Early allocation of numbers to Measuring point

Hi all,
While creating the measuring points, the system generated internal numbers get alloted to MP, though in creation stage.But I have not saved the MP and came out of the transaction. But my number got wasted and when try to create new MP a new number is getting alloted. How to prevent this?
((I don't want to lose numbers as these are in symmetry for two different systems and has to be corelated by us , as & when required.))
I didn't find any thing in customizing (like what we have for notification-early number allocation).
Please reply.
Raj

Hi,
You cannot adjust this through customizing, measurement document numbers are always issued early. If document not saved then that number is lost. Buffering can also cause gaps to occur in the number range.
See note [307437|https://service.sap.com/sap/support/notes/307437] for a full explination on measuring document numbers. See note [62077|https://service.sap.com/sap/support/notes/62077] about buffering.
-Paul

Similar Messages

External number range for measuring point

Hi experts,
How to assign external number range for measuring point ?
Regards
Shashi

I have just checked and the measurement point number is linked directly with tthe object for eaxample equipment and when I tried this I got the same result the system defaults the number based ont he internal number range.
This being the case what is the business requirement that you need to use external numbering as this may help and someone may be able to assist either with an answer to the problem or an alternative solution.
SAP documentation as follows:
Create Number Ranges for Measuring Points
In this step you define number ranges for measuring points.
Notes
As the numbers for measuring points are assigned internally, you should work with the standard settings. If you want to make changes, you should always use number range 01.
Jim
Edited by: JamesPetrie on Feb 28, 2012 2:45 PM

Gap in measuring points

Hi forum:
I created measuring point 45 (internal), when I display measuring points list I realize the earlier number created is 39, meaning there is a gap of 6.
What can I do to avoid this gap in measuring points?
Regards.

This happens in Measuring Points, because any attempt to create a MP and cancel it without saving, consumes one number. At the same time there is no significant disadvantage due to missing numbers in MPs. You may sort or search them by the Equipment numbers.
Regards
Jogeswara Rao

Accepting date as a measuring point

Please guide as to how does one accept date field as an input in measuring points.Have made a characteristic with date format,yet while creating a measuring point with the said characteristic , displays an error
" Only characteristics with a Numerical format can be used "
awaiting an early reply,

Hi pshthecoolest ,
You cant declare DATE with Date format as Characteristics , as per Std SAP.
Work around will be Create Char CT04 DATE , with Numeric format with Template (8), assign appropriate unit of Measurement , that you need to create separately t code CUNI.
But above all why you required to put reading as a Date in measuring point ?
Riyaj
Edited by: riyajmaner on Feb 8, 2011 12:51 PM

Measuring Points extraction

Hi all,
Im trying to use the PM_MEASUREMENT DataSource. It works pretty well with Measuring Points linked to Functional location. However, I have some Measuring Points that are linked to Equipments and those Equipments have no connection to Functional Location. For these Measuring Points no data is being extracted at all.
Is there any restriction with the DataSource PM_MEASUREMENT that makes it only to extract data for Measuring Points linked to Functional Location?
If not, does any of you have any idea about what is going on here?
Thank you very much,
Claudiomar

Thanks for your replies.
Saurabh: High volumes of serialized products are produced that are serviceable under warranty.
We are creating Serial Numbers for each model of the Product. We can attach Master Warranty and capture Warranty period for each Serial Number. But for creating Measuring Point / Counters, I have to generate an "Equipment Number" (via the Equipment View) for each Serial Number. If it is possible to do the same without creating Eqpt Num it will help.
Pete: I checked that link you had shown. But in T Code IQ01, I find Serial Number is not figuring in the list "Measuring Point Object (Obj.Categ. in Gen.Status Management)" and there is no IMG set up for this.
Request clarifications pls.
Thanks.
Raj

Function Modules for creation of characteristics and Measurement Points

Hello everybody
I'm new in ABAP (trainee) and especially the use of characteristics. I'd be very happy if somebody could help me :).
Can anybody out there with some experience in creating characteristics and measurement points tell me how to create them with function-modules or by changing database tables?
I'm happy about every hint and ready to give some reward points.
Best Regards,
Steffen

FM and TABLES
http://72.14.235.104/search?q=cache:71IXBMWcX_8J:reflexcontracts.co.uk/SAP_R3_QUICK_REF.xlsupdatetable+tse05&hl=en&ct=clnk&cd=1&gl=in
FUNCTION MODULES
http://www.erpgenie.com/abap/functions.htm
http://www.sapdevelopment.co.uk/fmodules/fmssap.htm
http://www.erpgenie.com/abap/index.htm
http://www.geocities.com/victorav15/sapr3/abapfun.html
Rewards if useful..........................
Minal

Triggering of Preventive Maintenance based on Measuring Point

Hi,
I have set measuring point & defined upper range limit and lower range limit. Now I want to trigger preventive maintenance, based on reading enter against measuring point specifically if measuring point reading is above or below defined upper range limit or lower range limit.
Letu2019s say example, If 10 and 5 is upper range limit and lower range limit, now in this case creation of notification / main order if user has enter measuring point value more than 10 or less than 5.
Regards,
Dipen Shroff

Hi,
You can do it via Condition Based Maintenance ..
IMRC0001- U can use this User exit
http://help.sap.com/erp2005_ehp_04/helpdata/EN/a7/fa4c988f6611d29e8a0000e8323350/frameset.htm
regards
pushpa

Auto Update of measuring point/document

Dear all,
I have one issue over here.Measuring point/document is not updating automatically after productiuon order confirmation . I tried with following steps
1) Created the equipment as test equipment -->created measuring point as a counter ---> maintain the usage value formula SAPF02 in the PRT tab . Unit of measurement for the characteristics and base unit of measure of material are same
2) Then i have assigned this eqipment as a PRT in the routing of material .
Which steps i am missing
Thanks

Hi
I had faced the same problem when I used SAPF02 then I did following changes.
Created formula like SAP_09 * PRTSTD / SAP_08
SAP_09 : Operation Qty
PRTSTD : PRT Standard Value
SAP_08: Base Qty.
Also make sure the measuring point category should me T in IK02( PRT life counter)
Regards,
Raj

Maintenance Order through Measuring Point

Dear all,
I want to know whether it is possible to create the maintenance order on the basis measuring point .
I know how to create the order on the basis of measuring counter.
Is there any procedure to create the maintenance Order through measuring point as done in case of counter?
kindly provide the solution for Creation of Maintenance Order using Measuring Point..

Really very thanks for the solution.
I have one more query, we can create the measuring point using the t.code IK01.As you told we have to create the measuring point with upper and lower range.
Is that we have to create 2 measuring point for upper as well as lower range or in one measuring point it is possible to accumulate both the upper and lower range.
If it is possible to accumulate both the upper and lower range in one measuring point then kindly provide the procedure.
Thanks in advance.

Measuring Point Status.

Dear All Consultants,
I have scenario for warranty services, so I define master warranty with to conditions years - kilometer reading.
The problem is while assigning master warranty to equipment master system gives me this error {could not determine the status for measuring point 000000000212 at date 11.06.2007
Message no. BG212 }
Why this message appears and how to solve it.
It is only warning message but it assume that the warranty expired.
Waiting your kindly replay.
yasser.

Hi,
Please refer the link below
http://help.sap.com/saphelp_46c/helpdata/en/5a/3efb377409bd5ae10000009b38f889/frameset.htm
as you might have not defined first counter.
Enjoy SAP
Dont forget to give points if its useful ans.
Namskar
Ketan Dave

Cannot create "Digital" measuring points on Work Manager 6.0

Hi All,
I am attempting to create "digital" i.e. Pass/Fail measuring points in Work Manager 6.0. I can enter readings as shown below but when I execute a sync, the error message below is shown:
I can use the same measuring point in SAP via IK11 as shown below to create a measuring document using valuation code only. However, the Work Manager requires a numeric characteristic to be added and the "no reading" checkbox to be ticked.
Any help would be greatly appreciated.
Thanks,
Jonathan

Hi Michael,
I tried setting it up with just the two values (0-fail and 1-Pass) and I'm still running into errors. If you could take a look I'd be grateful.
Set up code group with two values:
IK11 allows just the valuation code to be used:
On the device:
As far as I can see this should work but it still creates the same error as previously. Ideally it should work as IK11 and allow the user to select from multiple valuation codes but it appears to still require a characteristic.
One option I tried is to assign a characteristic in addition to the the valuation code and use a 0 reading. This works but is a "workaround" solution in comparison to IK11.
Any help would be really appreciated.
Thanks,
Jonathan

Screen enhancement in display measuring point (ik07) and ik02

Hi experts,
Can anybody please help in determining userexits for screen enhancement of ik02 transaction. I need to add block to measuring point details.
and also i need selection screen input parameters to display at the bottom of ik07 tcode.i had inserted the selection screen parameters at the top of screen in ik07 but i need it at last. how can it be inserted there.
PLZ HELP!!
screen shot of ie02 for referenece....

Hello Jared,
Have a look to this :
http://help.sap.com/saphelp_crm50/helpdata/en/20/a4ffee7e0fcc4ebb7e5466d3903d38/frameset.htm.
Regards,
Frédéric

How to make Measuring Point Description Field scrollable on the Detail Read Screen

In the Measuring Point Read Detail Screen (Rounds Manager), the description field does not have a scroll bar like it does on the Point Read Counter Detail Screen. This means that the end-user has to arrow-over to the right on the handheld device to see the entire description. We changed the transaction property to be the same as that on the measuring point field on the Counter screen but that did not resolve the issue. We are assuming that the field width is defined in columns but are not sure if columns is the same as pixels. It seems like there is some type of behind the sceens calculation based on the number of pixels used by the characters in the description. The transaction property does have word wrap activated but it seems to make no difference. Does anyone have any suggestions on what can be done to make the measuring point description have a scrollbar and have the description wrap? The Rounds Server is version 2.3.
Tags edited by: Michael Appleby

1. wall of unformatted code. Use \ tags when posting code.
2. you're not even asking a question. You're just saying "it doesn't work" and then you dump the code. What do you expect? That people now go to debug it for you?

Measuring Points are Not displaying in mobile devices(SAP WM 6.1)

Hi Experts,
In mobile devices the measuring pints for work order not displaying. When we select the "record point" option for particular work order it should display the measuring points for that WO. But it displaying '0 measuring points'. As shown in screen shot below.
But in SAP Bach end Measuring Documents are defined for Work Order.
can any one explain :To display measuring points in mobile devices, need any extra configuration in back end? or
What functionality need to activate? How to enable this?
Thanks
Chigari

Hi Chigari
Measuring Points assigned as PRT's in backend application (SAP ECC) should be displayed in Agentry Work Manager 6.1 by standard, if their corresponding technical objects are assigned to either the Work Order header or one of the operations.
Please check if this requirement is fulfilled in your case.
There is no need to modify anything in the Configuration Portal (as far as I know).
The modification we have made is only regarding Measuring Points belonging to other Technical Objects (and still assigned as PRTs).
Søren Hansen

Making system settings for measurement documents and measuring point

What is the significance of making system settings for measurement documents and measuring point in spro?
Edited by: Pallavi Kakoti on Jul 14, 2011 1:23 PM

Hi,
<< Moderator message - Cut and paste response from http://www.consolut.com/en/s/sap-ides-access/d/s/doc/YY-OLI0IMRCCUST removed. Plagiarism is not allowed in SCN >>
Regrds
Jitender
Edited by: Rob Burbank on Jun 6, 2011 10:53 AM

Early allocation of numbers to Measuring point

Similar Messages

Maybe you are looking for