Emergency: I can't set encapsulation dot1q on subinterface on 1721

pls help me
i have this problelm with 1721 ,i changed IOS many time but result is same ,if we want to enableISL or Vlan on a 1721 Router:
first we have to define a subinterface,then we have to define the encapculat
ion ,in this case we can make the subinterface but not the encapsulation,the
procedure is as follow:
Router#configur Terminal
Router(config)#ip routing
Router(config)#interface fastethernet 0.10
Router(config-subif)#Encapsulation
here we have to define the "dot1q" encapsulation but the command is not avai
lable the router said
it is unrecognized command)
I upgrade the 1721 with c1700-sy7-mz.123-14.T3.bin image ( ip plus )ios
but the problem exists yet.'
pls reply me as soon as possible
thanks

If you are running IP Plus, you might be running into the following hardware issue.
http://www.cisco.com/cgi-bin/bugtool/onebug.pl?bugid=CSCsa70023
Open a TAC case and get an RMA.

Similar Messages

Can't set encapsulation on Sub-Interaces - 2621 Router

I am studying for my CCNA, playing around with a few of the dirfferent concepts with my hardware. I am trying to setup a router on a stick configuration using a 2600 router and a 2900 catalyst switch.
I have the FastEthernet 0/1 port plugged into Fa0/1 on the switch. The switch has three vlans setup with a client on each vlan
I have set the port on the switch as follows:
Switch(config-if)#switchport mode Trunk
Switch(config-if)#switchport trunk native vlan 1
Switch(config-if)#switchport trunk encapsulation isl
When I try to set the router, I get this:
rt01(config)#int fa0/1
rt01(config-if)#no ip add
rt01(config-if)#exit
rt01(config)#int fa0/1.1
rt01(config-subif)#encapsulation isl
^
% Invalid input detected at '^' marker.
I cannot set the encapsulation on the sub interface, ISL or dot1q - it doesn't recognize the "encapsulation command" command at all.
My show version is below. I can't confirm one way or another if this image supports IP Plus (which I've been told may be the problem), but based on the message I get when trying to set the IP address on the subif I would think it does..?
My router sh ver shows:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(6), RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 11-Feb-04 19:24 by kellythw
Image text-base: 0x80008098, data-base: 0x80C83E28
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
rt01 uptime is 1 day, 51 minutes
System returned to ROM by reload
System image file is "flash:c2600-i-mz.123-6.bin"
cisco 2621 (MPC860) processor (revision 0x200) with 61440K/4096K bytes of memory
Processor board ID JAD050309VG (2886660437)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102

Hi
c2600-i-mz.123-6.bin is the IP (not IP Plus) version of software. This doesn't support dot1q or ISL trunks.
The IP Plus would be required for this feature (image name for the plus equivalent of your image would be c2600-is-mz.12.3-6.bin)
Regards
Aaron
Please rate helpful posts...

Encapsulation dot1Q

como puedo poner encapsulation dot1Q para la VLAN 1 en un router 1700

Roughly translated (I think)...
"can I put encapsulation dot1Q for the VLAN 1 in a router 1700"
http://www.cisco.com/en/US/docs/routers/access/1700/1701/software/configuration/guide/vlans.html

Encapsulation dot1q is not working?, 2600 Cisco router

     I am trying to config a 2620 Cisco router to perform subintreface (F0/0.1) for Vlan Trunk Protocol, however when I try to configure the encapsulation dot1q, I continue to receive error massage with ^ symbol below the 'c' See below, the platform version is a 12.3(26) which should be acceptable to perform an (encapsulation dot1q). The Ethernet is a fast-Ethernet 10/100 port. I also try the ISL, I receive the same massage.
Can anyone suggest what could be the problem!!
Thank you all!!!!!
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no ip address
Router(config-if)#no shutdown
Router(config-if)#int f0/0.1
Router(config-subif)#encapsulation dot1q 1
^ % Invalid input detected at '^' marker. Router(config-subif)#
==================================================================================================== Router#show version
Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by cisco Systems, Inc. Compiled Mon 17-Mar-08 15:23 by dchih ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Router uptime is 5 minutes System returned to ROM by power-on System image file is "flash:c2600-i-mz.123-26.bin" cisco 2620 (MPC860) processor (revision 0x600) with 28672K/4096K bytes of memory . Processor board ID JAD05440GAN (1508240486) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#
==================================================================================================
Router#sh flash
System flash directory:
File Length Name/status
1 7754580 c2600-i-mz.123-26.bin [7754644 bytes used, 633960 available, 8388604 total]
8192K bytes of processor board System flash (Read/Write)
Router#

jesse rodriguez wrote:I am connected through the console, Here are the output.Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)# Router(config)#int f0/0 Router(config-if)#no ip address Router(config-if)#no shutdown Router(config-if)# *Mar 1 00:01:36.891: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t o up Router(config-if)# Router(config-if)#int f0/0.1Router(config-subif)#enc ? % Unrecognized commandRouter(config-subif)#en? % Unrecognized command Router(config-subif)#en ? % Unrecognized command Router(config-subif)#enJesse
It's possible your feature set it not good enough to run trunking.
Trunking apparently requires a minimum of the IP PLUS feature set according to this document
http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a00800949fd.shtml
table 2 shows a minimum IOS of 12.0(1)T and IPPLUS/IPPLUS on the 2620 - so your IOS revision is OK, but maybe your feature set is not.
You can figure which feature set you have by going here
http://tools.cisco.com/ITDIT/CFN/Dispatch?act=rlsSelect&task=search&searchby=image
and entering your image name (assuming it's not been stuffed with) which you can find by doing "show flash" or "dir"
If you don;t have the right feature set, then you're out of luck unless you can upgrade/change the IOS image the router is booting with.
Cheers.

2960 will not allow "switchport trunk encapsulation dot1q" CLI

I have a Cisco 2960 switch that is not allowing me to setup switchport trunk encapsulation dot1q on a trunking interface.
The show capabilities shows that the interface can use 802.1q, but when I try to CLI the command the work encapsulation is not an option.
Please advise with a solution.
Thanks, S
Model - WS-C2960G-24TC-L
SW Version - 12.2(44)SE6
SW Image - C2960-LANBASEK9-M
S1#
S1#sh int gi0/23 capabilities
GigabitEthernet0/23
Model:                 WS-C2960G-24TC-L
Type:                 1000BaseLX SFP
Speed:                 1000
Duplex:               full
Trunk encap. type:     802.1Q
Trunk mode:           on,off,desirable,nonegotiate
Channel:               yes
Broadcast suppression: percentage(0-100)
Flowcontrol:           rx-(off,on,desired),tx-(none)
Fast Start:           yes
QoS scheduling:       rx-(not configurable on per port basis),
                         tx-(4q3t) (3t: Two configurable values and one fixed.)
CoS rewrite:           yes
ToS rewrite:           yes
UDLD:                 yes
Inline power:         no
SPAN:                 source/destination
PortSecure:           yes
Dot1x:                yes
Multiple Media Types: rj45, sfp, auto-select
S1#
S1#
S1#
S1(config-if)#switchport ?
access         Set access mode characteristics of the interface
backup         Set backup for the interface
block         Disable forwarding of unknown uni/multi cast addresses
host           Set port host
mode           Set trunking mode of the interface
nonegotiate   Device will not engage in negotiation protocol on this
                 interface
port-security Security related command
priority       Set appliance 802.1p priority
protected     Configure an interface to be a protected port
trunk         Set trunking characteristics of the interface
voice         Voice appliance attributes
S1#
S1#
S1#
S1(config-if)#switchport trunk ?
allowed Set allowed VLAN characteristics when interface is in trunking mode
native   Set trunking native characteristics when interface is in trunking
           mode
pruning Set pruning VLAN characteristics when interface is in trunking mode
S1#
S1#
S1#

Newer devices don't support ISL so you can only run 802.1Q. That means that there is no need for an encapsulation command because only one encapsulation is supported. If the device had support for ISL then you would also have that command.
Daniel Dib
CCIE #37149
Please rate helpful posts.

How can I set a path for a new AD-User in this Switch example?

Hi,
I am nearing the end of my script that creates a new ad user, adds them to a set of groups, and moves them to their correct ou.
The problem I have is that I cant work out how to move them to the OU.
eg.
Step 1. In my function I have completed the part that creates the user, and I have used the -passthru parameter to return the new user object into a variable called $obj.
Step 2. I have created a switch that accepts a department variable, and adds the user to the corresponding groups.
Step 3. Finally I want the user to be created in an OU that is relevant to their job role. If possible in the same switch as above.
Here is the switch :
Switch($dept)
Finance {$FinanceGroups = @("Finance","Users");ForEach($group in $FinanceGroups){Add-ADGroupMember -Identity $group -Members $Obj}}
Sales {$SalesGroups = @("Sales","Users");ForEach($group in $SalesGroups){Add-ADGroupMember -Identity $group -Members $Obj}}
Support {$SupportGroups = @("Support","Users");ForEach($group in $SupportGroups){Add-ADGroupMember -Identity $group -Members $Obj}}
I was trying to do it like this.
Finance{$FinanceGroups=@("Finance","VPN_Users");ForEach($groupin$FinanceGroups){Add-ADGroupMember-Identity$group-Members$Obj}{$Obj.Path ="OU=Staff,OU=Accounts,OU=Resources,DC=homenet,DC=com"}}
But it doesn't seem to work, and I think the problem could be that the new user object returned by the -passthru parameter is read only. So I can't set it's parameters.
Can you think of a way to do it?
Thanks

I would re-write this function as follows:
Function New-User {
[CmdletBinding(SupportsShouldProcess=$true, ConfirmImpact='High')]
Param(
[Parameter(Mandatory=$true,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=0)]
[String]$fname,
[Parameter(Mandatory=$true,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=1)]
[String]$sname,
[Parameter(Mandatory=$true,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=2)]
[ValidateSet("Milan","London","tokyo")]
[String]$site,
[Parameter(Mandatory=$true,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=3)]
[ValidateSet("Finance","Sales","Support")]
[String]$dept,
[Parameter(Mandatory=$false,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=4)]
[String]$baseOU = "OU=Accounts,OU=Resources,DC=homenet,DC=com",
[Parameter(Mandatory=$false,
ValueFromPipeLine=$true,
ValueFromPipeLineByPropertyName=$true,
Position=5)]
[String]$tempPass = "Temp-pass1"
Write-Verbose "Creating user '$fname $sname' in OU 'OU=$dept,$baseOU'"
$objUser = New-ADUser -name "$fname $sname" `
-GivenName $fname `
-Surname $sname `
-DisplayName "$fname $sname" `
-SamAccountName "$fname.$sname" `
-AccountPassword ($tempPass | ConvertTo-SecureString -AsPlainText -Force ) `
-ChangePasswordAtLogon:$true `
-Path "OU=$dept,$baseOU" `
-PassThru
$Groups = @("All_$site","Users","$dept")
Write-Verbose "Adding user '$fname $sname' to groups '$($Groups -join ', ')'"
$Groups | % { Add-ADGroupMember -Identity $_ -Members $objUser.DistinguishedName }
Write-Verbose "Enabling user account '$fname $sname'"
Enable-ADAccount -Identity $objUser.DistinguishedName
<#
Examples
New-User -fname "Sam" -sname "test" -site Milan -dept Finance -Verbose
#>
Notice:
Function name: follows verb-noun format - best practice
$obj variable renamed to $objUser - using variable name that reflects its content
Use of CmdLetBinding[] and confirm impact as high since you're writing to AD
Use of ValidationSet to minimize parameter input errors
Parameterized baseOU, and TempPass
Added requirement to change password at first logon
Enabling the account at the end
You should wrap each of the 3 steps in a try-catch block. Check for things like user already exists or not, group exists r not, OU exists or not..
Sam Boutros, Senior Consultant, Software Logic, KOP, PA http://superwidgets.wordpress.com (Please take a moment to Vote as Helpful and/or Mark as Answer, where applicable) _________________________________________________________________________________
Powershell: Learn it before it's an emergency http://technet.microsoft.com/en-us/scriptcenter/powershell.aspx http://technet.microsoft.com/en-us/scriptcenter/dd793612.aspx

Can I set individual alerts (tones) for each calendar events/ reminders

Can I set individual alerts (tones) for each calendar events/ reminders

Thanks On my phone, these are the options under Menu>Settings & Tools>Sound Settings>Alert Sounds: 1. TXT Message 2. Multimedia Message 3. Voicemail 4. Emergency Tone 5. Missed Call . And under Service Alerts: 1. ERI 2. Minute Beep 3. Call Connect 4. Charge Complete 5. Software Update. So nothing there for the calendar. And options from the calendar that I can see are Add (here you can change the tone for one event or recurring event, but not set a default tone for the event alarm), View (gives you the options of viewing an existing event in more detail, adding a new one, and the same choices from the Options list on the first screen where you are viewing the entire month), and Options (1. lets you view weekly/monthly, 2. Go To Today 3. Go To Date 4. Search 5. Erase All 6. Erase All Old 7. Send. So as far as I can see, there's no way to do it. I have been through all the Settings and Tools menus... and the Events menu. But...I have just discovered that if I delete ALL my alarms and change the Ringtone for the first alarm I set, that ringtone becomes the default ringtone. I will try deleting ALL my events and starting fresh with a new tone and see if that works!

Encapsulation dot1q any second any on me3600x

Hi,
we recieve a number of downstream hand-offs that are delivered as SVID/CVID ccts. There are mixture of data, and VOIP subscribers, the only way to tell the different type of subscribers is that the all voip services are marked as cos 4. All data subscribers are marked cos 0. I have no control over the SVID/CVID mix, and there is no "pattern" so I cannot enter ranges.
I am wanting to deliver each subscriber type to a different bridge-domain then use xconnect to forward these so ultimately i have one bridge-domain with VOIP services, and one with data services.
on the me3600x I tried the following:
interface GigabitEthernet0/4
switchport trunk allowed vlan none
switchport mode trunk
service instance 950 ethernet
encapsulation dot1q 1-4096 secondary 1-4096
bridge-domain 950
service instance 951 ethernet
encapsulation dot1q 1-4096 secondary 1-4096 cos 4
bridge-domain 951
This seemed to work with cos 4 traffic being sent to a differnet bridge-domain than other traffic, however when i try to apply this config to more than 4 interfaces (8 bridge-domain members) i get a "command rejected" error when i enter the "encapsulation dot1q" command. "Encapsulation deafult" is still accepted though.
can any one explain to me why there is this limitation, or if there is any way around it, or any other way to do what i am trying to do?
ta.

Hi Mike,
I replicated your setup in the lab and it appears the problematic line causing this interesting limitation is the “encapsulation dot1q any second-dot1q any” under the “service instance 950”
Since you are not really interested in the second tag value you can leave it out of the equation using just “encapsulation dot1q any” –to match any frame (not matching any more specific service instance rules) with at least one 802.1q tag or you can use “encapsulation default” –to match any frame (not matching any more specific service instance rules)
interface GigabitEthernet0/1
switchport trunk allowed vlan none
switchport mode trunk
service instance 950 ethernet
encapsulation dot1q any
bridge-domain 950
service instance 951 ethernet
encapsulation dot1q any second-dot1q any cos 4
bridge-domain 951
c36cx#sh bridge-domain 951
Bridge-domain 951 (6 ports in all)
State: UP                   Mac learning: Enabled
Maximum address limit: 10000
   GigabitEthernet0/1 service instance 951
   GigabitEthernet0/2 service instance 951
   GigabitEthernet0/3 service instance 951
   GigabitEthernet0/4 service instance 951
   GigabitEthernet0/5 service instance 951
   GigabitEthernet0/6 service instance 951
adam

Why I can't set exp bit ?

policy-map match
class exp_0
class exp_1
class exp_2
class exp_3
class exp_4
class exp_5
class exp_6
class exp_7
class-map match-all exp_2
match mpls experimental topmost 2
class-map match-all exp_3
match mpls experimental topmost 3
class-map match-all exp_0
match mpls experimental topmost 0
class-map match-all exp_1
match mpls experimental topmost 1
class-map match-all exp_6
match mpls experimental topmost 6
class-map match-all exp_7
match mpls experimental topmost 7
class-map match-all exp_4
match mpls experimental topmost 4
class-map match-all exp_5
match mpls experimental topmost 5
policy-map L3VPN_multigold_in_100m
class class-default
police cir 100000000 conform-action transmit exceed-action drop
service-policy L3VPN_mutigold_in_Child
policy-map L3VPN_mutigold_in_Child
class realtime
police rate percent 50 conform-action set-mpls-exp-imposition-transmit 4 exceed-action drop
class business_data
police rate percent 25 conform-action set-mpls-exp-imposition-transmit 4 exceed-action drop
class class-default
police rate percent 25 conform-action set-mpls-exp-imposition-transmit 4 exceed-action transmit
class-map match-any realtime
match dscp ef
match dscp cs5
match dscp cs6
match dscp cs7
match dscp af41
class-map match-any business_data
match dscp af31
match dscp cs3
match dscp cs2
match dscp af21
interface TenGigabitEthernet2/1
ip arp inspection limit none
no ip address
load-interval 30
service-policy input L3VPN_multigold_in_100m
service instance 10 ethernet
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
bridge-domain 10
interface Vlan10
ip vrf forwarding l3vpn-mqos
ip address 192.168.1.1 255.255.255.0
interface TenGigabitEthernet2/2
mtu 9000
ip address 192.168.11.2 255.255.255.0
ip router isis
load-interval 30
mpls ip
mpls traffic-eng tunnels
clns mtu 1497
isis circuit-type level-2-only
isis network point-to-point
isis metric 100 level-2
service-policy output match
ip rsvp bandwidth 1410066
pe1#sho policy-map int | inc Ten|Cla|pac
TenGigabitEthernet2/1
Class-map: class-default (match-any)
2465961 packets, 2579395206 bytes
conformed 1264280 packets, 1322436880 bytes; actions:
exceeded 300382 packets, 314199572 bytes; actions:
Class-map: realtime (match-any)
1232980 packets, 1289697080 bytes
conformed 632139 packets, 661217394 bytes; actions:
exceeded 600767 packets, 628402282 bytes; actions:
Class-map: business_data (match-any)
616491 packets, 644849586 bytes
conformed 316070 packets, 330609220 bytes; actions:
exceeded 300384 packets, 314201664 bytes; actions:
Class-map: class-default (match-any)
616490 packets, 644848540 bytes
conformed 316069 packets, 330608174 bytes; actions:
exceeded 300384 packets, 314201664 bytes; actions:
TenGigabitEthernet2/2
Class-map: exp_0 (match-all)
471098 packets, 494652900 bytes
Class-map: exp_1 (match-all)
0 packets, 0 bytes
Class-map: exp_2 (match-all)
245559 packets, 257836950 bytes
Class-map: exp_3 (match-all)
0 packets, 0 bytes
Class-map: exp_4 (match-all)
0 packets, 0 bytes
Class-map: exp_5 (match-all)
554263 packets, 581976150 bytes
Class-map: exp_6 (match-all)
0 packets, 0 bytes
Class-map: exp_7 (match-all)
0 packets, 0 bytes
Class-map: class-default (match-any)
0 packets, 0 bytes
SW: (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.3(1)S
HW: 76-ES+XT-2TG3CXL
Thank you very much.

Now I changed to:
policy-map L3VPN_mutigold_in_Child
class realtime
police rate percent 50 conform-action set-mpls-exp-topmost-transmit 4 exceed-action drop
class business_data
police rate percent 25 conform-action set-mpls-exp-imposition-transmit 4 exceed-action drop
class class-default
police rate percent 25 conform-action set-mpls-exp-imposition-transmit 4 exceed-action transmit
Its not changed.
pe1# pe1#sho policy-map int | inc Cla|pac
    Class-map: class-default (match-any)
      11721193 packets, 12002501632 bytes
        conformed 6001573 packets, 6145610752 bytes; actions:
        exceeded 0 packets, 0 bytes; actions:
        Class-map: realtime (match-any)
          11721193 packets, 12002501632 bytes
            conformed 6001573 packets, 6145610752 bytes; actions:
            exceeded 5719822 packets, 5857097728 bytes; actions:
        Class-map: business_data (match-any)
          0 packets, 0 bytes
            conformed 0 packets, 0 bytes; actions:
            exceeded 0 packets, 0 bytes; actions:
        Class-map: class-default (match-any)
          0 packets, 0 bytes
            conformed 0 packets, 0 bytes; actions:
            exceeded 0 packets, 0 bytes; actions:
    Class-map: exp_0 (match-all)
      0 packets, 0 bytes
    Class-map: exp_1 (match-all)
      0 packets, 0 bytes
    Class-map: exp_2 (match-all)
      0 packets, 0 bytes
    Class-map: exp_3 (match-all)
      0 packets, 0 bytes
    Class-map: exp_4 (match-all)
      0 packets, 0 bytes
    Class-map: exp_5 (match-all)
      0 packets, 0 bytes
    Class-map: exp_6 (match-all)
      0 packets, 0 bytes
    Class-map: exp_7 (match-all)
      0 packets, 0 bytes
    Class-map: class-default (match-any)
      0 packets, 0 bytes
Thank you very much.

Switchport access vlan Vs encapsulation dot1Q ?

Hi All,
Could some one explain the difference between encapsulation dot1Q & the switchport access vlan ???

The command "switchport access VLAN" is a command to specify the one-and-only-one VLAN you want the switch port to carry. By default, an access port will always carry VLAN 1. This is the reason why you will never see the command "switchport access vlan 1". You cannot have an access port carry more than one VLAN (except when you allow voice VLAN).
If you want to have two or more VLANs per a single switchport, then you need to enable Trunking. Therefore the command "encapsulation dot1q" is one of the command to enable Trunking. This command specifies which of the two Trunking protocols to use: IEEE's 802.1q or Cisco's ISL.
Take note that without the command "switchport mode trunk" the interface is still an access port. Not all Catalyst switch will accept the command "switchport encapsulation dot1q". This is because the switch will ONLY accept 802.1q encapsulation so there's no need for this command. All Catalyst 2K (except 2924XL) and some legacy 4000/4500 line cards support only 802.1q encapsulation. All others will support either 802.1q or ISL. You will never find a Catalyst switch that can support BOTH 802.1q and ISL.

Applying "route-map" in interfaces with encapsulation dot1q

Hello,
I would like to ask you if there were some trouble in applying route-maps in a interface and its subinterfaces, as it is shown:
interface GigabitEthernet0/2
ip address 11.0.9.26 255.255.255.252
ip policy route-map GestionRadios
interface GigabitEthernet0/2.11
encapsulation dot1Q 11
ip address 11.0.9.18 255.255.255.252
ip policy route-map RedOperativaA
interface GigabitEthernet0/2.12
encapsulation dot1Q 12
ip address 11.0.9.22 255.255.255.252
ip policy route-map RedOperativaB
I am not sure if it is correct totally. Besides I get this informacion doing "show ip policy" and it seems to be right.
Router#show ip policy
Interface      Route map
Gi0/2          GestionRadios
Gi0/2.11       RedOperativaA
Gi0/2.12       RedOperativaB
I would be very grateful for your help.
Thanks in advance
Regards,
Sandro

Sandro
We do not have much to work with in your post so giving you really good answers is difficult. You do not tell us what type of device this is (I assume probably a router, but perhaps it is a layer 3 switch?) or what version of code it is running. These things make a difference sometimes in what is supported or is not supported. But since you get output in show ip policy then I assume that the device does support configuration of this feature.
You show us the configuration of the interfaces but not the configuration of the route maps or the access lists which the route maps probably use. So we can not form an opinion of the validity of the route maps or the access lists.
And you do not tell us whether the Policy Based Routing is working or not (and in fact you do not tell us for sure that you are doing PBR - though that is generally what route maps on the interfaces are doing) so we are not clear whether there is a problem here or not.
But based on what you show us in this post I do not see any particular problems with the route maps and the way that you have applied them to interfaces (assuming that your goal is really to do PBR).
HTH
Rick

I forgot the administrator password for my mac and cant set a new one without it how can i set a new one

i forgot the administrator password for my mac and cant set a new one without it how can i set a new one

Reset Password 10.7, 10.8...
http://reviews.cnet.com/8301-13727_7-20087723-263/how-to-run-the-password-reset- utility-in-os-x-10.7-lion/

My wife and I share the iPad. Can we set up separate accounts to log in (like on our Mac)?

My wife and I share the iPad. Can we set up separate accounts to log in (like on our Mac)?

Good question, but I'm 99.9% certain the answer is "no". Here are some considerations:
Think of the heritage of iOS. It really started with iPhones and maybe iPods. These devices cost a whole lot less than a Mac. They are generally not thought of as shared (with exceptions, of course, as is true for you).
Think of the backup process. i-devices typically sync with one iTunes on one computer. How would an i-device with multiple users enstantiate this?
Anyway, all this is to say I'm convinced you cannot do what you're inquiring about.

Is there a way that iTunes can act as a Radio Alarm Clock? I have found the radio station I enjoy listening to in the iTunes Radio List. Is there anyway iTunes (and my Mac) can be set to come-on and start playing that Radio Station from Sleep mode at spec

Is there a way that iTunes can act as a Radio Alarm Clock?
I have found the radio station I enjoy listening to in the iTunes Radio List. Is there anyway iTunes (and my Mac) can be set to come-on from Sleep mode and start playing that Radio Station at specific times of the day?
Any App or plug-in that does that?
Many thanks
Kevin

Turning your Mac into a clock radio.
1. In iTunes create a playlist that contains just the radio station you want to wake up to.
2. Export the playlist (as .m3u works well). Get Info on your playlist file and look at the Open With entry to make sure it points to iTunes, VLC or some other app that will stream your station.
3. In iCal create an event entry at the time you want to wake up.
4. Right (or Control) click on your wakeup event and select Get Info.
5. For "alarm" select Open File.
6. Now under Open File there will be a place to add the file to open. It will probably be some default entry (like iCal). Click on it will allow you to select "other." Then use the file dialog to select your playlist file.
Your Mac will wake you up at the appointed time. You don't need to keep iCal running. If you want to put you Mac to sleep for the night then there is one more thing you need to do. Open System Preferences to Energy Saver and click on the Schedule button. Check Start up or wake and set the wake up time to slightly before your iCal alarm time.
Dan

Can you set a "default" web page in a KM folder?

Hi there,
I've been playing around with using Adobe Contribute to edit web pages in a CM Repository. It was easy to create a CM repository, put some web pages and supporting CSS, images etc. in there, and create a KM navigation iView that displays the default page. Setting up Adobe Contribute to edit those pages via a WebDAV protocol was simple too, and to be honest I find the Contribute interface and functionality easier to use (particularly from the average end user's point of view) and implement than the Portal's built-in HTML editor, or the Web Page Composer.
But then I ran into a snag. In order to be able to "administer" the site with Contribute (or Dreamweaver), it creates an _mm folder and puts a "guard" page in it. The guard page is a file which would be returned to the browser when it tries to access a folder. In a normal website that would be a "default" page (e..g index.htm, default.htm etc.), but in the Portal there doesn't seem to be a way to have one. I believe that's why if you try to access a folder through a browser you get:
"The folder you are looking for has no displayable content.
You can try one of the following:
Access the folder using the Navigation user interface.
Access the folder as a Web folder. Your operating system and browser dictate whether or not this will work."
That's what happens if I use something like http://<host name>:<port number>/irj/go/km/docs/<repository prefix>/<folder name>/ as a URL, though http://<host name>:<port number>/irj/go/km/docs/<repository prefix>/<folder name>/default.htm works just fine (as you would expect). And I can retrieve a fake "guard" page using http://<host name>:<port number>/irj/go/km/docs/<repository prefix>/<folder name>/_mm/default.htm
An Adobe technote confirms this as problem - [Guard Page not found|http://go.adobe.com/kb/ts_f3675780_en-us]. Does any one know if a default page can be set in a CM repository.
Regards,
Tom

I don't think you can.
What is possible is to set content on the folder resource itself; that would be returned instead of the page you mentioned.

Emergency: I can't set encapsulation dot1q on subinterface on 1721

Similar Messages

Maybe you are looking for