Failed to acquire a wave using ivi dmm step with a FlexDMM NI-4070

I tried to acquire wave with a FlexDMM NI_4070 and a Read Multipoint ivi step from TestStand, it didn't went thru. Configuration step is: DC volts, 0.01 resolution, immediate trigger source, auto once range mode, 0 trigger delay, 100 multipiont sample count, 10 sample interval, 1 trigger count, interval sample trigger, none meas complete dest; Read step is: wave data type, Step.Result.Reading meas dest, 5000 time out, "failed" status on time out. What I get is failed status due time out.

Try setting your Timeout to 30000. The Timeout is in milliseconds, while the Sample Interval on the Advanced tab of the Configure step is in seconds. You have this interval set to 10. Setting your timeout to 30 seconds will give your Read operation time to complete.
Regards,
Eric M.

Similar Messages

Teststand 4.0 IVI-DMM Step error

I have Teststand 3.5 and 4.0 installed on a computer and a NI-4060 in a PXI chassis. When I try running a sequence that has an IVI-DMM step in it in 3.5 everything runs fine. When I try the same sequence opened in 4.0 it gives me the following attached error (both attachments are the same error one is just scrolled down so you can see the whole thing.) I have tried adding a simple IVI step from scratch in teststand 4.0 and I get the same error.
Any ideas?
Brian
Attachments:
untitled1.JPG ‏107 KB
untitled2.JPG ‏106 KB

Ok, I used the version selector, went back to 3.5, and ran the sequence and it ran fine like I expected. When I switch back to 4.0 and ran it it worked (first time in a dozen tries.) So I switched back to 3.5 ran it and then ran it 4.0 again and it failed. I attached a spy capture from 3.5, 4.0 worked, and 4.0 didnt work.
Brian
Attachments:
DMMConfig_TS40_Capture_Didnt_Work.spy ‏1 KB
DMMConfig_TS35_Capture.spy ‏11 KB
DMMConfig_TS40_Capture_Worked.spy ‏12 KB

IVI DMM step won't connect

When I try to connect my IVI DMM Acquire step to a 34411A, I get the following error:
ivi_IviDmm Configure Power Line Frequency [PLF].vi<ERR>
Primary Error: (Hex 0xBFFA0011) Does not support this class-compliant feature: method %1
Elaboration: FunctionId: 69, FunctionName: ConfigurePowerLineFrequency
<b>Complete call chain:</b>
ivi_IviDmm Configure Power Line Frequency [PLF].vi
ivi_subDMMPreExecute.vi
ivi_InstrDMMBlockState.vi:1
I'm guessing that the IVI Dmm Acquire step is attempting to call the IVI 'ConfigurePowerLineFrequency' function, which is (apparently) not supported by the 34411A driver. Is there any way to work around this?
Thanks,
Aaron

Hi Aaron,
I currently have not found any resources that allow SignalExpress to ignore initialization errors. However I did find a resource that has the command for the power line frequency for your device (page 8). http://www.home.agilent.com/upload/cmc_upload/All/34410A_Quick_Reference.pdf?&cc=US&lc=eng
You can modify the 34411A library so that this command is not used during your IVI DMM Acquire Step; however, I was unable to find the subDMMPreExecute.vi in a search of the project.
Sam B.
Applications Engineer
National Instruments

Using Offset Compensated Ohms from IVI DMM in TestStand

I am using TestStand 3.5 with a PXI-4070 DMM and I want to be able to use the Offset Compensated Ohms function from the TestStand IVI-C DMM steps. I cannot find this functionality from the TestStand step, even though it is shown on the front panel of the Soft Front Panel DMM, and is stated as a IVI function.
Anybody with any ideas would be greatly appreciated.
A.

Good afternoon A,
The Offset Compensated Ohms function that you are looking for is more
specialized than what the IVI driver has to offer. Instead of
using IVI DMM, try NI-DMM. This is a free download off our
website, which can be found here:
NI-DMM version 2.5 for Windows 2000/XP--LabVIEW Real-Time
http://digital.ni.com/softlib.nsf/websearch/1F1A167276498327862570AC005199D5
Regards,
Mike Torba
National Instruments

I want to call the DMM- SFP from Teststand using IVI

Hi I have a Teststand 3.0 system with a NI-PXI 4070, and I want to call the DMM-SFP from Teststand using the IVI driver architecture. Unfortunatley I cannot figure out how to link the DMM-SFP to the Logical name.

ADL,
If you are using the TestStand IVI step types, after you have added the logical name in MAX, you can insert an IVI DMM step type. Then right-click on the step and choose "Edit IVI Dmm". You should be able to choose from the Logical Name Ring Control the logical name you created in MAX.
If you haven't added the logical name into MAX, depending on what version of MAX you have, you can refer to Using Measurement & Automation Explorer 2.x to Configure Your IVI System or look in the IVI help that comes built into MAX 3.0.
If you checked there already or have another question, please let us know!
Regards,
Shannon R.
Applications Engineer
Nati
onal Instruments

Using IVI driver for reading delay in MSO6104A

Hi,
I have the NI IVI driver for the MSO6104A scope. The driver is functional and I manage to use it.
My scope has a function of measuring delay between two different channels. But, how can I read the Delay measurement using IVI scope step?
Is there any other way of reading this measurement?
Thanking in advance
Solved!
Go to Solution.

As far as I know, interchannel delay is not a supported IVI measurement function. So, you can complain to ivifoundation.org first of all. Or, in a code module, you can use the instrument specific driver to get the measurement. This would make the application 'non-IVI' so most of the reasons for using IVI in the first place are gone. Or, retrieve the waveforms from each channel and calculate the delay in a code module.

Error: Failed to acquire connection while exporting a file using SSIS package through SQl Server Agent job.

Hi Team,
I am running a sql server job which is loading data to a sharepoint document library.File is an excel format and is getting loaded
when executed through SSDT solution .But when i am using an SQL Agent job to pick up the file it doesnt get the path and agent job fails with the error "Failed to acquire connection".I have deployed the SSIS Package through SQL Server 2012 deployment
methodologies.
I am not able to trace the error of loading data from a sharepoint library.library. Sql agent jobs works fine when i give local path.The
account which is running the sql agent job is the same who has access to document library.I also tried to run the job through proxy account. I am using a xml configuraion to store my credentials.I am able to palce the same file to a network drive in the same
server through sql server agent job. The only problem is when I am trying to load the file to a sharepoint folder.
Thanks,
Arsa..

Is that the WebDAV method that you are suggesting here to map the n/w drive?
Its kind of webdav but you will be using windows nw drive to store data
yes, I am able to create the file to D: , but didn't check with the C:.
Try with c:, as c: require special permisssions
If this helped you resolve your issue, please mark it Answered

Agilent 34980A simulation using IVI-drivers in Teststand?

Hello! I am unable to simulate 34980A in TestStand and here are some results based on testing:
Agilent 34980A is linked to logical name SampleDmm. Simulate With: Specific Driver.
IviStepTypes.seq used with only DMM and Switch steps.
Using IviDMM IVI-C causes runtime-error in Ivi DMM Configure Single Point: Component Works IVI Control Error: The IVI Configure operation failed for logical name 'SampleDmm'. Details: Extension capability not supported by instrument driver. (Base)
Using IviDMM IVI-COM causes runtime-error in Ivi DMM Read Single Point: Component Works IVI Control Error: The IVI Read operation failed for logical name 'SampleDmm'. Details: Attribute ID not recognized. [IVI Error Code: BFFA000C] Source: TSIviStepTypes
Skipping Ivi DMM SFP -step removes that error but next one waits in Ivi DMM Configure Multi Point: Component Works IVI Control Error: The IVI Configure operation failed for logical name 'SampleDmm'. Details: Attribute or property not supported. [IVI Error Code: BFFA0012] Source: TSIviStepTypes
Skipping multi point steps helps until Ivi Switch Connect where another error hits: Component Works IVI Control Error: The Connect operation failed for logical name 'SampleDmm'. Details: No path was found between the two channels. [IVI Error Code: BFFA2011] Source: TSIviStepTypes
I find some similarities in forum post that involves HP 34401A and IVI .
According to IVI-C Class Driver Support for IVI-COM Specific Drivers the fault might be in 64 bit system (the note in the end). Is this the case? I can't use IVI-COM-drivers in 64bit system?
Example's default DMM Hewlett-Packard 34401A Digital Multimeter simulation works perfectly in unmodified example(it has IVI-C). It even shows simulated numbers in the SFP which is zero all the time with Agilent.
Has anyone succeeded to simulate 34980A properly in TestStand? Any knowledge about how to solve this thing? Any help is welcome. Thank you.
Setup:
-Teststand 5.1
-Windows 7 64bit
-IVI shared components 2.2.1
-Visa shared components 1.5 64bit
-Agilent IO libraries suite 16.3 Update 1
-Agilent 34980A IVI Driver 1.5.3
-MAX/Agilent 34980A published APIs:
-IviDmm 4.1 IVI-COM (IVI-C tried with less success)
-IviSwtch 4.0 IVI-C & IVI-COM

Some IVI drivers are designed to work in simulation mode, that is, the virtual instrument can be defined in MAX but no physical instrument is necessary to use the "instrument". If you turn off the simulate checkbox on the validate dialog box, TestStand will create the instrument session without simulation and the driver will attempt to talk to a physical instrument. If no physical instrument definition is available or if the address defined for that virtual instrument is incorrect, the above error can occur.
Scott Richardson (NI)
Scott Richardson
National Instruments

Need Help on Troubleshooting IR Error: Failed to acquire access to database

Hi there,
I have been struggling with the following error "Failed to acquire access to database" and ODBC driver error "Data source name not found and no default driver specified" when opening an IR document for a few weeks.
The IR document uses an oce file called ABC.oce and DAS has been configured accordingly.
ODBC System Data Source called ABC created on server running IR DAS as follows:
- Driver: Oracle in OraClient11g_home1
- TNS entry: ABC
- Connection tested successfully;
IR DAS entry ABC created as follows:
- Connectivity Type: ODBC
- Database Type: Oracle
- Hostname: ABC
oce file called ABC.ore created as follows:
Interactive Reporting Database Connection
Connection Software: ODBC
Database: ORA8
Host: ABC
Username and password have been entered in the oce file as well.
What possibly have I missed?
Any help will be highly appreciated.

Are you using the Hyperion ODBC drivers which comes with the Hyperion installation?

Code: 0xC0208452 Source: Data Flow Task ADO NET Destination [86] Description: ADO NET Destination has failed to acquire the connection {}. The connection may have been corrupted.

Hi There!
I have created one package (1) to import data from Flatfile(csv), (2)Clean It then (3)send clean rows to SQL Database.
This package was working fine before. Since I have decided to deploy this package to automate this process, I have no clue what went wrong but this doesn't run anymore. Flatfile and Database are on same windows box. We are running SQL 2008.I
have attached some screenshot to make this conversation more concise.
Your time and efforts will be appreciated!
Thanks,
DAP

Hi Niraj!
I recreated connection and I was able to remove that RED DOT next to those connections.
Still package doesnt run well :(
I have only one server. I use same server through out the process. I ran that process as job through SSMS and attached is output file(if this explains more)...
Microsoft (R) SQL Server Execute Package Utility
Version 10.0.4000.0 for 64-bit
Copyright (C) Microsoft Corp 1984-2005. All rights reserved.
Started: 11:34:38 AM
Error: 2014-07-18 11:34:39.33
Code: 0xC0208452
Source: Data Flow Task ADO NET Destination [86]
Description: ADO NET Destination has failed to acquire the connection {2430******}. The connection may have been corrupted.
End Error
Error: 2014-07-18 11:34:39.33
Code: 0xC0047017
Source: Data Flow Task SSIS.Pipeline
Description: component "ADO NET Destination" (86) failed validation and returned error code 0xC0208452.
End Error
Error: 2014-07-18 11:34:39.33
Code: 0xC004700C
Source: Data Flow Task SSIS.Pipeline
Description: One or more component failed validation.
End Error
Error: 2014-07-18 11:34:39.33
Code: 0xC0024107
Source: Data Flow Task
Description: There were errors during task validation.
End Error
DTExec: The package execution returned DTSER_SUCCESS (0).
Started: 11:34:38 AM
Finished: 11:34:39 AM
Elapsed: 0.531 seconds
Thanks for your time and efforts!
DAP

WARNING: Failed to acquire org.gnome.SessionManager

can't open gnome-shell(terminal)
message:
WARNING: Failed to acquire org.gnome.SessionManager
my /etc/rc.conf
DAEMONS=(dbus hal syslog-ng !network !dhcdbd !networkmanager netfs crond wicd alsa gdm)
~/.xinitrc
expor LC_CTYPE="en_US.utf8"
export XIM="ibus"
export XMODIFIERS=@im=ibus
export GTK_IM_MODULE="ibus"
export QT_TM_MODULE="ibus"
ibus &
exec ck-launch-session dbus-launch
~
Last edited by ringfin (2011-07-09 00:34:08)

get rid of hal, is not needed since gnome 2.30. it think it fails to start because of export GTK_IM_MODULE="ibus". Do not export any GTK_ since this variables are used by gtk2 and gtk3.
it will be nice to paste the whole log and not only this warning

Continuous messages *dtlArpTask: osapi_sem.c:1179 Failed to acquire ..

Client have recently upgraded from 4402 WLC to 5508. They are now receiving a large number (100 000s a day) of warnings. Software Version is
7.5.102.0
2013-09-09 00:00:02 Local0.Warning 10.61.183.17 ausowlc1: *rmgrMain: Sep 09 00:00:02.769: #OSAPI-4-MUTEX_LOCK_FAILED: osapi_sem.c:1179 Failed to acquire a mutual exclusion object. invalid(NULL) pointer passed.
I have found related bug CSCui55350/ CSCuh41790
CSCui55350/ CSCuh41790
Continuous messages *dtlArpTask: osapi_sem.c:1179 Failed to acquire ..
Symptom:
Continuous messages:
-Traceback: 0x10c31374 0x10c8a6a4 0x10c9ea08 0x10c94748 0x10c402d8 0x12283850 0x122f634c
*rmgrMain: Aug 08 09:49:21.902: #OSAPI-5-MUTEX_UNLOCK_FAILED: osapi_sem.c:1036 Failed to release a mutual exclusion object. invalid(NULL) pointer passed.
-Traceback: 0x10c30d9c 0x10c8a7f4 0x10c9ecf8 0x10c95d4c 0x10c402d8 0x12283850 0x122f634c
*rmgrMain: Aug 08 09:49:21.902: #OSAPI-4-MUTEX_LOCK_FAILED: osapi_sem.c:1179 Failed to acquire a mutual exclusion object. invalid(NULL) pointer... more
Conditions:
AP in flex mode, 7.5 in use
Workaround:
None
Further Problem Description:
Details:
Known Affected Releases: (3)
7.5(102.0) | 7.5(1.69) | 7.4(100.0)
Known Fixed Releases: 0
Release Pending
Product: Cisco 5500 Series Wireless Controllers
Status of this bug is fixed but known fixed releases are 0. Please advise if this software bug and/or hardware failure and what is best workaround ?
Any help would be appreciated.

Hi Michael,
This error is seen due to a setting the dev team has disabled on the WLC and are expected to be fixed in 7.6. These messages are just cosmetic and have no impact.
Workaround at this point is :
These are warning messages displayed on the console. Instead of enabling warnings, errors can be enabled. So that it does not flood the console.
Kunal

Error : MDSConfig failed to acquire write lock??

Hi,
Changes that I know used to flow, don't flow anymore, and I was suspecting something was wrong with the changelog followup.
I guess I was right, cause I see this in the meta-.xxx.log:
MDSConfig failed to acquire write lock 'MDS_E_FAILED_TO_ACQUIRE_WRITE_LOCK' (80042212), wlock=(fe3f1c40), rlock
=(fe3f1c10), readlocks=4, writelockstate=0
No mention in the admin guide obvioiusly.
Anyone knows what this might mean? The config is on a dedicated DS instance, and no errors found there.
MDS = 5.0SP1
DS = 5.1SP1
Thanks,
Wim

i sometimes see such messages on startup
normally they go away a few minutes later.
another solution is to stop everything (meta directory processes, and the LDAP's containing the MV and the NetscapeRoot), then start only the LDAP's, wait a few minutes, start the join-engine,
it seems some objects in the ldap still/already have a write lock on them (myabe from a previous connection), when the join-engine tries to write to them

NI-DMM vs. IVI-DMM - Soft Front Panel

Hello All,
I have been developing a testing application that will eventually use a PXI-4070 DMM (currently simulating it in NI MAX). I had been using the IVI DMM functions, but ran into a problem when I couldn't do a diode test (diode test is apparently not officially standardized by IVI yet). So I switched to using the NI-DMM functions. For the most part, it was a pretty seamless transition, but there is one thing I have not been able to replicate with the NI-DMM simulation that I could do with the IVI-DMM. When I used the IVI-DMM functions, and ran the VI, a popup opened that allowed me to enter in the simulated value that I wanted the DMM to read. I can't get this to work with the NI-DMM functions. Is it possible? If so please let me know how to activate. Thanks.
GSinMN
Solved!
Go to Solution.

The advanced simulation exists only on the IVI class driver level (IviDmm). The IVI class drivers implement simulation features by using simulation drivers. The IVI Compliance Package (ICP) installs a simulation driver for each IVI class driver. Each simulation driver plugs in to the corresponding class driver and performs flexible output data simulation. The NI-DMM driver is a specific driver that supports series of NI DMMs, and therefore does not include the advanced simulation feature.

Failed to acquire DAS with data sources that match the specified OCE

Please help, Thank you all.
We are migrating Oracle databases from Windows to Linux servers. Currently, I have no problem to use my desktop Hyperion Intelligence Designer 8.5 with new oce file to connect to Linux. However, I published the same oce file to Hyperion Performance Suite 8.5 then I got “Sever Error [2018]: Failed to acquire Data Access Service with data sources that match the specified OCE”.
I launched Service Configurator, in the “Local Service Configurator - DAS1_host”, the “Database JDBC URL is point to Linux server. Also, I added ODBC connection to Oracle database on Linux in the “Properties of Data Access Service: DAS1_host’s Data Source”. Database of JDBC URL in BI1_host, AZ1_host, PUB1_host, SM1_host, LS1_host, UT1_host, BPS1_host, AN1_host are also point to Linux server.
The “Remote Service Configurator” has ES1_host’s” Storage” with JDBC URL point to Linux server. The same for RM1_host’s and NS1_host’s “Storage” with JDBC URL point to Linux server.
Is there some missing configuration on the server? Thank you in advance.

You should login to my oracle support to look into this ID.
This is the solution mentioned
Solution
1) In the .profile file, you will find the definition of the LD_LIBRARY_PATH variable. However, the path to 64 bit libraries is probably appended before the path to the 32 bit libraries(%ORACLE_HOME%/lib32). Therefore, please reverse the order in the definition so that the 32 bit libraries get loaded before the 64 bit libraries.
Then, restart all services.
2) Oracle 9.2 was the first Oracle release which defaults to using the 64 bit libraries in the 'lib' directory and the 32-bit libraries that we need are in the 'lib32' directory.
Therefore, please have the%ORACLE_HOME%/lib32 placed in front of the LD_LIBRARY_PATH environment variable definition.Then, restart all services.
3) Please check that users have read and write access to the files located in the %ORACLE_HOME%/lib32 folder.
4) Check the permissions of the libclntsh.a file(located in the %ORACLE_HOME%/lib32 folder) are set to rwxr-xr-x
5) Recreate the OCE connection in DAS and restart DAS in CMC.
6) Restart all the BIPlus Services and process the query.

Failed to acquire a wave using ivi dmm step with a FlexDMM NI-4070

Similar Messages

Maybe you are looking for