Germany: Hansenet (Alice) Router 1121 (TV/WLAN)

(auf deutsch unter http://blogtimes.info/alice-dsl-und-mac-os-x-10-6/)
Hansenet (Alice) is a german internet provider. They supply a branded Siemens-Router with their product. This Router has a severe bug in its firmware, making DNS unresponsive when using DHCP. The bug only occurs in conjuction with Mac OS X 10.6 (Snow Leopard). The symptom is that you are properly connected to the internet but cannot load any webpage. Pinging IP-adresses works, but resolving names does not.
I do know three solutions to overcome this problem:
1. Turn off DHCP on the router and assign individual IP-adresses manually, e.g. 192.168.1.1 for the router, 192.168.1.10 for your computer. On your mac set the netmask to 255.255.255.0, default gateway and dns-server to 192.168.1.1 (the router's IP). Change the '10' in the ip-address for each additional computer to any value between 11 and 254. Do not use the same value on different computers.
2. Keep DHCP turned on, but assign on any connected computer the DNS-server manually to an ip-address out of this list:
ns1.hansenet.de Hamburg 213.191.73.65
ns2.hansenet.de Hamburg 213.191.74.20
ns3.hansenet.de Hamburg 62.109.123.198
name1.hansenet.de Hamburg 213.191.74.18
name2.hansenet.de Hamburg 213.191.92.87
name3.hansenet.de Hamburg 213.191.74.19
name4.hansenet.de Hamburg 213.191.92.86
name5.hansenet.de Hamburg 62.109.123.196
name6.hansenet.de Hamburg 62.109.123.6
name7.hansenet.de Hamburg 62.109.123.196
name8.hansenet.de Hamburg 62.109.123.6
name9.hansenet.de Hamburg 62.109.123.197
name10.hansenet.de Hamburg 62.109.123.7
3. Use the 1121 router as a dumb modem and attach it to an airport extreme.
Reset the router by pushing the reset-button in the bottom. Do not enter any data, just connet it between the DSL-splitter and the wan-port of your airport.
Enter provider data (account/password) in the WAN-section of your airport.

never mind
edited by the Jolly Green Giant (where Green stands for environmentally friendly)

Similar Messages

Router WRVS4400N-EU - WLAN Probleme

Hallo,
mit einem Router WRVS4400N-EU sind einige Probleme aufgetreten.
1. Verbindung mit dem iPhone 4
Die WLAN Verbindung ist eingerichtet und funktioniert. Jedoch nach längerem standby wird das WLAN weiterhin als verbunden angezeigt, der netzwerkzugriff besteht jedoch nicht mehr. Erst ein deaktivieren und aktivieren des WLANs ermöglicht wieder die Nutzung des WLANs.
Ich habe versucht dieses Problem zu umgehen indem ich einen statische IP vergebe. Es bringt jedoch keine Besserung.
Die Verschlüsselung ist auf wpa2 personal gestellt.
2. Verbindung anderer Geräte per WLAN
Der Internetzugriff funktioniert.
Aber der Server beziehungsweise seine Freigaben werden nur bei einer Verbindung per LAN angezeigt, nicht im WLAN.
Eine Verbindung auf den Server per IP ist jedoch möglich.
Getestet: OS X Schneeleopard, Windows 7
Gruß Cornelius Wasmund
P.s.
Siehe auch: https://supportforums.cisco.com/thread/2107089

Leider nicht.
Unser Kunde hat die HW gegen ein anderes Model ausgetauscht!
Hilfe von Cisco war sehr bescheiden !

AirPort Extreme and Arcor/ Vodafone EasyBox A300 WLAN

To whom it may concern:
Had issues during the last days getting an AirPort Extreme (802.11n & 7.4.2) to work with Arcor/ Vodafone as DSL provider in Germany (historic EasyBox A300, but newer WLAN modems/ routers should be comparable).
- Simply connecting the AirPort to the Arcor StarterBox does not work as neither the StarterBox nor the AirPort serve as routers.
- Serially connecting the EasyBox and the AirPort leads to conflicting DHCP/ NAT/ whatever responsibilities giving me connectivity on some ports (Skype) - no connectivity on others (HTTP, SMTP).
- My first guess - following various threads - was to configure the A300 as a bridge and let the AirPort handle my LAN. No success.
- The solution: Turn off WLAN on the EasyBox (to avoid the slower/ old WLAN). Let the EasyBox handle DHCP and NAT on a manually fixed IP x.y.z.1. Configure the AirPort as a bridge only (connect via Ethernet, not PPPoE). Fix it's IP as x.y.z.2. Set the DHCP range on the EasyBox from x.y.z.3 to whatever you need.
- In case you want to share a printer or disk on the Extreme with a Windows machine connected to the AirPort, make sure to install Bonjour for Windows there!
Hope this helps. Any other experiences?

Unfortunately the Vodafone is not sold here in the US so all I can tell you is to disable all of the router features of the vodaphone. try configuring it as if were only connected to a single computer and then replace the Airport Extreme for that computer.

Wlan big isseus

hi everbody,
i have a big problem with my imac 24" middle-2007 model.
when i activate the wlan / aiport, he can´t found my wlan from my or neightbours router. maybe 2 wlan.
- channel change
- passphare type change
- reinstall of macosx
- macosx change (mavericks, mountain lion, lion, ...)
or anything not working , ....
but when i install windows over bootcamp. the wlan works fine on windows bootcamp.
- hardware isseus ruled out!
and now when i start / boot macosx again, the wlan works perfect.
why? mac os bug? kext / driver bug?
sorry for my bad english.

There are 1729 reasons for a "No Gateway" reply. Setting up such complicated VPN connections is not for amateurs (no offence). The best thing you can do is to contact the IT department of your Uni.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Frequent WLan disconnections on Equium M40X-230

My laptop suffers frequent disconnections from the internet and it is getting very annoying. Situation is the laptop connects wirelessly to the net via a Belkin router. The router is working ok, and I use Aol for ISP.
Our second laptop, also a Toshiba but a Sattelite A30-203 does not suffer the problems despite using the same router.
Both laptops have service pack 2 on and the M40 is mobile centrino whilst the Sattelite has a wireless adaptor card installed (also Belkin).
If I watch the connection speed it varies between 54mbps and 1mbps and still says that the signal strength is excellent no matter what the speed is.Does this mean the problem lies with the laptop or its settings, or does it need chipset drivers to be upgraded?
Any help would be appreciated as the slow performance especially when loading pages on the net is driving me daft.

Hi
You should know that there are different WLan standards which supports different properties.
The standards are 802.11 A, B or G. At this time the wireless 802.11 G standard supports the fastest connection.
The best combination is the using of the router and Wlan card which supports the same standard.
You have suggested that the Satellite A30 uses the Belkin WLan adapter. I assume there is the best compatibility between Belkin router and Belkin WLan card. Therefore you will get the best performance.
However, on your Equium you should check the WLan card properties. There you should find some options which could increases the card and connectivity performance.
Important: The power saving option should be disabled in the card properties. Try also to set the WLan range to the highest level.
Additionally its advisable checking the WLan card driver updates. If you use a Intel WLan card check the Intel page for updates.

Route Optimization in CRM Mobile

Hello,
Is anybody familiar with the route optimization in CRM Mobile? According to the documentation a PTV eServers have to be installed. What is a PTV eServer? How do you install it, and what does it cost?
In activity management there is a button called Corridor Search. When I click on it I get an error stating that an u2018Error during corridor searchu2019 Context: ACTOPTIMIZE.
I assume that this button is somehow related to the route optimization. Does anybody know more precisely what it covers, and how to activate this functionality?
Thank you in advance.
Best Regards
Andy Cooper

Hi Andy
Once upon a long time ago I had to deal a bit with PTV: They are located in Germany, and provide route optimization SW: www.ptv.de. The best would be to access their website and ask the information there, they are usually pretty friendly.
Regards, Kai

E1700 Advanced Routing - help needed

I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils

I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils

BEFW11S4 WLan light is off

My laptop can no longer connect to my BEFW11S4 v2 router. The "WLAN Link" light is off. I have the latest firmware, 1.45.10, reflashed it twice and tried an older version of firmware from the Linksys ftp site without success, then reloaded 1.45.10. The router has wireless "enabled" and SSID broadcast "enabled". I also did a "one minute reset" on the back of the router but had no success in getting WLAN to light up.
My "wired" ports on the router are having no problems connecting to the Internet. All other lights are functioning normally. The "wireless" had been working for about two years.
Any suggestions on what else I can try...?

Ok. so the laptop and your PSP cannot detect the router? it seems that your are familiar going to the setup page of the router. so access the setup page again, then go to the wireless tab. make sure that "wireless ssid broadcast" is set to "enabled", and you may also want to try changing channels on the router. after changing channels, powercycle the router (turning it ON and OFF), if same problem, reply to this message.

Router Cisco 891-w SSID BroadCast

i have successfully been able to configure my 891w router with a wireless network, but even when i allow the SSID to broadcast (Using the GUI option Enable Broadcast), as soon as i save the settings with the SSID broadcast enabled. it goes back to SSID broadcast not enabled.
Thanks

Hi,
This command should be entered inside the radio module..
Issue the command on the router
service module wlan-ap 0 session
U will go into the AP module..
here, configure the guest-mode
en
conf t
dot11 ssid
guest-mode
end
lemme know if this helps..
Regards
Surendra

Can not connect to WLAN on every place where the WLAN is available

Sometimes my computer will connect and detect wireless networks, airports hotels etc but will not work at home and in some ofices.
I run WXP updated with SP2 have an Artheros5005gs adapter. Any ideas?

Hi
This is a question of compatibility between the WLan router and the WLan card.
If the WLan card does not support the same Wlan standards then you will be not able to establish the wlan connection.
Mostly the Hot spots (Wlan on airports, city, etc) are not secured and therefore the notebook connects automatically to such Wlans.
The Wlan at home or in the office is mostly secured and you need an right encryption key to connect to such Wlans.
So I think you should check you WLan router configuration settings and use the right encryption key, SSID, etc

N82 wlan won't stay disconnected

Hi
In my block of flats there is a public wifi server that you can connect to the internet through. i was told it was free, but when i connected on my n82 i found that you had to pay, so i gave up.
Now, whenever i'm at home my n82 (black) connects to this router even when wlan scanning is off! drains my battery really quick! i've tried disconnecting but after a few seconds it connects again automatically!
How do i stop this from happening? It's so annoying as drains my battery really fast.
Any help would be much appreciated
James
Solved!
Go to Solution.

problem resolved - ish - go out of range of router. go to tools > settings > connection > access points and the delete the offending access point. have to go out of range in order to break the connection

Equium A60 - No Wlan card but I want to use WLan connection

Hi there,
I just bought a A60 Equium laptop without the Atheros AR5001 wireless adaptor card installed.
Do i need to buy this type of adaptor card to run wireless or is there any other models of Atheros cards i can use or would it be better to buy a usb wireless adaptor.
Many thanks juan

Hi
You can buy an USB WLan stick.
Such sticks are not expensive and easy in use!
If you Wlan router would support WLan 802.11 B/G or N then I recommend buying an USB WLan stick which would support both Wlan standards G and N
802.11 N standard is the newest one and you would get the fastest connection using 802.11 N.
But as I said; this depends on your WLan router

DNS Registration for clients with WLAN and LAN adapters

I have read a number of articles and it seems that there are a number of people who have problems with DNS and workstations with both WLAN and LAN adapters. I haven't however found workable solutions.
Workstation Connection Objective:
To enable DNS discovery and Ip connection to client workstations regardless of whether the client is using the WLAN or LAN. Enabling users to use either Wireless or LAN adapter adhoc. ie they dock their laptops at their desks, and undock to take their laptops
to meetings or consulations with peers. I need to be able to discover and connect to the workstations irrespective of the adapter being used at any time.
Most people seem to try to control which interface is used on the workstations, ie disable WLAN and only use LAN etc. Trying to disable interfaces isn't going to be feasible and its very inflexible.
I believe I can ensure that the workstations use the NICs in our preferred order:
1. LAN
2. WLAN - Our wireless network isn't as fast as the LAN.
By setting specific DHCP metric for the WLAN Router to be higher(ie 2) than the LAN(1). When the LAN isn't connected traffic will route via the WLAN adapter and when the LAN adapter is connected, its router metric will be lower and it will be the preferred
gateway/route.
But how do I solve the DNS resolution for connection to that asset?
If I disable DHCP Server updates into DNS and allow secure updates from the client. It would be really good if DNS client behaved in the following manner
1. The LAN adapter(referred to as primary ie LAN) with the lowest metric(ie 1) registers/auto updates DNS with the ip(both A and PTR). Any other Adapters don't register. - ie the WLAN
2. The Laptop is undocked and the LAN adapter goes offline, the DNS Client then triggers a registration/auto updates its existing DNS entry with the ip from the next adapter(WLAN) with the next lowest gateway metric(2)...hence replacing the first ip registered.
3. The laptop is docked again, and DNS Client triggers a registration/auto updates its existing DNS entry with the IP from the primary adapter(LAN), replacing the WLAN ip.
So there is only ever 1 ipaddress registered for a workstation and it will always be a valid address. Then I don't need to be concerned about whether the user has the wireless turned on and docked.
Being able to discover and communicate with all our workstations in our sites is crucial requirement....
This microsoft article says, http://technet.microsoft.com/en-gb/library/cc771255.aspx
Dynamic updates can be sent for any of the following reasons or events:
    * An IP address is added, removed, or modified in the TCP/IP properties configuration for any one of the installed network connections.
    * An IP address lease changes or renews with the DHCP server any one of the installed network connections. For example, when the computer is started or if the ipconfig /renew command is used.
    * The ipconfig /registerdns command is used to manually force a refresh of the client name registration in DNS.
    * At startup time, when the computer is turned on.
    * A member server is promoted to a domain controller.
However from what I am reading, both adapters(LAN,WLAN), if configured to update DNS, will register their Ip addresses. Which leads to an invalid DNS entry if the laptop is undocked, as the IP for LAN adapter isn't removed.
Has anyone solved this problem for their organizations without
1. Controlling which adapter is used - large management overhead
2. Only allowing one adapter to register with DNS
   - If using LAN adapter for DNS, then anytime the user is using WLAN, their workstation doesn't have a valid DNS entry. Which also impacts Kerberos.
   - If using the WLAN, then we would have to invest a large amount of money into Wireless to provide the necessary bandwidth
3. Setting GPO's to configure dns updates every 30mins on clients
   - Inconsistent results...which I think is sometimes a worse problem
4. Defining separate DNS suffixes for their WLAN networks (I read some people did this)
   - This doesn't remove an invalid DNS entry ie the ip(LAN adapter) DNS entry if the laptop is undocked
   - It also creates problems with kerberos, if the host is registered under a separate DNS suffix from the Active Directory domain name

Hi,
From my point of view, DNS can't be so smart.
As a workaround, please try the steps below,
Disable the DNS register of wireless adapter
Put "ipconfig /regiserdns" in a bat file
Everytime when the wired network is undocked, run the bat file.
If the wired network is docked, wired adapter will register the DNS record.
When the wired network is undocked, run the bat file, then the wireless adapter will register the DNS record.
If the wired network is docked again, wired adapter will register the DNS record automatically.
Best Regards.
Steven Lee
TechNet Community Support

Hallo, wer weis wie ich meine neuer Fernseher von Samsung Typ 40 d7090? mit meinen ipad2 mit der Remote apps verbinden kann, bekomme das nicht hin, weder über WLAN noch über Bluetooth?

Hallo, wer weis wie ich mein iPad2 mit meinem TÜV Samsung Typ 40d7097 verbinden kann, das iPad findet auch das Netzwerk vom Tv, fragt auch nach dem Passwort aber es funktioniert nicht!!! Mein fernseher ist auch mit meinem Router verbunden über WLAN, habe auch nur ein Passwort dafür, kommt immer die fehlerMeldung sec-Linkshare mit einer Nummer ?
Bitte um Hilfe?
Gruß saxo22

Habe leider die gleichen leidvollen Erfahrungen gemacht, allerdings auf einem komplett neuen Rechner mit Aususboard. Dualcore CPU und alles was neu ist und Geld kostet.
Ich findes es sehr bedauerlich, dass Matrox so viele Leute werkeln lässt nur um festzustellen, dass es nicht geht. Soviel Negativmarketing sollte man sich als renomierter Hersteller nicht leisten.
Ein laufendes System kann nicht durch ein noch so tolles (auf dem Papier) neues nicht funktionierendes System ersetzt werden. Leider falle ich immer wieder darauf rein, andere wohl auch.
In der Summe der verbrauchten Zeit ist das laufende System sicher besser.
Wir Anwender sind da viel zu nachsichtig mit den Herstellern.
Schade ist auch, dass Matrox keine Informationen gibt, wann denn 6153 durch ein wirklich funtionierendes Build ersetzt wird.
Gruß
Ulrich Muzyk

LTE in Germany using Telekom/Vodafone LAN-to-LAN tunnel

Hello !
We habe some locations with very slow DSL connetion (< 200 kbit). Some services need direct vpn-connection to the datacenter and some RDP access etc. - the networks are connceted with LAN-to-LAN ipsec tunnel. Work's fine with slow speed.
Now we like to set up one side with LTE. Did someone set up ipsec with one side via LTE via Telekom or Vodafone in Germany ?

PIN:
router#cellular 0/2/0 gsm sim unlock 6543
Create the profile:
router#cellular 0/2/0 gsm profile create 1 apnname.net
AT command is
ATD*gprs_sc*CID#
or
ATDT*gprs_sc*CID#
where gprs_sc (GPRS service code) is 99, but 98 can also work. T-Mobile says 99, Cisco docs contain 98.
                  Some modem manual says:
                 99 (GPRS Service Code) a digit string (value 99) that identifies a
                   request to use the Packet Domain service.
                  98 (GPRS Service Code) a digit string (value 98) that identifies a
                   request to use the IP service
CID (PDP Context Identifier) is the connection profile number (see show cellular 0/2/0 profile ), number between 1..16 This profile contains the APN name.
Typical AT command is: ATD*99*1#*
(Or simply *99# , default CID is obviously 1 )
I don't think you need a chat-script:
interface Cellular0/1/0
no ip address
encapsulation ppp
load-interval 30
dialer in-band
dialer pool-member 1
dialer-group 1
async mode interactive
interface Dialer0
ip address negotiated,
no ip redirects
no ip proxy-arp
encapsulation ppp
load-interval 30
dialer pool 1
dialer idle-timeout 0
dialer string "*99*1#"
dialer persistent
dialer-group 1
no cdp enable
ppp pfc local forbid
ppp pfc remote reject
ppp acfc local forbid
ppp acfc remote reject
ppp eap refuse
ppp eap local
ppp chap refuse
ppp ms-chap refuse
ppp ms-chap-v2 refuse
ppp pap refuse
ppp ipcp address accept
dialer-list 1 protocol ip permit
Troubleshooting:
sh int cell0/0/0
sh cell 0/0/0 all
(config)#service internal
(config)#exit
#test cellular 0/0/0 modem-power-cycle

Germany: Hansenet (Alice) Router 1121 (TV/WLAN)

Similar Messages

Maybe you are looking for