Error in installing NI 488.2 in PXI system

Hi, all
We have a VA-HR instrument and agilent power supplies, which we are being controlled through USB interface in one computer. all the supplies and VA-HR are controlled via single USB.
Now we want to controll these instruments from another computer which is a PXI system with NI PXI 8105 Embedded controller. (PXI system contains Windows XP service Pack 2)
When the USB cable was plugged into PXI system, it gave folowing message:
Found new hardware, USB serial controller D, and also the GPIB-USB-HS.
So we came to conclusion that it requires USB serial controller D drivers as well as GPIB-USB-HS(GPIB-USB-B) drivers.
For that i did download NI 488.2 2.7.3 from NI website and tried to install that into PXI SYSTEM. But during installation, the process rolled back from driver installation and gave an error. i tried this for atleast three times. In other PC the same .exe source of NI 488.2, successfully installed NI 488.2 software without any error.
I can't understand why this NI 488.2 is not being installed.
LABview 8.6 is already installed in the system.
In short i want to connect my Power supplies and VA-HR to PXI system. Please help me out in this installation error.
thanks and regards,
vishal sakarvadiya

muks
Proven Zealot
What is the error you are getting?
HI, muks
Now I have attached the images with this message which shows sequence of process that was followed during installation of NI 488.2 in PXI system.
STEP-1...
STEP-2...
STEP-3....
STEP-4.....
STEP-5.....

Similar Messages

  • Hp mini 110 boot disk error after installing new hard drive and system recovery

    Need help,  HP mini 110 Windows 7 32 bit.  using my recovery disks I created i was able to recover to the old 160 gb hard drive.  After I installed new 320 Gig drive and used my recovery disks i now get boot disk error. Looks like system was installed on new drive. but will not boot to complete set up.

    If you use the recovery disk, your machine will restore to its default factory state. Try to reinstall the 320 GB you have if you want it to get back.
    Can't get enough of this Envy...

  • Getting Error while installing UCM

    Hi All,
    Am getting error while installing the UCM in my system.
    Error description:-
    NOTICE:     Install logging initialized at 2/5/10 3:34 PM.
    NOTICE:     Installing master server.
    NOTICE:     Installing with Java version 1.5.0_11.
    NOTICE:     Install logging initialized at 2/5/10 3:35 PM.
    NOTICE:     Finished install type QueryConfiguration at 2/5/10 3:35 PM.
    NOTICE:     Install logging initialized for D:/UCM/install/2010-02-05-new.txt at 2/5/10 1:08 PM.
    NOTICE:     Unable to connect to database. Installation will fail.
    ERROR:     Unable to create database connection for the database 'InstallerDatabase' with connection string 'jdbc:oracle:thin:@localhost:1521:ORACLE'. Please make sure that the connection string, user and password are correct. Listener refused the connection with the following error:
    ORA-12505, TNS:listener does not currently know of SID given in connect descriptor
    The Connection descriptor used by the client was:
    localhost:1521:ORACLE
    NOTICE:     Install logging initialized for D:/UCM/install/2010-02-05-new.txt at 2/5/10 1:09 PM.
    NOTICE:     Successfully installed 'ActiveDirectoryLdapComponent' component
    NOTICE:     Successfully installed 'ArchiverReplicationExceptions' component
    NOTICE:     Successfully installed 'CheckoutAndOpenInNative' component
    NOTICE:     Successfully installed 'CheckSCSHealth' component
    NOTICE:     Successfully installed 'CIS_Helper' component
    NOTICE:     Successfully installed 'ContentFolios' component
    NOTICE:     Successfully installed 'ConfigMigrationUtility' component
    NOTICE:     Successfully installed 'FileStoreProvider' component
    NOTICE:     Successfully installed 'Folders_g' component
    NOTICE:     Successfully installed 'Helper' component
    NOTICE:     Successfully installed 'FormEditor' component
    NOTICE:     Successfully installed 'InboundRefinerySupport' component
    NOTICE:     Successfully installed 'LinkManager8' component
    NOTICE:     Successfully installed 'OracleTextSearch' component
    NOTICE:     Successfully installed 'OracleQueryOptimizer' component
    NOTICE:     Successfully installed 'ProxyConnections8' component
    NOTICE:     Successfully installed 'ThreadedDiscussions' component
    NOTICE:     Successfully installed 'CoreWebdav' component
    NOTICE:     Successfully installed 'WebUrlMapPlugin' component
    NOTICE:     Successfully installed 'WsdlGenerator' component
    NOTICE:     Successfully installed 'DBSearchContainsOpSupport' component
    NOTICE:     Successfully installed 'UserProfileSchemaLoader' component
    NOTICE:     Successfully installed 'FCKEditor' component
    NOTICE:     Successfully installed 'NativeOsUtils' component
    NOTICE:     Successfully installed 'ContentAccess-win32' component
    NOTICE:     Successfully installed 'ComponentTool' component
    NOTICE:     Successfully installed 'CoreUserInterfaceLibrary' component
    NOTICE:     Successfully installed 'Localization' component
    NOTICE:     Successfully installed 'SecurityProviders' component
    NOTICE:     Successfully installed 'PopUpCalendar' component
    NOTICE:     Successfully installed 'YahooUserInterfaceLibrary' component
    NOTICE:     Successfully installed 'iTextComponent' component
    NOTICE:     Installing shortcuts
    WARNING:     Unexpected exception: Unable to initialize the system provider 'SystemDatabase'. Unable to create database connection for the database 'SystemDatabase' with connection string 'jdbc:oracle:thin:@localhost:1521:ORACLE'. Please make sure that the connection string, user and password are correct. Listener refused the connection with the following error:
    ORA-12505, TNS:listener does not currently know of SID given in connect descriptor
    The Connection descriptor used by the client was:
    localhost:1521:ORACLE
    WARNING:     Unable to publish user database.
    WARNING:     Unable to register with Administration Server.
    NOTICE:     Finished install type Install with warnings at 2/5/10 1:12 PM.
    Help me on this issue

    Hi Srinath,
    again i am getting same exception ....if you feel free , check once
    NOTICE:     Install logging initialized at 2/5/10 5:06 PM.
    NOTICE:     Installing master server.
    NOTICE:     Installing with Java version 1.5.0_11.
    NOTICE:     Install logging initialized at 2/5/10 5:06 PM.
    NOTICE:     Finished install type QueryConfiguration at 2/5/10 5:06 PM.
    NOTICE:     Install logging initialized for D:/UCM/install/2010-02-05-new.txt at 2/5/10 2:38 PM.
    NOTICE:     Unable to connect to database. Installation will fail.
    ERROR:     Unable to create database connection for the database 'InstallerDatabase' with connection string 'jdbc:oracle:thin:@localhost:1521:orcl'. Please make sure that the connection string, user and password are correct. ORA-01017: invalid username/password; logon denied
    NOTICE:     Install logging initialized for D:/UCM/install/2010-02-05-new.txt at 2/5/10 2:38 PM.
    ERROR:     Unable to create database connection for the database 'InstallerDatabase' with connection string 'jdbc:oracle:thin:@localhost:1521:orcl'. Please make sure that the connection string, user and password are correct. ORA-01017: invalid username/password; logon denied
    ERROR:     Unable to create database tables. You will have to create them manually.
    NOTICE:     Successfully installed 'ActiveDirectoryLdapComponent' component
    NOTICE:     Successfully installed 'ArchiverReplicationExceptions' component
    NOTICE:     Successfully installed 'CheckoutAndOpenInNative' component
    NOTICE:     Successfully installed 'CheckSCSHealth' component
    NOTICE:     Successfully installed 'CIS_Helper' component
    NOTICE:     Successfully installed 'ContentFolios' component
    NOTICE:     Successfully installed 'ConfigMigrationUtility' component
    NOTICE:     Successfully installed 'FileStoreProvider' component
    NOTICE:     Successfully installed 'Folders_g' component
    NOTICE:     Successfully installed 'Helper' component
    NOTICE:     Successfully installed 'FormEditor' component
    NOTICE:     Successfully installed 'InboundRefinerySupport' component
    NOTICE:     Successfully installed 'LinkManager8' component
    NOTICE:     Successfully installed 'OracleTextSearch' component
    NOTICE:     Successfully installed 'OracleQueryOptimizer' component
    NOTICE:     Successfully installed 'ProxyConnections8' component
    NOTICE:     Successfully installed 'ThreadedDiscussions' component
    NOTICE:     Successfully installed 'CoreWebdav' component
    NOTICE:     Successfully installed 'WebUrlMapPlugin' component
    NOTICE:     Successfully installed 'WsdlGenerator' component
    NOTICE:     Successfully installed 'DBSearchContainsOpSupport' component
    NOTICE:     Successfully installed 'UserProfileSchemaLoader' component
    NOTICE:     Successfully installed 'FCKEditor' component
    NOTICE:     Successfully installed 'NativeOsUtils' component
    NOTICE:     Successfully installed 'ContentAccess-win32' component
    NOTICE:     Successfully installed 'ComponentTool' component
    NOTICE:     Successfully installed 'CoreUserInterfaceLibrary' component
    NOTICE:     Successfully installed 'Localization' component
    NOTICE:     Successfully installed 'SecurityProviders' component
    NOTICE:     Successfully installed 'PopUpCalendar' component
    NOTICE:     Successfully installed 'YahooUserInterfaceLibrary' component
    NOTICE:     Successfully installed 'iTextComponent' component
    NOTICE:     Installing shortcuts
    WARNING:     Unexpected exception: Unable to initialize the system provider 'SystemDatabase'. Unable to create database connection for the database 'SystemDatabase' with connection string 'jdbc:oracle:thin:@localhost:1521:orcl'. Please make sure that the connection string, user and password are correct. ORA-01017: invalid username/password; logon denied
    WARNING:     Unable to publish user database.
    WARNING:     Unable to register with Administration Server.
    NOTICE:     Finished install type Install with warnings and with errors at 2/5/10 2:42 PM.
    Regards,
    Vijay

  • Error while installing J2EE Add- In to the ABAP system

    Error while installing J2EE Add-In to the ABAP system 
    We are installing J2EE Add-In to the ECC5 System in the new hardware.
    When are getting Error while installing J2EE Add-In to the ABAP system.
    Transaction Begin*****************************
    ERROR 2005-08-10 14:58:28
    CJSlibModule::writeLogEntry()
    CJS-20011 J2EE engine configuration error. DIAGNOSIS: Error when
    configuring J2EE Engine. See output of
    logfile /usr/sap/QSS/install/batchconfig.log: 'My Library Path
    is: /usr/j2se/jre/lib/sparcv9/server:/usr/j2se/jre/lib/sparcv9:/usr/j2se/jre/../lib/sparcv9:/tmp/sapinst_exe.13084.1123702275:/usr/lib::/usr/openwin/lib:/usr/sap/QSS/SYS/exe/run:/oracle/QSS/920_64/lib:/oracle/QSS/920_64/lib32:/usr/lib
    ElementInfoTask has finished successfully on dispatcher
    ConsoleLogsTask has finished successfully on dispatcher
    ChangeManagerPropsTask has finished successfully. Manager:
    LockingManager on dispatcher
    ChangeManagerPropsTask has finished successfully. Manager:
    ClusterManager on dispatcher
    ElementInfoTask has finished successfully on server
    ConsoleLogsTask has finished successfully on server
    ChangeManagerPropsTask has finished successfully. Manager:
    LockingManager on server
    ChangeManagerPropsTask has finished successfully. Manager:
    ClusterManager on server
    ChangeServicePropsTask has finished successfully. Service: dbpool on
    server
    ChangePasswordsTask finished successfully.
    Error occured while connecting to database (UploadFile). Msg: No such
    algorithm: DESede
    Transaction end***********************************
    We tried twice clean installation, after removing j2ee dir, SCS and
    resp profiles and droping PSAPQSSDB tablespace and SAPQSSDB user.
    I have also confirmed the passwords in ABAP system/000 for SAPJSF, DDIC, J2EE_ADMIN, J2EE_GUEST.
    We are getting the same error in both tries.
    Kindly advice us to resolve the problem.
    Thanks and Regards,
    Srinivas

    Ananda,
    you saved my day!  I've been banging my head against the wall with this same problem during a J2EE add-in installation for SRM 4.0 on Windows, in preparation of an LAC 2.0 installation.  I had tried deleting the schema first, but that didn't work.  After I removed the sys\global\security folder as well, it worked perfectly.
    Thank you.

  • Error while installing Mini SAP Basis system 4.6D test suite

    Hi Gurus,
    I am getting error while installing Mini SAP Basis system 4.6D test suite on my laptop. I trying to install this version under Windows Xp. I tried so many times to rectify this error but no use. i followed the instruction in the readme file.The error is below in quote.
    "InstController MakeStepsDeliver:108 connection to GUI of installation tool has been cut  off.Installation has been stopped."
    your help very much appreciated...
    Regards
    dinesh.a

    is win xp supported for mini sap 46d?
    -> try netweaver 2004s instead ...
    GreetZ, AH

  • HT1151 I keep getting an error message when installing new software that says "System extension cannot be used /system/library/extension/IoFireWireWDHID.kext was installed improperly" I have no idea what this means and all of my software seems to install

    I keep getting an error message when installing new software that says "System extension cannot be used /system/library/extension/IoFireWireWDHID.kext was installed improperly" I have no idea what this means and all of my software seems to install okay

    Hello Valerie Anderson,
    I'm Harry from Norton Support team. Please check the information provided in a similar thread here:
    https://discussions.apple.com/message/21854775#21854775
    Let me know if this helps.
    Thanks!
    Harry

  • I just installed Lion and the newest version of Logic express 9 (9.1.5) and every time i playback audio I get this error message:  [Disk is too slow or System Overload. (-10010) . Never had any issues before now...

    I just installed OSX Lion (10.7.2) and updated to the newest version of Logic express (9.1.5) on a macbook and every time I playback audio I get this error message:  [Disk is too slow or System Overload. (-10010) The Sudden Motion Sensor may have parked the hard drive head, or the disk performance is not sufficient to read or write all audio tracks, or the system was not able to process all data in time]
    Never had any issues before now... any ideas?

    Have a look into the Preferences folder (YourUserFolder/Libraries/Preferences/) and trash all Logic preferences.
    You'll have to setup the program again.
    cheers
    rob

  • On my Windows 7 64-bit system,  I get a "Shared Technologies" error on installing Photoshop Elements

    On my Windows 7 64-bit system,  I get a "Shared Technologies" error on installing Photoshop Elements 11

    Hi Abhijit.
    Well, after renaming C:\Program Files (x86)\Common Files\Adobe to OOBE-old,
       I still get this error:
    This is MOST Frustrating. Any other advice would be greatly appreciated!
    Thank you,
    Steve
    Stephen A. Solomon MBA
    <Removed by Moderator>

  • Error while Installing Hyperion system 9.0

    Hi,
    my requirement is
    to install lisence server and BI+ services in system A,and Shared services,BI+ UI services in system B.both are in lan.
    i installed lisenced server,shared services and BI+ services accordingly and configured successfully.
    But while installing BI+ UI services in system B
    the following error came.
    Errors occurred during the installation.
    Unable to install Hyperion System 9 BI+ UIServices over Single-installer Suite: Installed product has newer version.
    thank you

    Hi,
    Yes,  9.0 version will not support above server. Please check below guide:
    http://www.abbasoft.com/images/Hardware_software_requirements.pdf
    Thanks  & Regards,
    Nagarajan

  • No mountable File System error while installing Flash Player

    Hi all,
    i've been having a no mountable file system error while installing Flash Player.  At first i thought it was a problem with the download but i've tried many times and still have the same error when installing the player.  I've attached a screenshot of the error message.
    Hopefully someone can shed some light.  I'm using a 2012 Mac Mini running Mountain Lion on a Fusion Drive.

    elliott777 wrote:
    Thank you for your help! I don't have the capabilities:(
    you don't have what capabilities? to download?

  • Installed PCI-6025E recognized by Windows XP but only in PXI system by MAX

    I installed a PCI-6025E DAQ board on a Windows XP machine. Upon startup it recognized the new hardware and installed the driver from the NI-DAQ 6.9.3 CD. All seemed to work fine. When I try to bring up the device in MAX it only shows up in the PXI system section. This doesn't assign a device number or allow a test panel. So I don't know how to access the signal from Labview programs. Is there something I haven't done right?

    Hello magicjoecuda,
    In general it sounds like you have done everything right and it is not that surprising that the 6025E shows up as a PXI device, but it is unexpected that it does nost appear as a DAQ device. I would try 2 things to work around this:
    1) Try installing the card in a different PCI slot on the computer.
    2) Uninstall the 6.9.3 driver and try installing the newest version of the driver. A link to the newest version of the driver for your board can be found here:
    http://www.ni.com/support/daq/versions_pci_pxi.htm
    Take care,
    E.Lee
    Eric
    DE For Life!

  • Error: The installed graphics card does not meet the minimum system requirements by Aperture

    I have a Mac Pro 3.1 10.5.8 and Aperture 2.1.4.  My NVida 8800gt with 512 mb was over heating so I brought and install the ATI radeon hd 5770 to replace it.  Now when I try to start Aperture I get this message "Error: The installed graphics card does not meet the minimum system requirements by Aperture".  All other software works fine, ie photoshop elements and Safari.  When I install my old card aperture will open with no problem, but of course the card will overheat within 10 mins and I will have no video.  I have search on google with no luck.  Will upgrading to Aperture 3 fix this problem?

    5770 requires 10.6.5.
    The 8800GT - there is the 350* bake in over 10 minutes - 50% or better chance
    you can find 8800GT on http://myworld.ebay.com/macvidcards/
    http://www.macupdate.com/info.php/id/23049/smcfancontrol
    http://www.bresink.com/osx/HardwareMonitor.html
    Fan control helps with FBDIMMs which need to be kept under 70C too.

  • Why do I get Error 1627 when installing NI-488.2 ver 2.2SW on WinXP?

    when installing NI-488.2 on a win XP laptop I get the following error what do I need to do?
    MsiError 1627: 1: 2707 2: WindowsFolder.47899608_E211_483A_A7CE_0FDFB1FC04F3
    Exception code: E06D7363 ()
    Fault address: 7C81EB33 0001:0001DB33 C:\WINDOWS\system32\kernel32.dll
    Registers:
    EAX:00D9FA4C
    EBX:0046A160
    ECX:00000000
    EDX:0051ED38
    ESI:00D9FADC
    EDI:00D9FADC
    CS:EIP:001B7C81EB33
    SS:ESP:002300D9FA48 EBP:00D9FA9C
    DS:0023 ES:0023 FS:003B GS:0000
    Flags:00000206
    Stack Trace
    Address Frame LogicalAddr Module SymbolName + Offset
    7C81EB33 00D9FA9C 0001:0001DB33 C:\WINDOWS\system32\kernel32.dll RaiseException + 82
    004D0E5F 00D9FADC 0001:000CFE5F E:\NI-488.2\Setup.exe
    00479A63 00D
    9FBBC 0001:00078A63 E:\NI-488.2\Setup.exe
    004272F7 00D9FCC4 0001:000262F7 E:\NI-488.2\Setup.exe
    00469FEC 00D9FD78 0001:00068FEC E:\NI-488.2\Setup.exe
    0046A0E6 00D9FD9C 0001:000690E6 E:\NI-488.2\Setup.exe
    00472121 00D9FDE4 0001:00071121 E:\NI-488.2\Setup.exe
    004721DE 00D9FF18 0001:000711DE E:\NI-488.2\Setup.exe
    004F7119 00D9FF80 0001:000F6119 E:\NI-488.2\Setup.exe
    004D69AE 00D9FFB4 0001:000D59AE E:\NI-488.2\Setup.exe
    7C80B50B 00D9FFEC 0001:0000A50B C:\WINDOWS\system32\kernel32.dll GetModuleFileNameA + 436

    Hi,
    First make sure that you are installing the software as an Administrator so that you have access to all the registries. Now, if logged in as an Administrator and you are still having this error, check the following link.
    How Do I Install LabVIEW if I Receive an Error During the Installation?
    This document is valid for any software that installs from a CD. Basically is copying the content of the CD into the Hard Disk and running the install from the HD.
    If that doesn't fix the problem then try installing the driver in a different machine just to make sure that it is not the software in the CD that is corrupted. If it is corrupted then you can
    download the driver from the GPIB Drivers page.
    Make sure that every time you want to install or reinstall the driver, that you uninstall the previous version and reboot the computer before installing the new one.
    Hope this helps.
    Ricardo S.
    National Instruments.

  • I am using XNET CAN on a PXI system. When I modify the can database I get the error "the interface has already been opened.."

    I have tried both building the XNET session from project explorer and by building a signal list in the VI.
    Any suggestions? Thanks in Advance.

    Thanks for the reply. I don't think I have any interface open. But to be sure, I rebooted everything - same result.
    Is there some step in the project config that I am failing to do? In the PXI systems I had before XNET, I had to setup some CAN configuration stuff in MAX to get it to work, but I don't see that option anymore with XNET.... 
    I have been sucessful in running XNET CAN VIs reading and writing the data from my database, but I stumble every time I add a signal or rename the database. 
    I made a simplified VI to illustrate, using a previously working database I now get the empty name message.(screen capture attached)
    This is connected to a working CAN link, and I can see these signals in MAX properly.  
    Thanks in advance for your assistance!
    Attachments:
    vi_issue1.jpg ‏136 KB

  • PXI System does not appear in MAX 4.0

    Hello,
    My system comprises LabVIEW RT 7.0, target PXI-8176 controller in PXI-1000B chassis, PXI-6608, PXI-6711, NI-4472, PXI-6704, PXI-6527, PXI-8423/4, PXI-8422/4.  This has been stable for two years. I recently solved an RS-485 2-wire mode configuration problem, using information in a discussion forum thread, by upgrading to NI-VISA 3.4.1 and NI-Serial 2.5.5.  MAX 4.0 was installed as part of this process.  Everything seemed to work fine.  I instructed a distant customer to do the same, but they experienced some difficulty. To ensure we were working from the same starting point, I re-initialized my PXI system, using PXI Format Hard Drive Disk, version 7.0, from MAX 4.0.  I configured TCP IP address, and re-installed the RT software on the PXI controller.
    Next, I attempted to configure the PXI controller and chassis, in MAX, to update the pxisys.ini file, but the PXI System (Unidentified) does not appear under Remote System>>IP address>>Devices and Interfaces.  Similarly for the serial ports.  This worked before, but I cannot get this back.  What is wrong?
    Best regards,
    RonC

    Hello S. Bassett
    The controller is definitely booting in RT mode -- I can still run my applications on the RT target.  VISA seems configured properly also, I can make VISA calls without error in the application.
    In fact, the RT system seems to work correctly, and I contemplated leaving it as it is. However, the fact that MAX does not recognize the PXI system makes me nervous, and I cannot do some of the things I may want to do, for example independently configure RS-485 port wire mode in MAX (the ports do not show up either).  Traditional DAQ configuration in MAX works.
    After your last post, I found a brief reference in MAX Help that indicated "PXI Services" had to be downloaded before the chassis could be configured.  But there are no other mentions of what PXI Services is, what it does, or how to install them. PXI Services does not show up as RT Software in MAX. In the Windows Add/Remove Programs control panel in Windows, in the National Instruments software section, there are two apparently related entries:
    - NI PXI Platform Services for LabVIEW Real-Time 1.5.1
    - NI PXI Platform Services for Windows 1.5.1
    But, I cannot get these to install on the RT target.  Not knowing what was causing the problem, I uninstalled everything from  National Instruments, deleted all folders, and reformatted the PXI platform.  There was one problem during this process -- after uninstalling NI-Serial 2.5.5, it does not get removed from the Add/Remove programs control panel.  There is still a registry key that the uninstaller did not remove -- presumably this is the problem.
    I have rebuilt everything, but could not get NI-Serial to install -- the installer thinks there is a newer installed on the RT target (there isn't) and refuses to install NI-Serial 2.5.5.  So right now, I cannot install NI-SERIAL (any version), or remove the 'existing' NI_SERIAL, because it isn't actually there, and there is no uninstaller.
    Otherwise, everything seems to be back to where it was before I "upgraded" to NI-VISA 3.4.1.  This was NI-VISA 3.0, LV RT 7.0, and MAX 3.0.2.  I have not yet been able to install NI-Serial, so I cannot yet see if I have also restored my original problem -- the one that led me to have to upgrade NI-VISA and NI-SERIAL in the first place.
    Most importantly, there is now a "PXI Services v1.1.2" installed on the RT target.  I am quite sure the problem with MAX 4.0 not recognizing my PXI system has to do with the absence of this driver on the RT target.
    Thanks again for your interest and help,
    RonC

Maybe you are looking for

  • How do I edit photos on 5th generation ipod

    Since updating to newest ipod & itunes software I'm unable to get any response from the tabs when clicking on my ipod in itunes on my computer. The instructions say to click on ipod then click on the photo tab then happens when I try to click on the

  • Nokia Asha 306 Conversations

    Hello there , I have a question : if you could clear this up for me - how can I transfer my text messages from Nokia SUITE to Nokia Asha 306 in their exact order? I know this could be done, but I don't know how. Otherwise, why did technology evolve s

  • AUC Deletion

    Hi I have created some AUC's (Assets)through Project Builder (CJ20N)via WBS Element. Now i would like to delete those assets.But System Giving an error mesg says that" Asset _______ belongs to an investment measures.Deletion Not Allowed." Kindly prov

  • Submitting data from PDF vs. HTML

    I have a PDF form rendered from LC Forms that I have been using for a while. It has a submit button on it that has been set to submit the form field data as XML Data. This has been working fine. I now have saved the form as an XDP and am rendering it

  • Read Note content in Records Management (RM)

    Hello, Does anybody know, how to read the content of a note (SRM_SP_NOTE) in RM?