Heartbeat time outs some times caused by clocks-out-of-sync?
Heartbeat timeouts are usually caused by the java socket communication between the master and its slaves being slow (or dead).
This slowness in turn can be caused by a system being overloaded, something than can easily happen when we're running out of memory.
Memory problems can be caused by running against file system cache, which in turns eats up all memory, etc.
Some times the java socket connection between the master and remote hosts just is slow, also causing heartbeat timeouts.
Today I had a case where, in a multi-host situation, one of the remote hosts had his clock set five minutes early.
On the master this resulted in lots of 'slow getmessage' warnings telling you that it took longer than five seconds between the time the message was sent and that it was received. These timings use both the master and the remote host's current clock values.
In above case that always meant that every message was considered five minutes late.
Then, further on during the test the remote system's clock was reset and increased by five minutes.
That was it for the heartbeat timer, because it also uses the system's clock values.
So, if you run into heartbeat problems again, check your clocks.
In your 'xxxx-0.stdout.html' file you can verify, within reason, the clock settings, for instance:
11:52:19.013 11:47:17.605 task_run_all(): 395 tasks
11:57:39.004 11:57:39.000 Slow getMessage: hd2-0 1957 301404 REQUEST_SLAVE_STATISTICS
The first time value is the timestamp from the master at the time the message was received, the second is from the slave at the time that the message was sent, and as you can see, there is a five minute difference. The next message shows the now changed clock values.
The important message of this: make sure your clocks are synchronized in a multi-host environment.
Henk.
If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If all you see are messages that contain the word "Starting," you didn't clear the search box.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting.
Similar Messages
-
Different time in show clock and show calendar
Hi all,
I am having problem with figuring out how to adjust time between show calendar and show clock.
Basically time difference between this commands is roughly 40 minutes.
Please look on the screenshot:
Also my router configurations is:
! No configuration change since last restart
! NVRAM config last updated at 05:26:42 GMT Mon Dec 8 2014
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname RtrPod1
boot-start-marker
boot system usbflash0:c2800nm-advipservicesk9-mz.124-24.T1.bin
boot-end-marker
logging message-counter syslog
enable secret 5 $1$kABI$oyiPktODUDz4Ahdz7pCma0
no aaa new-model
clock timezone GMT 13
clock summer-time GMT recurring
clock calendar-valid
no network-clock-participate wic 1
network-clock-participate wic 2
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.110.0.1 10.110.0.10
ip dhcp excluded-address 10.115.0.1 10.115.0.10
ip dhcp pool Data
network 10.110.0.0 255.255.255.0
default-router 10.110.0.1
ip dhcp pool Voice
network 10.115.0.0 255.255.255.0
default-router 10.115.0.1
option 150 ip 10.115.0.1
no ip domain lookup
no ipv6 cef
ntp server 192.189.54.33
multilink bundle-name authenticated
voice-card 0
crypto pki trustpoint TP-self-signed-1408351535
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1408351535
revocation-check none
rsakeypair TP-self-signed-1408351535
crypto pki certificate chain TP-self-signed-1408351535
certificate self-signed 01
3082023F 308201A8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31343038 33353135 3335301E 170D3134 31323037 31363236
34325A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 34303833
35313533 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
81009EEF ADD1297E 7CD9BE3E 5BD3798D 10831172 0E025CB9 C7E57188 006DA7E1
E7B1D9A9 73EC5C53 841413DE E3E4AECD BC80C3D1 CC6BA113 B91CC736 16AF1576
F37F8437 C9577F4A 0AE72460 1E524E06 74E8DD39 E6952E1F 85547E71 1AD3DE5A
6DCB12E9 BD953716 13B41148 320EC307 9E45B084 80D0591A E49E8AE2 D87C0716
86430203 010001A3 67306530 0F060355 1D130101 FF040530 030101FF 30120603
551D1104 0B300982 07527472 506F6431 301F0603 551D2304 18301680 14880D89
51BCB633 B6F32385 71C9A39E 72149EAF 99301D06 03551D0E 04160414 880D8951
BCB633B6 F3238571 C9A39E72 149EAF99 300D0609 2A864886 F70D0101 04050003
8181001C 63A1BE6C BC96B738 05446ABC ACE19FBF 0054F6B5 100BA758 9A48FAF8
34B65325 3A374B08 2D8919BF 09ED604F 2F1B7A33 C25CFC7E 6DD55DA6 02CD7E78
4272ADF7 15158EDE 4A1115A9 06BBDA02 E65E5AC8 559103C4 98EF7371 20568663
ADF16711 60F8C5E0 ECDB5321 B3ABB8D5 2F42F19E 07D65ADF BABCDE63 50B43773 87AD10
quit
username student privilege 15 secret 5 $1$o8qC$cxUuwRjEtfvasjtjfNZAv/
archive
log config
hidekeys
controller E1 0/1/0
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.110
description Data VLAN
encapsulation dot1Q 110
ip address 10.110.0.1 255.255.255.0
interface GigabitEthernet0/0.111
description Management VLAN
encapsulation dot1Q 111
ip address 10.111.0.1 255.255.255.0
interface GigabitEthernet0/0.115
description Voice VLAN
encapsulation dot1Q 115
ip address 10.115.0.1 255.255.255.0
interface GigabitEthernet0/1
ip address dhcp
duplex auto
speed auto
interface Serial0/0/0
no ip address
shutdown
clock rate 2000000
interface BRI0/2/0
no ip address
interface BRI0/2/1
no ip address
interface Service-Engine1/0
no ip address
shutdown
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.15.1
ip http server
ip http authentication local
ip http secure-server
ip http path usbflash0:/gui
tftp-server usbflash0:phone/7942-7962/apps42.8-4-1-23.sbn alias apps42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/cvm42sccp.8-4-1-23.sbn alias cvm42sccp.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/jar42sccp.8-4-1-23.sbn alias jar42sccp.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/cnu42.8-4-1-23.sbn alias cnu42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/dsp42.8-4-1-23.sbn alias dsp42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/term42.default.loads alias term42.default.loads
tftp-server usbflash0:phone/7942-7962/term62.default.loads alias term62.default.loads
tftp-server usbflash0:phone/7942-7962/SCCP42.8-4-2S.loads alias SCCP42.8-4-2S.loads
tftp-server usbflash0:Desktops/320x196x4/big.png
tftp-server usbflash0:Desktops/320x196x4/small.png
tftp-server usbflash0:Desktops/320x196x4/List.xml
tftp-server usbflash0:Ringtones/Analog2.raw
tftp-server usbflash0:Ringtones/AreYouThere.raw
tftp-server usbflash0:Ringtones/AreYouTheref.raw
tftp-server usbflash0:Ringtones/Bass.raw
tftp-server usbflash0:Ringtones/CallBack.raw
tftp-server usbflash0:Ringtones/Classic1.raw
tftp-server usbflash0:Ringtones/Classic2.raw
tftp-server usbflash0:Ringtones/ClockShop.raw
tftp-server usbflash0:Ringtones/Drums1.raw
tftp-server usbflash0:Ringtones/Drums2.raw
tftp-server usbflash0:Ringtones/FilmScore.raw
tftp-server usbflash0:Ringtones/HarpSynth.raw
tftp-server usbflash0:Ringtones/Jamaica.raw
tftp-server usbflash0:Ringtones/KotoEffect.raw
tftp-server usbflash0:Ringtones/MusicBox.raw
tftp-server usbflash0:Ringtones/RingList.xml
tftp-server usbflash0:Ringtones/DistinctiveRingList.xml
tftp-server usbflash0:Ringtones/Piano1.raw
tftp-server usbflash0:Ringtones/Piano2.raw
tftp-server usbflash0:Ringtones/Pop.raw
tftp-server usbflash0:Ringtones/Pulse1.raw
tftp-server usbflash0:Ringtones/Ring1.raw
tftp-server usbflash0:Ringtones/Ring2.raw
tftp-server usbflash0:Ringtones/Ring3.raw
tftp-server usbflash0:Ringtones/Ring4.raw
tftp-server usbflash0:Ringtones/Ring5.raw
tftp-server usbflash0:Ringtones/Ring6.raw
tftp-server usbflash0:Ringtones/Ring7.raw
tftp-server usbflash0:Ringtones/Sax1.raw
tftp-server usbflash0:Ringtones/Sax2.raw
tftp-server usbflash0:Ringtones/Chime.raw
tftp-server usbflash0:Ringtones/Vibe.raw
control-plane
voice-port 0/2/0
voice-port 0/2/1
voice-port 0/3/0
voice-port 0/3/1
voice-port 2/0/0
voice-port 2/0/1
voice-port 2/0/2
voice-port 2/0/3
voice-port 2/0/4
voice-port 2/0/5
voice-port 2/0/6
voice-port 2/0/7
shutdown
mgcp fax t38 ecm
mgcp behavior g729-variants static-pt
telephony-service
max-ephones 5
max-dn 10
ip source-address 10.115.0.1 port 2000
load 7962 SCCP42.8-4-2S
max-conferences 8 gain -6
web admin system name webadmin secret 5 $1$MafG$7vShhmB.Tlfy22rnE88BK1
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 08 2014 05:26:39
line con 0
exec-timeout 120 0
password cisco
logging synchronous
login
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
exec-timeout 120 0
password cisco
logging synchronous
login local
transport input telnet ssh
line vty 5 15
exec-timeout 120 0
password cisco
logging synchronous
login local
transport input telnet ssh
scheduler allocate 20000 1000
end
And my switch configuration is:
! No configuration change since last restart
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname SwPod1
boot-start-marker
boot-end-marker
enable secret 5 $1$LDXy$1QdQ73kHv.8sQenQNMq19.
no aaa new-model
clock timezone GMT 13
clock summer-time GMT recurring
system mtu routing 1500
authentication mac-move permit
ip subnet-zero
no ip domain-lookup
crypto pki trustpoint TP-self-signed-2133227136
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2133227136
revocation-check none
rsakeypair TP-self-signed-2133227136
crypto pki certificate chain TP-self-signed-2133227136
certificate self-signed 01
3082023F 308201A8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32313333 32323731 3336301E 170D3933 30333031 30303030
35385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 31333332
32373133 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B71D E6CDD16E D6FEDB25 EC976368 7925A2F8 75EE3EF0 D4C371DA 4B5539BB
E3A9552F DE35F37B 45A2C5C4 30FEF8D7 C3C5C489 C08C8A90 B415D331 F4653100
DC1E0ECE D93B2BF5 339C7B3A D170B80A AFEE8DA9 A82263F9 6324F8FA 94BB253E
7B0B45D6 81E39078 1607DED1 85C69650 AB7D7419 96604F65 D9204BC8 1BC259BB
6D0B0203 010001A3 67306530 0F060355 1D130101 FF040530 030101FF 30120603
551D1104 0B300982 07537750 6F64312E 301F0603 551D2304 18301680 14C16878
2994DA55 82E0FAD0 046CED6D 0EBDA0EE AA301D06 03551D0E 04160414 C1687829
94DA5582 E0FAD004 6CED6D0E BDA0EEAA 300D0609 2A864886 F70D0101 04050003
81810090 C6829BAE 9B2A3A31 2A32C1FB AC7946E5 287A43B6 EC9F31D5 13296A2E
1810E5EB 2503617C C4CCDF9D 421E2372 E94A8BFA D73AB361 46BF80E4 B2C3E828
6DB62E7F DE5E0F6F B93A885E 3A5E13CA 6D95426C 9494C22D 005E8BC9 C6C012D5
DF186CFB 194BC416 89566F98 0C21CC79 D477022C A4845D94 EE0FC299 7C7710C5 32F314
quit
spanning-tree mode pvst
spanning-tree etherchannel guard misconfig
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/3
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/4
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/5
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/6
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/7
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/8
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/9
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/10
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/11
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/12
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/13
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/14
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/15
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/16
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/17
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/18
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/19
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/20
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/21
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/22
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/23
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/24
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface GigabitEthernet0/1
interface GigabitEthernet0/2
interface Vlan1
no ip address
shutdown
interface Vlan111
ip address 10.111.0.2 255.255.255.0
ip default-gateway 10.111.0.1
ip classless
ip http server
ip http secure-server
ip sla enable reaction-alerts
line con 0
exec-timeout 120 0
password cisco
logging synchronous
login
line vty 0 4
exec-timeout 120 0
password cisco
logging synchronous
login
line vty 5 15
exec-timeout 120 0
password cisco
logging synchronous
login
ntp clock-period 36028575
ntp server 10.110.0.1
end
Any help will be highly appreciated.Have you tried using "ntp update-calendar"?
-
About +ive Time Mgmt with Clock Time .
Hi SAP-HR Experts .
Plz give me idea about +ive Time Mgmt with Clock Time.
I maintained , Infotype 50 , (created from 01.04.2007)
When i tried to maintained Infotype 2011 . (from 01.04.2007) record is not created , it gives
warning (date is with in selection period) when i press Enter Key over it , No record is created in infotype 2011 .
I sat feature TMSTA = 1 .
In infotype 7 , i maintained Time Mgmt status = 1 .
I want to know what Time Evaluation Report (RPTIME00) will give to me ?
How do i confirm my self that now SAP-HR is running on +ive Time Mgmt with Clock Time.?
Please guide me ...
Regards : Rajneesh (9873607039)
Edited by: Rajneesh Kumar on Nov 18, 2008 6:02 AMHi Rajneesh,
When you run time evaluation through PT60 schema TM00 you will get the following:
1. Clock in and Clock out entry
All recorded time data documenting the actual attendance times or the actual absence times of employees.
Actual time has the opposite meaning of planned working time.
Example:
According to the work schedule, an employee is supposed to work from 8:00 a.m. to 5:00 p.m. on December 3, 1999 (planned working time). The actual time data (actual times) from this day is shown below:
8:00 a.m. to 2:30 p.m. Attendance
2:00 p.m. to 5:00 p.m. Absence - doctor's appointment
2. SKELETON TIME
skeleton time is a time account in which payment-related times of an employee are managed.
Skeleton time is determined in time evaluation.
Example:
Skeleton time in the standard SAP System consists of:
u2022 Attendance, absence, and off-site work within a contractual period (start and end of working time)
u2022 Overtime hours that exceed approved overtime
u2022 Paid break times
3. FLEXTIME
Working time pattern in which employees can individually determine their own start and end times, as long as a certain number of hours is worked within a defined period of time each day.
*4. FILL TIME
A specific period of working time described in time evaluation that lies within the contractual start and end of working time (excluding breaks).
If an employee works a flextime schedule and is also expected to be at work at certain times (core times), then fill time indicates the difference between the start and end of working time (without breaks) and the core times
5. PRODUCTIVE TIME
The usable working time for a resource. The system determines the productive time using the working time data and utilization rate for the resource as follows:
Productive time = (End of working time - start of working time - break
duration) x Rate of utilization / 100%.
You estimate the downtime at the resource using the utilization rate.
And the results of the following will depend on your settings...
Time evaluation will update the quotas and it will form time balances
I hope this information is enough to understand...for more clarifications revert to me..
Regards,
KPJ -
My time of day clock gains several minutes per day. It is set for automatic update but does so only when I bring up the preference. The computer is on nearly all the time so a dead battery doesn't seem likely. This topic was mentioned some time ago in this forum but I didn't see a final conclusion. Was this ever resolved?
This seems to be a recent phenomenon. I've made no recent system updates nor any other changes. It doesn't seem to do any harm but is an irritation.i would think it would be hardware-related as well. i would try a couple more things. i would boot to open firmware holding apple-option-o-f and then type in the following commands--
reset-nvram (hit return)
set-defaults (hit return)
reset-all (hit return)
the last command restarts the computer. i would also try a pmu reset to see if it helps. i'm not sure, but you seem to have a flat panel imac. if so, instructions for the reset are here. http://docs.info.apple.com/article.html?artnum=95165. this is, of course, if you feel comfortable going inside the computer. it is not that big of a deal. just make sure if you do this you ground yourself by touching metal and letting go of it before removing power cord and before touching the logic board. i am thinking maybe this could be the system clock, not the one viewed on the computer, but the crystal (or one of them, if there is more than one) on the logic board regulating frequency like a crystal in a watch would. i'm using the pc term. i'm assuming it's the same or pretty similar on a mac. [ 8 ) ] -
After 2 plus flawless years my mobo has developed its first issue. All of a sudden the time of day clock loses 20 minutes a day. Normally this would not be a big deal, but my banking software won't lock up with the server if the windows clock is more than an hour off. I've replaced the battrery, but that did not fix the issue. Am I missing something?
Quote from: syncman on 18-November-10, 01:08:27
I took a shot and invested $3 in another (2nd one) mobo battery. It fixed the "running slow" problem. Apparently the Energizer battery I replaced the OEM battery with was bad (low voltage) right out of the package. So much for the "Energizer bunny"!
Check date codes on replacement batteries. A few months back I went to a local retailer to purchase new coin cell batteries and they were all expiring in 2010. Bad. Went to another shop and got the same thing expiring in 2015. -
Flash/Youtube videos - sound out of sync over time -[CHROME]
Hi - i have some problems with videos in Chrome - when i watch videos - the sound gets out of sync from the video over time - in the start of the video the sound is perfect in sync - but after about 7 min the sound plays around 1-3 seconds before the video. it seems like the sound is playing at 100% speed but the video is only playing at 99% speed so the sound slowly gets more and more out of sync - have tried disableling flash in chrome in chrome://plugins but no result - have updated drivers
A/V sync is hard, and there are hundreds of ways to encode a video. Adobe provides guidance on how to best publish content to ensure that it consistently plays back well, but that's an uphill battle.
A direct link to the problem video is the most useful information you could provide in this case, along with details about your system. It would also be useful to know if the A/V sync problem goes away if you disable hardware acceleration, as described in the video troubleshooting guide.
https://helpx.adobe.com/flash-player/kb/video-playback-issues.html
Thanks! -
Any IDEA of Getting Server Time & RUn JavaScript Clock
Hi ,
Any idea of getting Server Time & running javascript Clock
I tried using ..
var tDate=<%=new java.util.Date()%>;
But it is not working
Plz helpYou can create a date in javascript like this
new Date(year, month, day, hours, minutes, seconds, milliseconds) You don't have to supply all the parameters (this is javascript after all)
Getting it from java, into javascript...
<%
java.util.SimpleDateFormat sdf = new java.util.SimpleDateFormat("yyyy,MM,dd,HH,mm,ss,SS");
Date now = new Date();
String sNow = sdf.format(now);
%>
var tDate = new Date(<%=sNow %>) -
1 hour clip in time-line goes gradually out of sync
Hello,
I captured a one hour mini-DV tape to a G4 Powerbook as one clip in FCP 4.5. As it plays in the timeline, it gradually goes out of sync and eventually goes way out of sync. Why would this happen? The tape itself plays fine in the camera and as it was captured it appeared to be in in sync all the way through. Thanks.
JonathanMini dv does not lock the audio to the picture, so over a period of time you'll get sync drift. Check to see that your sequence settings for audio match the camera's. FCP defaults at 48k. if you shot at 32k (12 bit), than on a long capture your audio will drift out of sync. You can create a sequence that is 32k, that might help but it looks like you'll have to move the audio track possibly in sections to get it back into sync.
-
Audio and Video are out of sync after time remaping.
After I did the time remap,audio and video are completely out of sync.
I don't know what I did wrong.Please HELP.
I did a short video(43seg) to explain myself better
http://www.youtube.com/watch?v=X0PQEoZvGbkha. having the video is killer. there are a couple ways to do this. i'd recommend using the blade tool (tap b twice to get the one that cuts all tracks), make a cut through the audio and the video at the points where you want it sped up, then right click the clip itself (which should be linked with audio and video) and then just set it to whatever speed you want. it'll have the same effect. you might have to adjust boundaries or you can select ripple.
alternatively, it looks like you just needed to do the same thing to the audio that you did to the video in that clip you uploaded. you can always relink things by selecting the audio and video and hitting cmnd+L.
hope that helps. -
When I create a key and send it to the person I want to begin communicating with encryption, the other person gets this when importing the key: "Error - key importing failed
gpg: key 5D391D97 was created 55491 seconds in the future (time warp or clock problem)"
The clock is set properly. Can you assist me in solving this error? This happens in a PC computer running WIndows 7.
Thank you
CeciliaI created a different key and I have the same problem. I can send you the public key in case that helps solve the problem but you need to provide me with an email address because I cannot upload it here.
Thank you for your assistance.
Cecilia -
Sending a meeting invite from Exchange 2007 account located in Central Time from Outlook 2010 Email Client located in Eastern Time cause meeting to show up 1 hour early on iPhone.
The meeting invite is being sent from a Computer through the Outlook 2010 Email Client. Both Computer and Outlook 2010 are set to Eastern Time. The OWA (Outlook Web Access) for the 2007 account is set to Eastern Time. The Outlook 2010 Email Client is connected to an Exchange 2007 account and the Exchange server for the exchange 2007 account is located in Chicago (Central Time) and is set to Central Time. When the meeting invite is sent from the Outlook 2010 Client the recipient receives the invite on his/her iPhone(set and located in the Eastern Time Zone) and a mime-attachment.ics file is attached to the meeting invite email. There is no info displayed in the subject line or message body. If the iPhone user opens the attachment it displays the meeting date and time and any other info that was sent from Outlook. The Outlook 2010 user sets the meeting for 10:00am to 11:00am. when the meeting invite mime-attachment.ics file is opened on the iPhone the meeting is displayed as 9:00am to 10:00am. if the iPhone user adds the ics file to his/her calendar it adds a meeting event that is scheduled 1 hour earlier than it is supposed to be. I had the iPhone user to set Time Zone support on and off and there is no change.
-
My adobe pro cc 2014 time line 82 minutes keep going out of sync ?
My adobe pro cc 2014 time line 82 minutes keep going out of sync?
More information needed for someone to help... please click below and provide the requested information
-Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840
Exactly what is INSIDE the video you are editing?
Codec & Format information, with 2 links inside for you to read http://forums.adobe.com/thread/1270588
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
https://forums.adobe.com/thread/1070933 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download
Does your video use a VARIABLE Frame Rate or a Constant Frame Rate? -
Icalender out of sync with times.
In icalender, If i put in 10am wednesday it says 12 pm wednesday on my iphone. times are out of sync. Help.
everytime
-
What is meant by Positive time mgt with clock & without clock?
Hi Experts
What is meant by Positive time mgt with clock & without clock? Plz explain with example experts..Hello Anniyan,
Please check the below thread. Its a good beginner.
Positive & Negative Time Management Concept
Please rewar if helpful.
Thanks and Best Regards.
Karan. -
Quick time export Audio out of sync
Exporting a quicktime movie (a 30 min timeline HDV 720P) for importation into Compressor, parts of the audio loose sync. The timeline is in sync.
Using latest versions of FCP and Quicktime. Pro 2.8 dual Qaud with 10gb ram
It appears to be intermittent as I have exported other similar timelines with out problem. I am trying compressor directly but as we all know that may take most of the day even using the clusters on the macThis out of sync problem could be related to the
klyte codec I installed which may have created problem. or something went
wrong in audio capture as it should have been a sterio file as you
mentioned.
For some, the K-Lite CODEC Pack works fine. For many more, and this might well depend on which of its elements one installs, it is a total disaster. Again, depending on what has been installed, a simple uninstall of the elements might work. In some other cases, it will take much more work to clean up after it.
My best advice is to only install CODEC's on a "need" basis. I also attempt to go to the source for my CODEC's, even if that means passing up a free one, for a paid one. If at all possible, I want no hacked, or reverse-engineered CODEC's on any of my systems.
Good luck, and do please try a Project with the proper Preset, and footage captured either in Pr or HDVSplit. Let's see if, with Pinnacle our of the way, you get better results. Please report.
Hunt
Maybe you are looking for
-
Firefox keeps crashing on start-up
Since Sunday evening (3-3-13) Firefox immediately crashes when I try to start: The windows that is opened just freezes and sometimes it doesn't even open at all (although the process is running). Curious thing is that when I remove Firefox and re-ins
-
Hi, I have a problem with JTable. ...i have just started working with JTables and still have not got a complete hang of how they function. I have a table whose model is "AbstractTableModel". I have different data in each row of the table therefore i
-
I do not know how to save emails to keep them from being delete when cleaning up my messages. How do I sequester certain messages so this does not happen? Thanks
-
Since I installed LR2, CS3 won't print any more. I worked already with LR1.4 and LR2beta. When I give a print command in CS3 I get two warnings: first that I have to install a printer and second that the print command can not be completed because of
-
Why are certain fonts not loading in my fontbook
I am having issues loading fonts into my fontbook - and onto my system. Oddly, one of these fonts is Helvetica. I am running on Mac OSX 10.7.5 - Intel Core i5. Version of fontbook: Version 198.4 (198) If anyone has any ideas of why this is happening,