Dual interface card communication

Hi,
I am new to java card technology and going to work on SmartMX dual interface card.
(http://www.nxp.com/products/identification_and_security/smart_card_ics/smartmx_dual_interface_controllers/P5Cx009_P5Cx072_FAM_SDS.html)
I would like to know working of dual interface card. Is it possible to write data on java card Via NFC or vice-versa?
Also, I want to know how to program java card & what kind of hardware I need for programing java card ?
Edited by: 909587 on Jan 23, 2012 12:16 AM

I would like to know working of dual interface card. Is it possible to write data on java card Via NFC or vice-versa?You either need to communicate with an applet on the card (that you develop) or interface with MiFARE. You SmartMX should have MiFARE as well as Java Card. What are you trying to achieve? If you can provide more details we may be able to add more information on how to do it.
Also, I want to know how to program java card & what kind of hardware I need for programing java card ?You will need a PC/SC compliant smartcard reader. You can get dual interface readers with contact and contactless interfaces.
Cheers,
Shane

Similar Messages

Loading mifare application to java dual interface card

Hey,
I have a jcop dual interface card. I have successfully loaded a javacard applet and the data. When i try to update and read binary, im getting a 6985 response.
this is the command
#Reader Authenticate
FF00000009090000000000000000
9000
#Mifare Load Keys
FF0000000A07000060FFFFFFFFFFFF
9000
80860000050100040000
9000
80D600041036383132313031323341443931383833
9000
80860000050100080000
9000
80D60008102C373837303031303130333030303231
9000
thanks in advance

these are pseudo APDUs interpreted by the card reader. The mifare protocol is specific an proprietary, it has nothing to do with APDUs.
if your card is a dual interface javacard that supports mifare, then the card manufacturer may assist you on how to access the mifare memory zone from javacard.

Software and Interface card required for DNP3 communication with a protection relay?

I am looking to build a SCADA Master to perform DNP3 communication between the Master and an Outstation device. I would like to know apart from the Ni - Industrial comm software is there any other Interface card I require to accomplish this task?

According to this article, that’s all you need. Just make sure you run applications as an administrator and that you don’t have any type of network restrictions. Since you have it installed, I encourage you to test the functionality/connectivity through the shipping examples, which are located on your hard disc at ...LabVIEW XXX\examples\DNP3 folder (also visible at the NI Example Finder). You can modify an example VI to fit an application, or you can copy and paste from one or more examples into a VI that you create.
Alejandro | Academic Program Engineer | National Instruments

MSI Dual-Net Card and Communications Slot

Hey all,
ok, i want the MSI Dual-Net Card...i have HEARD that you need the MSI Communications Slot for it to work...is that true???
because there is absolutly NO MENTION of this on either the website or even in the manual for the card...
the manual even shows a picture of the card being installed into a NORMAL PCI slot...

Quote from: Klodrik on 24-August-05, 02:28:28
Do u have IVT corp. BlueSoleil prog.? On my cpu, when i start Bluesoleil, it says "please insert a bluetooth device", but when i push the orange ball in the middle, i says " Invalid operation", and most of the menus are grey, like Tools, My services and My bluetooth. I cant even use "Find device". I'm trying to connect to a cellphone which has bluetooth ( Ericsson k700i ).
yep, thats wat i have...and its the BEST Bluetooth software i've used...we have 3 Bluetooth USB Dongles in my house, and the software for them all (compared to this) is...well, just crap...
did u plug in the USB header??? for the bluetooth to work, it has to be connected to a USB header on the motherboard...
and i assume you've checked device manager to make sure the driver is installed...if not, do it...
BTW, i know wat was wrong with my Wireless Network...i had the Wireless Antenna and Bluetooth Antenna plugged into the wrong places now my wireless has full strength!

Setting Up Dual NIC Cards? Benefit?

Hello Everyone,
I know that the Mac Pro line comes with Dual NICs and I was wondering how do I set these up to be useful with my Cable Modem and Router? Can they be used to get more speed or are they used together in some other capacity.
I really appreciate anyones help and expertise.
Many Thanks,
Chris

The normal use of dual nic interfaces would be to run double instances of a given server on disparate IP numbers. Dual NIC's are generally employed in order to attach multiple IP addresses to a single machine.
Another potential use for dual NIC's is internet connection sharing, where your Mac Pro acts as a kind of router; again also this could be used for attaching one NIC to print services and the other NIC for LAN/WAN access.
OK, actually there are a whole bunch of good reasons for dual NIC cards, but 'doubling your bandwidth' is really not one of them. Believe me, unless you are on a direct fiber OC-10 20 foot from your ISP's NOC, then your existing single NIC has 1000 times the bandwidth of your incoming WAN connection.
It is likely possible to interleave dual NIC cards between two machines for bandwith purposes; but if that were going to be the canse, just identify one as "in" and the other as "out" (both machines would have to have dual NIC's to make this mean anything) but again, I honestly do not see a real world use for this...
Message was edited by: psalmsmith

Expressway-E VMWARE dual interface

Hi All
There is a firewall between DMZ and Internal network. We have used expressway E as dual interfaces one is in the DMZ and other is in the internal network.
Clint is insisting that there is security risk deploying expressway in this way? Please advice
Thanks

Your Client is right!
Expressway E is supposed to be connected to the DMZ network.
If you can use an offical ip without nat address you only need 1 interface.
If you have to use nat then you will need two dmz networks.
You can find information within the Configuration Guides:
http://www.cisco.com/c/en/us/support/unified-communications/expressway-series/products-installation-and-configuration-guides-list.html

Dual band card - U400

I have upgraded to a dual band router. I was wondering if it is possible to replace the card in the U400 with a dual band card. I know it will fit based on the size/type of card but I didn't know if it had the correct antenna. I don't want to purchase and install the card to find out it isn't able to use both bands. Any advice would appreciated. Thanks!

hi perrinjcat,
Welcome to Lenovo Community Forums!
Lenovo System has a limited support for Wifi adapters it has a Whitelist of parts compatible and those parts are marked with an FRU number,
Here are the parts stated to be compatible on your system
Highlighted are the FRU Number,
NOTE: The WIFI card should be marked with the listed FRU.
Same part model with no FRU will not work.
Best Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

3845 Router do not work with NME-X23ES-1GP Interface card

Need help!
I Trying install interface card NME-X 23ES-1GP on 3845 Router. I installed this card in slot 4, but router could not communicate with this card.
IOS version in Router 12.3
Here is results show diag command:
Slot 4:
Unknown (type 1187) Port adapter
Port adapter is disabled deactivated
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-25011-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : FOC090009VC
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : NME-X-23ES-1G-P
Version Identifier : V01
Base MAC Address : 0013.8088.9f80
MAC Address block size : 128
EEPROM format version 4
EEPROM contents (hex):
Possibly IOS release too old?

Thank you for link. I read all information on this link. But I can't solve the problem.
Commands "show version" and "show flash:" show my the IOS image file version on Router (but not on interface modules). Here is Routers IOS image:
c3845-advipservicesk9-mz.123-11.T5.bin
I Can't connect to and open a session on the interface module. Command service-module interface slot/port session don't work.
What I should do next?
May is ncessarily upgrade Software on router?
Here is results show version and show flash:
BIG1#show flash:
-#- --length-- -----date/time------ path
1 29801400 Jun 28 2005 04:47:46 +00:00 c3845-advipservicesk9-mz.123-11.T5.bin
2 1651 Jun 28 2005 04:55:18 +00:00 sdmconfig-38xx.cfg
3 3085312 Jun 28 2005 04:55:40 +00:00 sdm.tar
4 763392 Jun 28 2005 04:55:56 +00:00 es.tar
5 820224 Jun 28 2005 04:56:10 +00:00 common.tar
6 1038 Jun 28 2005 04:56:24 +00:00 home.shtml
7 113152 Jun 28 2005 04:56:36 +00:00 home.tar
8 749101 Jun 28 2005 04:56:52 +00:00 256MB.sdf
9 1208320 Jun 28 2005 04:57:08 +00:00 ips.tar
27451392 bytes available (36560896 bytes used)
BIG1#show version
Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.3(11)T5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Sat 02-Apr-05 15:14 by yiyan
ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
BIG1 uptime is 57 minutes
System returned to ROM by reload at 07:11:45 UTC Tue Jul 12 2005
System image file is "flash:c3845-advipservicesk9-mz.123-11.T5.bin"
Cisco 3845 (revision 1.0) with 223232K/38912K bytes of memory.
Processor board ID FCZ0927714C
2 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
62720K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102

Using NI488.2, is it possible to configure the Interface card as a 'Listen-only' device

At one time,the older gpib.dll supported the ability to change an interface card register in order to allow the card to function as a Talk-Only or Listen-Only device. I want to do that with version 1.7 of NI488.2. How would I do that? If I switched to VISA, would I be allowed to do this?

Hi..
We use a number of different NI Gpib cards here at work in conjunction with some RF test equipment in a development environment. Most of this equipment will only work in a Talker-Only mode and are meant to dump data to a Pen Plotter. My objective is to write a universal application that will allow the PC to emulate a plotter in a 'listen-only' mode. Some of our PCs are older ISA versions (Win98,etc) where others are PCI (Win2000,XP). I want to write the software so that any of these platforms could be used.
Any suggestions would be appreciated..
Jim

How good is a Macbook Pro with dual video cards for gaming?

I've been a PC guy my whole life (aside from my iPhone which I love). My gf has been pushing me to try out a mac and considering how my PC laptops have a pretty good track record of dying on me or encountering some other problems after a year or two, I can't help but consider making the investment. The only thing is, I'm a big gamer and usually get the latest games. I'm not super tech savvy though I do my research and get a sense of what kind of specs are better and worse.
In terms of gaming, I always assumed that more ram = better. In that sense, I'm a little put off that even the most expensive MacBook Pro only comes with 4 gigs of ram (which is what my year and a half old laptop has now) especially when it seems most newer laptops have 8 gigs minimum for a fraction of the price (and 16 gigs if you're willing to spend as much as you would on the most expensive macbook pro). Does RAM somehow work differently on a Mac or is it truly that little?
Also, how does the whole dual video card thing work, does that mean I'd be having the power of those two cards put together?
Personally, I've been leaning towards the Asus G53SX-NH71 because I can buy it for less than the cost of the cheapest macbook pro and as far as gaming purposes go it seems to have more power than even the most expensive Macbook which costs over double the price.
Am I missing something here? Do the dual video cards really bring that much to the table or for gaming purposes am I better off with a PC?
Thanks.

I've been watching this forum for years, and I'll have to say that gamers are not a big group around here. A few things. First, getting 8GB of RAM for the MacBook Pro is cheap. Most people either don't care, pay Apple to do it, or, like me, DIY. The max you put in a MBP is 8GB, so no 16GB, unless you were looking at the iMac or MacPro.
Second, there is no dual video card in a MacBook Pro. There is an integrated video card, an Intel HD3000, which shares RAM with the CPU, or a discrete video card, an AMD, various versions on different MBP's. The Intel is for low battery usage. The AMD is more powerful, and it's to be used when you've got power. The video card has more applications than just gaming, but also in video and photo editing.
No one here is going to talk you into one platform or another. If you are only going to game in Windows, then it's a waste to get a Mac. If you're going to game in Windows but want the Mac side to do everything else, the build quality and elegance of the Mac will far exceed most products out there. You can run Windows in Boot Camp natively, and as I understand, gamers love it, because the Mac is actually a better Windows machine than most Windows machines. But I don't play games, so I have no proof.
So the choice is yours. And we could argue all day long about the side by side comparison of a cheap Windows machine vs. the Mac. You are using the price vs. price comparison that is a false dichotomy, ignoring how one values various features. For example, the trackpad on a MacBook Pro far exceeds (and I mean light year exceeds) anything on any other laptop out there.
I spent 10 minutes answering your question. I'm not debating you on x vs. y. The choice is totally on what you're going to do. Most of us are trying to contribute to the world, so gaming is low on the needs list.

Message Interface and Communication Channel are not getting in RW B

Hi
I have created a sceario in which i have created following things
2 - External Definition of Same XSD
2 - Data Types
2 - Message Types
4 - Message Interfaces
2 - XSLT mappings
2 - Interface Mapping
I have created on two scenario objects in XI ID.
But In RWB i can see only one sceario message interfaces and communication channels but the for other scenario MIs and Communication channels are not visible in RWB
I have created all the things in only one Namespace.
What could be the problem .please help me
Regards

Hi,
Have you activated it?
Can you see it in SXI_CACHE?
If one is no please run report SAI_CACHE_REFRESH
Kind regards,
Wojciech

Photoshop CS6 have problems with my dual graphics card

I'm currently using photoshop cs6 on my laptop (hp pavilion dv4 3114 ), and this laptop has dual graphics cards(one is mobile intel hd graphics, the other one is ati hd 6750), it ususlly switches to the faster one when games are running or some software that requires a lot of graphic work. But this time I have already set in the graphics card profile to let photoshop use the faster one, but when I launch photoshop cs6 it tells me that the graphics card is not officially supported, as you can see this in the screenshot.
Then I turned to photoshop's preference(performence) and found it only identifies the mobile intel hd graphics. I'm currently using photoshop for designing large posters so performence is very important for me. Is anyone know how to solve this problem so that photoshop can run with the highest performence?

II can't imagine how these computer companies expect to fully integrate GPUs from two different vendors, but they're trying. To me, knowing a bit about how display drivers are implemented, it seems an impossible task.
I hve heard (in the context of Macs that have this option) that disabling the low power options so that only the more powerful GPU is active can help. I don't know if that can apply to your system, but it might give you an idea of a place to start looking.
Another thing might be to try to find whatever settings it offers for "affinity" and set it so Photoshop and its cousins use just the ATI GPU exclusively. It might be the "switchover" process that is causing the problems.
Good luck.
-Noel

How to get dual graphics card to work together?

I have an L series satellite with dual graphics card that wont work together. Its an AMD Radeon 3400m apu with an HD 6520G integrated , and a 6400m discrete graphcs card.
The 6400m will never turn on, I have used amd system monitor to see if it is ever used, but it never is.
Even when the 6520g is at full load it wont turn on.
Any suggestions would be helpful.
Thanks.

Hi
As far as I know this theme has been already discussed here in the forum and the switch between internal and external ATI GPU is not supported.
Just the Optimus technology designed by nVidia is supported
So you can switch between Intel GPU and nVidia (if both would support the Optimus technology)

Dual SIM cards

I read somewhere that the OS for iPhone supports dual SIM cards.
After a quick search i found a (french?) website that sold adapters that could fit two SIM cards in the slot of the iPhone.
They claim that they havn't fully tested this on the iPhone 3G and 3Gs.
Fitting the SIM cards in the adapter requires cutting them down in size and cutting a hole in the SIM holder for the iPhone.
As for the cutting of the SIM cards, one can always buy a replacement, but if this damage the inside of the iPhone, I don't know how to deal with this...
Does anyone have tried this, and have som input?
Is it recomended or not?

I'm not sure how they could do this with only one SIM card making contact with the internal connections at any one time. No amount of on screen menu would activate a SIM card that isn't physically making a connection to the internal connections.
They would have to make some sort of adapter which connected both SIM card to a common contact port which lined up with the internal SIM connections within iPhone. Amending the software to have an option to switch SIM goes against the OS Terms and Conditions. Unless the application is authorised by Apple and is available through the App Store, any damage caused as a result of trying this would render your warranty VOID.
I would not recommend trying this, but it is your iPhone and it is your decision (and money)

Apple should really come up with a dual sim card. Has anyone tried to use the dusl simcard adaptor?

I see many ads for the dual sim adaptor, also it is being sold on some flights. Has anyone tried one? Instead of putting better cameras on their iPhones, Apple should really concentrate on making a phone with dual sim cards ( without asking exhorbitant prices) which will make travelling so much easier.

Tell Apple:
http://www.apple.com/feedback/iphone.html

Dual interface card communication

Similar Messages

Maybe you are looking for