moore's Law seams to be alive and well. Drives larger than 126GB have been readily available for 5 or 6 Years. This should not be a surprise to NI. Why don't they do something about it.
Thanks for the trivia on Bill Gates. I must have missed that one since I don't try to keep up with Microsoft. I believe that he is a wonderful person and he and his family are doing wonders for the world in their "retirement". The world needs more like him.
What I do remember is Steve Jobs telling us that we would never need more that 128MB and that we would never to need to do anymore software development because everything was already in the "ToolBox".
McKevin.

Supervisor Desktop - Real time status shows the deleted agents

Hi All,
Recently we modified only the agent IDs for few agents.In ICM we just edited the previous entry. We have not deleted and re created it. Now the problem is the in "Supervisor Desktop - Real time status" the old entries are also reflecting in logout state. Exit_OPC will help us to remove this stale values. But is there any other metheod to to achieve this without impacting the production?
Regards,
Adithya

Hi David,
Thanks for your response. We cannot reinstall the Supervisor desktop there are multiple supervisors for this team. Will wait and check if the stale entry goes automatically. Please let me know if u come across any other process which will help in doing this.
Regards,
Adithya

Synchronise time in array with the real time from computer

i need help in syrnchonising my array and the real time running in my computer
As stated in the text file attached,
12:32:30 AM 0.38 1.14
2nd column is wind speed, 3rd is gust speed.
i would like to display the wind speed in a gauge with the right values. like for example, at 12:32:30 AM OF REAL TIME, NOT BASED ON THE TEXT, i would like to display the 0.38m's of wind speed in the gauge.
how do i sync the time in array with the real-time?
i have attached a program i made so far. its abit messy. im still a student, need a lil help
Attachments:
Wind Speed and Gust Speed.txt ‏13 KB
Time and MaxMin.vi ‏18 KB

wali123 wrote:
wat u mean duplicate?
Don't continually post the same question over and over. If you have new information, add it to the original thread. Did you actually click the link under the word "duplicate"?
Chopping up a discussion about the same thing into several threads (like here is this thread, but also here and here) serves no useful purpose. It will not increase the chance of a good answer, in fact most people will simply ignore it.
Imagine if everybody else would post like you! Every discussion would be if three different places and we would have three times more threads.
LabVIEW Champion . Do more with less code and in less time .

Can I use third party DAQ boards with Labview real time?

I have an Adlink DAQ 2010 card that I curently use with labview. Will this card also work with Labview real time? What requironments are there for 3rd party cards to work with Labview real time?
Thanks!

Hello George,
Here is a great link for you to take a look at: Can I Use a Third-Party Device with LabVIEW RT?
Have a great day,
NathanT

MultiProvider with two real-time InfoCubes?

Hi,
I created a multiprovider with two real-time Infocubes. I need to create a formula in FOX editor where I have to update only one InfoCube. Is it possible? If so, I am looking for syntax with InfoCube name in the formula. The KeyFigures have the same names in both InfoCubes.
Any help would be appreciated.
Thank you,
Vidya

Hi Pratyush,
I am using IP. I created Aggregation Level, Filter, etc. It created a characteristic "0INFOPROV" and I used that cha. to read data and to write the data. It did not work.
Here is the problem.
- We have one basic cube (history data: HCUBE) and two transactional cubes (actual data: ACUBE and plan data: PCUBE)
- Created a multiprovider (MULTI) for HCUBE, ACUBE, PCUBE
- Also created Agg level and filter
- Note: Three cubes have the same Key Figure (0Amount)
- Created a planning function and tried something like {KF, PCUBE} = {KF, MULTI} (as suggested by Andrey)
- Task is to read data from HCUBE and ACUBE and only write to PCUBE.
- I am able to read data but unable to write data.
Any ideas?
Thank you,
Vidya

Help needed with CVI real time

Hi,
I am new to CVI real time and need help related to this. I will explain my scenario:
1. I have few configuration files (INI). Need to validate the files (range checking..etc) during start of the application.
2. When user clicks "START" in the user interface on the host machine, I need to generate outputs (analogs/discretes...) based on the settings in the config file and read some inputs from other instruments. ( I/O tasks like generating outputs/reading inputs i am planning to perform in RT side)
3. From the user interface, user can also change the config files. if user changes the files, again file validation needs to be performed. After changing the files, if user clicks START, need to take the newly enetered config files to perfom I/O tasks.
4. I am NOT using reflective memory for my application.
I am confused in the following area:
1. File validation during startup , do i have to perform on both host and RT side?????
2. if configuration files are changed in the host side by the user, how i have to send this latest file names to RT??? I think i should not send file names, i need to read from the file and its contents i need to pass to RT....Pls correct me , I am not sure about this....
3. If I have to send file contents to the RT, how I have to do that....means i have to use structures,..???
Please guide me. Any help would be highly appreciated.
Regards,
haari
Solved!
Go to Solution.

Hey haari,
1. File validation during startup , do I have to perform on both host and RT side?????
This depends on the full range of responsibility for the INI files. If they are all needed simply to change what the I/O tasks are for, then you would technically only need to validate the INI file contents on the RT side. You could, however, validate on both sides if you wanted to. However, I would probably set it up such that I send a validation command to the target, have the target run a component of the code that validates the INI contents based on how I instructed it, and then return a message that says whether or not it met the requirements I specified. However, if you are concerned with offloading that process to the user desktop (instead weighing down the RT controller performance), you could FTP the file off of the controller and perform the validation process on the host side.
2. if configuration files are changed in the host side by the user, how i have to send this latest file names to RT??? I think i should not send file names, i need to read from the file and its contents i need to pass to RT....Pls correct me , I am not sure about this....
You can send them to the target over FTP. This can be done programmatically, through MAX, command window, or a Web browser.
3. If I have to send file contents to the RT, how I have to do that....means i have to use structures,..???
This is basically addressed in answer to question two. You would not need another structure in your RT code to handle the FTP receive component as this is handled by the FTP Client/Server communication. However, in the event that you successfully FTP a file to the target, you should likely send a message from the host to the target so that the target can respond accordingly and reload the file, reestablish the I/O values, run an idle procedure, or do whatever you like.
Hope this helps. Have a great day!
Tim A.
National Instruments

Experimenting with FCP/ Real time rendering question

Hello, I am preparing to purchase a Mac Pro and spent some time at the local mac affiliate store playing with FCP and motion.
In fcp I took two clips and dropped them in the timeline, adding the 3d cube transition, and some filters to both clips.
I was looking at performance of real time rendering on teh base config of the MP I plan on purchasing.
I then added another clip above these two, intending on dropping the opacity to further push the RTR (real time rendering). This clip overlapped the transition of the two other clips in v1 and v2.
When attempting to play the timeline the viewer window now said "Not Rendered"
My question is:
Is there a limit to how many tracks can be run under the RTR? Why did I get this message?
My main reason of the move to a Mac Pro is to get away from constantly pre-rendering.
Thanks everyone in advance!

In fcp I took two clips and dropped them in the timeline, adding the 3d cube transition, and some filters to both clips.I was looking at performance of real time rendering on teh base config of the MP I plan on purchasing. I then added another clip above these two, intending on dropping the opacity to further push the RTR (real time rendering). This clip overlapped the transition of the two other clips in v1 and v2.
<
Sounds like you know what you're doing and what you expect. A factor that has not been mentioned yet, besides RAM, prefs and drive speeds, is your video format.
Also, the new rev of FCP is taking advantage of tons of processing overhead, vastly increasing the amount of stuff you can do in real time. However, real time is largely a preview operation, regardless of the machine or system, unless you are using proprietary codecs, such as Media 100, that might be hardware-assisted. Output is almost always a rendering issue, multiple stacked or processed layers require the creation of new media.
The only way you're going to be able to decide if Macintosh and FCP are right for you is to demo thoroughly and that requires using your own footage.
bogiesan

Jmx with java real time

Hi David,
my question for now is very general.
can we use jmx with jrts???
Gabi

Hi Gabi,
Some additional information:
- JavaRTS does support the JMX protocol
- JavaRTS supports most of the monitoring & management functionalities provided
by HotSpot MBeans
- some functionalities are disabled by default because they would create jitter (like
getting the stack trace of java threads). Default can be changed through the
realtime.debug MBean)
- JavaRTS comes with a few additional realtime specific monitoring beans.
Note that JMX relies on threads to do its work. These threads are not real-time.
Hence, if the realtime threads (including the RTGC) are consumming all the CPU,
you may not be able to call MBeans to see what is happening and take corrective actions.
Bertrand.

Can you use event case with labview real time?

I have a real time application I am putting together and until recentally have concentrated on getting the data acquisition working as expected.
I am using a PXI-8183 in a 1031 chassis.
I am now trying to add the functionality for setting up the system in the form of a GUI remote front panel that I connect to with a host laptop. I am connecting with the host as expected and it seems to be working well in that respect.
My problem is with event cases, operating in a while loop on the target. They just dont seem to want to trigger when i click on a button I have set an event for.
I have looked through the documentation and cant see any reference to issues with event cases on rt, but I feel I am missing something fundamental. Can anyone help?
Regards,
Barry

look here maybe:
http://digital.ni.com/public.nsf/allkb/42B70D2D0C4B568586256E2F0051441D
Harold Timmis
[email protected]
Orlando,Fl
*Kudos always welcome

How do I talk to 1-Wire devices with LabVIEW Real-Time?

Hello, I'm trying to use LabVIEW Real-Time to talk to some older 1-Wire devices that my company has previously communicated with using C code. We are currently developing on a cRIO and are trying to use a Dallas Semiconductor 2480 serial port device to talk to some iButtons and a secure SHA 1-Wire device. I have run into a few problems where the 1-Wire device stops communicating and just repeats the data sent to it. I was wondering if anyone has successfully created any VI's to talk with 1-Wire devices via the serial port that do NOT use any kind of Java or .NET or Windows based device drivers supplied by Dallas Semi. A last resort would be that we keep the C code and place it in a block in LabVIEW and run it as is but I would prefer to have some LabVIEW-native code. Any help would be greatly appreciated. Thanks.

Brian_T,
Thanks for that link about compiling a shared library for use on a VxWorks cRIO. The only thing they mention that I don't understand is this bit:
"GNU toolchain distributed with Wind River VxWorks"
I have been unable to locate a compiler for VxWorks so I am assuming that is located in this GNU toolchain thing? Does that come with the cRIO? I think I noticed a VxWorks C compiler somewhere else online but we're talking a totally different product I would have to purchase, assuming it would even work. I guess once the stub and the shared library are all good to go, I just call the C functions in the shared library and when it comes time to talk to the serial port, just slap a VISA Read/Write VI on the block diagram. I've been using a cRIO and COM1 access for some time now so I do understand at least that much. Let me know how to get ahold of this "toolchain" thing. Thanks.

Problems with Creating Real-Time InfoCube in BI 7.0

Hello, Everybody,
I try to create Real-Time cube for BW-BPS planning, but when i want to insert a key figure into real-time info cube i get error:
Short dump has not been completely stored(too big)
Exception condition "Node_related_missing" raised.
Could You help me?
Thanks in advance,
Best Regards,
Arunas Stonys

Hi Arunas,
I think you are not on SP10. you may need to implement the SP10 or advance correction as in this note:
Note 968097 - Error in BI metadata maintenance (InfoCube, MultiProvider)
Symptom
Note that the attached corrections cause follow-up errors. You must also implement the corrections from Note 971918.
You are in the maintenance dialog for an InfoCube or a MultiProvider. When you enter new key figures in this provider, a program termination occurs with message "NODE_RELATED_MISSING" in class CL_RSO_DATA_TREE.
This problem occurs because the InfoProvider does not contain a unit dimension yet and the system tries to insert the relevant unit into the unit dimension (that does not exist).
Other terms
Transaction RSA1, RSDCUBE, RSDMPRO
Reason and Prerequisites
This problem is caused by a program error.
Solution
SAP NetWeaver 2004s BI
Import Support Package 10 for SAP NetWeaver 2004s BI (BI Patch 10 or SAPKW70010) into your BI system. The Support Package is available once Note 0914304 "SAPBINews BI 7.0 Support Package 10", which describes this Support Package in more detail, has been released for customers.
In urgent cases, you can implement the correction instructions.
To provide information in advance, the note(s) mentioned above may already be available before the Support Package(s) is/are released. In this case, the short text of the note still contains the words "Preliminary version".
Thanks,
Raj

Is Ardence RTX required when I use PCI-7831R with labview real-time module for RTX target

I am new in the labview real-time field. I want to use labview real-time module for RTX target on only one desktop. My card is PCI-78331R. Is Ardence RTX necessary? Why I cannot find my card in the MAX after I configured the RTX?
Thank you very much.

Hi Ziaozhongda,
You must have the RTX runtime engine installed before the LabVIEW Real-Time RTX module will install. Additionally, you should follow the instructions in the "Using the NI PCI-7831R with the LabVIEW Real-Time Module for RTX" section of Getting Started with the NI 7831R (page 8).
Please see Configuring Hardware for Use with RTX.
Also useful is "How Can I Validate That My PC Will Run RTX?

DTP Born with Incorrect Real-Time Status

Similar Messages

Maybe you are looking for