Error Adapter Engine

Hi experts,
I have scenario file to RFC asyncronuos. The function RFC have 2 import parameter and 1 parameter export.
I have looked at possible solutions forum, I've seen that can be debugging function rfc for that I must copy it into XI, but this is very laborious, this nest many other functions that are not in Z XI.
In runtime occurs the error:
MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: failed to parse BAPI response due to: com.sap.aii.af.rfc.util.bapi.BapiException: Parameter with name RETURN not found.: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: failed to parse BAPI response due to: com.sap.aii.af.rfc.util.bapi.BapiException: Parameter with name RETURN not found.
very thanks,
regards,

hi,
u r trying file to rfc asych.. but u said that rfc having export parameter.
hence rfc trying to find the return parameter which was not mapped .so u r getting failed to parse BAPI response error.
try to make wraper rfc... rfc having no export parameter.........
regards,
navneet...

Similar Messages

Adapter Engine Red

Hi All,
In Run Time Work Bench, under Component Monitoring, I find that the Adapter Engine is Red in color.
Red LED; Component Status contains an error-Adapter Engine X01
What could be the reason for this error??
Regards
Kartik

check the communication channel monitoring...if any adapter is in error then it status is always red...
even if in the next attempt if interface testing is successful the adapte status will remain RED...
other alternative...inactive the adatper, activate the chage..again activate and chage it..I think then it will show green status..if every thing goes ok with that adapter:)
Thanks
Farooq.

Error in Adapter engine-"No_Spedin"

Hi All,
I have observed the below error in adapter engine today(System error).
JCO.Exception while calling /SEEAG/RELI_XI_EDIINH_FILE in remote system (RfcClient[PEQ_RFC_INBOUND]):com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE: Exception condition "NO_SPEDIN" raised.: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException
The message is going to print Sumfax to SAP ECC.There are no errors in the mapping and the communication channel is also running fine.there was an upgrade in SAp recently after which i observe this error and it didnot exist before.
Can anybody please help me!

Hi Sudha
check Abhishek's Reply may be helpful at this thread for com.sap.aii.af.rfc.afcommunication.RfcAFWException
Re: Error during processing local bean: localejbs/RfcAFBean
also check the The Sender Agreement Interface , it is either missing or not correct in ID
Regards
Abhishek

Error in gettnig logon data for Adapter Engine

Hi,
We have Http > XI > RFC Scenario. We are getting 401 unauthorized error in "CALL ADAPTER" section. From the trace its clear that the logon data for the adapter engine (there is no value for USER in trace) is not getting poulated. We fixed this issue last evening....i think by doing full cache refresh, but this problem propped up again today. Yesterday when this issue was fixed the USER has "PIISUSER" in the trace.
We haven't changed any config settings since yesterday so all the passwords and other config info is same. Not sure what's causing this issue. Below is the trace. Any help will be highly appreciated.
- <Trace level="1" type="B" name="CL_XMS_PLSRV_IE_ADAPTER-ENTER_PLSRV">
<Trace level="3" type="T">Channel for adapter engine: RFC</Trace>
- <Trace level="1" type="B" name="CL_XMS_PLSRV_CALL_XMB-CALL_XMS_HTTP">
<Trace level="2" type="T">return fresh values from cache</Trace>
<Trace level="2" type="T">Get logon data for adapter engine (SAI_AE_DETAILS_GET): af.ppi.dac-sapd1</Trace>
<Trace level="3" type="T">URL = http://dac-sapd1.actv2.com:8007/MessagingSystem/receive/AFW/XI</Trace>
<Trace level="3" type="T">User =</Trace>
<Trace level="3" type="T">Cached = X</Trace>
<Trace level="3" type="T">Creating HTTP-client</Trace>
<Trace level="3" type="T">HTTP-client: creation finished</Trace>
<Trace level="3" type="T">Security: Basic authentication</Trace>
<Trace level="3" type="T">Serializing message object...</Trace>
<Trace level="3" type="System_Error">HTTP-client: error response= <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <html> <head> <title>Error Report</title> <style> td {font-family : Arial, Tahoma, Helvetica, sans-serif; font-size : 14px;} A:link A:visited A:active </style> </head> <body marginwidth="0" marginheight="0" leftmargin="0" topmargin="0" rightmargin="0"> <table width="100%" cellspacing="0" cellpadding="0" border="0" align="left" height="75"> <tr bgcolor="#FFFFFF"> <td align="left" colspan="2" height="48"> 401 &nbsp Unauthorized</td> </tr> <tr bgcolor="#3F73A3"> <td height="23" width="84"><img width=1 height=1 border=0 alt=""></td> <td height="23"><img width=1 height=1 border=0 alt=""></td> <td align="right" height="23">SAP J2EE Engine/7.00 </td> </tr> <tr bgcolor="#9DCDFD"> <td height="4" colspan="3"><img width=1 height=1 border=0 alt=""></td> </tr> </table> <table width="100%" cellspacing="0" cellpadding="0" border="0" align="left" height="75"> <tr bgcolor="#FFFFFF"> <td align="left" colspan="2" height="48"> Authentication did not succeed.</td> </tr> <tr bgcolor="#FFFFFF"> <td align="left" valign="top" height="48"> Details:</td> <td align="left" valign="top" height="48"><pre> No details available</pre></td> </tr> </body> </html></Trace>
<Trace level="3" type="T">HTTP-client: closing...</Trace>
<Trace level="3" type="T">HTTP-client: sending http-request...</Trace>
<Trace level="3" type="T">HTTP-client: request sent</Trace>
<Trace level="3" type="T">HTTP-client: Receiving http-response...</Trace>
<Trace level="3" type="T">HTTP-client: response received</Trace>
<Trace level="3" type="T">HTTP-client: checking status code...</Trace>
<Trace level="3" type="T">HTTP-client: status code = 401</Trace>

Hi,
go to the exchange profile.
there u need to maintain the password for the XIISUSER.
I think u need to restart the J2EE Engine for the changes to take effect.
Regards
Cornelius

J2ee Adapter engine installation error

Hi All,
I am installing XI with NW07. I had an ERP2005 server here with ABAP only. I installed Java Add In to it with usage type PI.
Now I tried to install J2ee adapter engine. It showed if i want to run a new installation or continue the old one.
I tried to install installation of J2ee adapter engine from a new directory.
It is stuck in between. I choose it as a MCOD to existing DB.
I can see a new instance for this in MMC and it is up and running.
But the old java instance is not running. None of the Proceses of Old Java instance (dispatcher, server0 and SDM) are not running. Did I do something wrong?
My JVM_BOOTSTRAP.OUT says this:-
Exception occurred:
com.sap.engine.frame.core.configuration.NameNotFoundException: A configuration with the path "cluster_data/dispatcher/ID4065200" does not exist.
at com.sap.engine.core.configuration.impl.ConfigurationDataCacheAllImpl.getSubConfiguration(ConfigurationDataCacheAllImpl.java:107)
at com.sap.engine.core.configuration.impl.ReadAccessConfiguration.getSubConfiguration(ReadAccessConfiguration.java:715)
at com.sap.engine.bootstrap.Synchronizer.getConfiguration(Synchronizer.java:426)
at com.sap.engine.bootstrap.Synchronizer.getElementType(Synchronizer.java:72)
at com.sap.engine.bootstrap.Bootstrap.initDatabaseConnection(Bootstrap.java:420)
at com.sap.engine.bootstrap.Bootstrap.<init>(Bootstrap.java:144)
at com.sap.engine.bootstrap.Bootstrap.main(Bootstrap.java:814)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at com.sap.engine.offline.OfflineToolStart.main(OfflineToolStart.java:81)
Exception occurred:
com.sap.engine.bootstrap.SynchronizationException: Database initialization failed! Check database properties!
at com.sap.engine.bootstrap.Bootstrap.initDatabaseConnection(Bootstrap.java:422)
at com.sap.engine.bootstrap.Bootstrap.<init>(Bootstrap.java:144)
at com.sap.engine.bootstrap.Bootstrap.main(Bootstrap.java:814)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at com.sap.engine.offline.OfflineToolStart.main(OfflineToolStart.java:81)
== Caused by: ==----
com.sap.engine.bootstrap.SynchronizationException: No such Dialog Instance (ID4065200) in the database! Check database consistency or local Bootstrap properties!
at com.sap.engine.bootstrap.Synchronizer.getElementType(Synchronizer.java:75)
at com.sap.engine.bootstrap.Bootstrap.initDatabaseConnection(Bootstrap.java:420)
at com.sap.engine.bootstrap.Bootstrap.<init>(Bootstrap.java:144)
at com.sap.engine.bootstrap.Bootstrap.main(Bootstrap.java:814)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at com.sap.engine.offline.OfflineToolStart.main(OfflineToolStart.java:81)
Bootstrap module> Problem occurred while performing synchronization.
My dev_jcontrol.b00 shows:-
JControlStartJLaunch: program = C:\usr\sap\IDE\DVEBMGS00\exe\jlaunch.exe
-> arg00 = C:\usr\sap\IDE\DVEBMGS00\exe\jlaunch.exe
-> arg01 = pf=C:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sapides
-> arg02 = -DSAPINFO=IDE_00_bootstrap
-> arg03 = -nodeId=-1
-> arg04 = -file=C:\usr\sap\IDE\DVEBMGS00\j2ee\cluster\instance.properties
-> arg05 = -syncSem=JSTARTUP_WAIT_ON_5284
-> arg06 = -nodeName=bootstrap
-> arg07 = -jvmOutFile=C:\usr\sap\IDE\DVEBMGS00\work\jvm_bootstrap.out
-> arg08 = -stdOutFile=C:\usr\sap\IDE\DVEBMGS00\work\std_bootstrap.out
-> arg09 = -locOutFile=C:\usr\sap\IDE\DVEBMGS00\work\dev_bootstrap
-> arg10 = -mode=BOOTSTRAP
-> arg11 = pf=C:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sapides
-> arg12 = -DSAPSTART=1
-> arg13 = -DCONNECT_PORT=4740
-> arg14 = -DSAPSYSTEM=00
-> arg15 = -DSAPSYSTEMNAME=IDE
-> arg16 = -DSAPMYNAME=sapides_IDE_00
-> arg17 = -DSAPPROFILE=C:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sapides
-> arg18 = -DFRFC_FALLBACK=ON
-> arg19 = -DFRFC_FALLBACK_HOST=localhost
-> lib path = PATH=C:\j2sdk1.4.2_09\jre\bin\server;C:\j2sdk1.4.2_09\jre\bin;F:\oracle\IDE\102\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\j2sdk1.4.2_06\bin;C:\j2sdk1.4.2_06\lib;C:\usr\sap\IDE\SYS\exe\uc\NTI386
-> exe path = PATH=C:\j2sdk1.4.2_09\bin;C:\usr\sap\IDE\DVEBMGS00\j2ee\os_libs;F:\oracle\IDE\102\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\j2sdk1.4.2_06\bin;C:\j2sdk1.4.2_06\lib;C:\usr\sap\IDE\SYS\exe\uc\NTI386
Thr 4232 Tue Sep 16 17:48:04 2008
Thr 4232 *** ERROR => invalid return code of process bootstrap (exitcode = 66) http://jstartxx.c 1642
Thr 4232 JControlExecuteBootstrap: error executing bootstrap node bootstrap (rc = 66)
Thr 4232 JControlCloseProgram: started (exitcode = 66)
Thr 4232 JControlCloseProgram: good bye... (exitcode = 66)
My DEV_BOOTSTRAP.B00 shows:-
Thr 5984 Tue Sep 16 17:48:02 2008
Thr 5984 JHVM_RegisterNatives: registering methods in com.sap.bc.krn.perf.PerfTimes
Thr 5608 Tue Sep 16 17:48:04 2008
Thr 5608 JLaunchIExitJava: exit hook is called (rc = 66)
Thr 5608 **********************************************************************
u2022
o
 ERROR => The Java VM terminated with a non-zero exit code.
 Please see SAP Note 943602 , section 'J2EE Engine exit codes'
 for additional information and trouble shooting.
Thr 5608 JLaunchCloseProgram: good bye (exitcode = 66)
I ran the prerequisite checks before starting the installation.
It shows everything ok except it told me to have a environmental variable as CPIC_MAX_CONV with the value 200 at least. And I did that.
All the other checks were ok.
All are on SAME OS and same machine.
I have J2EE Adapter Engine installation guide, but there is nothing for this in that
In Instance properties file for the old instance it is showing the instance ID which it is not able to find.
In the configtool of both the instances, the instance ID is same under cluster_data and this is of the newer instance
How did the instance ID and data got replaced in the configtool of old instance. I mean the new instance has its new directory or folder.
What Could be the problem?
Did I do anything wrong here?
Kindly help

Hi,
Check out the SNote 997510, " Note 997510 - Troubleshooting
J2EE Engine 6.40/7.0 Bootstrap Issues ".
I hope it will help you to drill more in to the problem
Rgds
Radhakrishna D S

Getting error in the adapter engine when sending a message

Hi,
I'm always getting this error in the adapter engine: Message processing failed. Cause: com.sap.aii.messaging.util.URI$MalformedURIException: no scheme
The comm channel ends up in error because of messages having the above error.
Could someone please help?
Thanks.
Mike

Mike.
Please check this links.
Check your adapter and restarted.
com.sap.aii.messaging.util.URI$MalformedURIException: invalid port number
Re: Prerequisites to setup configure mail scenario.
error in communication channel
Error :Receiver File Channel not Initialized

How to get Alerts mail for adapter engine errors in SAP PI 7.0

Hi Friends,
I configured Alerts in PI 7.0. with the help of t-code u2018ALRTCATDEF and created a new alert catergory.
In container tab i have mentioned all give below elements.
SXMS_MSG_GUID, SXMS_RULE_NAME, SXMS_ERROR_CAT, SXMS_ERROR_CODE, SXMS_FROM_PARTY, SXMS_FROM_SERVICE, SXMS_FROM_NAMESPACE, SXMS_FROM_INTERFACE, SXMS_TO_PARTY, SXMS_TO_SERVICE, SXMS_TO_NAMESPACE,SXMS_TO_INTERFACE
I am getting alerts when I manually test the alerts configurations by running the report u2018RSALERTTESTu2019.
I am getting mail as :
Alert ID: ##00009##
Dear Administrator,
This is with respect to XI Scenario. During processing of XML file from ECC or XYZ Server, Following error has been occured:
Message ID:
Interface:
NOTE: To check the file name, go to SXMB_MONI and search for above message ID.
Double click on that message ID and click on error in left hand tree.
Please take appropriate action in co-ordination with respective functional and BASIS consultant.
But When I am getting a error , I am not getting an alert mail. Right now iam doing in XI Development.
I am not getting an Alert mail , when my message is in status of : System Error . Error catergory is : XI_J2EE_ADAPTER_JDBC.
Kindly tell how to get alert mail for error catergory : XI_J2EE_ADAPTER_JDBC and in Adapter engine errors.
How to get alert mail when my message is failed with any reason in Adapter engine.
Waiting for quick replay. Please help me out.
Regards,
Ahmed.

Hi thanks for quick reply.
As per your given link : http://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/wlg/14877. [original link is broken]
I have done all these steps. But still little problem.
as per link he is getting Error description , error message id , alert rule..
In my case I am not getting these information. when my messages failed. When I am doing manully testing the alert getting an mail as :
Alert ID: ##00009##
Dear Administrator,
This is with respect to XI Scenario. During processing of XML file from ECC or XYZ Server, Following error has been occured:
Message ID:
Interface:
NOTE: To check the file name, go to SXMB_MONI and search for above message ID.
Double click on that message ID and click on error in left hand tree.
Please take appropriate action in co-ordination with respective functional and BASIS consultant.
Is it okay the body of mail??.
I am not getting alert mail when my messages failed in adapter engine and Integration Engine.
Ex my message is failed in AE:as below.
My messages flow as : SAP --> XI --> DB.
Messages is success (in ECC moni)> XI moni also success> XI Adapter engine getting error as (Status: System Error) and (Error Category : XI_J2EE_ADAPTER_JDBC).
Regards,
Ahmed.

Ping error in RWB for J2SE Adapter Engine

Hi,
we have several external J2SE adapter engines and they function great other than from a monitoring perspective. In RWB "Ping Status" I'm getting the following:
HTTP request failed. Error code: "401". Error message: "Authorization Required"
Suggestions?
Cheers,
Mattias

This is not an answer to your question.
I've tried to get an answer for: how to register J2SE adapter with Integration Server ?
I tried using SLDAccess service on J2SE adapter with no luck (with this J2SE Adapter Engine is registered in the SLD). My J2SE adapter was never available in the configuration means, in the communication channel ex: file adapter, for the adapter engine drop down all I have is Integration Server, my J2SE adapter was never listed there.
If you know an answer please post.
thanks
SKM

J2SE Adapter Engine Error

Hi everyone,
I am facing couple of issues with J2SE adapter engine.
1. First Issue
Config in SLDaccessor -
file adapter java class
classname=com.sap.aii.messaging.adapter.ModuleSLDaccessor
SLD.host=<HOST>
SLD.port=50xxx
SLD.user=user
SLD.password=pass
SLD.adapterEngineName=AdapterEngine
Config in Sender File Channel
file adapter java class
classname=com.sap.aii.messaging.adapter.ModuleFile2XMB
version=30
mode=FILE2XMBWITHROWCONVERSION
XI.SLDConfiguration=SLDaccessor
#XI.TargetURL=http://<HOST>:<50xxx>/sap/xi/engine/?type=entry
XI.TargetURL=<fromSLD>
XI.QualityOfService=EO
XI.Client=001
<Other parameters like InterfaceName / FCC>
If I use XI.SLDConfiguration=SLDaccessor and XI.TargetURL=<fromSLD>, I get an error of HTTP 401 unauthorized.
If I ignore the SLDaccessor, the message is processed successfully.
Am I missing anything in the above configuration?
The user id user is having the roles of SAP_SLD_CONFIGURATOR and SAP_XI_APPL_SERV_USER.
2. Second Issue
In RWB -> Component Monitoring -> J2SE Adapter Engine, there is an error coming up - Unable to establish connection to "https://<LocalHost>:50001/rtc"
The port is wrong ... it should be 8200. My question is, from where to fix this?
Any help will be highly appreciated.
Thanks,
Neetesh

Hi Neetesh,
After copying tech_adapter on your local machine douple click on run_adapter.bat and then open internet explorer and enter http://l<ocalmachine_ip_address>:8200/adapter.html
After doing this you will get logon popup, enter user & password and configure the adapters.
Secondly you can see the port in SLDAPICUST if I am not mistaken. (not very sure)
Compare your configuration with below one
file adapter java class
classname=com.sap.aii.messaging.adapter.ModuleFile2XMB
version=30
mode=FILE2XMB
Integration Engine address and document settings (example, see docu)
XI.TargetURL=http://<host>:8000/sap/xi/engine?type=entry
XI.User=testuser
XI.Password=pass123
XI.QualityOfService=EO
#XI.SenderParty=
XI.SenderService=LocalSystem
#XI.ReceiverParty=
XI.ReceiverService=LocalSystem
XI.Interface=IM_J2SE
XI.InterfaceNamespace=http://abc.com/j2se/test
##File Adapter specific parameters (example, see docu)
file.type=BIN
#file.type=TXT
file.encoding=UTF-8
file.sourceDir=c:/sender
file.sourceFilename=sender1.xml
#file.processingMode=test
file.processingMode=delete
#file.processingMode=archiveWithTimeStamp
#file.archiveDir=./temp_archive
#file.retryInterval=20
file.pollInterval=30
Regards,
Sarvesh

Graphic Mapping:IDOC to File-Avoid Error in Adapter Engine

Hi all,
I'm using Graphic Mapping in my IDOC to File scenario in which each segment in source IDOC will generate a ROW in target File with the condition: DATBI >= currentdate (and some other conditions)
I have a UDF and use the mapping function CREATEIF for this purpose:
DATBI -> UDF -> CREATEIF -> ROW
Problem scenario: In the source IDOC if all the segments have DATBI < currentdate then there is no ROW created, and I get the error in Adapter Engine
Exception in XML Parser (format problem?):'java.lang.Exception: Message processing failed in XML parser: 'Conversion configuration error: Unknown structure ...
How can I avoid this?
I've tried to put this condition using XPATH in Interface Determination and got the error.
There is a way to use function current-date() in XPATH condition?
Thanks for your help,
Elaine

Hi all,
How can I "suppress the row node if condition fails"? I'm new in PI, so please give more details.
My FCC as follows:
Record Structure: Record, Row
Row.addHeaderLine 0
Row.fieldSeparator ,
Record.fieldSeparator 'nl'
Row.endSeparator ; 'nl'
It works fine if the condition satisfied.
In Message Mapping, I've use Test to double check my mapping, and in the scenario that conditions fails, there is no Row in the target message.
Please advise.
Thanks,
Elaine

Error in RWB - Component Monitoring - Adapter Engine

Hi,
After we install an Additional Application Server Instance, we are facing an issue with the Runtime Workbench, specifically with the Adapter Engine status.
On the RWB we're have this error:
Ping Status: Unable to establish connection to
"http://<Additional AS Host>:<Central Instance JAVA Port>/AdapterFramework/rtc"
All the time it's pointing to the Additional AS with the Primary AS Java Port.
We are using a central SLD in PIP system.
We already reviewed, the point 8.12 of the "SAP NetWeaver PI 7.1 Including SAP EHP 1 - Troubleshooting Guide"
Any idea to solve this?
Regards,
GCC PI

Hi GCC,
Please change in the http://<host>:<j2ee_port>/exchangeProfile this settings:
Exchange Profile
Connections:
- com.sap.aii.connect.directory.name
- com.sap.aii.connect.landscape.name
- com.sap.aii.connect.repository.name
RuntimeWorkbench:
- com.sap.aii.rwb.server.centralmonitoring.r3.ashost
Please change the value in the:
Config Tool -> cluster-data -> Global Server -> Configuration ->
Services -> com.sap.aii.af.cpa.svc ->
 SLD.selfregistration.hostName
 SLD.selfregistration.httpPort
 SLD.selfregistration.httspPort
Also see notes: #1113161 - Links in Component Monitoring not working
and #764176 - Error in XI due to inconsistent SLD contents
After that, please restart the j2ee engine.
Regards,
Luis Diego

Reg: Error in adapter Engine Monitoring

Hi Guys,
In my RFC to File Scenario i got error as Adapter message property was configured was mandatory element but there is no Dynamic ocnfiguration elementin XI MEssage Header. This is occur in adapter engine monitoring in RWB.
Thanks

This error comes if you there is a problem in passing the file via dynamic configuration
for this if you want temporary solution like filename not necessarily be dynamic then go to receiver file adapter then
adapter specific message attributes deselect filed Failif file name does not.... sme option where you can uncheck the failure option
and in this case need to provide the filename and file will get generated with this filename if there is no filename generates using dynamic configuration
for this to resolve permanently then check the filename is passed or not to file adapter in moni in dynamicconfiguratuoin tab of callAdapter pipeline service
HTH
Rajesh

Automatic restart of Error-Message in Adapter-Engine (Job?)

Hi,
we are working on PI 7.11 and facing following problem:
Often in message-monitoring error-messages are forgotten because of wrong date-selections by the monitorer (not enough days back). It would be very nice, if there is a function witch is repeating error-messages in adapter-engine automaticly and witch can be scheduled.
Does anybody know something about an excisting program / function on PI?
Regards
Jürg

Hi,
By default if any failure occurs in adapter engine (in case of receiver,during delivery to target system)
it will retry 3 times after a period interval of 5 minutes..this is by default even this can be change if needed with the help of the proeprties at NWA/VA...
but in case of failures at IE level (mappings,...) then you need to schedule the report RSXMB_RESTART_MESSAGES....
search SDN if like to know more about the reports...
HTH
Rajesh

Error JOB MS.JOB.DELETE in Adapter Engine SAP XI 7.0

Hello,
I am getting an error in JOB that deletes messages from the adapter engine of SAP XI 7.0, can someone help me?
Adapter Engine, message: Fatal DeleteJob (Default Delete Job) failed.(Details: Code: MS.JOB.DELETE, Location: com.sap.aii.af.ra.ms.impl.core.archiving.executor.DeleteExecutor, Reason: com.sap.aii.af.ra.ms.api.DeliveryException: Error removing messages or audit log entries with expired persist duration., Time: 14.08.2008 21:00:05)
Thanks
Zanchetta

Hi Roberto,
We have noticed this behavior after our PI system is upgraded to PI 7.0 Ehp1.
It is caused by JDBC driver after upgrade. This issue is resolved in the following new jdbc driver which is available on the SAP Service Marketplace:
DB2 Driver for ODBC and CLI V9.7 FP3a SB27297.
Hope your issue will be resolved by this fix. If it's not resolved, please open up a message with SAP.
Thanks,
Siva Kumar

ALERT not getting triggered for messages in error in adapter engine

Hi All,
I am doing the same scenario where I have created two Alert category Alert_cat1 and Alert_cat2, both are similar but one i have created for error in integration engine(Alert_cat1 ) and other for adapter engine(Alert_cat2).
Now for Alert_cat1 i have created a rule and in the setting "where did the error occur" I have given no restriction.
Now for Alert_cat2,as discussed in the above blog I have created many rule each for various adapter.
I have tested it, above mentioned configuration is working for message mapping error (sxmb_moni)
but not for any error in adapter engine for messages in waiting or system erroe status.
Kindly suggest where I am going wrong.
Regards
Shefali S

HI,
please refer this below blog:
Does Alerts work for Integrated configurations scenario??
thanks,

Error Adapter Engine

Similar Messages

Maybe you are looking for