Fails to Recognize Symantec Update

I am a college student (junior) who is required to run Cisco Clean Access Agent and Symantec. For the past two years, it seems Cisco does not recognize the update Symantec downloads. Every week, when I have to re-log into Cisco, I get the following error message: "Your system does not meet the requirements enforced by the network administrator. If you have already followed the instructions and finished the update, the process might have failed. The failure may have been caused by no network access to the update site"
The only solution I have found is to Ghost my computer back to virgin and start over. This includes two years of Windows updates and reinstalling all of my software which is a VERY time consuming endeavor as you can imagine.
My tech support here is clueless and I cannot keep spending an entire day to fix this problem.
If anyone has ANY clue what is going on and/or how to fix it, it would be most appreciated.
Thanks.

CCA does check the installation of AV through the combination of registry keys. If the registry keys are missing or some undesirable value is modified, CCA will treat it as an improper installation. You should try unistalling and then reinstalling the AV. Also CCA does not recognizes Symantec AV versions less than 9.x. If you AV version is less than 9.x upgrade your AV to 9.x version.

Similar Messages

Android Update -- now fails to recognize SD Card!

Android did an automatic update yesterday, and suddenly failed to recognize the SD Card. It keeps telling me the card has been removed and that I need to insert a new one.
This device has been rebooted, cache cleared, card viability verified. What gives?

Hi dont-have-time-for-this,
SD card issues are no fun, I feel you! I also have a Galaxy S3 and when I received my software update I did a factory reset http://bit.ly/LfV00q after installation to prevent any system conflicts and post update issues, and I have not experienced any issues with my SD card. Try it and keep us posted.
AntonioC_VZWSupport
Follow us on Twitter at www.twitter.com/VZWSupport

W500 w/ Windows 7 64-Bit Ultimate fails to recognize some audio CDs

My DVD/CD drive (a HL-DT-ST_DVDRAM_GSA-U20N) in my Lenovo W500 laptop (running Windows 7 64-Bit Ultimate) fails to recognize some audio CDs.
It recognizes most audio CDs, but a few are not recognized by Windows 7 itself, or by any other program on my computer.
These CDs are recognized by other Windows 7 computers.
I don't think that it's a copy protection issue, since the CDs don't mention any copy protection scheme (and also since they work on other Windows 7 machines).
One CD that wasn't recognized by my machine was the second CD from a two CD set (the first CD was correctly recognized).
I have the latest updates for Windows, and all my programs, drivers, BIOS & firmware.
Thanks.

What kind of behavior are you getting from the drive? If it's spinning up, down, and up again your lens might be dirty or the drive could be failing.
If you do clean the lens, be careful. Do your research first or you might make it worse.
Edit: Replacements are:
42T2511 or 42T2541 (DVD)
42T2543 or 42T2513 (DVD/CD-RW combo)
42T2545, 42T2515 or 42T2551 (DVD-RAM/RW)
You can get the 42T2543 for $23 and the 42T2545 for $45 on eBay.

The server is failing to download some updates. Event ID 10032 (ran out of disk space & extended volume, still got error)

On Friday, 9/17 @ 7 am, after deselecting Windows 2003 in products, I ran Server Cleanup Wizard (as well as sqlcmd -I -i"WsusDBMaintenance.sql" -S "np:\\.\pipe\MSSQL$MICROSOFT##SSEE\sql\query"), and 0 bytes were freed which I thought
odd.   I then selected Windows Server 2012 R2 and Office 2013 since we're going to be using those.
After this, on 9/19 @ 7:30am, the server had the message:      Event 364 Content file download failed. Reason: There is not enough space on the disk.    Source File: /d/msdownload/update/software/secu/2014/04/coreservermui-it-it_ebb7e1e8d487b90ffd719f06122a3db947b3f949.cab
Destination File: e:\WSUS\WsusContent\49\EBB7E1E8D487B90FFD719F06122A3DB947B3F949.cab.
At some time during the day on 9/19, our SAN admin increased the volume (all server's volumes are on a SAN) from the SAN end, and I extended it in Disk Mngmt on the WSUS server.   I went home for the weekend
I came back today (9/22), saw I had gotten the "the server is failing to download some updates. Event ID 10032"   on Saturday 9/20 @ 1:30am.   I checked the volume \WSUScontent is on (the volume we extended) and it has
17GB free. So I assume space should not still be an issue.
The same 10032 error had occurred on 9/19, at 1:30 pm, but I assume it was before my colleague and I bumped up the disk space. But why it occurred again the next day I'm not sure.
However, since the 10032 error on 9/20 @ 1:30am, it has not reoccured, and no yellow or red event messages. So possibly all is well now. Could it have been that WSUS was being sluggish to recognize the increased disk space, even though Windows
itself recognized it?

Thanks Lawrence, I went through the steps you instruct on (which I did not know about, so I greatly appreciate that!), and freed up over 30GB of space.
Outstanding! :-)
But your steps don't really address deleting all (solely) 2003 updates.
Correct. First, because you cannot DELETE updates, unless they are expired or old revisions, and use the Server Cleanup Wizard to do that.
Second, because the article was about removing *unneeded* updates. It does not consider the scenario where a product category is being retired
When I go to my "2003" update view, sorting by Any Except Declined, and Status Any, I still see tons of 2003 ones, some solely for it, others that apply to 2003 and other OSs. I want to leave the latter, but delete the ones solely for
2003. Not just superseded ones, but ALL that are solely for 2003.
You cannot delete updates. You can DECLINE updates, if that's what you want to do.
So let's talk a minute about these updates that might be applicable to operating systems other than Windows Server 2003. Let's be practical about the other operating systems listed. If you look closely, I suspect you will discover that those "other
operating systems" are either Windows XP or Windows 2000, but nothing else. Do updates for Windows XP or Windows 2000 really matter to you? I suspect not.
The reason I highly suspect this is because the practice of building packages targeted at multiple operating systems was terminated when Windows Vista was released (actually I think it happened with the release of WSUS v3, but this is just a matter of trivia,
the relevant point is that it's not done anymore, and has not been done for many years).
Ergo, I know for a fact, that NONE of the updates applicable for Windows Server 2003, will be applicable for any newer operating system. Ergo, it probably doesn't matter at all, so just SelectAll -> Decline if that's what you want to do.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

I iPad 3 fails to recognize cellular data In a number of locations Displays "searching and No Service" I have narrowed this to device problem. What can I do?

i iPad 3 fails to recognize cellular data In a number of locations Displays "searching and No Service" I have narrowed this to device problem. What can I do?

Hello there, OSOSANYA.
The following Knowledge Base article provides a great checklist of steps and additional recommendations for troubleshooting issues with cellular connection:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Follow these steps for help troubleshooting cellular data issues on your iPhone. After performing each step, please test to see if the issue is resolved.
Toggle airplane mode: Tap Settings, turn airplane mode on, wait three seconds, and then turn off again.
Restart your iPhone.
Make sure that your software is up to date:
Check for a Carrier Settings Update: Tap Settings > General > About.
Check for an iOS Software Update: Tap Settings > General > Software Update.
Note: Some updates may require a Wi-Fi connection.
Remove the SIM Card and reinsert it. Allow the iPhone to acquire the network again.
If your SIM card has SIM PIN enabled, try turning it off: Tap Settings > Phone > SIM PIN.
Try another location. If a different location works, but the original location still doesn't, contact your carrier to report the issue.
Reset network settings: Tap Settings > General > Reset > Reset Network Settings.
Restore the iPhone as new.
Contact your carrier to:
Verify that the iPhone is properly set up on the account with the appropriate, current data plan.
Verify that there are no account-related blocks.
Find out if there are specific error messages in the carrier logs that could help determine why the issue is occurring.
If none of the above steps resolves the issue, contact your carrier, make an appointment at an Apple Retail Store, or contact AppleCare to troubleshoot further.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Windows Update failed to check for updates with error 0x800B0001

Hi all,
I have a WSUS installed on a Windows Server 2008 R2 box, I have a new Windows Server 2012 box (joined to domain) that cannot get updates from the WSUS, whenever I try to search for new updates I receive the following error in event viewer:
Windows Update failed to check for updates with error 0x800B0001
Note: I cannot see the Win2K12 server in the WSUS console under computers node.

I couldn't get it to run even after installing the mentioned KB fixes. So I investigated the error myself, and found a "hack" that seems to fix the issue. Wrote up a small piece on it here:
http://tplive.azurewebsites.net/2013/12/windows-update-error/
You and about a thousand other people have reported "I had already installed [the update], but installing it AGAIN fixed the problem.", which is almost assuredly a simple indication that the original installation of the update failed, and you simply did
not recognize that the installation of the update was not successful.
The fact that the /selfupdate folder was corrupted (read: missing files) pretty much says it all. There's no bug. Your installation of the update simply failed. (Or, the server wasn't healthy to begin with and you got what you got.)
Bottom line: The only known cause for a client-side 0x800B0001 error code is that the WSUS server has not been
properly and completely patched.
Lawrence Garvin, M.S., MCITP:EA, MCDBA, MCSA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2013)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence R Garvin
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Superdrive Sometimes Failing to Recognize DVDs

I've had my MacBook Pro for about 15 months and the Superdrive is now sometimes failing to recognize blank media, or ejecting commercial DVD's after playing the movie for a few minutes. Obviously the warranty has expired and I'm thinking of buying an external drive if the problem can't be fixed inexpensively. Any suggestions as to how to resolve this problem?
Thanks in advance.

Yes, I am having same problem. After updating to OS 10.5.2, my SuperDrive in my MacBook 2.2 GHz Intel Core 2 Duo will not play any DVD or Enhanced CD. (It will play audio CDs.)
For me, this is DEFINITELY an Apple software/firmware issue. When a DVD wouldn't play in my MacBook SuperDrive, I would instead use my MacMini successfully, which was running OS 10.4.x. I recently updated the MacMini by cloning my MacBook to it, and viola, succeeded in replicating the exact problem.
Also curious, my MacBook SuperDrive almost worked the first time I put my first DVD into it. DVD Player asked to set the region, which I did. It then refused to play the DVD or any other media DVD/CD subsequently.
I have no solution yet, but will share with all when I do.

Firefox/Safari Fails to Recognize iSight

I have attempted using my webcam over the internet programs and it fails to recognize that I have a built in camera. The main places this occurs are Facebook and Chatroulette. How would this be fixed?

db92 wrote:
I have attempted using my webcam over the internet programs and it fails to recognize that I have a built in camera. The main places this occurs are Facebook and Chatroulette. How would this be fixed?
Several 10.6.5 users are currently finding problems with Flash based video web sites, perhaps due to timing differences in the various update cycles of the developers.
Therefore, check all third-party items like Flip4Mac, Safari "Extensions", web-based chat items, social web site "toolbars", etc., to be sure you are using the latest versions compatible with your system's versions of OS X and browser. Uninstall any with known issues pending their next update.
If you are still having iSight problems ONLY on Flash-based web sites, here are some things you can try. Depending on system configuration and installed third-party items, various users have reported different methods of restoring Flash video website functionality. Which might work for you seems to be a matter of what you have added to your system, so keep trying any relevant to your system until you find the one that might work for you.
(1) For those who have installed Google plugins, user OysterOyster reports that uninstalling them restores proper iSight function with Flash and Mac OS X 10.6.5.
If Google is your problem, the GoogleVoiceAndVideoUninstaller.app should be in your hard drive's Library/Application Support/Google/ folder. (not your *Home > Library* folder)
Several users confirm that using the Google uninstaller works to restore Flash video functions.
Some other users, including those who do not use the Google plugins, have found other remedies.
(2) User joew13 reports that installing the 64-bit Flash plug-in beta for Mac OS X (DMG, 8.7 MB) fixed Flash sites for him.
This link allows download of the 64-bit plugin beta from an official Adobe page:
http://labs.adobe.com/downloads/flashplayer10.html
or, to download the beta directly, click this link--> http://tinyurl.com/2frejs4
Several other users have confirmed success after the beta update.
(3) User imagerle downgraded Flash to version 10,0,45,2 to restore Flash video.
If this older version is not available on a backup or an old install disk, it can be downloaded from Adobe's Archived Flash Players page:
http://kb2.adobe.com/cps/142/tn_14266.html
(4) User sirjoe82 and others have reported that uninstalling Flip4Mac restored their Flash video website functions.
Message was edited by: EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.5); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.5)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod4touch4.2.1

HT6437 iTunes fails to recognize iPhone

I am attempting to backup/restore my iPhone 4S running iOS 7.1.2, to my new iPhone 6 Plus running iOS8.1.2.
Unfortunately, iTunes 12 fails to recognize my iPhone device. Therefore, it's impossible to Backup or Synch.
Any ideas to correct this? Do I have to update my ancient iPhone 4S to iOS 8.1.2 first? I tried different USB cables, no luck. I tried stop/re-start iTunes.

Hello there, dpharbison.
When transferring content from an older iOS device to a new one using iTunes, the following Knowledge Base article offers the steps on how to accomplish that:
Transfer content from an iPhone, iPad, or iPod touch to a new device - Apple Support
Use iTunes
If you don't have an iCloud account or you just want to keep a backup on your computer, you can use iTunes to back up and transfer content on your device.
Get ready
Install the latest version of iTunes on your computer and the latest version of iOS on your original device.
You can't install a backup of a newer version of iOS onto devices that are using earlier versions of iOS. If your backup came from a device that has a newer version of iOS installed, update your new device before you transfer your data. For help, see Unable to restore from a backup of a newer iOS device.
Back up and transfer
First, back up your old device using iTunes. You can also encrypt the backup so that it remembers the passwords for your email, Wi-Fi, and more when you transfer to the new device. Otherwise, you can re-enter these passwords on the new device.
Then transfer your data from your device to your computer.
Remove your SIM card
If your device has a SIM card, use the SIM-extractor tool or a paper clip to remove the SIM from your old device and insert it into your new device. Or if your carrier gave you a new SIM card, use that instead.
Set up the new device
When the backup of your old device is finished, turn on your new device. Follow the setup assistant, which will ask you to choose these things:
Your language and country
Whether to enable Location Services
A Wi-Fi network
If you don’t have a Wi-Fi or cellular data connection, you can also activate by tapping Connect to iTunes.
Restore the backup
When prompted to set up your device, select Restore from iTunes Backup.
Connect to iTunes
Connect your new device to iTunes, using the same computer you used to back up your current device. iTunes will ask you to restore from backup or set up as new. Select the backup of your old device and choose Continue.
If the progress bar in iTunes pauses for a while, wait until the restore finishes.
Sync other content
When the restore finishes, your device restarts, and then it's ready for you to use.
Keep your device connected to iTunes to sync content that isn't in the backup (such as music, videos, and apps). To change the type of content that syncs, click the syncing tabs in iTunes.
Enter your passwords
If you restored from an unencrypted backup, you'll need to enter the password for your Apple ID, email and other accounts, and voicemail. If you've forgotten your voicemail password, contact your carrier.
If your device continues to not be recognized, these article provide further troubleshooting depending on the operating system your computer is running:
iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
or
iOS: Device not recognized in iTunes for OS X - Apple Support
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Remote Update Manager doesn't recognize applicable updates

Hi,
We have a script scheduled to run Remote Update Manager on one of our client machines. This machine is currently running OSX 10.8.5 and Adobe Creative Cloud. When looking at Creative Cloud directly, we can clearly see that there are updates available for our Adobe products. Remote Update Manager, however, does not recognize these updates and will therefore not automatically update. This prevents the user from working as they do not have access to administrative credentials used to update these applications.
I have included an example of the returned messages by Remote Update Manager. These logs are pulled as of this morning but, as you can see, still reflect an outdated entry of 10/17/13.
| UpdaterCore library initialized successfully.
10/17/13 09:48:24:600 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | **************************************************
10/17/13 09:48:24:600 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | Starting UpdaterCore CheckForUpdate...
10/17/13 09:48:25:186 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | CheckForUpdates completed successfully.
10/17/13 09:48:25:186 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | **************************************************
10/17/13 09:48:25:186 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | Starting UpdaterCore DownloadUpdates...
10/17/13 09:48:25:188 | [WARN] | | AAMEE | Utilities | RemoteUpdateManager | | | No new applicable Updates. Seems like all products are up-to-date.
10/17/13 09:48:25:188 | [INFO] | | AAMEE | Utilities | RemoteUpdateManager | | | **************************************************
10/17/13 09:48:25:189 |
I was wondering if you had any advice on the next steps to resolve.
Thanks,
Evan

Some links that may help
-Team Installer http://forums.adobe.com/thread/1363686?tstart=0
-http://helpx.adobe.com/creative-cloud/packager.html
http://forums.adobe.com/community/download_install_setup/creative_suite_enterprise_deploym ent

Software Updates ADR Issue: "Failed to download the update from the internet. Error = 5"

"Failed to download the update from internet. Error = 5"
The above is the error I am getting when running any ADR. The error is quite clear software updates are failing to download and Error = 5 being a permissions error its clear that the downloads are failing due to incorrect permissions applied to the download
path.
Here is the last bit of my ruleengine.log, everything above is the same except for the update trying to be downloaded of course:
Failed to download the update from internet. Error = 5
SMS_RULE_ENGINE 6/26/2014 9:21:59 AM
5148 (0x141C)
Failed to download ContentID 16860969 for UpdateID 16857152. Error code = 5
SMS_RULE_ENGINE 6/26/2014 9:21:59 AM
5148 (0x141C)
Downloading contents (count = 1) for UpdateID 16857255
SMS_RULE_ENGINE 6/26/2014 9:21:59 AM
5148 (0x141C)
List of update content(s) which match the content rule criteria = {16861141}
SMS_RULE_ENGINE 6/26/2014 9:21:59 AM
5148 (0x141C)
Downloading content with ID 16861141 in the package
SMS_RULE_ENGINE 6/26/2014 9:21:59 AM
5148 (0x141C)
Failed to download the update from internet. Error = 5
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Failed to download ContentID 16861141 for UpdateID 16857255. Error code = 5
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Failed to download any update SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Failed to download update contents. SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
No new update was added to the package. Package "SCP0008A" would not be updated.
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Failed to run the DownloadAction for the AutoDeployment.
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
STATMSG: ID=8706 SEV=E LEV=M SOURCE="SMS Server" COMP="SMS_RULE_ENGINE" SYS=SCCM-MPS.DSCICORP.COM SITE=SCP PID=2376 TID=5148 GMTDATE=Thu Jun 26 13:22:00.164 2014 ISTR0="SMS Rule Engine" ISTR1="Failed to download one or more
content files" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Enforcing Create Deployment Action SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Create Deployment Rule Action XML is: <DeploymentCreationActionXML xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"><CollectionId>SCP00055</CollectionId><IncludeSub>true</IncludeSub><Utc>false</Utc><Duration>0</Duration><DurationUnits>Hours</DurationUnits><AvailableDeltaDuration>0</AvailableDeltaDuration><AvailableDeltaDurationUnits>Hours</AvailableDeltaDurationUnits><SuppressServers>Checked</SuppressServers><SuppressWorkstations>Unchecked</SuppressWorkstations><PersistOnWriteFilterDevices>Unchecked</PersistOnWriteFilterDevices><AllowRestart>true</AllowRestart><DisableMomAlert>false</DisableMomAlert><GenerateMomAlert>false</GenerateMomAlert><UseRemoteDP>true</UseRemoteDP><UseUnprotectedDP>true</UseUnprotectedDP><UseBranchCache>true</UseBranchCache><EnableDeployment>true</EnableDeployment><EnableWakeOnLan>true</EnableWakeOnLan><AllowDownloadOutSW>false</AllowDownloadOutSW><AllowInstallOutSW>true</AllowInstallOutSW><EnableAlert>true</EnableAlert><AlertThresholdPercentage>90</AlertThresholdPercentage><AlertDuration>7</AlertDuration><AlertDurationUnits>Days</AlertDurationUnits><EnableNAPEnforcement>false</EnableNAPEnforcement><UserNotificationOption>DisplaySoftwareCenterOnly</UserNotificationOption><LimitStateMessageVerbosity>false</LimitStateMessageVerbosity><StateMessageVerbosity>10</StateMessageVerbosity><AllowWUMU>true</AllowWUMU><AllowUseMeteredNetwork>true</AllowUseMeteredNetwork></DeploymentCreationActionXML>
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Rule XML is: <AutoDeploymentRule xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"><DeploymentName>Test ADR</DeploymentName><DeploymentDescription>Test ADR</DeploymentDescription><LocaleId>1033</LocaleId><UseSameDeployment>false</UseSameDeployment><EnableAfterCreate>true</EnableAfterCreate><NoEULAUpdates>false</NoEULAUpdates><AlignWithSyncSchedule>false</AlignWithSyncSchedule><ScopeIDs><ScopeID>SMS00UNA</ScopeID></ScopeIDs></AutoDeploymentRule>
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Criteria Filter Result XML is: <AutoDeploymentRule xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"><DeploymentName>Test ADR</DeploymentName><DeploymentDescription>Test
ADR</DeploymentDescription><LocaleId>1033</LocaleId><UseSameDeployment>false</UseSameDeployment><EnableAfterCreate>true</EnableAfterCreate><NoEULAUpdates>false</NoEULAUpdates><AlignWithSyncSchedule>false</AlignWithSyncSchedule><ScopeIDs><ScopeID>SMS00UNA</ScopeID></ScopeIDs></AutoDeploymentRule>
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Parsing Deployment Action XML...
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
Parsing Rule XML... SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Could not find element DeploymentId SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Could not find element UpdateGroupId SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Could not find element UpdateGroupName SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
SQL is: select cis.CI_ID from vCI_ConfigurationItems cis join vProvisionedCIs pci on cis.CI_ID = pci.CI_ID where cis.CI_ID in (16793068, 16793070, 16793441, 16793445, 16793531, 16793686, 16793688, 16794597, 16794600, 16794602, 16794604, 16795443,
16795445, 16795709, 16795711, 16796210, 16796222, 16796292, 16796298, 16799495, 16799503, 16799602, 16799700, 16799703, 16799705, 16799712, 16799718, 16800300, 16800302, 16800367, 16800369, 16800371, 16800375, 16801224, 16801227, 16801237, 16801239, 16801287,
16801289, 16801559, 16801566, 16801996, 16802034, 16802839, 16802841, 16803306, 16803310, 16803420, 16803422, 16806477, 16806479, 16809354, 16809360, 16809393, 16809397, 16809774, 16809786, 16809792, 16813338, 16813348, 16813636, 16813638, 16814948, 16814950,
16815151, 16815153, 16817088, 16817102, 16817108, 16817398, 16817400, 16818677, 16818691, 16825397, 16840448, 16840458, 16840460, 16840462, 16840690, 16840700, 16840702, 16840710, 16840824, 16840826, 16842640, 16842641, 16842802, 16842803, 16842841, 16842870,
16842871, 16842896, 16842917, 16843017, 16843042, 16843049, 16843051, 16845981, 16846404, 16846751, 16846757, 16848017, 16848021, 16848664, 16848687, 16849383, 16849385, 16852506, 16852514, 16852516, 16855484, 16857102, 16857151, 16857152, 16857255) order
by cis.CI_ID SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
0 of 115 updates are downloaded and will be added to the Deployment.
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
The rule resulted in no updates being found. Skip deployment creation or update...
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
CRuleHandler: Enforcing Actions for Rule 16777228 failed!
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
CRuleHandler: ResetRulesAndCleanUp() SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Updated Failure Information for Rule: 16777228
SMS_RULE_ENGINE 6/26/2014 9:22:00 AM
5148 (0x141C)
CRuleHandler: Deleting Rule 16777228 SMS_RULE_ENGINE
6/26/2014 9:22:00 AM 5148 (0x141C)
Found notification file C:\Program Files\Microsoft Configuration Manager\inboxes\RuleEngine.box\16777228.RUL
SMS_RULE_ENGINE 6/26/2014 9:22:10 AM
5148 (0x141C)
RuleSchedulerThred: Change in Rules Object Signalled.
SMS_RULE_ENGINE 6/26/2014 9:22:10 AM
5228 (0x146C)
Refreshed ScheduleList instance for Rule (16777228) from schedule string () with next occurence (12/31/1969 7:00:00 PM)
SMS_RULE_ENGINE 6/26/2014 9:22:10 AM
5228 (0x146C)
FindNextEventTime found next event for RuleID 0 as :1/1/2038 12:00:00 AM
SMS_RULE_ENGINE 6/26/2014 9:22:10 AM
5228 (0x146C)
RuleEngine: Got next rule execution time successfully. Next event is in 12369097 minutes
SMS_RULE_ENGINE 6/26/2014 9:22:10 AM
5228 (0x146C)
Sleeping for 15 minutes SMS_RULE_ENGINE
6/26/2014 9:22:10 AM 5228 (0x146C)
Also, I do not have a patchdownloader.log anywhere, Ive checked all aforementioned locations from various sources and it just simply does not exist on my SCCM server. Here is my setup:
Server1: Primary server with all roles installed locally except the site database is on its own server. WSUS is installed locally here and DB is stored here.
Server2: SQL DB for Primary site DB
Server3: Secondary remote site running MP, DP, SUP. DB is SQL Express local.
So the SUP role was installed successfully on both server1 first and server 2 second with the site servers accounts. The SUP Synchronizes successfully and I can see a large list of updates available for use but not downloaded of course. I have set WSUS option
to store updates locally and have plenty of space at the target destination.
So here is my issue, I have been working on this issue for the better part of a week and understand the error code from the ruleengine.log to be a permissions issue. I have also proved this out but creating a test ADR with minimal updates and applied NTFS perms
to the target path for Modify with the everyone group (testing purposes only). The updates downloaded successfully. So this puts me right back to where I was, knowing its a permissions issue but not understanding what permissions are needed. Let me explain
further.
The best way to start is to show what perms I have to the target location for downloads/wsus/sup anything:
Path: \\Server1\UpdatesAndDefinitions (permissions being applied to the UpdatesAndDefinitions root folder)
SCCMAdmin (account used for most SCCM tasks except for NA) / Modify / Share and NTFS
Server1$ (primary site server) / Modify / NTFS
Everyone / read and execute / NTFS and Share
There are other system generated perms but the above three are the important ones. So hence my confusion I know that the SCCMAdmin account or the Server its self has to be accessing the target directory so why is it failing with a permissions issue?
My next step was to enable Auditing on the target path. Doing so revealed just what I thought and through me into further frustration:
A network share object was accessed.
Subject:
Security ID:
SYSTEM
Account Name:
SCCM-MPS$
Account Domain:
DSCI
Logon ID:
0x3e7
Network Information:
Source Address:
fe80::306a:8827:8672:3ba5
Source Port:
50329
Share Name: \\*\UpdatesAndDefinitions
A handle to an object was requested.
Subject:
Security ID:
DSCI\sccmadmin
Account Name:
sccmadmin
Account Domain:
DSCI
Logon ID:
0xad903c
Object:
Object Server:
Security
Object Type:
File
Object Name:
F:\UpdatesAndDefinitions
Handle ID:
0xf5c
Process Information:
Process ID:
0x10cc
Process Name:
C:\Windows\explorer.exe
Access Request Information:
Transaction ID:
{00000000-0000-0000-0000-000000000000}
Accesses:
READ_CONTROL
ReadAttributes
Access Mask:
0x20080
Privileges Used for Access Check:
Restricted SID Count:
0
Now I may not be the best I traversing through the mess of audit entry's and translating them, but from what I can see the two accounts that have the proper share and ntsf perms ive listed above are indeed the ones accessing the target location and the audit
code is success. I filter for failures and found no audits for failures whatsoever yet my downloads still fail religiously, unless of course I open myself up with the everyone group.
So next... I tried adding in the Network Service account with proper permissions, the Local Service Account, my user account, and all no go's.
Next... I remove the SUP roles from SCCM checked the logs for deinstall confirmations, and reinstalled these roles. No Go!
If anyone can assist I would be in your debt and very grateful.
Oh last note, but very important note I'm running SCCM 2012 SP1 CU4
Thanks,
Michael
MichaelSpaulding

I just tested with the everyone group further; I added everyone with modify for ntfs and just read only for share and downloads failed!
I then changed the share perms for everyone to change and the ntfs to read/execute and poof downloads complete! Obviously change share perms for everyone leaves me open which Id like to prevent, so finding what account is being used is crucial.
I have already tried adding all of the SCCM accounts I use and the servers themselves as change perms to share and ntfs and have not had any luck.
MichaelSpaulding

Server 2012 (not R2) RODC fails to install Windows Updates

Good morning all
Since around October, our 80-odd 2012 (non-R2) RODCs have been failing to install windows updates, rolling them back on reboot. Patches that don't require a reboot are fine. The short version is, please log a call with MS and reference this thread, if you're
having this issue as currently they're saying they won't fix this!!
Our product support group opened an official case and reported this with Microsoft and they've found the cause. PLEASE NOTE however, that this relates to RODC and ALL patches failing, not just 3000061 on non-RODC.
There was some chat relevant to this as originally it was thought KB3000061 was to blame, and a few other people had had the same issue there (see links at the bottom). I think however, that this issue now stands alone as any patch we try to install will
fail.
000093 2015-01-23 20:18:30, Info CSI 00000015 Begin executing advanced installer phase 38 (0x00000026) index 4 (sequence 43)
000094 Old component: [ml:350{175},l:348{174}]"Microsoft-Windows-Web-Services-for-Management-Core, Culture=neutral, Version=6.2.9200.16384, PublicKeyToken=31bf3856ad364e35, ProcessorArchitecture=wow64, versionScope=NonSxS"
000095 New component: [ml:350{175},l:348{174}]"Microsoft-Windows-Web-Services-for-Management-Core, Culture=neutral, Version=6.2.9200.17100, PublicKeyToken=31bf3856ad364e35, ProcessorArchitecture=wow64, versionScope=NonSxS"
000096 Install mode: install
000097 Installer ID: {118ca598-79a0-4297-953d-e82183960fd2}
000098 Installer name: [13]"Group Trustee"
000099 2015-01-23 20:18:30, Error CSI 00000001@2015/1/23:20:18:30.673 (F) CMIADAPTER: Inner Error Message from AI HRESULT = HRESULT_FROM_NT(STATUS_NOT_SUPPORTED)
000100 [
000101 (null)
000102 ]
000103 [gle=0x80004005]
000104 2015-01-23 20:18:30, Error CSI 00000002@2015/1/23:20:18:30.673 (F) CMIADAPTER: AI failed. HRESULT = HRESULT_FROM_NT(STATUS_NOT_SUPPORTED)
000105 Element:
000106 [372]"<groupTrustee xmlns="urn:schemas-microsoft-com:asm.v3" name="WinRMRemoteWMIUsers__" description="Members of this group can access WMI resources over management protocols (such as WS-Management via the Windows Remote Management service). This applies only to WMI namespaces that grant access to the user." type="User" enabled="true">
000107
000108 <members></members>
000109
000110 </groupTrustee>"
000111 [gle=0x80004005]
000112 2015-01-23 20:18:30, Error CSI 00000003@2015/1/23:20:18:30.673 (F) CMIADAPTER: Exiting with HRESULT code = HRESULT_FROM_NT(STATUS_NOT_SUPPORTED).
000113 [gle=0x80004005]
Cause:
The installer uses SAM API calls to manage the group. It always connects to the local SAM instance. The component also handles an uninstall task in the same function. On uninstall the group is being deleted.
So the SAM handle is requested with "Create Group" and "Delete" access.
The error happens because a RODC does not allow any changes and thus returns STATUS_NOT_SUPPORTED.
More information about the prevent from accidental deletion feature please refer :
http://technet.microsoft.com/en-us/library/cc773347(v=WS.10).aspx
http://technet.microsoft.com/en-us/library/cc739350(v=WS.10).aspx
Recommendation:
This is a Bug in the RODC running on server 2012, However you may do an in place upgrade to Server 2012 R2 and then proceed with the installation of the patch.
The bad news is this is fixed in 2012 R2 with a hotfix - but it isn't fixed in 2012 and it won't be because.. they've only had one official report logged. And that was by us. So, if you want this fixed, you need to start logging this with MS now.
What I can say just now is that this isn't related to the registry fixes with WinEVT we've all been trying, it's NOT limited to 2008 that has been upgraded in place to 2012 (our product support group replicated it in the lab with a brand new 2012 promoted
to RODC) and it IS only happening with RODC. Possible fix might be to make your RODC RW for a bit and install your patches then.
Background reading:
https://social.technet.microsoft.com/Forums/en-US/f77691d8-a9d0-4714-98ad-71665cfa8965/kb3000061-fails-to-install-on-server-2012?forum=winserver8gen
https://social.technet.microsoft.com/Forums/en-US/70219bcb-36a8-466e-900b-cbf390db38d2/failure-configuring-windows-updates-reverting-changes-postreboot-status-0x800f0922?forum=winserver8gen

The error indicates that IIS is returning a "404 not found" error back to the Windows Update Agent. That might mean that you need to specify the correct port that WSUS is listening on, e.g.:
WSUSServer=http://yourserver:8530
Thanks,
-Michael Niehaus
Senior Product Marketing Manager, Windows Deployment
http://blogs.technet.com/mniehaus
[email protected]

I recently changed my email address and updated my password. However, when I connect my iPhone 4 it defaults to my old email address which is no longer valid. How do I get my phone to recognize my updated email address?

I recently changed my email address and updated my password. However, when I connect my iPhone 4 it defaults to my old email address which is no longer valid. How do I get my phone to recognize my updated email address and how do I now change the iPhone 4 to recognize the new address? I wish to delete all reference to the old address. All help would be appreciated.

Hi.
Here is a procedure that should help.
1. Go to "Settings"
2. Go to "Mail, Contacts, Calendars"
3. Click the account you don't want anymore
4. Go to the bottom and click "Delete Account"
5. Confirm the deletion
6. Go back to "Mail, Contacts, Calendars" (if you're not there already)
7. Add your new account

Mac OS X 10.6.8, receiving error message "Failed to check for updates. The operation couldn't be completed. Operation not permitted." How to fix?

When I try to update my software, I'm receiving the error message "Failed to check for updates. The operation couldn't be completed. Operation not permitted."
I'm using Safari 4.0.3. Yes, I know this is an old version of Safari - I can't update it, or any other software on my MacBook. Should I just wait for the Lion OS, or is there any kind of fix a non-technical Mac user like me can attempt without screwing up her laptop?
I've tried clearing my cache and resetting Safari already - doesn't help. I've also tried to update after disabling my (Norton) antivirus software, thinking that might be interfering. None of these help.
I don't know if it's a related problem, but also I can't download .pdf files from the internet, although I used to be able to.

You should use the NortonAV uninstaller to uninstall it. Disabling the dreadful thing in the past hasn't always been sufficient for it to cease creating system havoc. The Mac NortonAV version has a long and well-earned reputation for doing truly seriously nasty things to OS X. Shame on Comcast for inflicting NortonAV on its Mac customers. It's not a matter of if NortonAV will mess up OS X but when and how badly. I can't help but wondering if some setting in your Norton AV has decided that NortonAV, rather than you, will be making executive decisions about what you are allowed to install on your computer and is keeping that fact a secret.
After you are done uninstalling Norton use the finder to search for any Norton files that the uninstaller might have missed. Add the option to search for invisible files.
After you have removed all the Norton bits and pieces restart in safe mode by holding down the shift key right after the startup chime. Keep holding down the shift key until you see the Apple logo and spinning gear. Safe mode does some maintenance tasks which means a much longer than normal startup time. Use Disk Utility to repair permission
If your Mac works normally in safe mode restart. If things still aren't fixed you might want to give another shot at reinstalling Snow Leopard from the install DVD and applying the Mac OS X 10.6.8 Update Combo before taking your Mac to the Apple Store.
If you feel the need to run AV software on your Mac use ClamXav in manual mode. It's donationware and doesn't seem to cause the litany of weird problems that are associated with other AV software.

I have clicked the Apple Software Update,a window pops up with Failed to check for updates.The operation couldn t be completed. Operation not permitted.This only occurring now did not happen previously.I am using 10.7.4,on a Mbp Pro.

I have clicked the Apple > Software Update,a window pops up with >Failed to check for updates.
The operation could not completed. >Operation not permitted. This is only occuring now.It did not happen
before.The Apple store in Sydney NSW Australia only reinstalled 10.7.4 Lion yesterday.I have downloaded my
Itunes song and reinstalled Intego antivirus.Will somebody please advise me what to do.It is 4:03 PM Saturday
here in Koolewong.
richard.

Uninstall Intego...you don't need it.

Fails to Recognize Symantec Update

Similar Messages

Maybe you are looking for