FCIP Peer in the same VLAN

Hi,
I will have 2 data centre connected with a 1gb possibly 2 x 1gb ethernet link.
There will be some 802.q trunking between location and some traffic will be routed.
I have the option of having my FCIP peer in the same vlan and carried in the trunk. Or have them in different VLAN and routed between location.
Initiallay I though routed would be good because I can use QoS to prioritise FCIP traffice.
But could I still achieve this using single vlan. and is it allowed.
both site are connect using 6509 with sup720s
Thanks
John

Hi John,
For the FCIP link it is just an IP connectivity. So, you can do in both ways as you describe. You can route it or use a vlan. Just make sure that you have no too hign RTT. And also there RTT timout setting on FCIP you can play with that according to your RRT in your network.
Thanks,
Hakan.

Similar Messages

  • ACE30-MOD-k9 in bridge mode. Individual server in the same vlan of Real Servers not reacheable.

    I configured ACE30-MOD-K9 in bridge mode and I configured a server farm with his real servers. The traffic passes and is balanced correctly between all RSERVER. But I can not contact a server that is on the same vlan of the serverpharm but doesn't belong at this serverfarm.
    I Thought that the traffic directed to this "spare" server shouldn't  be balanced but the bridge should permit traffic to pass. (trasperent mode) Is it correct ?
    What does ACE in bridge mode with traffic directed to servers that do not belong to any server farm but are present on the same VLAN (same bridge group)?
    In rispect at the following configuration 10.10.10.168 isn't reacheable
    access-list INBOUND line 8 extended permit ip any any
    access-list INBOUND line 16 extended permit icmp any any
    probe http HTTP_PROBE1
      expect status 200 200
    rserver host RS_WEB1
      ip address 10.10.10.163
      inservice
    rserver host RS_WEB2
      ip address 10.10.10.164
      inservice
    rserver host RS_WEB3
      ip address 10.10.10.165
      inservice
    rserver host RS_WEB4
      ip address 10.10.10.167
      inservice
    serverfarm host SF_FIREGROUP
      rserver RS_WEB1
        inservice
      rserver RS_WEB2
        inservice
      rserver RS_WEB3
        inservice
      rserver RS_WEB4
        inservice
    sticky ip-netmask 255.255.255.255 address source sticky-ip
      replicate sticky
      serverfarm SF_FIREGROUP
    sticky http-cookie myCookie sticky-cookie
      cookie insert browser-expire
      serverfarm SF_FIREGROUP
    class-map match-any VS_FIREGROUP
      2 match virtual-address 10.10.10.169 tcp eq www
      4 match virtual-address 10.10.10.169 tcp eq 8081
      5 match virtual-address 10.10.10.169 tcp eq 8082
      6 match virtual-address 10.10.10.169 tcp eq 8083
      7 match virtual-address 10.10.10.169 tcp eq 8084
      8 match virtual-address 10.10.10.169 tcp eq 8085
      9 match virtual-address 10.10.10.169 tcp eq 8097
    class-map match-any VS_FIREGROUP_HTTPS
      2 match virtual-address 10.10.10.169 tcp eq https
    policy-map type loadbalance first-match HTTP
      class class-default
        sticky-serverfarm sticky-cookie
    policy-map type loadbalance first-match HTTPS
      class class-default
        sticky-serverfarm sticky-ip
    policy-map multi-match HTTP_HTTPS_MULTI_MATCH
      class VS_FIREGROUP
        loadbalance vip inservice
        loadbalance policy HTTP
        loadbalance vip advertise active
      class VS_FIREGROUP_HTTPS
        loadbalance vip inservice
        loadbalance policy HTTPS
        loadbalance vip advertise active
    interface vlan 4
      bridge-group 1
      access-group input INBOUND
      service-policy input HTTP_HTTPS_MULTI_MATCH
      no shutdown
    interface vlan 700
      bridge-group 1
      access-group input INBOUND
      no shutdown
    interface bvi 1
      ip address 10.10.10.150 255.255.255.0
      no shutdown
    ip route 0.0.0.0 0.0.0.0 10.10.10.1
    Thanks a lot
    Francesco

    Hi Francesco,
    Just to add more a bit, A bridge group is very similar to routed mode except ACE cannot NAT pass through traffic, vlan's cannot be shared and couple of other things but client's should be able to access the server as in before.
    But also whether in bridge or routed mode, ACE does create flows and applies other security parameters if configured to the traffic. This is for security. Also, ACE should know the MAC of the device to forward the traffic to. Can you check if ACE has the MAC of the destination? You can also put a route for testing purpose and see if that resolves the issue. That should probably be the quickest way to check if ACE is creating any issue here.
    Regards,
    Kanwal

  • 2 SSIDs on the same Vlan?

    Hi all -
    Newbie question. When I am setting up wireless, will I be able to use 2 different SSIDs on the same vlan?
    Example:
    dot11 ssid Example1
    vlan 2
    authentication open eap eap_methods
    authentication network-eap eap_methods
    dot11 ssid Example2
    vlan 2
    authentication open eap_methods
    authentication network-eap eap_methods

    Hi James,
    Hopefully the attached docs will answer your question:
    Cisco Aironet 1100 Series
    Using VLANs with Cisco Aironet Wireless Equipment
    Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not.
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#
    Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 12.2(15)JA
    Configuring Multiple SSIDs
    vlan vlan-id
    (Optional) Assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. You can assign only one SSID to a VLAN.
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
    Hope this helps!
    Rob
    Please remember to rate helpful posts.......

  • 3750 bandwidth limitation between the same vlan over the trunk

    Hi All,
    I have 2 3750G series switches on the trunk link. some machines are part of vlan1 on the switch 1 and some machines are the part of the same vlan1 on the other switch2. I need to limit the bandwidth between the switches for the vlan1. picture is attached.
    I tried to do through the modulare policy frame work (class-map/service-map and policy-map using the police command) but problems are
    1) 3750 does not support output service policy, so i cannot apply the policy on the output of the trunk link.
    2) I can apply the input policy but it will be only for one machine but not for the others on the same switch. if i apply the policy on per port basis then every port has separate bw limitation. I require to limit the bandwidth on per vlan basis on the trunk port. like vlan 1 takes 10 MB, VLAN2 takes 10 MB on the trunk link when communicating between the same vlans.
    Is there any solution for that scenario? your help in this case will be higly appriciated. As its the layer 2 communication, its hard for me to find the solution. if it was layer 3 then i can do it easily by using the rate-limit commmand on the interface.
    thanks

    On the 4500 series we use vlan-range for this,
    conf t
    qos aggregate-policer 10MB 10 mbps 1250000 byte conform-action transmit exceed-action drop
    policy-map 10MB
    class class-default
    police aggregate 10MB
    interface GigabitEthernet1/1
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,10,12,15
    switchport mode trunk
    switchport nonegotiate
    vlan-range 1
    service-policy input 10MB
    service-policy output 10MB
    end
    dunno if the 3750's have the same options

  • Load balancing within the same ACE across two different contexts residing on the same vlan

    I'm working on a design that requires traffic be sent to a different context in the same ACE. The question I have is can this be done when both reside on the same VLAN. Would the traffic in this case be handled at layer 2 instead of layer 7. Would I have to create a seperate subnet in order to provide loadbalancing?
    |__________________|
    |   | vlan 5         |         |
        |                  |
        |                  |
    Context A        |
                           |
                           |
                        Context B
    Thanks, Jerilyn

    by design, two contexts on the same box in the same vlan can't communicate. You have to use an external L3 device.
    A workaround may be to use two diferent vlans and then bridge between them with a loopback cable.

  • ACE30_MOD-K9 in bridge mode. Individual servers in the same vlan of rserver not reach.

    I configured ACE30-MOD-K9 in bridge mode and I configured a server farm with his real servers. The traffic passes and is balanced correctly between all RSERVER. But I can not contact a server that is on the same vlan of the serverpharm but doesn't belong at this serverfarm.
    I Thought that the traffic directed to this "spare" server shouldn't  be balanced but the bridge should permit traffic to pass. (trasperent mode) Is it correct ?
    What does ACE in bridge mode with traffic directed to servers that do not belong to any server farm but are present on the same VLAN (same bridge group)?
    In rispect at the following configuration 10.10.10.168 isn't reacheable
    access-list INBOUND line 8 extended permit ip any any
    access-list INBOUND line 16 extended permit icmp any any
    probe http HTTP_PROBE1
      expect status 200 200
    rserver host RS_WEB1
      ip address 10.10.10.163
      inservice
    rserver host RS_WEB2
      ip address 10.10.10.164
      inservice
    rserver host RS_WEB3
      ip address 10.10.10.165
      inservice
    rserver host RS_WEB4
      ip address 10.10.10.167
      inservice
    serverfarm host SF_FIREGROUP
      rserver RS_WEB1
        inservice
      rserver RS_WEB2
        inservice
      rserver RS_WEB3
        inservice
      rserver RS_WEB4
        inservice
    sticky ip-netmask 255.255.255.255 address source sticky-ip
      replicate sticky
      serverfarm SF_FIREGROUP
    sticky http-cookie myCookie sticky-cookie
      cookie insert browser-expire
      serverfarm SF_FIREGROUP
    class-map match-any VS_FIREGROUP
      2 match virtual-address 10.10.10.169 tcp eq www
      4 match virtual-address 10.10.10.169 tcp eq 8081
      5 match virtual-address 10.10.10.169 tcp eq 8082
      6 match virtual-address 10.10.10.169 tcp eq 8083
      7 match virtual-address 10.10.10.169 tcp eq 8084
      8 match virtual-address 10.10.10.169 tcp eq 8085
      9 match virtual-address 10.10.10.169 tcp eq 8097
    class-map match-any VS_FIREGROUP_HTTPS
      2 match virtual-address 10.10.10.169 tcp eq https
    policy-map type loadbalance first-match HTTP
      class class-default
        sticky-serverfarm sticky-cookie
    policy-map type loadbalance first-match HTTPS
      class class-default
        sticky-serverfarm sticky-ip
    policy-map multi-match HTTP_HTTPS_MULTI_MATCH
      class VS_FIREGROUP
        loadbalance vip inservice
        loadbalance policy HTTP
        loadbalance vip advertise active
      class VS_FIREGROUP_HTTPS
        loadbalance vip inservice
        loadbalance policy HTTPS
        loadbalance vip advertise active
    interface vlan 4
      bridge-group 1
      access-group input INBOUND
      service-policy input HTTP_HTTPS_MULTI_MATCH
      no shutdown
    interface vlan 700
      bridge-group 1
      access-group input INBOUND
      no shutdown
    interface bvi 1
      ip address 10.10.10.150 255.255.255.0
      no shutdown
    ip route 0.0.0.0 0.0.0.0 10.10.10.1
    Thanks a lot
    Francesco

    Hi Francesco,
    Just to add more a bit, A bridge group is very similar to routed mode except ACE cannot NAT pass through traffic, vlan's cannot be shared and couple of other things but client's should be able to access the server as in before.
    But also whether in bridge or routed mode, ACE does create flows and applies other security parameters if configured to the traffic. This is for security. Also, ACE should know the MAC of the device to forward the traffic to. Can you check if ACE has the MAC of the destination? You can also put a route for testing purpose and see if that resolves the issue. That should probably be the quickest way to check if ACE is creating any issue here.
    Regards,
    Kanwal

  • CSS - src and dst in the same vlan

    Hi guys,
    I need LB something like this in routed mode:
    first data flow:
    [client]->[vip1-c(css)]->[www1/www2]
    and second (backend) flow is:
    [www1/www2]->[vip2-c(css)]->[www3/www4]
    vip1,2-c = VIP address on client side
    www1,2,3,4 = all servers are in the same VLAN
    problematic is second data flow (www1/2 -> vip2 -> www3/4(because www3/4 are in the same VLAN as www1/2).
    I have two solution for this:
    1. migrate www1/2 and www3/4 to the independent VLANs (this can be design problem in existing topology)
    2. communication from www1/2 with destination to www3/4 translate to IP address located on the CSS using group, but I'm not sure if it's possible, or how it's possible to configure on the CSS.
    group gr1
    add service www1
    add service www2
    add destination service www3
    add destination service www4
    vip address ip-from-client-side(for example vip2-c)
    active
    it's possible to use this configuration?
    martin

    The group is a good solution.
    However, the way it was configured is incorrect.
    You either specify the source or destination.
    So, if you want to nat all traffic from www1 and www2 you leave the 'add server www1' commands and remove the 'add destination service www3'.
    Or you can nat all traffic going to www3 and www4. In this case, you remove the 'add service www1' and keep the others.
    Another way of doing this would be to remove all 'add ..' commands and use an acl to specify when to use the group using the option 'sourcegroup gr1' inside the acl.
    Gilles.

  • [ACE] Real servers and VIP in the same VLAN

    Hello.
    I´m facing an issue because the real servers and the VIP address are in the same VLAN, when a request comes from an external client to the VIP (crossing an ASA firewall) , the ACK gets back using the IP of one of the real servers instead of the VIP so this traffic is blocked by our WAN firewall probably due the inspection rules.
    My question is if there is some way make the VIP the address who ACK´s that requests? Creating a new VLAN would be complicated because there are other services already running on those real servers.
    Thanks a lot,
    Miquel

    Hi Miquel,
    Please do source nat on ACE so that return traffic gets sent to ACE and not FW. Pasting an example for you.
         ==========================================================================
         One-Armed Load Balancing with VIP, Servers, & NAT Pool on the Same Subnet
         ==========================================================================
    login timeout 0
    access-list ANYONE line 10 extended permit ip any any
    rserver host SERVER_01
      ip address 192.168.1.11
      inservice
    rserver host SERVER_02
      ip address 192.168.1.12
      inservice
    rserver host SERVER_03
      ip address 192.168.1.13
      inservice
    serverfarm host REAL_SERVERS
      rserver SERVER_01
        inservice
      rserver SERVER_02
        inservice
      rserver SERVER_03
        inservice
    class-map match-all VIP-30
      2 match virtual-address 192.168.1.30 tcp eq www
    class-map type management match-any REMOTE_ACCESS
      description remote-access-traffic-match
      2 match protocol telnet any
      3 match protocol ssh any
      4 match protocol icmp any
    policy-map type management first-match REMOTE_MGT
      class REMOTE_ACCESS
        permit
    policy-map type loadbalance first-match SLB_LOGIC
      class class-default
        serverfarm REAL_SERVERS
    policy-map multi-match CLIENT_VIPS
      class VIP-30
        loadbalance vip inservice
        loadbalance policy SLB_LOGIC
        loadbalance vip icmp-reply active
        nat dynamic 1 vlan 451
    interface vlan 451
      description Servers vlan
      ip address 192.168.1.2 255.255.255.0
      access-group input ANYONE
      service-policy input CLIENT_VIPS
      nat-pool 1 192.168.1.10 192.168.1.10 netmask 255.255.255.0 pat
      no shutdown
    ip route 0.0.0.0 0.0.0.0 192.168.1.1
    Let me know if you have any question.
    Regards,
    Kanwal

  • WCS and WLC, On the same VLAN ?

    Whats best practice ? Is it better to have the WCS on the same vlan as the controller(s)
    Johann Folkestad

    Given the fact that it is snmp traffic, the WCS to WLC snmp read/writes should be confined to a subnet(s) that are secured by ACLs/firewalls/rfc1918 address space, yada yada....
    One way to do it is to place the WCS behind a firewall on the same or reachable subnet as the WLC service or management ports. I prefer using the service port on the WLC for the WCS snmp traffic, this way I can prune that vlan off the switch trunk ports that the WLC connect to as well as put it in a subnet that is away from prying eyes. I have had it working just fine since 3.0.2x all the way up to the latest rev this way.
    the controller will touch an additional vlan for each dynamic interface you create for wlans
    You can also dual home the WCS server, but the default option on WCS install/upgrade is to bind to one interface (it will detect & prompt in regards to multiple interfaces - at least on the Linux version).
    Also don't forget to lock down https access to WCS web frontend as well

  • Hello! I have configured my Wireless network to support bonjour protocol. When I support mDNS in the same Vlan I can see the Apple TV with my iPhone, but I cannot see it with my iPad.

    Hello! I have configured my Wireless network to support bonjour protocol. When I support mDNS in the same Vlan I can see the Apple TV with my iPhone, but I cannot see it with my iPad. Someone know if there is any different in the Bonjour protocol between the iPhone and the iPad???
    It is like if the iPad changes the process at some point...
    Thank you!

    You don't need to configure anything specific for it to work unless you had some special filtering in place already.
    What do you mean specificly by can not "see" it with your iPad?

  • The same SSID used at 3 sites and the same vlan for client IP assignment?

    we are deploying 5508 controller and LW APs for wireless IP phone 7925G
    Controller is installed at site A and there are APs and wireless phones at site B and C as well.
    1. can I use the same SSID for all three sites for wireless phones? or have to use 3 distinct SSIDs?
    2. If I can use the same SSID, can I associate one subnet e.g 10.10.131.0/24 for wireless IP phones at 3 sites? (our Cisco UCM is fine with this)
    3. if I have use 3 distinct SSIDs, do I have to assign three subnets for IP phones at three sites?
    thanks for the help!
    Eric

    yes.. this is done by HREAP mode.. the below link will help you out!!
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml
    That is, by default the WLAN will get pushed to all APs.. so if you have a single wlan then this will broadcast the SSID and the remotre site clients will connect to it..
    Lemme know if this answered your question!!
    Regards
    Surendra

  • Cant communicate between nodes on the same vlan but on different switches (cat/nexus)

    Very odd situation that I cant quite figure out.
    I have two nexus switches connecte together with PO5
    Each Nexus has PO6 which connects to a Cat3750
    The nodes are all on vlan 46.
    Nodes that are connected to the nexus switches can ping each other but cant ping other nodes on the cat. switch.
    Here is an oddity. Nodes on the CAT switch CAN ping nodes on the nexus switches.
    It would appear that the nodes on the nexus (or the switches themselves) do not get the arp requests.
    Oddity 2. When I do show vpc I see on one of the nexus vlan 46 is active
    id     Port        Status Consistency Reason                     Active vlans
    6      Po6         up     success     success                    1,31,34,46,200,600-605
    When I look at the other switch I dont see vlan 46.
    id     Port        Status Consistency Reason                     Active vlans
    6      Po6         up     success     success                    1,31,34,200,600-605
    Comparing the configs I dont see a difference between the two (eyeballing sho run)
    Here are the running configs for PO6 on both switches (identical)
    MTL-N3548COLO-1# sho run int po6
    interface port-channel6
      switchport mode trunk
      spanning-tree port type normal
      speed 1000
      vpc 6
    Not sure what I am missing. Any help is appreciated.
    Thanks
    Drew

    Your setup with vMotion on a separate subnet is absolutely correct. For the vMotion issues I'd suggest you google for vMotion 14% which will list a couple of KB articles with possible issues and resolutions/workarounds.
    André

  • WLC 7.4.110.0 where native vlan and SSID vlan is the same vlan

    Hi
    We have app. 1500 accespoints in app. 500 locations. WLCs are WiSM2s running 7.4.110.0. The AP are 1131LAPs.In a FlexConnect configuration we use vlan 410 as native vlan and the ssid (LAN) also in vlan 410. This works fine, never had any problems with this.
    Now we have started use 1602 APs and the client connection on ssid LAN becomes unstable.
    If we configure an different ssid, using vlan 420 and native vlan as 410, everything works fine.
    I can't find any recommandations regarding the use of native vlan/ssid vlan
    Is there anyone experiencing similar problems? Is this a problem with my configuration or is it a bug wittin 1602 accespoints?
    Regards,
    Lars Christian

    It is the recomended design to put FlexConnect AP mgt into native vlan & user traffic to a tagged vlan.
    From the QoS perspective if you want to enforce WLC QoS profile values, you have to tag SSID traffic to a vlan (other than native vlan) & trust CoS on the switch port connected to FlexConnect AP (usually configured as trunk port)
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .

    HI All,
    I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
    Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
    The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
    here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
    show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"   , DESCR: "Cisco 5500 Series Wireless LAN Controller"
    PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... WLAN Controller 5508
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 10.125.18.15
    Last Reset....................................... Software reset
    System Up Time................................... 41 days 5 hrs 14 mins 42 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... US - United States
    --More or (q)uit current module or <ctrl-z> to abort
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 10
    Number of Active Clients......................... 61
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    AP Bundle Information
    Primary AP Image  Size
    ap3g1             5804
    ap801             5192
    ap802             5232
    c1100             3096
    c1130             4972
    c1140             4992
    c1200             3364
    c1240             4812
    c1250             5512
    c1310             3136
    c1520             6412
    c3201             4324
    c602i             3716
    Secondary AP Image      Size
    ap801             4964
    c1100             3036
    --More or (q)uit current module or <ctrl-z> to abort
    c1130             4884
    c1140             4492
    c1200             3316
    c1240             4712
    c1250             5064
    c1310             3084
    c1520             5244
    c3201             4264
    Press Enter to continue or <ctrl-z> to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
           case-check ...........Enabled
           consecutive-check ....Enabled
           default-check .......Enabled
           username-check ......Enabled
    Press Enter to continue or <ctrl-z> to abort
    Network Information
    RF-Network Name............................. OGR
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or <ctrl-z> to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect ................... Disable
    Fast SSID Change ........................... Enabled
    AP Discovery - NAT IP Only ................. Enabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or <ctrl-z> to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr Type   Stat   Mode     Mode     Status   Status Trap    POE   SFPType  
    1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
    2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    Press Enter to continue or <ctrl-z> to abort
    AP Summary
    Number of APs.................................... 8
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1       US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1       US       1
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1       US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1       US       1
    Anham_AP03           2     AIR-LAP1142N-A-K9     70:81:05:88:15:b5 default location 1       US       1
    ANHAM_AP01          2     AIR-LAP1142N-A-K9     70:81:05:b0:e4:62 Small Conference 1       US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1       US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9     70:81:05:96:7a:49         Copy Room 1       US       1
    AP Tcp-Mss-Adjust Info
    AP Name             TCP State MSS Size
    KNOWLOGY_DC01       disabled   -
    KNOWLOGY_DC02       disabled   -
    --More or (q)uit current module or <ctrl-z> to abort
    KN1252_AP01         disabled   -
    KN1252_AP02         disabled   -
    Anham_AP03           disabled   -
    ANHAM_AP01           disabled   -
    ANHAM_AP04           disabled   -
    ANHAM_AP02           disabled   -
    Press Enter to continue or <ctrl-z> to abort
    AP Location
    Total Number of AP Groups........................ 3  
    Site Name........................................ ANHAM8075
    Site Description................................. ANHAM 8075 Location
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Anham_AP03           2     AIR-LAP1142N-A-K9   70:81:05:88:15:b5 default location 1     US       1
    ANHAM_AP01           2     AIR-LAP1142N-A-K9   70:81:05:b0:e4:62 Small Conference 1     US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1     US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9   70:81:05:96:7a:49         Copy Room 1     US       1
    Site Name........................................ Knowlogy_DC
    --More or (q)uit current module or <ctrl-z> to abort
    Site Description................................. DC Center Access points
    WLAN ID         Interface         Network Admission Control         Radio Policy
    2               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1     US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1     US       1
    Site Name........................................ OGR
    Site Description................................. 1934 OGR Office
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                        None
    4               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    --More or (q)uit current module or <ctrl-z> to abort
    7               knowlogy_ogr        Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1    US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1     US       1
    Site Name........................................ default-group
    Site Description................................. <none>
    WLAN ID        Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    5               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                          None
    --More or (q)uit current module or <ctrl-z> to abort
    9               knowlogy_ogr         Disabled                         None
    10             management           Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Press Enter to continue or <ctrl-z> to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch IP Address.................. 10.125.18.15
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
        Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
        Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
    --More or (q)uit current module or <ctrl-z> to abort
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 11
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
    --More or (q)uit current module or <ctrl-z> to abort
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
          CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
          36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
         Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 44
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    --More or (q)uit current module or <ctrl-z> to abort
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
        Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or <ctrl-z> to abort
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 1
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
         Coverage exception level................... 25 %
    --More or (q)uit current module or <ctrl-z> to abort
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
           36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
        Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 36
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
          Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 5
    Cisco AP Name.................................... KN1252_AP01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:ef:06:50
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.125.18.101
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.125.18.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ Knowlogy Conference Rooms Side
    Cisco AP Group Name.............................. OGR
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.4.10.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. PoE/Medium Power (15.4 W)
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1252AG-A-K9
    AP Image......................................... C1250-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX122990L5
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 118
          WLAN 1 :........................................ 111
          WLAN 2 :........................................ 111
          WLAN 4 :........................................ 112
          WLAN 6 :........................................ 112
          WLAN 7 :........................................ 111
          WLAN 9 :........................................ 112
          WLAN 8 :........................................ 112
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 26 days, 00 h 24 m 39 s
    --More or (q)uit current module or <ctrl-z> to abort
    AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
    Join Date and Time............................... Wed Oct 9 10:59:07 2013
    Join Taken Time.................................. 0 days, 00 h 00 m 50 s
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211n-2.4
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 7
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:df:a5:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           11000 Kilo Bits.......................... MANDATORY
         MCS Set
           MCS 0.................................... SUPPORTED
           MCS 1.................................... SUPPORTED
           MCS 2.................................... SUPPORTED
           MCS 3.................................... SUPPORTED
           MCS 4.................................... SUPPORTED
           MCS 5.................................... SUPPORTED
           MCS 6.................................... SUPPORTED
           MCS 7.................................... SUPPORTED
           MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
           MCS 10................................... SUPPORTED
           MCS 11................................... SUPPORTED
           MCS 12................................... SUPPORTED
           MCS 13................................... SUPPORTED
           MCS 14................................... SUPPORTED
           MCS 15................................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
    --More or (q)uit current module or <ctrl-z> to abort
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 ..........

    Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
    Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
    There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
    Sent from Cisco Technical Support iPhone App

  • Need to configure different SSIDs on same VLAN on 1142

    We're having a problem with interference in the B/G range due to the large number of access points owned by other companies in a fairly small area. The various laptops keep deauthenticating, which is causing problems with applications. I'd like to configure two SSIDs on the same VLAN but have them broadcasted on different frequencies. The AP complained about the configuration when I added the Company5.8 SSID below stating another SSID can't be added to a VLAN, but it shows in the configuration. Does any one have a suggestion as to what I can try? Thanks
    interface Dot11Radio0
     no ip address
     no ip route-cache
     encryption vlan 1 mode ciphers aes-ccm
     encryption vlan 3 mode ciphers aes-ccm
     ssid Moleculera Labs
     ssid Moleculera Labs-guest
     antenna gain 0
     mbssid
     channel least-congested 2412 2437 2462
     station-role root
    interface Dot11Radio0.1
     encapsulation dot1Q 1 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
     bridge-group 1 spanning-disabled
    interface Dot11Radio0.3
     encapsulation dot1Q 3
     no ip route-cache
     bridge-group 3
     bridge-group 3 subscriber-loop-control
     bridge-group 3 block-unknown-source
     no bridge-group 3 source-learning
     no bridge-group 3 unicast-flooding
     bridge-group 3 spanning-disabled
    interface Dot11Radio1
     no ip address
     no ip route-cache
     encryption mode ciphers aes-ccm
     encryption vlan 1 mode ciphers aes-ccm
     encryption vlan 3 mode ciphers aes-ccm
     ssid Moleculera Labs
     ssid Moleculera Labs-guest
     antenna gain 0
     dfs band 3 block
     mbssid
     channel dfs
     station-role root
    interface Dot11Radio1.1
     encapsulation dot1Q 1 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
     bridge-group 1 spanning-disabled
    interface Dot11Radio1.3
     encapsulation dot1Q 3
     no ip route-cache
     bridge-group 3
     bridge-group 3 subscriber-loop-control
     bridge-group 3 block-unknown-source
     no bridge-group 3 source-learning
     no bridge-group 3 unicast-flooding
     bridge-group 3 spanning-disabled

    Amjad, if I delete "encryption mode ciphers aes-ccm" what kind of encryption will the AP use?
    Mohanak, I'm using the same encryption settings with VLANs
    Here is the more complete configuration:
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname COMPANY-AP
    no logging console
    enable secret 5 *
    no aaa new-model
    no ip domain lookup
    ip domain name COMPANY.local
    dot11 syslog
    dot11 ssid COMPANY-2.4
       vlan 1
       authentication open
       authentication key-management wpa
       mbssid guest-mode
       wpa-psk ascii 7 *
    dot11 ssid COMPANY-5.8
       vlan 1
       authentication open
       authentication key-management wpa
       mbssid guest-mode
       wpa-psk ascii 7 *
    dot11 ssid COMPANY-guest
       vlan 3
       authentication open
       authentication key-management wpa
       guest-mode
       mbssid guest-mode
       wpa-psk ascii 7 *
    bridge irb
    interface Dot11Radio0
     no ip address
     no ip route-cache
     encryption vlan 1 mode ciphers aes-ccm
     encryption vlan 3 mode ciphers aes-ccm
     ssid COMPANY-2.4
     ssid COMPANY-guest
     antenna gain 0
     mbssid
     station-role root
    interface Dot11Radio0.1
     encapsulation dot1Q 1 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
     bridge-group 1 spanning-disabled
    interface Dot11Radio0.3
     encapsulation dot1Q 3
     no ip route-cache
     bridge-group 3
     bridge-group 3 subscriber-loop-control
     bridge-group 3 block-unknown-source
     no bridge-group 3 source-learning
     no bridge-group 3 unicast-flooding
     bridge-group 3 spanning-disabled
    interface Dot11Radio1
     no ip address
     no ip route-cache
     encryption mode ciphers aes-ccm
     encryption vlan 1 mode ciphers aes-ccm
     encryption vlan 3 mode ciphers aes-ccm
     ssid COMPANY-2.4  (Want this to be COMPANY-5.8)
     ssid COMPANY-guest
     antenna gain 0
     dfs band 3 block
     mbssid
     channel dfs
     station-role root
    interface Dot11Radio1.1
     encapsulation dot1Q 1 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
     bridge-group 1 spanning-disabled
    interface Dot11Radio1.3
     encapsulation dot1Q 3
     no ip route-cache
     bridge-group 3
     bridge-group 3 subscriber-loop-control
     bridge-group 3 block-unknown-source
     no bridge-group 3 source-learning
     no bridge-group 3 unicast-flooding
     bridge-group 3 spanning-disabled
    interface GigabitEthernet0
     no ip address
     no ip route-cache
     duplex auto
     speed auto
     no keepalive
    interface GigabitEthernet0.1
     encapsulation dot1Q 1 native
     no ip route-cache
     bridge-group 1
     no bridge-group 1 source-learning
     bridge-group 1 spanning-disabled
    interface GigabitEthernet0.3
     encapsulation dot1Q 3
     no ip route-cache
     bridge-group 3
     no bridge-group 3 source-learning
     bridge-group 3 spanning-disabled
    interface BVI1
     ip address 192.168.67.3 255.255.255.0
     no ip route-cache
    ip default-gateway 192.168.67.1
    ip http server
    ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    line vty 0 4
     exec-timeout 30 0
     password 7 *
     login local
    end
    COMPANY-AP#

Maybe you are looking for