GigE port stuck in init state on SSN-16

I have a Cisco MDS 9222i running NX-OS 6.2(3) with a SSN-16 module in slot 2.  One of the GigE ports with an active connection to a FEX remains in the "init" state.  Shutting and no shutting the port doesn't change the state.  When I move the SFP and cable from the problematic port to another port it comes up immediately.  Has anybody heard of this problem?

Hi,
Are you seeing hellos across the link (debug ip ospf hello)? If so, please check the MTU settings on both interfaces and set the OSPF link type (point-to-point).
If there are no OSPF hellos received you have to ask your provider to troubleshoot the problem with you. In principle it should work.
Hope this helps!
Regards, Martin

Similar Messages

  • Mgt interface stuck in init state

    I can not connect to my mgt minterface on my mds 9509.
    The only thing that looks odd is the mgt interface status. Is this normal?
    Interface Status IP Address Speed MTU
    mgmt0 init 10.1.1.24/24 100 Mbps 1500
    MDS-switch-A# sh int mgmt 0
    mgmt0 is down (Initializing)
    Hardware is GigabitEthernet
    Address is 001a.e203.8af8
    Internet address is 10.1.1.26/24
    MTU 1500 bytes
    0 packets input, 0 bytes
    0 multicast frames, 0 compressed
    0 input errors, 0 frame, 0 overrun 0 fifo
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 fifo
    0 carrier errors

    hmm not sure where they 4 came from..but here is the status now..still in init..and here is the config..etc..
    Interface Status IP Address Speed MTU
    mgmt0 init 10.1.1.26/24 100 Mbps 1500
    XP-24000-MDS-switch-A# sh run int mgmt 0
    version 3.2(2c)
    interface mgmt0
    ip address 10.1.1.26 255.255.255.0
    XP-24000-MDS-switch-A# sh int mgmt 0
    mgmt0 is down (Initializing)
    Hardware is GigabitEthernet
    Address is 001a.e203.8af8
    Internet address is 10.1.1.26/24
    MTU 1500 bytes
    0 packets input, 0 bytes
    0 multicast frames, 0 compressed
    0 input errors, 0 frame, 0 overrun 0 fifo
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 0 fifo
    0 carrier errors

  • Upgrade IOS on 3550 w/ Gig ports

    Good morning,
    I am in the middle of IOS upgrades and kind of stuck! I have a 3550 that has 12 gig interfaces, 10 of which are fiber and 2 of which are copper interfaces. I want to try to minimize the amount of downtime as much as possible. Obviously it's going to come down when I have to reload.
    Here is my question. Is there a way for me to upgrade the IOS from one of the 10 Gig fiber interfaces? I tried using a media converter (fiber to copper) to connect my laptop to the switch, but I couldn't get the interface to come up. The media converter is 10/100Mbps and I couldn't find a way to change the speed on the interface of the switch to match that. Both copper interfaces are currently being used. The device is unmanaged so I cannot upgrade it remotely.
    Thanks!
    Colin

    hi
    I dont think you can make use of a media converter which is different in speed when compared to the port speed of the switch.
    If you have 10/100Mbps port connecting to the Gig port on the switch whichs again 1000Mbps the port wont come up at all and you wont be to get them synced...
    We did try something inline with this quite sometime back and failed with that.
    what i can suggest is to logon to the console port of the switch and configure a vlan ip.
    hook up your pc on any of the ethernet ports and configure on the same subnet to which the vlan belongs too.
    Check the ip reachability to the switch from the local pc and upload the ios using TFTP..
    regds

  • The red gige port on the bach of hhh

    Hi just got installed mon and the engineer told me I was getting 8o mb anyhow did my own speed test and it was more like 3omb ,and its been all over the place till today when it dropp below 8ookbs so I phoned technical and throu basically alternating switching the vdsl then the hhh it steadied out about 2ombs ,which he promised would improve ,I only live 1oo mtrs away from main bt box so I was expecting faster, Anyhow my next step was gonna connect my laptop and hhh to the gige port but he said this was only for state of the art laptops only and would not work, is this correct ? I apologise for my gramma.
    Thanks
    Solved!
    Go to Solution.

    Just an aside really - my son's snazzy new Samsung laptop works if wired into the gigabit port but gets no connection if wired into any other 100mbps ports.    No, I don't understand that either
    Note to mods - please get some decent smileys for this forum, the current ones suck

  • Workflow stuck in starting state after applying SharePoint 2010 CU December 2012

    I have custom visual studio workflow which are associated with Custom content type. workflow gets triggered automatically when a file is uploaded to SharePoint. Everything was working fine till when i apply the following CU
    http://blogs.msdn.com/b/joerg_sinemus/archive/2012/12/27/sharepoint-2010-and-december-2012-cu.aspx
    After applying this my workflow get stuck in "Starting" state.
    No error were logged in 14 hive logs.
    Thanks in Advance!

    It took me a while but I came up with a work around.  There is a PowerShell script below that can be used to trigger the workflow.  Hopefully this will hold all of us over until the official fix arrives.
    First remove the auto start on change or new from the affected workflow
    Edit the script below to match your environment
    Add the script to Windows task scheduler with the PowerShell.exe in the command line
    This assumes PowerShell.exe is in the path
    Then add the full path and script name in the add arguements text box
    Script:
    #The purpose of this script is to start the SPD workflow with the windows task scheduler for a trigger
    #This should avoid the check in-out issue caused by the December 2012 SP CU patch
    #This needs to be run on an account with membership in the farm administration group for SharePoint and Shell in SQL
    #You can use a find and replace to replace the server and other names with your actual names
    #There are no status messages being used since this will be a scheduled task in the Windows task scheduler
    #Add SharePoint modules and create variable space
    add-pssnapin microsoft.sharepoint.powershell
    start-spassignment -global
    #Open the web site, list and the workflow
    $site=get-spsite %site url%"
    $web=get-spweb %Web url%
    #Open the %affected% library or list and workflow association
    $%affected%=$web.getlist("%affected%")
    $manager=$site.workflowmanager
    $culture=[system.globalization.cultureinfo]::currentculture
    $wfname="%affected workflow name"
    $association=$%affected%.workflowassociations.getassociationbyname($wfname,$culture)
    $data=$association.associationdata
    $wfrunoption=[microsoft.sharepoint.workflow.spworkflowrunoptions]::synchronous
    #Start workflow
    foreach ($item in $%affected%.items) {
    $site.workflowmanager.startworkflow($item,$association,$data,$wfrunoption)
    stop-spassignment -global

  • Agent get stucked in Reserved State

    HI CUCCE gurus,
    Need assistance on this issue. In our remote office, our Sales Team has a linegroup setup, the Sales extensions are part of the linegroup and at the same time its their ACD line when they logged in to Cisco Agent Desktop.
    The issue is, when they got a call from the linegroup their CAD state change to "Reserved" and it stuck from that state and nothing they can do to change the state but to logoff, close the apps and log back in.
    I enabled debug on once of the Sales CAD (see attached output).
    Any troubleshooting tips that you can advise or detailed steps to check from our system.
    Our CAD is 7.X
    Our CUCCE is 7.X
    Our CUCM 7.X
    Thank you.

    Hi Jhun,
    Agent stuck in reserved state it means, the ICM has reserved the agent, but the call is not getting delivered to the agent extension.
    If you are using SIP trunk, you would probably need to check the CSS and Partitions over the trunk. Also, any recent changes made on the CSS of the SIP trunk you would need to reset the SIP trunk.
    The CSS on the SIP trunk should contain the partition of the phone.
    Also, you would need to check on the Agent targetting rule in the config manager of the ICM. The agent extensions should be added to the Agent targetting rule
    Hope this helps!!!
    Cheers,
    Dass
    Please rate useful posts

  • Campus Manager report - Ports in error Disabled state

    Hi,
    I have LMS 3.2 and I wonder how Campus Manager collects information from the switch to generate a report of discrepancies, namely a report of "Ports in Error Disabled state"??
    I find that I have ports in errDisabled state but Campus Manger doesn´t show this information in "Ports in Error Dissabled state" report. What could be the problem?
    Thanks.

    Hi,
    Campus Manager do snmpwalk on the ciscoErrDisableMIB to get the status of the error disabled ports.
    Thanks,
    Gaganjeet Singh

  • I have a set of 3 USB disk connected to my TC via a USB hud. I usually swithc the TC at night. When I restart the next day it stucks in amber state. when I disconnect the USB hub where my discs connects and restart, it start properly. Any hints?

    I have a set of 3 USB disks connected to my Time capsule (TC) via a USB hub. I usually switch the TC at night. When I restart the next day it stucks in amber state. When I disconnect the USB hub where my discs connects and restart, the TC will start properly. Any hints?

    LOL.. don't switch off the TC.. this is fairly typical behaviour..
    Or try a different usb hub.. but you could well and truly run out of hubs before you fix the problem.
    Are you running latest firmware for your TC?
    What error message is coming up in the airport utility.. amber led is a fault indicator.. look up what the actual fault is and see if it is for instance overloading the usb. You are using a powered hub??
    Get one bigger USB hard disk instead of 3 smaller ones.

  • LMS 3.0.1 / RME : bad speed value for giga port

    Hi,
    When we export inventory report from RME for a WS-CBS3020-HPQ.
    We can see that speed for giga port is wrong : 9.535107
    IOS version: Cisco IOS Software, CBS30X0 Software (CBS30X0-LANBASE-M), Version
    12.2(25)SEF1, RELEASE SOFTWARE (fc3)
    Thanks, Elisabeth

    Looks like you may have found a bug in the switch code, then.  I don't see anything relevant, but you are running fairly old code, and the problem may have been silently fixed in a newer release.  You should open a TAC service request so more analysis can be done.

  • Content Switching Module (CSM): Sessions stuck in closing state

    Hi guys,
    I'm troubleshooting a CSM with 4.3(1).
    We migrated a real server from windows to linux, since then lot's of sessions stuck in closing state until the idle timer expires.
    I traced the traffic from the client to the csm and from the csm to the real server what I saw is the following behaviour at the end of a session:
    windows real server: client sends FIN -> real server acks the FIN -> real server sends FIN -> client sends RST -> real server sends RST -> CSM deletes session from session table
    The linux real server mostly behaves like the windows real server but sometimes behaves as follows:
    client sends FIN -> real server sends  FIN, but does not ack the FIN sequence number of the client -> real server sends RST -> client sends RST -> CSM does not delete  session from session table, it stucks in closing state
    Does anybody know how I can solve this problem of half-closed sessions other than decreasing the idle timeout?
    Is it possible to configure CSM to close and delete sessions not only on FIN-ACK packets but also on RST packets?
    Or to use a different fast idle timeout when sessions are half-closed?
    Many thanks in advance,
    Thorsten

    Hi Fabrizio,
    CSM_FAST_FIN_TIMEOUT is already set to 10 seconds.
    What I found out while testing is that CSM_FAST_FIN_TIMEOUT works with configurations where idle timeout is configured > 0.
    But when idle timeout is configured to 0 (what meas no idle timeout) the csm seems not to use CSM_FAST_FIN_TIMEOUT: Half closed sessions will stuck in closing state.
    Any idea why cms behaves this way?
    Regards,
    Thorsten

  • Workflows stuck in "Starting" state.

    Workflows have been running fine for awhile.  All workflows are currently stuck in a "Starting" state.  Was finally able to capture this in ULS
    03/20/2014 11:58:23.46  w3wp.exe (0x15AC)                        0x2A98 SharePoint Foundation        
     Workflow Infrastructure        72fv Unexpected AutoStart Workflow: System.ArgumentException: Value does not fall within the expected range.     at Microsoft.SharePoint.Workflow.SPWorkflowActivationProperties..ctor(SPWorkflow
    workflow, String initiationData, Object context)     at Microsoft.SharePoint.Workflow.SPWorkflowManager.StartWorkflowElev(Object context, SPWorkflowAssociation association, DateTime elevationTimeUtc, SPWorkflowEvent startEvent, SPWorkflowRunOptions
    runOptions)     at Microsoft.SharePoint.Workflow.SPWorkflowAutostartEventReceiver.<>c__DisplayClass1.<AutoStartWorkflow>b__0(SPSite superUserSite, SPWeb superUserWeb) 
    Any ideas?
    TIA

    Hi Milo,
    Please check whether you have installed any CUs for SharePoint 2010.
    Please install June 2013 CU or higher for SharePoint 2010, compare the result.
    Here are some similar posts for you to take a look at:
    http://blogs.msdn.com/b/chaun/archive/2013/05/16/if-your-sp2010-workflows-are-stuck-in-the-starting-state.aspx
    http://social.technet.microsoft.com/Forums/sharepoint/en-US/5a6e6e83-b59f-4099-a86f-a07723ff2b98/workflow-stuck-in-starting-state-after-applying-sharepoint-2010-cu-december-2012?forum=sharepointadminprevious
    I hope this helps.
    Thanks,
    Wendy
    Wendy Li
    TechNet Community Support

  • [SOLVED] Mailbox import requests stuck in 'queued' state

    We have a small Exchange 2013 environment with one server having all roles. I try to import archive mailboxes from an Exchange 2010 environment. It has worked quite well for a while. However, all import requests are now 'stuck' in 'queued' state. Restart
    of Replication service, transport service and even server reboot didn't help.
    When I run
    get-mailboximportrequest | Get-MailboxImportRequestStatistics -Includereport | fl
    I observe that PositionInQueue value tells me that there are 85 import requests waiting :
    ItemsTransferred                       :
    PercentComplete                        : 0
    CompletedRequestAgeLimit               : 30.00:00:00
    PositionInQueue                        : 85/90 (Position/Queue Length)
    InternalFlags                          : None
    FailureCode                            :
    There should be no requests waiting as I removed all requests in advance before I issued new import requests:
    get-mailboximportrequest | Remove-MailboxImportRequest
    How can I really reset an import queue by zeroing PositionInQueue ?
    Any suggestions/tips?

    Hi,
    Glade to hear the good news. Thanks for your update.
    Best regards,
    If you have feedback for TechNet Subscriber Support, contact 
    [email protected]
    Belinda Ma
    TechNet Community Support

  • Ciscoworks daemon manager stuck at Stopping state

    I am working on LMS 3.2 . Tried to stop the daemon service with " net stop crmdmgtd ". It stuck on stopping state since few hours now. I can still open the application. Need a suggestion to terminate the previous command and restart the
    daemon service.

    You should have dmgtd.exe process in Task Manager stuck.
    Although you can kill it directly and then try the stop command once again before starting. But to be sure if any process in not stuck, best way would be to reboot the server once.

  • VM got stuck in "stopping" state, and cannot be stopped

    Dear all,
    I am using Oracle VM 3.2.2.
    One of my VM got stuck in "stopping" state, and cannot be stopped.
    How can I troubleshoot this problem...

    Q: Is the VM still running, i.e. can you ssh to the VM?
    Q: Find the server where the VM is running, and restart the ovs-agent, i.e. "service ovs-agent restart". Did this help, or is the agent crashed, any zombies?
    Possible root cause: These type of errors are typically ovs-agent bugs. First update oracle vm manager to the 3.2.4 release, not 3.2.6. Next update the dom0s to 3.2.4, not 3.2.6. You may need to setup a ULN 3.2.4 yum repo to update the dom0s. As you can see in these forms, 3.2.6 is may not ready for prime time, stick with 3.2.4, is stable.

  • Azure Cloud Service Stuck in "Stopping" state for a long time (12 hours)

    Does anyone have suggestions what to do with the issue I have. I tried to stop my Cloud Service the service is now basically stuck in "Stopping" State and been there over 12 hours. In my Cloud service there is 16 Virtual Machines I am using in
    testing.
    I tried to start Cloud Service but it also failed with error "Could not start the virtual machine deployment.".
    Is there something I could do or some way to get Microsoft Support (without paying extra)? I have "Visual Studio Premium with MSDN" so i have no other support but billing from Microsoft :(

    Managed to find the solution. I stopped and deallocated all the Virtual Machines. After that the Cloud Service status changed to stopped state. After that it was possible to start the Cloud Service again.

Maybe you are looking for