Error -1074395395 occurred at IMAQ Match Color Pattern after merge programs

Dear all
I  have 2 separate programs that use same source image (red01a1.jpg). The first find location of color particles (color location 01.vi) and second find location of particles after threshold  color image (particle location 01.vi).  Both of them run good.  
But when  2 programs were merged  into one program (color sorter 01i.vi), that happened error . The error message is “Error -1074395395 occurred at IMAQ Match Color Pattern”. How can I fix it ?
Thanks  
Solved!
Go to Solution.
Attachments:
color sorter 01i.vi ‏126 KB
Color -particle location.zip ‏86 KB
red01a1.zip ‏86 KB

Hi Xuan
Check it out the attached vi
Sasi.
Certified LabVIEW Associate Developer
If you can DREAM it, You can DO it - Walt Disney
Attachments:
color sorter 01i.vi ‏120 KB

Similar Messages

  • Error -1074397038 occurred at IMAQ Start.vi for 64bit Labview 2011 SP1, Win7

    Hello,
    I am using a MC1362 camera from Mikrotron with a PCIe1433 framegrabber. I was using it with windows XP, 32 bit, labview 2010 SP1 32 bit, it was working perfectly fine. I just switch to windows 7 with labview 2011 SP1 64bit, and it is not working anymore with my custom routine in labview, though it works with MAX and camera file generator and I use the same camera file.
    When I run my routine, I have this error message:
    Error -1074397038 occurred at IMAQ Start.vi
    Possible reason(s):
    NI-IMAQ:  The requested serial termination string was not found in the returned buffer.
    Then, If I try to run the camera with MAX, it doesn't work anymore, I have to reboot the camera, and put it in the right mode with the Mikrotron control tool to obtain an image.
    I have seen similar issue on a Basler camera on the forum, and it has been solved by using a camera file to set the different parameters. There is no camera file complete to set all the parameters of the camera, so I had to program them in serial to drive the camera with my Labview routine.
    Could you help me to solve this issue please?
    Thanks
    Bests
    David Dulin

    This forum post is already handled --> SR 1154262.
    Kind regards,
    Corné Westeneng
    Applications Engineer
    NI-Netherlands

  • Error -1074395975 occurred at IMAQ AVI Read Frame DirectX has timed out readin

    When i run the "Read AVI Example" on every kind of AVI file, I get the error:
    Error -1074395975 occurred at IMAQ AVI Read Frame DirectX has timed out reading or writing the AVI file. When closing an AVI file, try adding an additional delay. When reading an AVI file, try reducing CPU and disk load.

    The forums search gives two threads talking about this error:
    http://forums.ni.com/ni/board/message?board.id=170&message.id=392042&requireLogin=False
    http://forums.ni.com/ni/board/message?board.id=170&requireLogin=False&thread.id=195832
    Did you allready had a look at them?

  • IMAQ Learn Color Pattern hangs

    Running Labview 2012 SP1 and Vision Development Module 12.1.0.  IMAQ Learn Color Pattern appears to hang if you call it without defining an ROI.  See attached program - it is intended that user define an ROI then click "Define ROI" button.  If you click the button without first defining an ROI, Learn Color Pattern hangs for over a minute then returns OK.  I found a workaround for this by checking for a valid ROI before calling the VI, but it seems unusual behavior for Labview.
    Attachments:
    learn color pattern hangs.zip ‏74 KB

    Hi Bucky,
    I took a look at your program, and if I run it with highlight execution, I can see that the program is waiting on the Learn Color Pattern function as you said. However, I don't think this would be considered hanging. The front panel is still responsive, and if you add other processes to the program, they continue running while the Learn Color Pattern function is executing.
    I believe the long execution time is because when no ROI is specified, the function acts on the entire image, which takes a fair amount of time. You can confirm this by selecting a ROI that is almost the size of the entire image. The program takes a similarly long time to execute. The best way to cut down on execution time would be to select a smaller ROI. I hope this helps!
    David S.

  • Error -1074397150 occurred at IMAQ Snap.vi

    Hi.
    (Sorry if my English is wrong )
    I want to snap a picture - from a camera that was designed in my lab - and save it in a BMP file.
    I use the "IMAQ PCI-1428" to accomplish this task and the "HL snap&save to BMP.vi".
    But, as I try to run the VI I'm getting this error - "Error -1074397150 occurred at IMAQ Snap.vi", afterward I'm getting
    another massage - "ERROR(DMA Timeout): The system is unable to capture all of the incoming video data....".
    What should I do, to resolve this problem?
    ThanX.

    Hi elbit,
    Here is a link to Error
    Codes with NI-IMAQ.  You error is
    addressed there and that information may be helpful to you.
    I noticed you were using the PCI-1428 framegrabber card.  This card supports Camera Link cameras.  In order to tell the PCI-1428 how to
    communicate with the camera, the NI-IMAQ driver uses a camera file that
    contains camera specific information for configuration.  You will need to have a properly configured
    camera file for you camera that you have created.
    NI has a large number of camera files that are created and
    certified to support popular industrial grade cameras.  In cases where a custom camera file is needed,
    NI provides the NI-Camera
    File Generator as a utility for camera file creation.  Keep in mind that custom camera files are not
    supported by National Instruments Applications Engineers.
    Good luck with your camera design.  Please let us know if you have any further
    questions or concerns.
    Regards,
    Luke H

  • Error -1074396116 occurred at IMAQ CalibrationTargetToPoints

    Error -1074396116 occurred at IMAQ CalibrationTargetToPoints, So there any one to solve this problem and thank you.

    there is the VI and the picture of device. SO i need to calculate the dimension and thank you
    Attachments:
    Calibration.vi ‏77 KB
    Capture.PNG ‏27 KB

  • Error - 1074397153 occurred at IMAQ Grab Setup.vi

    The sensor we are using is Goodrich SU640KTSX. I can run SUI image Analysis 3.1 software, Measurement & Automation software, and MATLAB code on an XP machine with no errors when grabbing images. We are tying to build a newer PC;
    Dell T7500 with Intel xeon CPU x5650 @ 2.67GHz 
    Memory; 12GB
    OS Win7  64-bit
    Camlink card is NI PCIe-1430
    Nvidia QUADRO 4000
    The error we get is "Error -1074397153 occurred at IMAQ Grab Setup.vi / Cannot detect recognizable video source" when using the SUI image Analysis 3.1 software or MATLAB code. When we use the NI-IMAQ i/o 2.3.1- Measurement & Automation  I can snap, grab and record without any error. 
    Any help on this would be great
    Thanks

    Hi,
    Let us know which standard your camera is following (whether it is cameralink or ethernet).
    Check this link for error info: http://digital.ni.com/public.nsf/allkb/3434173630CBC97686256F8000536593.
    If at all it is cameralink camera make sure that you are following proper trigger sequence for your camera. As u are grabbing frames in MAX and not in other acquisition softwares it might be triggering issue or cables problem.

  • My iPod classic, which is 6 years old is corrupted. A message that says ''Connect to iTunes to restore'' keeps on blinking on the screen, But when I connected it to iTunes it says an error has occured and my iPod has hung after i've disconnected it.

    My iPod classic, which is 6 years old is corrupted. A message that says ''Connect to iTunes to restore'' keeps on blinking on the screen, But when I connected it to iTunes it says an error has occured and my iPod has hung after i've disconnected it.

    Hi,
    Time to take your iPod in for service.
    You can make a Genius Bar reservation in advance if you are in the U.S.
    http://www.apple.com/retail/geniusbar/
    Carolyn 

  • Error 1074396024 occur at imaq usb snap.vi

    hallo, ich habe labview 8.0 mit dem vision development modul und
    benutze eine logitech webcam zur bilderfassung. ich habe ein vi
    erstellt das im zeitraum von 1s ständig neue bilder macht und diese mit
    einem referenzbild vergleicht. mein problem ist das so bei ungefähr
    1000 vergleichen eines neuen bildes mit dem referenzbild der fehler
    1074396024 occur at imaq usb snap.vi auftritt und ich aber nicht weiß
    warum.  würde mich freuen wenn mir jemand helfen kann

    Please have a look at this thread which discusses similar issues in detail.
    Best regards,
    Jochen Klier
    National Instruments Germany

  • How to solve Error -1074396080 occurred at IMAQ array to color Image

    Hello,
    I am getting above mentioned error.
    Here I have attached my screen shot of the error.
    Could any one Please guide me how to solve this error.
    I am using Kinesthesia kinect driver which generate U24 Bit RGB Image and I want to convert it in IMAQ Image type, But I am getting mentioned error.
    But when I am not using the vision acquisition and vision assistant then every thing is fine means there is no any error which I have attached in attachment 2.
    Please guide me how to solve this problem.
    Thank you very much.
    Solved!
    Go to Solution.
    Attachments:
    invalid image type.png ‏251 KB
    imaq2.png ‏56 KB

    Thank you very much for quick reply.
    I follow your instruction but it give me still same error.
    here in attachment I have attache screen shot as well Vi so you have a look.
    thank you very much once again for help and time.
    Attachments:
    Unbenannt.png ‏174 KB
    kinect templet.vi ‏137 KB

  • Color change after merging to HDR Pro, going back into Lightroom

    I recently updated Lightroom and now when I "merge to HDR Pro in PS" the photo then comes back into lightroom with highly elevated contrast.  I have set the color options to ProPhotoRGB in Lightroom and Photoshop. and the image looks fine when going from LR to PS, and it looks fine in "preview" after saving the image as a TIFF.  But once that TIFF gets imported back into LR it has all those weird color changes.   I'm not sure what to do, and I never had this problem until I recently updated photoshop and lightroom.  Any help you would be appreciated. thanks!

    The image will look different in PS than in LR. PS uses the embedded preview and LR uses the actual 32 bit image data. You need to apply the LR Develop module Basic panel Tone settings to the 32 bit HDR TIFF.

  • Error imaq color pattern

    hi, I'm trying to do a draft color pattern recognition, but labview gives me this error, I hope you can help me, let the files, thank you very much
    Error -1074395384 occurred at IMAQ Match Color Pattern
    Possible reason(s):
    IMAQ Vision: Invalid color template image.
    Attachments:
    pastillas1.png ‏55 KB
    pastillas2.jpg ‏42 KB
    Parámetros de Búsqueda Color.vi ‏78 KB

    Hello,
    the general idea is:
    Best regards,
    K
    https://decibel.ni.com/content/blogs/kl3m3n
    "Kudos: Users may give one another Kudos on the forums for posts that they found particularly helpful or insightful."

  • Error 1074395626 - IMAQ Learn Geometric Pattern 2

    Hi,
    I am facing this error 1074395626 - IMAQ Learn Geometric Pattern 2, in my VI. I search and did not find much information about it. 
    I also get another error 1074395628 - IMAQ Match Geometric Pattern 2, but I guess fixing the previous one could solve this?
    How can I fix the above errors?

    こんにちは。
    Match Pattern 3 を試して精度がたりないとのことですが、使用しているVI や画像を添付することはできますか。
    そして画像処理のVI は内部で複雑な処理が行われているので、いろいろなパラメータなどを設定する必要があります。
    ですので、画像処理のアルゴリズムをプログラムするときはLabVIEW ですぐさまVI を並べ始めるよりも、
    大抵 LabVIEW Vision 開発モジュールに付属しているVision Assistant というソフトから大まかなアルゴリズム（スクリプト）を作成してから、
    そのスクリプトをLabVIEW のVI に変換します。（Vision Assistant が変換してくれます）
    Vision Assistant を起動するとソリューションウィザードというサンプルがまとめられたものがありますので、
    そちらでテンプレートマッチングなどが使用されているサンプルを活用してみてください。
    そしてヘルプにテンプレートの作成方法やパラメータの設定方法などが記述されているのではないかと。

  • IError -1074395992 occurred at IMAQ ReadFile when processing batch via a vi

    I have built a vi from a visoin assitant file via the automated vi creation under tools in vision assitant. The vi works fine on a single file but then the input control is changed to select an entire directory it crashed with
    Error -1074395992 occurred at IMAQ ReadFile File access denied.
    It reads all the files individually but won't run in the batch mode.
    Attachments:
    vitest.vi ‏164 KB

    Hi Patrick,
    Sorry it's taken so long to get back to you.  The function you are trying to use doesn't actually support reading of many files at a time (batch processing), what you will have to do is extract all of the path names individually and then complete paralel processing on all of the images.  (The image constant that is passed to each of the functions can only store one image at a time)
    I have taken your vi and changed it slightly to allow for this functionality.
    I hope this helps
    AdamB
    Applications Engineering Team Leader | National Instruments | UK & Ireland
    Attachments:
    vitest[1].vi ‏80 KB

  • Receiving a message "an error has occurred" while trying to download mac os x lion. HELP!

    I purchased the update to Mac OS X Lion (10.7) for my MacBook running 10.6.8. When I attempt to download I receive the message "An error has occurred" (see attached screenshot).

    OK, now after a reboot, the purchased items  list is empty... how can I start the download again!?

Maybe you are looking for