Error applying an image using imagex

Question

Hello,
I get the following error messages only when applying image to a destination computer. If I reapply the image on the source computer I do not get these errors, please help.
F:\>imagex /apply I:\x201win7x64.wim 1 W: /verify
ImageX Tool for Windows
Copyright (C) Microsoft Corp. All rights reserved.
Version: 6.1.7600.16385
[   0% ] Applying (with verification) progress
[   0% ] Applying (with verification) progress
[   1% ] Applying (with verification) progress
[ ERROR ] W:\MSOCache\All Users\{90120000-0011-0000-0000-0000000FF1CE}-C\ProPlsWW.cab (Error = 577)
Error restoring image.
Windows cannot verify the digital signature for this file. A recent hardware or
software change might have installed a file that is signed incorrectly or
damaged, or that might be malicious software from an unknown source.
I took off the /verify switch from the command to see if there was any difference and I get the following errors.
F:\>imagex /apply I:\x201win7x64.wim 1 W: 
ImageX Tool for Windows
Copyright (C) Microsoft Corp. All rights reserved.
Version: 6.1.7600.16385
[   0% ] Applying progress
[   0% ] Applying progress
[   1% ] Applying progress
[   2% ] Applying progress: 29:24 mins remaining
[   3% ] Applying progress: 27:58 mins remaining
[   4% ] Applying progress: 25:01 mins remaining
[   5% ] Applying progress: 22:23 mins remaining
[   6% ] Applying progress: 19:50 mins remaining
[   7% ] Applying progress: 17:46 mins remaining
[   8% ] Applying progress: 16:06 mins remaining
[ RETRY ] Restoring W:\Program Files (x86)\Adobe\Reader 10.0\Reader\plug_ins\Annots.api again (Error = 1392)
[ RETRY ] Restoring W:\Program Files (x86)\Adobe\Reader 10.0\Reader\plug_ins\Annots.api again (Error = 1392)
[ RETRY ] Restoring W:\Program Files (x86)\Adobe\Reader 10.0\Reader\plug_ins\Annots.api again (Error = 1392)
[ RETRY ] Restoring W:\Program Files (x86)\Adobe\Reader 10.0\Reader\plug_ins\Annots.api again (Error = 1392)
[ ERROR ] W:\Program Files (x86)\Adobe\Reader 10.0\Reader\plug_ins\Annots.api (Error = 1392)
Error restoring image.
The file or directory is corrupted and unreadable.
I captured the image using /check / verify switches and returned successful image capture with no errors.
Please help!

Answer 1

I'm going to try and bring this thread back from the dead.  Buckle up, long post ahead.
Did you ever determine for sure that the issue was a system board?  I'm having a very similar issue with a machine. 
I am trying to apply an image to a customer machine using ImageX, but keep running into error 1392.  This error would flag a different file every time, but always at 45-49% completion. 
The image was provided by the customer in a PE image which was ghosted to multiple flash drives.  We have successfully applied the image to over 400 machines by first using disk part to clean the disk and create one ntfs partition.  We then run "Imagex.exe
/apply path_to_customer_image.wim 1 C:"
That is where this machine would find its hangup and spit out an imagex error 1392.
My initial reaction was to replace the HDD, so I did.  The issue was not resolved, so I tested the ram and CPU with no change.  I replaced the system board with a brand new one, and the issue persists!!  This is basically a new machine by now,
so I've pretty much ruled out hardware related possibilities.
Curious as to the customer's specification on creating just one partition in preparation for imaging, I experimented a little.  I shredded the HDD in Parted Magic and used its partition editor to ensure there were no existing partitions.
Using Disk Part from X: on the imaging flash drive, I cleaned the HDD (why not?) and created an initial ntfs partition of 100mb.  I labeled it "system" and assigned it letter S.  I then created a second ntfs partition of the remaining space,
labeled it "windows," and assigned it letter C.  This partition I marked as active.
I then ran chkdsk to scan for any possible drive errors. 
This time, running Imagex, the process made it to 77% before failing with error 1392 (again, a seemingly random file).  Seeing as how the failures were previously consistently between 45% and 49%, I figured I was on to something.  I repeated all of
the disk prep steps above, making the "system" partition 500mb this time. 
ImageX was a success!!  100% of the WIM was applied and I received no errors.  Fantastic. 
I went to boot the machine and received an error that the boot files were missing.
I booted back into the PE drive and tried running bcdboot to pull boot files and apply to my active OS partition at C:, but I received another error stating that there was a failure attempting to transfer the boot files.  I ran again in verbose and received
an error code.  I cannot remember the error code for certain (I am currently cleaning the HDD), but according to my Google history, it was 0xc1. 
Any ideas??  The machine is an HP EliteBook 8470p.
Update:  Parted Magic just crashed twice attempting to wipe the hard disk.  Once running from RAM, the second time running live from the USB.  This is new....