Error opening device
I'm facing some peculiar problems while communicating with the devices using GPIB
I have developed two GUI's in VB 5.0 which tries to communicate with two instruments(DMM) simultaneously( need to say I'm trying to communicate with two instruments at a time). Both the GUI's works fine for 6 times. 7th time I don't know ,I get an error as " Unable to Open Device" . If I close the application and rerun ,it agian works fine for 6 times. 7th time again hangs .And, when i get error in one application , the other also stops . If I try running a single application , it works fine for 12 times, 13th time same problem. And one more, the application is not hanging at the same point. There are no loops in my program . System what I'm using is Dell PC PII
and 192MB RAM.
Please let me know the possible solutions for this and more over if I use two GPIB cards whether it's going to solve the problem.
Hi Ray,
Thanks for the reply.
As u said I tried capturing calls in NI-spy , but didnt' find anything that could solve my problem. After some 2900 calls (when running a single GUI) ibdev call fails . I'm sending a bmp file as an attachment which I captured after gettin the error. When I try runnning two GUIs the , error occurs somewhere near 1500 calls.
I probably feel this is an error related to memory addressing.
Attachments:
Error.jpg 122 KB
Similar Messages
-
DIAGNOSTIC ERROR: OPEN DEVICE (Hard Drive test error)
I have the problem where the ipod at boot time tells me to go to apple.com/support, and i cannot boot into disk mode. Diagnostic test of the Hard Drive instead of listing the HD details, simply says '[Open Device...]' for a few seconds, beeps, and then says '[Can't Open Device]' and halt's the Diag. Also, when left to boot naturally (and fail) the harddrive makes very unnatural clicking sounds, so its obviously nackered.
Obviously then this is a Hard Drive problem, but I'm also hearing that it could be caused by the ribbon? Before I pay out for a new harddrive then I thought I'd double check the validity of this claim. Anyone have any experience with ipod harddrive failures?Didn't mean to make those links, first one should just say "Open Device..."
-
Cannot open Device error 90:54
I have an MSL4048 tape library, that has 2 drives. I have one job that when it runs on drive 2 I get the following error
[Warning] From: HPBMA@nwnode02 "HP:Ultrium 5-SCSI_1" Time: 6/17/2014 6:02:26 PM
[90:54]
Cannot open device (5:1:0C)
[Normal] From: HPBMA@nwnode02 "HP:Ultrium 5-SCSI_1" Time: 6/17/2014 6:02:26 PM
ABORTED Media Agent "HP:Ultrium 5-SCSI_1"
[Critical] From: [email protected] "Netware-Node02" Time: 6/17/2014 6:02:27 PM
None of the Disk Agents completed successfully.
Session has failed.
But if I run this on drive 1 that job completes normally.You're trying to load a defective web page that's configured only to allow certain browsers to connect.
Sometimes the Firefox browser may be able to connect to such a page, or sometimes you may be able to fool the server into thinking you're running IE.
If the Develop menu isn't showing in the Safari menu bar, select
Safari ▹ Preferences... ▹ Advanced ▹ Show Develop menu in menu bar
Then select
Develop ▹ User Agent ▹ Internet Explorer 8.0 (or 9.0 or 10.0)
Try again to load the page. Although this ruse may get you past the blocking page, it does not cause Safari to behave like IE, and the site may not work. -
[SOLVED]Error opening PCM device hw:0,0
I am trying to use Jesusonic, but I get the following error:
mmanu > Desktop/jesusonic-0.991-linux-x86/jesusonic -mode ALSA -nbufs 2
Jesusonic v0.991 - Copyright (C) 2004-2005 Cockos Incorporated
Using output mode: 'ALSA'
Opening ALSA 'hw:0,0' for read
Opening ALSA 'hw:0,0' for write
Error opening PCM device hw:0,0
My audio card is an integrated Intel one:
Audio device: Intel Corporation module: snd-hda-intel
82801G (ICH7 Family) High Definition Audio Controller
I am not very expert with audio devices and functionality, so is there anything I can look up or do to solve this problem?
Thank you for your timeMy lack of understanding is really showing here...
The default format for alsa is implicitly defined like this:
jesusonic -mode ALSA -in hw:0,0 -out hw:0,0
I'm posting this in the hope that someone that knows hardware will be able to tell you how to identify the proper address. Of course another (very hackish) solution is to just try some other value like hw:0,1 on both. 0,0 and 0,1 work on my machine, but it fails with the same error you have on 0,2.
Last edited by skottish (2008-09-21 16:17:33) -
Can't format external HDD using terminal: Error: -69877: Couldn't open device
Disk Utility won't format / erase Seagate Barracuda 2TB (ST2000DM001) - it is an internal drive but I connected it using a docking station via USB. The disk is brand new and unformatted. System indicates that it is S.M.A.R.T incompatible
When trying to erase the disk, I get error message "disk / link could not be found / opened".
I tried using terminal "diskutil eraseDisk HFS+ newdisk /dev/disk3" but I get this message:
Started erase on disk3
Unmounting disk
Error: -69877: Couldn't open device
Any way I could force format the disk?Thank you @MrHofman. I had a setup with 2 dock stations and 2 HDDs (my TimeCapsule had crashed and I needed to recover its content disassembling the "box"). I disconnected everything. I restarted the computer., I swithched the USB ports in which I had connected the dock stations; I swithched the HDDs from dock stations, and voilà, the system allowed me to format the "recovery" HDD. Sometimes the "simplest" solutions work...
@Linc Davis: prior to the fix described above, when trying to partition, same thing would occur : "can't open link / disk" error message. But now it seems to be working fine. Thank you anyway! -
Open Error 6: Device not configured
I recently had my hard drive replaced and restored to factory settings. I then used a time machine backup and the Migration Assistant to get everything I had back to where it belonged.
Things worked for a day or so, but with a few crashes here and there. Yesterday, I tried to use iTunes and kept getting an error message about the database (-50, unable to mount database). The problem is that the whole system would freeze and I had to shut down and restart every time. Sometimes I could load the OS, sometimes not. This morning I ran Disk Utility to verify the disk (it passed) and the permissions. When I tried to repair permissions, I got hundreds of messages like this : "Open Error 6: Device not configured on" and then a list of paths, such as "System/Library/Perl/5.10.0/darwin-thread-multi-2level/auto/POSIX/getgrgld.al", and "System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/share/ri/....." etc. Literally hundreds of those messages.
Does anyone know what this means? And how should I fix it?!?
Thanks!I'm going to suggest that you ask in the Snow Leopard forums here:
http://discussions.apple.com/category.jspa?categoryID=263
This is likely a system software error, and the SL gurus that hang out over there might have suggestions for you.
Good luck! -
Get error when opening device with example code
I look in measurement and automation tool and see my device as device 1 but when I run the "Read Dig Chan" example application I get error -200220 - "Device indentifier is invalid"
Hey Grssmith,
Check to make sure your device is present in the Measurement and Automation Explorer under NI-DAQmx Devices. Depending on which board you�re using it will most likely be listed under both NI-DAQmx Devices and Traditional NI-DAQ Devices. The Read Dig Chan example uses the NI-DAQmx driver so it references the device labeling under NI-DAQmx Devices. If you are using the Read Dig Chan LabVIEW example all of your available choices should populate in the pull-down menu of the I/O control.
Please post back if you�re still having problems.
Sarah Miracle
National Instruments -
To open "device manager" install Java SE 6 runtime error message on bouts
Why does To open "device manager" install Java SE 6 runtime appear every time I boot up computer after installing upgrade to Yosemite 10.10 OS
You must have some application called "device manager" which is set to run at startup. Do you know what it is?
Go to System Preferences->Users and Groups, then select the "Login Items" tab and see what's there. Remove anything you don't recognize.
If it's an application you know, and you want to run, then you're going to have to install Java on your machine. Honestly, I'd recommend against it; the application must be quite old. -
Error publishing from Muse - "error updating device redirect setting"
After recent upgrade of Muse I am getting an error message when publishing. The pages are published correctly but there is an error which prevents the final completion of the process. message = "Error updating device redirect settings click resume to try again." it never works. What is up? is this a Business Catalyst error or a a Muse error?
I turned off the firewall, logged out from Creative Cloud and restarted my computer. After rebooting, I logged in to Creative Cloud, open Muse and connect to Business Catalyst without no problem,
-
Error message " Device driver software was not successfully installed. Please consult with your device manufacturer for assistance getting this device installed. Digital Still Camera- Failed" HELP!
Hi, I was able to reformat my iPod and that worked. I read it on one of the threads and I am copy pasting the method below:
I opened the "My Computer" window and right-clicked on my ipod, and then selected "Format". I select "Yes" to format since I don't have anything on the nano to delete anymore.
I then Eject my nano from the computer and did a restart while the nano is disconnected from the computer.
Once Windows finish loading I reconnect the USB to the nano(back of computer) which automatically pulls up iTune. It asked me to name the new ipod detected and created a playlist for that specific ipod name.
Pasted from <http://discussions.apple.com/thread.jspa?threadID=1050784&tstart=15>
Thanks! -
I keep getting the following message when trying to open a PDF I know nothing wrong with the file as it opens fine on other devices ?
"There was an error opening this document. The file is damaged and could not be repaired."No its not zipped
Brian Blackstock
[email protected]
Office Australia +61 7 54537982
Office South Africa +27 11 423 2701
Mobile South Africa +27 796924094
Mobile Australia +61 400797124
www.atoll.co.za
www.elematicsa.co.za -
Error opening the notification Center. I can't open the notification Center
Error opening the notification Center. I can't open the notification Center
Hey amabnn,
Thanks for the question. I understand you are experiencing issues with the latest iTunes update. Let’s troubleshoot the iTunes installation by completely removing and reinstalling iTunes and all related components (it is important to remove all components in the order listed):
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/HT1923
Additional Information:
Issues installing iTunes or QuickTime for Windows
http://support.apple.com/kb/HT1926
How to restart the Apple Mobile Device Service (AMDS) on Windows
http://support.apple.com/kb/TS1567
Thanks,
Matt M. -
Access Denied Error Opens when Installing HP Monitor Software (Windows 7)
im getting the following error trying to upgrade my screen driver.
"Access Denied Error Opens when Installing HP Monitor Software (Windows 7)"
I found this error in the help area but it doesnt address the problem, it simply describes the device manager instalation procedure, which I am using , and which results in the error.Hi debgibson,
What is the monitor model number and what is the PC model number?
...an HP employee just trying to help where I can, but not speaking on behalf of HP. -
Aperture error opening database for library
I was working in Aperture--deleting photos--when it crashed. My Mac Book Pro rebooted but in trying to open Aperture after it rebooted, I got this message:
"There was an error opening the database for the library “/Users/rick/Pictures/Aperture Library.aplibrary”. My only option on the pop-up was to quit.
I found a suggestion here online to find the Aperture library, hold Command-Option and double click the library which supposedly would bring up a repair menu. It didn't. I got the same message as i did on trying to open Aperure quoted above, and again the only option was to quit Now I can't even open Aperture.
Any ideas how to get my library back? Thanks.Here is the Etresoft report. The only software I can recall recently installing is Dashlane. And I did have the local Apple store recently install new memory (from 4 GB to 8) but other than that I don't recall other changes. I believe Aperture is the most current version. To check, I'll have to log on to the other account because that is now the only way I can get Aperture to open. Should I do that?
Hardware Information:
MacBook Pro (13-inch, Mid 2009)
MacBook Pro - model: MacBookPro5,5
1 2.53 GHz Intel Core 2 Duo CPU: 2 cores
8 GB RAM
Video Information:
NVIDIA GeForce 9400M - VRAM: 256 MB
System Software:
OS X 10.8.4 (12E55) - Uptime: 0 days 0:45:0
Disk Information:
FUJITSU MJA2500BH FFS G1 disk0 : (500.11 GB)
disk0s1 (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) /: 499.25 GB (19.05 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
HL-DT-ST DVDRW GS23N
USB Information:
Apple Inc. Built-in iSight
Apple Internal Memory Card Reader
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
Kernel Extensions:
Problem System Launch Daemons:
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[loaded] com.fitbit.galileod.plist
[loaded] com.microsoft.office.licensing.helper.plist
Launch Agents:
[loaded] com.hp.devicemonitor.plist
[loaded] com.hp.messagecenter.launcher.plist
[not loaded] com.sony.ReaderDesktop.RunReaderDesktop.plist
[not loaded] com.sony.ReaderLibrary.RunReaderLibrary.plist
User Launch Agents:
[failed] com.apple.CSConfigDotMacCert-[redacted]@me.com-SharedServices.Agent.plist
[not loaded] jp.co.canon.Inkjet_Extended_Survey_Agent.plist
User Login Items:
iTunesHelper
Reader Library Launcher
Canon IJ Network Scanner Selector2
readerAppHelper
Dropbox
Fitbit Connect Menubar Helper
3rd Party Preference Panes:
Flash Player
Flip4Mac WMV
Internet Plug-ins:
CANONiMAGEGATEWAYDL.plugin
EPPEX Plugin.plugin
Flash Player.plugin
FlashPlayer-10.6.plugin
Flip4Mac WMV Plugin.plugin
GarminGpsControl.plugin
googletalkbrowserplugin.plugin
iPhotoPhotocast.plugin
JavaAppletPlugin.plugin
npgtpo3dautoplugin.plugin
OfficeLiveBrowserPlugin.plugin
QuickTime Plugin.plugin
SharePointBrowserPlugin.plugin
Silverlight.plugin
User Internet Plug-ins:
CitrixOnlineWebDeploymentPlugin.plugin
ContentManager.plugin
Dashlane.plugin
RocketEngine.plugin
UploadManager.plugin
Bad Fonts:
None
Top Processes by CPU:
2% WindowServer
2% WebProcess
1% EtreCheck
1% HP Device Monitor
1% Safari
1% Fitbit Connect Menubar Helper
0% fontd
0% WebKitPluginHost
0% DashlaneAgent
0% Console
Top Processes by Memory:
546 MB WebProcess
139 MB WebKitPluginHost
90 MB Safari
82 MB Pages
74 MB Dropbox
66 MB mds
57 MB WindowServer
49 MB Finder
49 MB DashlaneAgent
49 MB Dashlane
Virtual Memory Statistics
5.10 GB Free RAM
1.73 GB Active RAM
281 MB Inactive RAM
661 MB Wired RAM
355 MB Page-ins
0 B Page-outs -
Using Photoshop CS6 and after printing approx. 10 cards on an Epson R3000 printer the program gives me a dialog box saying "There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopened any documents." Even after closing and reopening the program, the print command is greyed out so I cannot select any printer. This also happens with a Brother laser printer. Both printers will produce a test page out side of the Adobe product. Help!
I cannot get any help either. I get the message "There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopened any documents." I have reinstalled all drivers, powered off/on all printers (2 of them - a Brother HL - 4040cn and an Epson Stylus Pro 7890 - which all worked fine until this morning). There appears to be no path to a solution. I have read all the forums and tried about 20 different suggestions all to no avail. Reboots, changing cables, reinstalling printers and drivers and Photoshop CS6 - ALL TO NO AVAIL. On a macbook pro retina with 10.10.3. This issue is out there and some get solutions - but not all - that's my crowd...the not all crowd. I have yet to be able to print from CS6 any more. This is a show stopper and my patience is wearing thin. And I'm tired of stupid questions like "is your printer powered on?" give me a break. This appears to be an adobe photoshop cs6 problem - as I can print from every other application. Anyone have any ideas? Adobe should have something?... Adobe system info below:
Adobe Photoshop Version: 13.0 (13.0 20120315.r.428 2012/03/15:21:00:00) x64
Operating System: Mac OS 10.10.3
System architecture: Intel CPU Family:6, Model:58, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 2300 MHz
Built-in memory: 8192 MB
Free memory: 4665 MB
Memory available to Photoshop: 7059 MB
Memory used by Photoshop: 70 %
Image tile size: 1024K
Image cache levels: 4
OpenGL Drawing: Enabled.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
OpenGL Allow Old GPUs: Not Detected.
OpenGL Version: 2.1 NVIDIA-10.2.7 310.41.25f01
OpenCL Version:
Video Card Vendor: NVIDIA Corporation
Video Card Renderer: NVIDIA GeForce GT 650M OpenGL Engine
Display: 2
Display Depth:= 32
Display Bounds:= top: 1072, left: 140, bottom: 1950, right: 1580
Video Renderer ID: 16918311
Video Card Memory: 1024 MB
Video Rect Texture Size: 16384
OpenGL Version: 2.1 NVIDIA-10.2.7 310.41.25f01
OpenCL Version: 1.2 (Feb 27 2015 01:29:10)
Video Card Vendor: NVIDIA Corporation
Video Card Renderer: NVIDIA GeForce GT 650M OpenGL Engine
Display: 1
Main Display
Display Depth:= 32
Display Bounds:= top: 0, left: 0, bottom: 1050, right: 1680
Video Renderer ID: 16918311
Video Card Memory: 1024 MB
Video Rect Texture Size: 16384
Serial number: 92629107631240972642
Application folder: KerrysHD:Applications:Adobe Photoshop CS6:
Photoshop scratch has async I/O enabled
Scratch volume(s):
KerrysHD, 232.6G, 19.7G free
Required Plug-ins folder: KerrysHD:Applications:Adobe Photoshop CS6:Adobe Photoshop CS6.app:Contents:Required:
Primary Plug-ins folder: KerrysHD:Applications:Adobe Photoshop CS6:Plug-ins:
Additional Plug-ins folder: not set
Installed components:
adbeape.framework adbeape 3.3.8.19346 66.1025012
AdbeScriptUIFlex.framework AdbeScriptUIFlex 6.2.29.18602 66.490082
adobe_caps.framework adobe_caps 6.0.29.0 1.276181
AdobeACE.framework AdobeACE 2.19.18.19243 66.492997
AdobeAGM.framework AdobeAGM 4.26.17.19243 66.492997
AdobeAXE8SharedExpat.framework AdobeAXE8SharedExpat 3.7.101.18636 66.26830
AdobeAXEDOMCore.framework AdobeAXEDOMCore 3.7.101.18636 66.26830
AdobeBIB.framework AdobeBIB 1.2.02.19243 66.492997
AdobeBIBUtils.framework AdobeBIBUtils 1.1.01 66.492997
AdobeCoolType.framework AdobeCoolType 5.10.31.19243 66.492997
AdobeCrashReporter.framework.framework AdobeCrashReporter 6.0.20120201
AdobeExtendScript.framework AdobeExtendScript 4.2.12.18602 66.490082
AdobeJP2K.framework AdobeJP2K 2.0.0.18562 66.236923
AdobeLinguistic.framework 17206
AdobeMPS.framework AdobeMPS 5.8.0.19463 66.495174
AdobeOwl.framework AdobeOwl 4.0.93 66.496052
AdobePDFL.framework AdobePDFL 10.0.1.18562 66.419471
AdobePDFSettings.framework AdobePDFSettings 1.4
AdobePIP.framework AdobePIP 6.0.0.1654
AdobeScCore.framework AdobeScCore 4.2.12.18602 66.490082
AdobeUpdater.framework AdobeUpdater 6.0.0.1452 "52.338651"
AdobeXMP.framework AdobeXMPCore 66.145661 66.145661
AdobeXMPFiles.framework AdobeXMPFiles 66.145661 66.145661
AdobeXMPScript.framework AdobeXMPScript 66.145661 66.145661
ahclient.framework ahclient 1.7.0.56
aif_core.framework AdobeAIF 3.0.00 62.490293
aif_ocl.framework AdobeAIF 3.0.00 62.490293
aif_ogl.framework AdobeAIF 3.0.00 62.490293
AlignmentLib.framework xcode 1.0.0.1
amtlib.framework amtlib 6.0.0.75
boost_date_time.framework boost_date_time 6.0.0.0
boost_signals.framework boost_signals 6.0.0.0
boost_system.framework boost_system 6.0.0.0
boost_threads.framework boost_threads 6.0.0.0
Cg.framework NVIDIA Cg
CIT.framework CIT 2.0.5.19287 145486
data_flow.framework AdobeAIF 3.0.00 62.490293
dvaaudiodevice.framework dvaaudiodevice 6.0.0.0
dvacore.framework dvacore 6.0.0.0
dvamarshal.framework dvamarshal 6.0.0.0
dvamediatypes.framework dvamediatypes 6.0.0.0
dvaplayer.framework dvaplayer 6.0.0.0
dvatransport.framework dvatransport 6.0.0.0
dvaunittesting.framework dvaunittesting 6.0.0.0
dynamiclink.framework dynamiclink 6.0.0.0
FileInfo.framework FileInfo 66.145433 66.145433
filter_graph.framework AdobeAIF 3.0.00 62.490293
hydra_filters.framework AdobeAIF 3.0.00 62.490293
ICUConverter.framework ICUConverter 3.61 "gtlib_3.0" "." "16615"
ICUData.framework ICUData 3.61 "gtlib_3.0" "." "16615"
image_compiler.framework AdobeAIF 3.0.00 62.490293
image_flow.framework AdobeAIF 3.0.00 62.490293
image_runtime.framework AdobeAIF 3.0.00 62.490293
LogSession.framework LogSession 2.1.2.1652
mediacoreif.framework mediacoreif 6.0.0.0
PlugPlug.framework PlugPlug 3.0.0.383
UpdaterNotifications.framework UpdaterNotifications 6.0.0.24 "6.0.0.24"
wrservices.framework
Optional and third party plug-ins: NONE
Plug-ins that failed to load: NONE
Flash:
Mini Bridge
Kuler
Installed TWAIN devices: NONE
Maybe you are looking for
-
Safari keeps crashing on my macbook pro HELP!
this shows up as the report. i have loaded it in safe mode, restarted my computer countless times and i have no idea what else to do! please help! Process: Safari [146] Path: /Applications/Safari.app/Contents/MacOS/Safari Identifie
-
Hi. We have to send an external email in HTML format. The email can also have a logo/photo. How can we achieve this? Also, if it is possible to achieve this, can this be done in backgound also? We are not displaying when user runs the report. Only se
-
Hello! I have an app with some states. Each state shows a different custom component. My problem is that if someone types somthing in one of the states then changes state and then comes back the text will still be there. Is there a way to reintitiali
-
Unix Executable Files and VLC index.dat file -Samsung Digimax S800
Hi and thanks for any enlightenment in advance . I got my new iMac in January and it's great . I'm using it mostly for games iWeb and pro apps like Logic . I continue to use my trusty old eMac for email and internet chores . I was preparing to instal
-
Could anyone help, suddenly my contacts have disappeared, or at least I cannot access them anymore, al I have is a GROUPS screen with All Contacts underneath and...nothing else, it says no contacts...how can I find them again? Help